Using a VLAN other than VLAN 1

Version 1
    This document was generated from CDN thread

    Created by: SCOTT PITTS on 23-03-2011 11:30:12 AM
    Can I use a VLAN other than 1 for the SRE? I tried VLAN 350 but the VLAN 350 will not seem to go up/up
     
    Here is the config:
     
    !        
    interface SM1/0
     ip address 10.26.143.50 255.255.255.192
     service-module fail-open
     service-module ip address 10.26.143.51 255.255.255.192
     service-module ip default-gateway 10.26.143.50
     service-module mgf ip address 10.26.143.150 255.255.255.192 vlan 350
     service-module mgf ip default-gateway 10.26.143.145 vlan 350
    !        
    interface SM1/1
     description Internal switch interface connected to Service Module
     switchport mode trunk
    !        
    interface Vlan1
     no ip address
    !        
    interface Vlan350
     ip address 10.26.143.145 255.255.255.192

     
    Show IP int brief:
    Routert#show ip int brief
    Interface                  IP-Address      OK? Method Status                Protocol
    GigabitEthernet0/0         10.25.128.1     YES NVRAM  up                    up     
    GigabitEthernet0/1         unassigned      YES NVRAM  down                  down   
    GigabitEthernet0/1.301     10.26.128.1     YES NVRAM  down                  down   
    GigabitEthernet0/1.400     10.26.129.1     YES NVRAM  down                  down   
    GigabitEthernet0/2         unassigned      YES NVRAM  administratively down down   
    Serial0/0/0:0              unassigned      YES NVRAM  up                    up     
    Serial0/0/0:0.207          152.161.67.190  YES NVRAM  up                    up     
    Serial0/0/1:1              194.178.102.46  YES NVRAM  up                    up     
    SM1/0                      10.26.143.50    YES manual up                    up     
    SM1/1                      unassigned      YES unset  up                    up     
    Loopback0                  172.26.38.121   YES NVRAM  up                    up    
    NVI0                       194.178.102.46  YES unset  up                    up     
    Tunnel2515                 192.168.195.62  YES NVRAM  up                    up     
    Virtual-Access1            unassigned      YES unset  down                  down   
    Virtual-Template100        unassigned      YES unset  down                  down   
    Vlan1                      unassigned      YES NVRAM  up                    up     
    Vlan350                    10.26.143.145   YES manual up                    down   
     
    I loaded the SRE image fine and the license is installed (rebooted after install). VLAN1 on the LAN is GIG 0/0 so I wanted to use something else to avaoid confusion.
     
     
    SYSTEM ONLINE
    se-10-26-143-51# show lic
    Index 0 Feature: SRE-V-HOST-LIC
            Period left: Life time
            License Type: Permanent
            License State: Active, In Use
            License Count: Non-Counted
            License Priority: Medium
    Index 1 Feature: SRE-V-RMA-LIC 
            Period left:  0 minute   0 second 
    se-10-26-143-51#

    Subject: RE: New Message from SCOTT PITTS in Service Ready Engine Virtualization - T
    Replied by: Radhika Miriyala on 23-03-2011 12:20:24 PM
    Hi Scott,

    With SRE-v 1.0.1 release the Hypervisor IP address that is the one you assign to Service-module mgf ip address xxxx¿ has to be in Vlan 1. 



    Thanks,

    Radhika







    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Wednesday, March 23, 2011 8:30 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from SCOTT PITTS in Service Ready Engine Virtualization - Technical Questions: Using a VLAN other than VLAN 1



    SCOTT PITTS has created a new message in the forum "Technical Questions":

    --------------------------------------------------------------
    Can I use a VLAN other than 1 for the SRE? I tried VLAN 350 but the VLAN 350 will not seem to go up/up

    Here is the config:

    !        
    interface SM1/0
    ip address 10.26.143.50 255.255.255.192
    service-module fail-open
    service-module ip address 10.26.143.51 255.255.255.192
    service-module ip default-gateway 10.26.143.50
    service-module mgf ip address 10.26.143.150 255.255.255.192 vlan 350
    service-module mgf ip default-gateway 10.26.143.145 vlan 350
    !        
    interface SM1/1
    description Internal switch interface connected to Service Module
    switchport mode trunk
    !        
    interface Vlan1
    no ip address
    !        
    interface Vlan350
    ip address 10.26.143.145 255.255.255.192


    Show IP int brief:
    Routert#show ip int brief
    Interface                  IP-Address      OK? Method Status                Protocol
    GigabitEthernet0/0         10.25.128.1     YES NVRAM  up                    up     
    GigabitEthernet0/1         unassigned      YES NVRAM  down                  down   
    GigabitEthernet0/1.301     10.26.128.1     YES NVRAM  down                  down   
    GigabitEthernet0/1.400     10.26.129.1     YES NVRAM  down                  down   
    GigabitEthernet0/2         unassigned      YES NVRAM  administratively down down   
    Serial0/0/0:0              unassigned      YES NVRAM  up                    up     
    Serial0/0/0:0.207          152.161.67.190  YES NVRAM  up                    up     
    Serial0/0/1:1              194.178.102.46  YES NVRAM  up                    up     
    SM1/0                      10.26.143.50    YES manual up                    up     
    SM1/1                      unassigned      YES unset  up                    up     
    Loopback0                  172.26.38.121   YES NVRAM  up                    up    
    NVI0                       194.178.102.46  YES unset  up                    up     
    Tunnel2515                 192.168.195.62  YES NVRAM  up                    up     
    Virtual-Access1            unassigned      YES unset  down                  down   
    Virtual-Template100        unassigned      YES unset  down                  down   
    Vlan1                      unassigned      YES NVRAM  up                    up     
    Vlan350                    10.26.143.145   YES manual up                    down   

    I loaded the SRE image fine and the license is installed (rebooted after install). VLAN1 on the LAN is GIG 0/0 so I wanted to use something else to avaoid confusion.


    SYSTEM ONLINE
    se-10-26-143-51# show lic
    Index 0 Feature: SRE-V-HOST-LIC
            Period left: Life time
            License Type: Permanent
            License State: Active, In Use
            License Count: Non-Counted
            License Priority: Medium
    Index 1 Feature: SRE-V-RMA-LIC 
            Period left:  0 minute   0 second 
    se-10-26-143-51#


    --
    To respond to this post, please click the following link:

    <http://developer.cisco.com/web/srev/forums/-/message_boards/view_message/3241293>

    or simply reply to this email.

    Subject: RE: Using a VLAN other than VLAN 1
    Replied by: SCOTT PITTS on 23-03-2011 01:45:48 PM
    It is just that I do not know how to have VLAN1 and GIG0/0.1 (vlan 1) in the same IP range. Can I do the following:

    interface Vlan1
    ip unnumbered GIG0/0.1 (ip unnumbered GIG 0/0 in this case)

    Is this true in sre-v-k9.smv.1.0.2 or just sre-v-k9.smv.1.0.1?

    Subject: RE: New Message from Radhika Miriyala in Service Ready Engine Virtualizatio
    Replied by: John Voss on 23-03-2011 01:36:24 PM
    Scott,

    Just to clarify, the Hypervisor (ESXi Host) IP has to be in Vlan 1 in
    this release, but you can assign the Virtual Machines to other VLANs.

    For more information on this configuration see section 9.6 of the SRE-V
    Self Training Guide -
    http://www.cisco.com/en/US/prod/collateral/ps10265/ps11273/installation_
    guide_c07-640002.html or the configuring VLANs section of the SRE-V
    Installation Guide -
    http://www.cisco.com/en/US/docs/interfaces_modules/services_modules/sre_
    v/1.0/user/guide/interface.html#wp1108337

    If the VLAN 1 restriction for the ESXi Host IP is a problem, let me know
    - we may be able to change this in a future release.

    Best Regards,

    John

    ________________________________

    From: Cisco Developer Community Forums
    [mailto:cdicuser@developer.cisco.com]
    Sent: Wednesday, March 23, 2011 9:20 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Radhika Miriyala in Service Ready Engine
    Virtualization - Technical Questions: RE: New Message from SCOTT PITTS
    in Service Ready Engine Virtualization - T


    Radhika Miriyala has created a new message in the forum "Technical
    Questions":
    --------------------------------------------------------------
    Hi Scott,

    With SRE-v 1.0.1 release the Hypervisor IP address that is the one you
    assign to Service-module mgf ip address xxxx" has to be in Vlan 1.



    Thanks,

    Radhika







    From: Cisco Developer Community Forums
    [mailto:cdicuser@developer.cisco.com]
    Sent: Wednesday, March 23, 2011 8:30 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from SCOTT PITTS in Service Ready Engine
    Virtualization - Technical Questions: Using a VLAN other than VLAN 1



    SCOTT PITTS has created a new message in the forum "Technical
    Questions":

    --------------------------------------------------------------
    Can I use a VLAN other than 1 for the SRE? I tried VLAN 350 but the VLAN
    350 will not seem to go up/up

    Here is the config:

    !
    interface SM1/0
    ip address 10.26.143.50 255.255.255.192
    service-module fail-open
    service-module ip address 10.26.143.51 255.255.255.192
    service-module ip default-gateway 10.26.143.50
    service-module mgf ip address 10.26.143.150 255.255.255.192 vlan 350
    service-module mgf ip default-gateway 10.26.143.145 vlan 350
    !
    interface SM1/1
    description Internal switch interface connected to Service Module
    switchport mode trunk
    !
    interface Vlan1
    no ip address
    !
    interface Vlan350
    ip address 10.26.143.145 255.255.255.192
    !

    Show IP int brief:
    Routert#show ip int brief
    Interface IP-Address OK? Method Status Protocol
    GigabitEthernet0/0 10.25.128.1 YES NVRAM up up
    GigabitEthernet0/1 unassigned YES NVRAM down down
    GigabitEthernet0/1.301 10.26.128.1 YES NVRAM down down
    GigabitEthernet0/1.400 10.26.129.1 YES NVRAM down down
    GigabitEthernet0/2 unassigned YES NVRAM administratively down down
    Serial0/0/0:0 unassigned YES NVRAM up up
    Serial0/0/0:0.207 152.161.67.190 YES NVRAM up up
    Serial0/0/1:1 194.178.102.46 YES NVRAM up up
    SM1/0 10.26.143.50 YES manual up up
    SM1/1 unassigned YES unset up up
    Loopback0 172.26.38.121 YES NVRAM up up
    NVI0 194.178.102.46 YES unset up up
    Tunnel2515 192.168.195.62 YES NVRAM up up
    Virtual-Access1 unassigned YES unset down down
    Virtual-Template100 unassigned YES unset down down
    Vlan1 unassigned YES NVRAM up up
    Vlan350 10.26.143.145 YES manual up down

    I loaded the SRE image fine and the license is installed (rebooted after
    install). VLAN1 on the LAN is GIG 0/0 so I wanted to use something else
    to avaoid confusion.


    SYSTEM ONLINE
    se-10-26-143-51# show lic
    Index 0 Feature: SRE-V-HOST-LIC
    Period left: Life time
    License Type: Permanent
    License State: Active, In Use
    License Count: Non-Counted
    License Priority: Medium
    Index 1 Feature: SRE-V-RMA-LIC
    Period left: 0 minute 0 second
    se-10-26-143-51#


    --
    To respond to this post, please click the following link:

    <http://developer.cisco.com/web/srev/forums/-/message_boards/view_messag
    e/3241293>

    or simply reply to this email.
    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/web/srev/forums/-/message_boards/view_messag
    e/3241749>
    or simply reply to this email.

    Subject: RE: New Message from SCOTT PITTS in Service Ready Engine Virtualization - T
    Replied by: Radhika Miriyala on 23-03-2011 01:49:24 PM
    The same limitation holds for both 1.0.1 and 1.0.2



    You should be able to configure

    Interface Vlan 1

    ip unnumbered GIG 0/0





    Just note that once you do this you will have to add ip route  on the router for the mgf ip address you configure for the hypervisor.



    Thanks,

    Radhika





    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Wednesday, March 23, 2011 10:46 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from SCOTT PITTS in Service Ready Engine Virtualization - Technical Questions: RE: Using a VLAN other than VLAN 1



    SCOTT PITTS has created a new message in the forum "Technical Questions":

    --------------------------------------------------------------
    It is just that I do not know how to have VLAN1 and GIG0/0.1 (vlan 1) in the same IP range. Can I do the following:

    interface Vlan1
    ip unnumbered GIG0/0.1 (ip unnumbered GIG 0/0 in this case)

    Is this true in sre-v-k9.smv.1.0.2 or just sre-v-k9.smv.1.0.1?
    --
    To respond to this post, please click the following link:

    <http://developer.cisco.com/web/srev/forums/-/message_boards/view_message/3242114>

    or simply reply to this email.

    Subject: Re: New Message from SCOTT PITTS in Service Ready Engine Virtualization - T
    Replied by: Anurag Gurtu on 23-03-2011 08:35:24 PM
    IP unnumbered commands can't be used in iteration so cant do the following: A ip unnumbered on B unnumbered on C.

    You can use the config mentioned by Radhika.

    Thanks

    Anurag Gurtu