2951/SRE-V with 15.1.3T doesnt have service-module mgf command ...

Version 1
    This document was generated from CDN thread

    Created by: Josip Zimet on 04-03-2011 12:05:22 PM
    Dear alias members,
     
     I just received CISCO2951/K9 and SM-SRE-900-K9 from demo depot, installed c2951-universalk9-mz.SPA.151-3.T.bin downloaded from CDO and found out that IOS doesnt support mgf commands ... any idea ?
     
    Router#show diag | include FRU    
        Product (FRU) Number     : CISCO2951/K9
        Product (FRU) Number     : PWR-2921-51-POE
        Product (FRU) Number     : SM-SRE-900-K9
        Product (FRU) Number     : SM-ES3G-16-P
    Router#sh ver
    Cisco IOS Software, C2951 Software (C2951-UNIVERSALK9-M), Version 15.1(3)T, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2010 by Cisco Systems, Inc.
    Compiled Mon 15-Nov-10 23:12 by prod_rel_team
    ROM: System Bootstrap, Version 15.0(1r)M1, RELEASE SOFTWARE (fc1)
    Router uptime is 13 minutes
    System returned to ROM by reload at 16:53:33 UTC Fri Mar 4 2011
    System image file is "flash0:c2951-universalk9-mz.SPA.151-3.T.bin"
    Last reload type: Normal Reload
    Last reload reason: Reload Command
    Cisco CISCO2951/K9 (revision 1.0) with 999424K/49152K bytes of memory.
    Processor board ID FCZ1350721Q
    6 Gigabit Ethernet interfaces
    2 terminal lines
    1 Services Module (SM) with Services Ready Engine (SRE)
       Cisco Wide Area Application Services Software 4.3.1 (b6 Nov 13 2010 20:33:57) in slot 1
    DRAM configuration is 72 bits wide with parity enabled.
    255K bytes of non-volatile configuration memory.
    4099032K bytes of ATA System CompactFlash 0 (Read/Write)
    License Info:
    License UDI:
    -------------------------------------------------
    Device#      PID            SN
    -------------------------------------------------
    *0        CISCO2951/K9          FCZ1350721Q
    Router#conf t
    Enter configuration commands, one per line.  End with CNTL/Z.
    Router(config)#int sm 1/0
    Router(config-if)#service-module ?
      external  Service module external interface configuration
      ip        Service module ip configuration

    Router(config-if)#service-module
    Kind regards,
    josip Zimet

    Subject: Re: New Message from Radhika Miriyala in Service Ready Engine Virtualizatio
    Replied by: Josip Zimet on 04-03-2011 03:41:39 PM
    Hi Radhika,

    There is no HWIC ether switch installed on the router .. This is output of
    ³show version² ...

    Cisco CISCO2951/K9 (revision 1.0) with 999424K/49152K bytes of memory.
    Processor board ID FCZ1350721Q
    6 Gigabit Ethernet interfaces
    2 terminal lines
    1 Services Module (SM) with Services Ready Engine (SRE)
       Cisco Wide Area Application Services Software 4.3.1 (b6 Nov 13 2010
    20:33:57) in slot 1
    DRAM configuration is 72 bits wide with parity enabled.
    255K bytes of non-volatile configuration memory.
    4099032K bytes of ATA System CompactFlash 0 (Read/Write)
    ... Noticed that it lists Cisco WAAS Software !!!

    This is output of service module sm 1/0 status

    Router#service-module sm 1/0 status
    Service Module is Cisco SM1/0
    Service Module supports session via TTY line 67
    Service Module is in Steady state
    Service Module heartbeat-reset is enabled
    Getting status from the Service Module, please wait..
    Cisco Wide Area Application Services Software 4.3.1 (b6 Nov 13 2010
    20:33:57)
    Restarted at Fri Mar  4 14:34:27 2011

    Module resource information:
      CPU Frequency: 1862 MHz
      Memory Size: 4001244 MB
      Disk 0 Size: 500107 MB

    No install/uninstall in progress

    Local Partition Info - (0 apps)
    =====================
      Retrieving partition information

    Router#

    Kind regards,
    Josip Zimet

    Subject: RE: Re: New Message from Radhika Miriyala in Service Ready Engine Virtualiz
    Replied by: Brett Tiller on 04-03-2011 06:03:19 PM
    Hi Josip,

    Yes it appears that you were shipped a service module with WAAS pre-installed.  Did you order the module with SRE-V to be pre-installed?  If you can send the PO or Sales Order number we can check it.  Regarding getting SRE-V installed, first please uninstall WAAS via the router and then check if you can configure the service module.  Once completed you can then install SRE-V.  You can download SRE-V from our site http://developer.cisco.com/web/srev/docs .

    Thanks,

    Brett

    Subject: RE: New Message from Josip Zimet in Service Ready Engine Virtualization - T
    Replied by: Radhika Miriyala on 04-03-2011 12:09:39 PM
    Hi Josip,

    A couple of thing to check here:

    1)    Do you have HWIC ether switch on this router? If so what is the model number of the switch.

    2)    Do you know if the SRE has any image installed on it? Can you send us the output of ¿service-module x/0 status¿ command?

    Thanks,

    Radhika

    Subject: Re: New Message from Brett Tiller in Service Ready Engine Virtualization -
    Replied by: Josip Zimet on 06-03-2011 01:39:39 AM
    Hi Brett,

    As suggested I successfully uninstalled service-module

    Router#service-module sm 1/0 uninstall
    Delete the installed Cisco Wide Area Application Services Software
    permanently? : y
    Router#service-module sm 1/0 status
    Service Module is Cisco SM1/0
    Service Module supports session via TTY line 67
    Service Module is being Shutdown
    Service Module heartbeat-reset is enabled
    Service Module status is not available

    Module resource information:
      CPU Frequency: 1862 MHz
      Memory Size: 4001244 MB
      Disk 0 Size: 500107 MB

    Uninstall in progress

    Local Partition Info - (0 apps)
    =====================
      Retrieving partition information

    And I believe I can configure service-module
    Router#conf t
    Enter configuration commands, one per line.  End with CNTL/Z.
    Router(config)#int
    Router(config)#int sm 1/0
    Router(config-if)#serv
    Router(config-if)#service-m
    Router(config-if)#service-module ?
      external  Service module external interface configuration
      ip        Service module ip configuration

    Router(config-if)#service-module

    Install didn¹t work form home so will try it 1st thing on Monday

    Router#ping 10.60.92.117

    Type escape sequence to abort.
    Sending 5, 100-byte ICMP Echos to 10.60.92.117, timeout is 2 seconds:
    !!!!!
    Success rate is 100 percent (5/5), round-trip min/avg/max = 104/105/108 ms
    Router#$@10.62.63.66/Desktop/orchestrator/sre-v-k9.smv.1.0.1/sre-v-k9.smv.1.
    0.1.pkg^@      
    Proceed with installation? :
    Router#$@10.62.63.66/Desktop/orchestrator/sre-v-k9.smv.1.0.1/sre-v-k9.smv.1.
    0.1.pkg
    Proceed with installation? : y
    %Error: Couldn't open
    ftp://*****:*****@10.62.63.66/Desktop/orchestrator/sre-v-k9.smv.1.0.1/sre-v-
    k9.smv.1.0.1.pkg.install.sre
    Execution of script sre-v-k9.smv.1.0.1.pkg.install.sre failed, installation
    aborted
    Router#


    Rgds
    Josip Zimet

    Subject: RE: New Message from Josip Zimet in Service Ready Engine Virtualization - T
    Replied by: Herwind garcia on 13-04-2011 05:40:42 PM
    Hi, Radhika,
    I can't find "mgf" and "switchport" in order to configure SM-SRE.
     
    Router model: 2911
    #show diag | include FRU
        Product (FRU) Number     : CISCO2911/K9
        Product (FRU) Number     : PWR-2911-AC
        Product (FRU) Number     : HWIC-4ESW
        Product (FRU) Number     : ILPM-4
        Product (FRU) Number     : HWIC-1T
        Product (FRU) Number     : SM-SRE-700-K9
     
    As you can see, I have HWIC ether switch in it. Is there any kind of incompatibility? I know about isues with PVDM modules, but i haven't any.
     
    Output for "show version":
    ==================
    #show version
    Cisco IOS Software, C2900 Software (C2900-UNIVERSALK9-M), Version 15.1(3)T, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2010 by Cisco Systems, Inc.
    Compiled Mon 15-Nov-10 22:51 by prod_rel_team

    ROM: System Bootstrap, Version 15.0(1r)M9, RELEASE SOFTWARE (fc1)

    ISR-2911-ROMULO-GALLEGOS uptime is 5 days, 7 hours, 34 minutes
    System returned to ROM by power-on
    System image file is "flash:c2900-universalk9-mz.SPA.151-3.T.bin"
    Last reload type: Normal Reload


    This product contains cryptographic features and is subject to United
    States and local country laws governing import, export, transfer and
    use. Delivery of Cisco cryptographic products does not imply
    third-party authority to import, export, distribute or use encryption.
    Importers, exporters, distributors and users are responsible for
    compliance with U.S. and local country laws. By using this product you
    agree to comply with applicable laws and regulations. If you are unable
    to comply with U.S. and local laws, return this product immediately.

    A summary of U.S. laws governing Cisco cryptographic products may be found at:
    http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

    If you require further assistance please contact us by sending email to
    export@cisco.com.

    Cisco CISCO2911/K9 (revision 1.0) with 475136K/49152K bytes of memory.
    Processor board ID FTX1504AK18
    4 FastEthernet interfaces
    3 Gigabit Ethernet interfaces
    1 Serial(sync/async) interface
    1 terminal line
    1 Services Module (SM) with Services Ready Engine (SRE)
    DRAM configuration is 64 bits wide with parity enabled.
    255K bytes of non-volatile configuration memory.
    254464K bytes of ATA System CompactFlash 0 (Read/Write)


    License Info:

    License UDI:

    -------------------------------------------------
    Device#      PID            SN
    -------------------------------------------------
    *0        CISCO2911/K9          FTX1504AK18    



    Technology Package License Information for Module:'c2900'

    ----------------------------------------------------------------
    Technology    Technology-package          Technology-package
                  Current       Type          Next reboot 
    -----------------------------------------------------------------
    ipbase        ipbasek9      Permanent     ipbasek9
    security      None          None          None
    uc            None          None          None
    data          None          None          None

    Configuration register is 0x2102

     
    Thanks,
    Herwind Garcia
     
    Hi Josip,

    A couple of thing to check here:

    1)    Do you have HWIC ether switch on this router? If so what is the model number of the switch.

    2)    Do you know if the SRE has any image installed on it? Can you send us the output of ¿service-module x/0 status¿ command?



    Thanks,

    Radhika

    Subject: RE: New Message from Herwind Garcia in Service Ready Engine Virtualization
    Replied by: Radhika Miriyala on 14-04-2011 12:18:25 PM
    Hi Herwind,

    It looks like you have a older generation HWIC ether switch. When this is present in the router than you will not be able to use MGF as designed. You will have to follow a different procedure for configuring.

    You will need to configure the Hypervisor IP address under ¿interface sm x/1¿ where x is the slot number of your Service module.

    Here is a sample of the config:

    interface SM1/1

    ip address 10.10.10.1 255.255.255.0

    service-module ip address 10.10.10.2 255.255.255.0

    The IP address of the hypervisor or esxi is 10.10.10.2 in the above example. You can use that to connect to vSphere client. You can find complete procedure to do this in the our User documentation at: http://www.cisco.com/en/US/docs/interfaces_modules/services_modules/sre_v/1.0/user/guide/app_interface.html

    You will basically have to follow the IOS 15.1 (2) T configuration here.

    Please let us know if you have any questions,

    Thanks,

    Radhika

    Subject: RE: New Message from Herwind garcia in Service Ready Engine Virtualization
    Replied by: Radhika Miriyala on 14-04-2011 08:10:25 PM
    Herwind,

    Can you manually issue 'no shut' on the interface sm 1/1 and do a 'write' on the router to save the config. I think the 'no shut' step might be missing from the document.

    You may also need to add a route to reach the 20.0.0.2 network on your workstation. 

    Let me know if the above two steps don't work for you.

    Thanks,

    Radhika

    Subject: RE: New Message from Josip Zimet in Service Ready Engine Virtualization - T
    Replied by: Herwind garcia on 14-04-2011 03:57:06 PM
    Hi Radhika,
    Thanks for your help.

    setting ip address on SM1/1 throws this error:
    % IP addresses may not be configured on L2 links SM1/1.

    I have tried commands like: no switchport, no switchport mode trunk, no switchport mode access, no switchport trunk allowed vlan, and not success.

    Thanks,
    Herwind Garcia

    Subject: RE: New Message from Herwind garcia in Service Ready Engine Virtualization
    Replied by: Radhika Miriyala on 14-04-2011 04:23:25 PM
    Hi Herwind,

    Just to confirm you are not seeing  the CLI ¿service-module mgf ip address¿ and at the same you are also not configure IP address in under service-module SM 1/1 .



    If the above is correct I am not sure what exactly is happening here. We will try to reproduce this in our lab. But mean while can you try removing the HWIC ESW and see what the behavior is?



    Thanks,

    Radhika





    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Thursday, April 14, 2011 12:57 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Herwind garcia in Service Ready Engine Virtualization - Technical Questions: RE: New Message from Josip Zimet in Service Ready Engine Virtualization - T



    Herwind garcia has created a new message in the forum "Technical Questions":

    --------------------------------------------------------------
    Hi Radhika,
    Thanks for your help.

    setting ip address on SM1/1 throws this error:
    % IP addresses may not be configured on L2 links SM1/1.

    I have tried commands like: no switchport, no switchport mode trunk, no switchport mode access, no switchport trunk allowed vlan, and not success.

    Thanks,
    Herwind Garcia
    --
    To respond to this post, please click the following link:

    <http://developer.cisco.com/web/srev/forums/-/message_boards/view_message/3673432>

    or simply reply to this email.

    Subject: RE: New Message from Herwind garcia in Service Ready Engine Virtualization
    Replied by: Herwind garcia on 14-04-2011 04:36:23 PM
    Hi Radhika,
     
    I'm sorry, I have unplugged HWIC module in order to test if command ¿service-module mgf ip address¿ works, it was a test suggested by Anurag and I haven't installed yet.

    Let me install it again to test and post results here.
     
    Thanks,
    Herwind Garcia
     
    Hi Herwind,

    Just to confirm you are not seeing  the CLI ¿service-module mgf ip address¿ and at the same you are also not configure IP address in under service-module SM 1/1 .



    If the above is correct I am not sure what exactly is happening here. We will try to reproduce this in our lab. But mean while can you try removing the HWIC ESW and see what the behavior is?



    Thanks,

    Radhika





    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Thursday, April 14, 2011 12:57 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Herwind garcia in Service Ready Engine Virtualization - Technical Questions: RE: New Message from Josip Zimet in Service Ready Engine Virtualization - T



    Herwind garcia has created a new message in the forum "Technical Questions":

    --------------------------------------------------------------
    Hi Radhika,
    Thanks for your help.

    setting ip address on SM1/1 throws this error:
    % IP addresses may not be configured on L2 links SM1/1.

    I have tried commands like: no switchport, no switchport mode trunk, no switchport mode access, no switchport trunk allowed vlan, and not success.

    Thanks,
    Herwind Garcia
    --
    To respond to this post, please click the following link:

    <http://developer.cisco.com/web/srev/forums/-/message_boards/view_message/3673432>

    or simply reply to this email.


    Subject: RE: New Message from Josip Zimet in Service Ready Engine Virtualization - T
    Replied by: Herwind garcia on 14-04-2011 06:58:58 PM
    Hi Radhika,

    I have configured interfaces sm1/0 and sm1/1, and installed sre-v software, but I can't reach hypervisor IP (20.0.0.2).
    My workstation is 10.240.141.123/25 and router is 10.70.0.3/26 (gigabitethernet 0/0.729)
    I can reach 10.70.0.10/26 (console manager) and from inside router (10.70.0.3/26) I can reach 10.240.141.123/25

    Why gigabitethernet 0/0.729? because I am not allowed to change this inside the organization. I just can use free IP's and configure SRE. I'm not the  network administrator.

    Interface SM1/1 seems to be  administratively down.

    Now, this is the script I followed to configure SM-SRE (by the way, I have installed HWIC module again) in order to have:
    Console manager (router side) IP: unnumbered (from gigabitethernet 0/0.729)
    Console manager IP: 10.70.0.10/26
    Hypervisor (router side) IP: 2.0.0.1/24
    Hypervisor IP: 2.0.0.2/24

    ==========================================

    -- Configure sm1/0
    configure terminal
    interface sm 1/0
    ip unnumbered gigabitethernet 0/0.729
    service-module ip address 10.70.0.10 255.255.255.192
    service-module ip default-gateway 10.70.0.3
    no shut
    exit
    ip route 10.70.0.10 255.255.255.255 SM1/0
    exit
    copy running-config startup-config
    show running-config

    -- Configure sm1/1
    configure terminal
    interface sm 1/1
    ip address 20.0.0.1 255.255.255.0
    service-module ip address 20.0.0.2 255.255.255.0
    end
    copy running-config startup-config
    service-module sm 1/0 reload

    -- Install sre-v software
    service-module sm 1/0 install url ftp://user:password@10.240.141.123/sre-v/sre-v-k9.smv.1.0.2.pkg

    -- Configure hypervisor dafeult gateway
    service-module sm 1/0 session
    hypervisor set ip default-gateway 20.0.0.1
    license activate sreVHost
    exit
    service-module sm 1/0 reload

    ==========================================

    Now, "show ip interfaces brief":
    Interface                  IP-Address      OK? Method Status                Protocol
    GigabitEthernet0/0         unassigned      YES NVRAM  up                    up     
    GigabitEthernet0/0.1       unassigned      YES unset  administratively down down   
    GigabitEthernet0/0.2       unassigned      YES unset  up                    up     
    GigabitEthernet0/0.7       10.11.0.1       YES NVRAM  administratively down down   
    GigabitEthernet0/0.300     unassigned      YES unset  administratively down down   
    GigabitEthernet0/0.729     10.70.0.3       YES NVRAM  up                    up     
    GigabitEthernet0/1         unassigned      YES NVRAM  up                    up     
    GigabitEthernet0/1.2       10.70.1.1       YES NVRAM  up                    up     
    GigabitEthernet0/2         unassigned      YES NVRAM  administratively down down   
    Serial0/1/0                unassigned      YES NVRAM  administratively down down   
    FastEthernet0/0/0          unassigned      YES unset  up                    down   
    FastEthernet0/0/1          unassigned      YES unset  up                    down   
    FastEthernet0/0/2          unassigned      YES unset  up                    down   
    FastEthernet0/0/3          unassigned      YES unset  down                  down   
    SM1/0                      10.70.0.3       YES TFTP   up                    up     
    SM1/1                      20.0.0.1        YES manual administratively down down   
    Loopback0                  10.5.4.2        YES NVRAM  up                    up     
    Tunnel0                    10.70.3.2       YES NVRAM  administratively down down   
    Tunnel1                    10.60.3.2       YES NVRAM  up                    up     
    Vlan1                      unassigned      YES NVRAM  up                    down   
    Vlan2                      unassigned      YES NVRAM  up                    down   
    Vlan7                      unassigned      YES NVRAM  up                    down  


    Is there any wrong?, am i missing something?

    Thanks in advance,
    Herwind garcia

    Subject: RE: New Message from Herwind garcia in Service Ready Engine Virtualization
    Replied by: Herwind garcia on 15-04-2011 01:41:46 PM
    Hi Radhika,

    It was a "no shut" command missing, thanks.

    Now, the router have only one patchcord connected to GigabitEthernet0/0 port. Do I need other patchcord connected directly to any sre module port in order to reach virtual machines or hypervisor on it?
     
    Thanks,
    Herwind Garcia
     
    Herwind,

    Can you manually issue ¿no shut¿ on the interface sm 1/1 and do a ¿write¿ on the router to save the config. I think the ¿no shut¿ step might be missing from the document.



    You may also need to add a route to reach the 20.0.0.2 network on your workstation. 



    Let me know if the above two steps don¿t work for you.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Thursday, April 14, 2011 3:59 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Herwind garcia in Service Ready Engine Virtualization - Technical Questions: RE: New Message from Josip Zimet in Service Ready Engine Virtualization - T



    Herwind garcia has created a new message in the forum "Technical Questions":

    --------------------------------------------------------------
    Hi Radhika,

    I have configured interfaces sm1/0 and sm1/1, and installed sre-v software, but I can't reach hypervisor IP (20.0.0.2).
    My workstation is 10.240.141.123/25 and router is 10.70.0.3/26 (gigabitethernet 0/0.729)
    I can reach 10.70.0.10/26 (console manager) and from inside router (10.70.0.3/26) I can reach 10.240.141.123/25

    Why gigabitethernet 0/0.729? because I am not allowed to change this inside the organization. I just can use free IP's and configure SRE. I'm not the network administrator.

    Interface SM1/1 seems to be administratively down.

    Now, this is the script I followed to configure SM-SRE (by the way, I have installed HWIC module again) in order to have:
    Console manager (router side) IP: unnumbered (from gigabitethernet 0/0.729)
    Console manager IP: 10.70.0.10/26
    Hypervisor (router side) IP: 2.0.0.1/24
    Hypervisor IP: 2.0.0.2/24

    ==========================================

    -- Configure sm1/0
    configure terminal
    interface sm 1/0
    ip unnumbered gigabitethernet 0/0.729
    service-module ip address 10.70.0.10 255.255.255.192
    service-module ip default-gateway 10.70.0.3
    no shut
    exit
    ip route 10.70.0.10 255.255.255.255 SM1/0
    exit
    copy running-config startup-config
    show running-config

    -- Configure sm1/1
    configure terminal
    interface sm 1/1
    ip address 20.0.0.1 255.255.255.0
    service-module ip address 20.0.0.2 255.255.255.0
    end
    copy running-config startup-config
    service-module sm 1/0 reload

    -- Install sre-v software
    service-module sm 1/0 install url ftp://user:password@10.240.141.123/sre-v/sre-v-k9.smv.1.0.2.pkg

    -- Configure hypervisor dafeult gateway
    service-module sm 1/0 session
    hypervisor set ip default-gateway 20.0.0.1
    license activate sreVHost
    exit
    service-module sm 1/0 reload

    ==========================================

    Now, "show ip interfaces brief":
    Interface IP-Address OK? Method Status Protocol
    GigabitEthernet0/0 unassigned YES NVRAM up up
    GigabitEthernet0/0.1 unassigned YES unset administratively down down
    GigabitEthernet0/0.2 unassigned YES unset up up
    GigabitEthernet0/0.7 10.11.0.1 YES NVRAM administratively down down
    GigabitEthernet0/0.300 unassigned YES unset administratively down down
    GigabitEthernet0/0.729 10.70.0.3 YES NVRAM up up
    GigabitEthernet0/1 unassigned YES NVRAM up up
    GigabitEthernet0/1.2 10.70.1.1 YES NVRAM up up
    GigabitEthernet0/2 unassigned YES NVRAM administratively down down
    Serial0/1/0 unassigned YES NVRAM administratively down down
    FastEthernet0/0/0 unassigned YES unset up down
    FastEthernet0/0/1 unassigned YES unset up down
    FastEthernet0/0/2 unassigned YES unset up down
    FastEthernet0/0/3 unassigned YES unset down down
    SM1/0 10.70.0.3 YES TFTP up up
    SM1/1 20.0.0.1 YES manual administratively down down
    Loopback0 10.5.4.2 YES NVRAM up up
    Tunnel0 10.70.3.2 YES NVRAM administratively down down
    Tunnel1 10.60.3.2 YES NVRAM up up
    Vlan1 unassigned YES NVRAM up down
    Vlan2 unassigned YES NVRAM up down
    Vlan7 unassigned YES NVRAM up down


    Is there any wrong?, am i missing something?

    Thanks in advance,
    Herwind garcia
    --
    To respond to this post, please click the following link:

    <http://developer.cisco.com/web/srev/forums/-/message_boards/view_message/3674522>

    or simply reply to this email.


    Subject: RE: New Message from Herwind garcia in Service Ready Engine Virtualization
    Replied by: Radhika Miriyala on 15-04-2011 04:59:25 PM
    Hi Herwind,

    It is not mandatory to have the front facing Ethernet port to be configured for the VMs or the Hypervisor. You should be able to connect to the hypervisor with the configuration you have so far.

    Please look at the following document http://www.cisco.com/en/US/prod/collateral/ps10265/ps11273/installation_guide_c07-640002.html#wp9000382 and chapter 6 and 7 which will walk you on how to configure the networking.

    Thanks,

    Radhika