Trouble installing SRE-V software

Version 1
    This document was generated from CDN thread

    Created by: Ken Romo on 20-11-2010 01:34:21 AM
    My config:
     
    interface SM1/0
     ip address 10.0.0.100 255.255.255.0
     service-module ip address 10.0.0.1 255.255.255.0
     service-module ip default-gateway 10.0.0.100
     service-module mgf ip address 1.10.10.5 255.255.255.0
     service-module mgf ip default-gateway 1.10.10.3
    !
    interface SM1/1
     description Internal switch interface connected to Service Module
     switchport mode trunk
    !
    interface Vlan1
     ip address 1.10.10.3 255.255.255.0
    !
    ip forward-protocol nd
    !
    ip http server
    ip http access-class 23
    ip http authentication local
    ip http secure-server
    ip http timeout-policy idle 60 life 86400 requests 10000
    !
    ip route 1.10.10.5 255.255.255.255 Vlan1
     
    Here is what I get when I try to install:
     
    Install of ftp://172.17.17.124/sre-v-k9.smv.1.0.0.35.pkg in progress
    Install status : File sre-v-k9.smv.1.0.0.35.pkg.install.sre requested
    Local Partition Info - (0 apps)
    =====================
      Retrieving partition information
    boxer#service-module sm 1/0 status
    Service Module is Cisco SM1/0
    Service Module supports session via TTY line 67
    Service Module is trying to recover from error
    Service Module heartbeat-reset is enabled
    Service Module is in fail open
    Service Module status is not available
    Module resource information:
      CPU Frequency: 1864 MHz
      Memory Size: 2535 MB
      Disk 0 Size: 500107 MB
      Disk 1 Size: 2055 MB
    Install of ftp://172.17.17.124/sre-v-k9.smv.1.0.0.35.pkg in progress
    Install status : File sre-v-k9.smv.1.0.0.35.pkg.install.sre requested
    Local Partition Info - (0 apps)
    =====================
      Retrieving partition information
    boxer#service-module sm 1/0 status
    Service Module is Cisco SM1/0
    Service Module supports session via TTY line 67
    Service Module is in Steady state
    Service Module heartbeat-reset is enabled
    Getting status from the Service Module, please wait..
    Cisco Foundation Software 1.0
    FNDN Running on SM
    Module resource information:
      CPU Frequency: 1862 MHz
      Memory Size: 4136636 MB
      Disk 0 Size: 953880 MB
    Install of ftp://172.17.17.124/sre-v-k9.smv.1.0.0.35.pkg in progress
    Install status : File sre-v-k9.smv.1.0.0.35.pkg.install.sre requested
    No local partition
    boxer#service-module sm 1/0 status
    Service Module is Cisco SM1/0
    Service Module supports session via TTY line 67
    Service Module is trying to recover from error
    Service Module heartbeat-reset is enabled
    Service Module status is not available
    Module resource information:
      CPU Frequency: 1862 MHz
      Memory Size: 4136636 MB
      Disk 0 Size: 953880 MB
    No install/uninstall in progress
    No local partition
     
    ---------------
     
    Any suggestons?

    Subject: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-
    Replied by: Ashwin Venkatesan on 20-11-2010 01:34:21 AM
    Hi Ken,



    After you issue the  install CLI  from IOS, Can you session into the blade to capture the installation steps/logs. Please make sure you have all required files in your ftp server.



    Thanks,

    Ashwin

    Subject: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-
    Replied by: Ken Romo on 20-11-2010 01:34:21 AM
    Ashwin,

    Here is what I get after the install command:




    boxer#term service-module sm 1/0 install url ftp://172.17.17.124/sre-v-k9.smv.1.0.0.35.pkg
    Proceed with installation? : y
    *Oct 26 19:56:58.283: %SM_INSTALL-6-INST_RSRC_GET: Getting resource information from SM1/0.
    *Oct 26 19:57:52.971: %SM_INSTALL-6-INST_RBIP: SM1/0 received msg: RBIP Registration Request
    Loading sre-v-k9.smv.1.0.0.35.pkg.install.sre !
    [OK - 1692/4096 bytes]
    Service module installation
    ios_version  15.1(2.18)T
    ios_image  c2900-universalk9-mz
    pkg_name  sre-v-k9.smv.1.0.0.35.pkg
    key_file  sre-v-k9.smv.1.0.0.35.key
    helper_file  sre-v-installer.smv.1.0.0.35
    Check target platform capabilities
    cpu   1865
    Resource check completed successfully. Proceeding to Install....
    boxer#
    boxer#
    boxer#
    *Oct 26 19:58:00.575: %SM_INSTALL-6-INST_RESET: SM1/0 is reset for software installation.
    *Oct 26 19:58:41.803: %SM_INSTALL-6-INST_RBIP: SM1/0 received msg: RBIP Registration Request
    *Oct 26 19:58:41.807: %SM_INSTALL-6-INST_RBIP: SM1/0 received msg: RBIP File Request
    *Oct 26 19:58:48.843: %SM_INSTALL-6-INST_RBIP: SM1/0 received msg: RBIP File Request
    *Oct 26 19:59:04.739: %SM_INSTALL-6-INST_RBIP: SM1/0 received msg: RBIP File Request
    *Oct 26 19:59:10.167: %SM_INSTALL-6-INST_RBIP: SM1/0 received msg: RBIP File Request
    *Oct 26 19:59:40.723: %SRE_SM-6-STATE_CHANGE: SM1/0 changing state from SERVICE_MODULE_STATE_ERRQ to SERVICE_MODULE_STATE_STDY
    *Oct 26 19:59:41.907: %SERVICEMODULE-2-IPCONFIGFAILED: Service module SM1/0 IP configuration (vlan default gateway) failed
    *Oct 26 20:00:23.287: %SM_INSTALL-6-INST_FAIL: SM1/0 is reset due to
     Can not download sre-v-k9.smv.1.0.0.35.pkg
    error code 0 : error type 'couldn't connect to host'.
    *Oct 26 20:00:23.287: %SRE_SM-6-STATE_CHANGE: SM1/0 changing state from SERVICE_MODULE_STATE_STDY to SERVICE_MODULE_STATE_ERRQ
    *Oct 26 20:00:23.287: %SM_INSTALL-6-INST_FAIL: SM1/0 is reset due to Unable to install. Please try again.

    Subject: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-
    Replied by: Michael Kinzlmaier on 20-11-2010 01:34:21 AM
    Hi Ken,



    Looks like you do not have routing setup so that the module can access the ftp server where the sre-v-k9.smv.1.0.0.35.pkg is located.

    The module needs to be able to reach the ftp server in order to download the pkg file.



    Mike

    Subject: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-
    Replied by: Ken Romo on 20-11-2010 01:34:24 AM
    Mike,
     
    My FTP server is on the same network as my ISR GigabitEthernet0/0 interface (172.17.17.124 255.255.248.0)
     
    Can you take a look at my configuration because I am still getting same errors?
     
    Thanks in advance,
     
    Ken
     
    ------------------
     
    interface GigabitEthernet0/0
     description To tusqa network
     ip address 172.17.17.130 255.255.248.0
     duplex auto
     speed auto
    !
    interface SM1/0
     ip unnumbered GigabitEthernet0/0
     service-module fail-open
     service-module ip address 172.17.17.129 255.255.248.0
     service-module ip default-gateway 172.17.17.130
     service-module mgf ip address 10.62.64.1 255.255.255.0
     service-module mgf ip default-gateway 10.62.64.2
    !
    interface SM1/1
     description Internal switch interface connected to Service Module
     switchport mode trunk
    !
    interface Vlan1
     ip address 10.62.64.2 255.255.255.0
    !
    ip forward-protocol nd
    !
    ip http server
    ip http access-class 23
    ip http authentication local
    ip http secure-server
    ip http timeout-policy idle 60 life 86400 requests 10000
    !
    ip route 10.62.63.3 255.255.255.255 SM1/0
    ip route 10.62.64.1 255.255.255.255 Vlan1
    ip route 10.62.64.2 255.255.255.255 10.62.64.1
    ip route 172.17.17.130 255.255.255.255 SM1/0
    ip route 172.17.17.130 255.255.255.255 Vlan1
    ip route 172.17.17.130 255.255.255.255 172.17.17.124
    ip route 172.17.17.130 255.255.255.255 172.17.17.0

    Subject: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-
    Replied by: Radhika Miriyala on 20-11-2010 01:34:25 AM
    Ken,

    I think there is a mistake in your ip route for the sm 1/0

    It should be¿ ip route 172.17.17.129 255.255.255.255 SM1/0 ¿ The router should point to the ip address assigned to service-module ip address ¿x.x.x.x¿

    Thanks,

    Radhika

    Subject: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-
    Replied by: Michael Kinzlmaier on 20-11-2010 01:34:25 AM
    Hi Ken,





    You need to add the following to your config:



    ip route 172.17.17.129 255.255.255.255 SM1/0



    Mike









    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Wednesday, October 27, 2010 4:00 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Mike,

    My FTP server is on the same network as my ISR GigabitEthernet0/0 interface (172.17.17.124 255.255.248.0)

    Can you take a look at my configuration because I am still getting same errors?

    Thanks in advance,

    Ken

    ------------------

    interface GigabitEthernet0/0
    description To tusqa network
    ip address 172.17.17.130 255.255.248.0
    duplex auto
    speed auto
    !
    interface SM1/0
    ip unnumbered GigabitEthernet0/0
    service-module fail-open
    service-module ip address 172.17.17.129 255.255.248.0
    service-module ip default-gateway 172.17.17.130
    service-module mgf ip address 10.62.64.1 255.255.255.0
    service-module mgf ip default-gateway 10.62.64.2
    !
    interface SM1/1
    description Internal switch interface connected to Service Module
    switchport mode trunk
    !
    interface Vlan1
    ip address 10.62.64.2 255.255.255.0
    !
    ip forward-protocol nd
    !
    ip http server
    ip http access-class 23
    ip http authentication local
    ip http secure-server
    ip http timeout-policy idle 60 life 86400 requests 10000
    !
    ip route 10.62.63.3 255.255.255.255 SM1/0
    ip route 10.62.64.1 255.255.255.255 Vlan1
    ip route 10.62.64.2 255.255.255.255 10.62.64.1
    ip route 172.17.17.130 255.255.255.255 SM1/0
    ip route 172.17.17.130 255.255.255.255 Vlan1
    ip route 172.17.17.130 255.255.255.255 172.17.17.124
    ip route 172.17.17.130 255.255.255.255 172.17.17.0


    Hi Ken,



    Looks like you do not have routing setup so that the module can access the ftp server where the sre-v-k9.smv.1.0.0.35.pkg is located.

    The module needs to be able to reach the ftp server in order to download the pkg file.



    Mike







    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Tuesday, October 26, 2010 4:20 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Ashwin,

    Here is what I get after the install command:




    boxer#term service-module sm 1/0 install url ftp://172.17.17.124/sre-v-k9.smv.1.0.0.35.pkg
    Proceed with installation? : y
    *Oct 26 19:56:58.283: %SM_INSTALL-6-INST_RSRC_GET: Getting resource information from SM1/0.
    *Oct 26 19:57:52.971: %SM_INSTALL-6-INST_RBIP: SM1/0 received msg: RBIP Registration Request
    Loading sre-v-k9.smv.1.0.0.35.pkg.install.sre !
    [OK - 1692/4096 bytes]
    Service module installation
    ios_version 15.1(2.18)T
    ios_image c2900-universalk9-mz
    pkg_name sre-v-k9.smv.1.0.0.35.pkg
    key_file sre-v-k9.smv.1.0.0.35.key
    helper_file sre-v-installer.smv.1.0.0.35
    Check target platform capabilities
    cpu 1865
    Resource check completed successfully. Proceeding to Install....
    boxer#
    boxer#
    boxer#
    *Oct 26 19:58:00.575: %SM_INSTALL-6-INST_RESET: SM1/0 is reset for software installation.
    *Oct 26 19:58:41.803: %SM_INSTALL-6-INST_RBIP: SM1/0 received msg: RBIP Registration Request
    *Oct 26 19:58:41.807: %SM_INSTALL-6-INST_RBIP: SM1/0 received msg: RBIP File Request
    *Oct 26 19:58:48.843: %SM_INSTALL-6-INST_RBIP: SM1/0 received msg: RBIP File Request
    *Oct 26 19:59:04.739: %SM_INSTALL-6-INST_RBIP: SM1/0 received msg: RBIP File Request
    *Oct 26 19:59:10.167: %SM_INSTALL-6-INST_RBIP: SM1/0 received msg: RBIP File Request
    *Oct 26 19:59:40.723: %SRE_SM-6-STATE_CHANGE: SM1/0 changing state from SERVICE_MODULE_STATE_ERRQ to SERVICE_MODULE_STATE_STDY
    *Oct 26 19:59:41.907: %SERVICEMODULE-2-IPCONFIGFAILED: Service module SM1/0 IP configuration (vlan default gateway) failed
    *Oct 26 20:00:23.287: %SM_INSTALL-6-INST_FAIL: SM1/0 is reset due to
    Can not download sre-v-k9.smv.1.0.0.35.pkg
    error code 0 : error type 'couldn't connect to host'.
    *Oct 26 20:00:23.287: %SRE_SM-6-STATE_CHANGE: SM1/0 changing state from SERVICE_MODULE_STATE_STDY to SERVICE_MODULE_STATE_ERRQ
    *Oct 26 20:00:23.287: %SM_INSTALL-6-INST_FAIL: SM1/0 is reset due to Unable to install. Please try again.


    Hi Ken,



    After you issue the install CLI from IOS, Can you session into the blade to capture the installation steps/logs. Please make sure you have all required files in your ftp server.



    Thanks,

    Ashwin



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Monday, October 25, 2010 5:18 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: Trouble installing SRE-V software



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    My config:

    interface SM1/0
    ip address 10.0.0.100 255.255.255.0
    service-module ip address 10.0.0.1 255.255.255.0
    service-module ip default-gateway 10.0.0.100
    service-module mgf ip address 1.10.10.5 255.255.255.0
    service-module mgf ip default-gateway 1.10.10.3
    !
    interface SM1/1
    description Internal switch interface connected to Service Module
    switchport mode trunk
    !
    interface Vlan1
    ip address 1.10.10.3 255.255.255.0
    !
    ip forward-protocol nd
    !
    ip http server
    ip http access-class 23
    ip http authentication local
    ip http secure-server
    ip http timeout-policy idle 60 life 86400 requests 10000
    !
    ip route 1.10.10.5 255.255.255.255 Vlan1

    Here is what I get when I try to install:

    Install of ftp://172.17.17.124/sre-v-k9.smv.1.0.0.35.pkg in progress
    Install status : File sre-v-k9.smv.1.0.0.35.pkg.install.sre requested
    Local Partition Info - (0 apps)
    =====================
    Retrieving partition information
    boxer#service-module sm 1/0 status
    Service Module is Cisco SM1/0
    Service Module supports session via TTY line 67
    Service Module is trying to recover from error
    Service Module heartbeat-reset is enabled
    Service Module is in fail open
    Service Module status is not available
    Module resource information:
    CPU Frequency: 1864 MHz
    Memory Size: 2535 MB
    Disk 0 Size: 500107 MB
    Disk 1 Size: 2055 MB
    Install of ftp://172.17.17.124/sre-v-k9.smv.1.0.0.35.pkg in progress
    Install status : File sre-v-k9.smv.1.0.0.35.pkg.install.sre requested
    Local Partition Info - (0 apps)
    =====================
    Retrieving partition information
    boxer#service-module sm 1/0 status
    Service Module is Cisco SM1/0
    Service Module supports session via TTY line 67
    Service Module is in Steady state
    Service Module heartbeat-reset is enabled
    Getting status from the Service Module, please wait..
    Cisco Foundation Software 1.0
    FNDN Running on SM
    Module resource information:
    CPU Frequency: 1862 MHz
    Memory Size: 4136636 MB
    Disk 0 Size: 953880 MB
    Install of ftp://172.17.17.124/sre-v-k9.smv.1.0.0.35.pkg in progress
    Install status : File sre-v-k9.smv.1.0.0.35.pkg.install.sre requested
    No local partition
    boxer#service-module sm 1/0 status
    Service Module is Cisco SM1/0
    Service Module supports session via TTY line 67
    Service Module is trying to recover from error
    Service Module heartbeat-reset is enabled
    Service Module status is not available
    Module resource information:
    CPU Frequency: 1862 MHz
    Memory Size: 4136636 MB
    Disk 0 Size: 953880 MB
    No install/uninstall in progress
    No local partition

    ---------------

    Any suggestons?
    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2678543>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2681319>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2688556>
    or simply reply to this email.

    Subject: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-
    Replied by: Ken Romo on 20-11-2010 01:34:25 AM
    Radhika,
     
    That was exactly it thank you.
    Now that I have SRE-V software loaded I am trying to install vSphere Client
     
     

    Go to https://ip address of the MGF interface
     
    but I cannot ping the MGF interface (10.62.64.1) from outside the router any suggestions?

    Current config:

    interface GigabitEthernet0/0
     description To tusqa network
     ip address 172.17.17.130 255.255.248.0
     
    interface SM1/0
     ip unnumbered GigabitEthernet0/0
     service-module ip address 172.17.17.129 255.255.248.0
     !Application: SRE-V Running on SMV
     service-module ip default-gateway 172.17.17.130
     service-module mgf ip address 10.62.64.1 255.255.255.0
     service-module mgf ip default-gateway 10.62.64.2
    !
    interface SM1/1
     description Internal switch interface connected to Service Module
     switchport mode trunk
    !
    interface Vlan1
     ip address 10.62.64.2 255.255.255.0
    !
    ip forward-protocol nd
    !
    ip http server
    ip http access-class 23
    ip http authentication local
    ip http secure-server
    ip http timeout-policy idle 60 life 86400 requests 10000
    !
    ip route 10.62.64.1 255.255.255.255 Vlan1
    ip route 10.62.64.2 255.255.255.255 10.62.64.1
    ip route 172.17.17.129 255.255.255.255 SM1/0
    ip route 172.17.17.130 255.255.255.255 SM1/0
    ip route 172.17.17.130 255.255.255.255 Vlan1
    ip route 172.17.17.130 255.255.255.255 172.17.17.124
    ip route 172.17.17.130 255.255.255.255 172.17.17.0

    Subject: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-
    Replied by: Radhika Miriyala on 20-11-2010 01:34:25 AM
    Ken,

    Is the 10.62.64.0 network a private network to you router?  What network is the PC you are trying to connect from?

    If the 10.62.64.0 is a private network just in your router and you PC is in the 172.17.17.x network. Than you might need to add a route into your pc to point 10.62.64.0.x to your router gige Ip address.

    Thanks,

    Radhika

    Subject: RE: New Message from Radhika Miriyala in Service Ready Engine Virtualizatio
    Replied by: Michael Kinzlmaier on 20-11-2010 01:34:25 AM
    Hi Ken,



    Did you activate the evaluation license on the module ?

    ( i.e. ' license activate sreVHost' )

    You will not be able to ping the mgf ip address until you do that.

    Also why do you have the following in your config ?

    ip route 10.62.64.2 255.255.255.255 10.62.64.1

    I don't think the above route needs to be there, can you remove it and try to ping the mgf ip from the router console after making sure that license is activated.

    Mike

    Subject: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-
    Replied by: Ken Romo on 20-11-2010 01:34:26 AM
    Radhika,
     
    I added the route to my pc and now I can ping the vlan 10.62.64.2 but not the mgf interface 10.62.64.1
     
    any suggestions?
     
    Ken

    Subject: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-
    Replied by: Michael Kinzlmaier on 20-11-2010 01:34:26 AM
    Ken,



    Can you go to the SRE module CLI and execute the following:

    show license in-use

    If you don't see any output that means you do not have a license enabled and IP connectivity to the mgf ip will be blocked.

    Mike

    Subject: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-
    Replied by: Ken Romo on 20-11-2010 01:34:26 AM
    Mike,

    Looks like the license is good however as you can see below when I am sessioned in on the module I can't ping the mgf interface from thier either, should I be able to (i can ping the mgf interface for the 0/0 gigaethernet interface)?

    -----------------------------

    se-172-17-17-129# sho license in-use
    StoreIndex:  0  Feature: SRE-V-HOST-LIC                    Version: 1.0
            License Type: Evaluation
            License State: Active, In Use
                Evaluation total period:  8 weeks  4 days
                Evaluation period left:  8 weeks  2 days
                Expiry date: Fri Feb 29 18:30:10 2008
            License Count: Non-Counted
            License Priority: Low
    se-172-17-17-129#

    se-172-17-17-129# ping 10.62.64.2   (ping to VLAN1 good)
    PING 10.62.64.2 (10.62.64.2) 56(84) bytes of data.
    64 bytes from 10.62.64.2: icmp_seq=1 ttl=255 time=0.660 ms
    64 bytes from 10.62.64.2: icmp_seq=2 ttl=255 time=0.763 ms
    64 bytes from 10.62.64.2: icmp_seq=3 ttl=255 time=0.221 ms
    64 bytes from 10.62.64.2: icmp_seq=4 ttl=255 time=0.464 ms
    64 bytes from 10.62.64.2: icmp_seq=5 ttl=255 time=0.209 ms
    --- 10.62.64.2 ping statistics ---
    5 packets transmitted, 5 received, 0% packet loss, time 5ms
    rtt min/avg/max/mdev = 0.209/0.463/0.763/0.225 ms, ipg/ewma 1.297/0.549 ms
    se-172-17-17-129# ping 10.62.64.1
    PING 10.62.64.1 (10.62.64.1) 56(84) bytes of data. (ping to mgf interface not good)
    --- 10.62.64.1 ping statistics ---
    5 packets transmitted, 0 received, 100% packet loss, time 4000ms
    , ipg/ewma 1000.200/0.000 ms

    Subject: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-
    Replied by: Radhika Miriyala on 20-11-2010 01:34:26 AM
    Ken,

    In Normal conditions you should be able to ping.  Can you send us the output of 'show hypervisor ip' and 'show hypervisor nics'

    Thanks,

    Radhika

    Subject: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-
    Replied by: Ken Romo on 20-11-2010 01:34:26 AM
    Radhika,
     
    Here are the ip's and nics for the hypervisor, I noticed there was no Default Gateway so I added the VLAN1 as the gateway and i was then able to ping the mgf interface from within the mocule session however check this out when I go to my PC I ping the mgf interface and it pings twice (%50 loss) then it REBOOTS THE ROUTER!
     
    what do you think?
     
    se-172-17-17-129# show hypervisor ip
    Hostname:               localhost
    Domain Name:            None
    IP Config:              10.62.64.1(Subnet Mask: 255.255.255.0)
                            169.254.1.1(Subnet Mask: 255.255.255.0)
    Default Gateway:        None
    Preferred DNS Server:   None
    Alternative DNS Server: None
     
     
    se-172-17-17-129# show hypervisor nics
    Name    PCI           Driver      Link Speed     Duplex MAC Address       MTU
    vmnic0  0000:01:00.00 e1000e      Down 0Mbps     Half   00:23:eb:a1:12:1e 1500
    vmnic1  0000:02:00.00 bnx2        Up   1000Mbps  Full   68:ef:bd:f9:33:01 1500
    vmnic2  0000:02:00.01 bnx2        Up   1000Mbps  Full   68:ef:bd:f9:33:00 1500
    3 total nics

    Subject: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-
    Replied by: Radhika Miriyala on 20-11-2010 01:34:26 AM
    Rebooting the router?? Is very strange. Do you have any console messages on the router?



    The ping was failing because the default gateway was missing.  But we need to figure out why the router rebooted/ Do you have any tracebacks on the router? (IOS image also is a beta Image so could be a issue there) Do you have any other modules on this router?

    Thanks,

    Radhika

    Subject: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-
    Replied by: Ken Romo on 20-11-2010 01:34:26 AM
    Rebooting the router?? Is very strange. Do you have any console messages on the router?

    Yes see below:

    The ping was failing because the default gateway was missing. But we need to figure out why the router rebooted/ Do you have any tracebacks on the router?
     
    Yes see below:
     
    (IOS image also is a beta Image so could be a issue there) Do you have any other modules on this router?
     
    No other modules on the router.
     
    ------------------------
    %ALIGN-1-FATAL: Illegal access to a low address 19:09:57 UTC Thu Oct 28 2010
     addr=0x14, pc=0x22765BD8z , ra=0x22765B84z , sp=0x300A5EB8
    %ALIGN-1-FATAL: Illegal access to a low address 19:09:57 UTC Thu Oct 28 2010
     addr=0x14, pc=0x22765BD8z , ra=0x22765B84z , sp=0x300A5EB8

     19:09:57 UTC Thu Oct 28 2010: TLB (store) exception, CPU signal 10, PC = 0x22774218
     
    --------------------------------------------------------------------
       Possible software fault. Upon reccurence, please collect
       crashinfo, "show tech" and contact Cisco Technical Support.
    --------------------------------------------------------------------

    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x21A48954z
    $0 : 00000000 00000000, AT : 00000000 29130000, v0 : 00000000 00000001, v1 : 00000000 0D8BFDC0
    a0 : 00000000 00000000, a1 : 00000000 0D8BFE04, a2 : 00000000 2A30483C, a3 : 00000000 00000004
    t0 : 00000000 00000020, t1 : 00000000 500099E1, t2 : 00000000 500081E0, t3 : FFFFFFFF FFFFFFF2
    t4 : 00000000 0000000E, t5 : 00000000 00000000, t6 : 00000000 0D8FE810, t7 : 00000000 000001FF
    s0 : 00000000 00000000, s1 : 00000000 2A3098C0, s2 : FFFFFFFF FFFFFFEC, s3 : 00000000 30F183E0
    s4 : 00000000 0D8FE81E, s5 : 00000000 2A30CC60, s6 : 00000000 00000000, s7 : 00000000 0000000E
    t8 : 00000000 000007FC, t9 : 00000000 2A30BF80, k0 : 00000000 00000000, k1 : 00000000 00000000
    gp : 00000000 2913F9A0, sp : 00000000 300A5EB8, s8 : 00000000 0000003C, ra : 00000000 227741C4
    EPC  : 22774218, ErrorEPC : 80412AC4, SREG     : 500099E3
    MDLO : 83A9196A, MDHI     : E9785555, BadVaddr : 00000014
    CacheErr_Icache : 0x007F7F00 - 000040D8, CacheErr_Dcache : 0x00000000 - 00003640
    TagLo_Icache : 0x00000000 - 2364C303, DataLo_Icache : 0x14A400C5 - 26420004
    DataHi_Icache: 0x00000000 - 00000001
    TagLo_Dcache : 0x00000000 - 300A6103, TagHi_Dcache : 0x00000000 - 09137B01
    DataLo_Dcache: 0x11C00011 - AE380008, DataHi_Dcache : 0x00000000 - 0000000D
    TEXT_START : 0x2100EF18
    DATA_START : 0x26094640
    Cause 0000040C (Code 0x3): TLB (store) exception

     19:09:57 UTC Thu Oct 28 2010: TLB (store) exception, CPU signal 10, PC = 0x22774218
     
    --------------------------------------------------------------------
       Possible software fault. Upon reccurence, please collect
       crashinfo, "show tech" and contact Cisco Technical Support.
    --------------------------------------------------------------------

    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x21A48954z
    $0 : 00000000 00000000, AT : 00000000 29130000, v0 : 00000000 00000001, v1 : 00000000 0D8BFDC0
    a0 : 00000000 00000000, a1 : 00000000 0D8BFE04, a2 : 00000000 2A30483C, a3 : 00000000 00000004
    t0 : 00000000 00000020, t1 : 00000000 500099E1, t2 : 00000000 500081E0, t3 : FFFFFFFF FFFFFFF2
    t4 : 00000000 0000000E, t5 : 00000000 00000000, t6 : 00000000 0D8FE810, t7 : 00000000 000001FF
    s0 : 00000000 00000000, s1 : 00000000 2A3098C0, s2 : FFFFFFFF FFFFFFEC, s3 : 00000000 30F183E0
    s4 : 00000000 0D8FE81E, s5 : 00000000 2A30CC60, s6 : 00000000 00000000, s7 : 00000000 0000000E
    t8 : 00000000 000007FC, t9 : 00000000 2A30BF80, k0 : 00000000 00000000, k1 : 00000000 00000000
    gp : 00000000 2913F9A0, sp : 00000000 300A5EB8, s8 : 00000000 0000003C, ra : 00000000 227741C4
    EPC  : 22774218, ErrorEPC : 80412AC4, SREG     : 500099E3
    MDLO : 83A9196A, MDHI     : E9785555, BadVaddr : 00000014
    CacheErr_Icache : 0x007F7F00 - 000040D8, CacheErr_Dcache : 0x00000000 - 00003640
    TagLo_Icache : 0x00000000 - 2364C303, DataLo_Icache : 0x14A400C5 - 26420004
    DataHi_Icache: 0x00000000 - 00000001
    TagLo_Dcache : 0x00000000 - 300A6103, TagHi_Dcache : 0x00000000 - 09137B01
    DataLo_Dcache: 0x11C00011 - AE380008, DataHi_Dcache : 0x00000000 - 0000000D
    TEXT_START : 0x2100EF18
    DATA_START : 0x26094640
    Cause 0000040C (Code 0x3): TLB (store) exception
    Writing crashinfo to flash:crashinfo_20101028-190957-UTC
     19:09:57 UTC Thu Oct 28 2010: TLB (store) exception, CPU signal 10, PC = 0x22774218
     
    --------------------------------------------------------------------
       Possible software fault. Upon reccurence, please collect
       crashinfo, "show tech" and contact Cisco Technical Support.
    --------------------------------------------------------------------

    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x21A48954z
    $0 : 00000000 00000000, AT : 00000000 29130000, v0 : 00000000 00000001, v1 : 00000000 0D8BFDC0
    a0 : 00000000 00000000, a1 : 00000000 0D8BFE04, a2 : 00000000 2A30483C, a3 : 00000000 00000004
    t0 : 00000000 00000020, t1 : 00000000 500099E1, t2 : 00000000 500081E0, t3 : FFFFFFFF FFFFFFF2
    t4 : 00000000 0000000E, t5 : 00000000 00000000, t6 : 00000000 0D8FE810, t7 : 00000000 000001FF
    s0 : 00000000 00000000, s1 : 00000000 2A3098C0, s2 : FFFFFFFF FFFFFFEC, s3 : 00000000 30F183E0
    s4 : 00000000 0D8FE81E, s5 : 00000000 2A30CC60, s6 : 00000000 00000000, s7 : 00000000 0000000E
    t8 : 00000000 000007FC, t9 : 00000000 2A30BF80, k0 : 00000000 00000000, k1 : 00000000 00000000
    gp : 00000000 2913F9A0, sp : 00000000 300A5EB8, s8 : 00000000 0000003C, ra : 00000000 227741C4
    EPC  : 22774218, ErrorEPC : 80412AC4, SREG     : 500099E3
    MDLO : 83A9196A, MDHI     : E9785555, BadVaddr : 00000014
    CacheErr_Icache : 0x007F7F00 - 000040D8, CacheErr_Dcache : 0x00000000 - 00003640
    TagLo_Icache : 0x00000000 - 2364C303, DataLo_Icache : 0x14A400C5 - 26420004
    DataHi_Icache: 0x00000000 - 00000001
    TagLo_Dcache : 0x00000000 - 300A6103, TagHi_Dcache : 0x00000000 - 09137B01
    DataLo_Dcache: 0x11C00011 - AE380008, DataHi_Dcache : 0x00000000 - 0000000D
    TEXT_START : 0x2100EF18
    DATA_START : 0x26094640
    Cause 0000040C (Code 0x3): TLB (store) exception
    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x21A48954z

    === Flushing messages (19:09:58 UTC Thu Oct 28 2010) ===
    Buffered messages:
    *Oct 28 18:11:15.071: %LINK-3-UPDOWN: Interface SM1/0, changed state to up
    *Oct 28 18:11:17.191: %LINK-3-UPDOWN: Interface GigabitEthernet0/0, changed state to up
    *Oct 28 18:11:17.191: %LINK-3-UPDOWN: Interface GigabitEthernet0/1, changed state to down
    *Oct 28 18:11:17.191: %LINK-3-UPDOWN: Interface GigabitEthernet0/2, changed state to down
    *Oct 28 18:11:19.635: %LINK-3-UPDOWN: Interface SM1/1, changed state to up
    *Oct 28 18:11:36.743: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/0, changed state to up
    *Oct 28 18:11:37.007: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/1, changed state to up
    *Oct 28 18:11:37.159: %LINK-3-UPDOWN: Interface Foreign Exchange Station 0/1/0, changed state to up
    *Oct 28 18:11:37.159: %LINK-3-UPDOWN: Interface Foreign Exchange Station 0/1/1, changed state to up
    *Oct 28 18:12:18.739: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/0, changed state to operational status down due to cable removal
    *Oct 28 18:12:19.739: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/1, changed state to operational status down due to cable removal
    Queued messages:
    No warm reboot Storage
    *** System received a Bus Error exception ***
    signal= 0xa, code= 0x40c, context= 0x29732914
      PC = 0x22774218, SP = 0x300a5eb8, RA = 0x227741c4
      Cause Reg = 0x0000040c, Status Reg = 0x500099e3
    System Bootstrap, Version 15.0(1r)M6, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 2010 by cisco Systems, Inc.
    Total memory size = 512 MB - On-board = 512 MB, DIMM0 = 0 MB
    CISCO2911/K9 platform with 524288 Kbytes of main memory
    Main memory is configured to 72/-1(On-board/DIMM0) bit mode with ECC enabled

    Readonly ROMMON initialized
    program load complete, entry point: 0x80803000, size: 0x1b340

    IOS Image Load Test
    ___________________
    Digitally Signed Development Software
    program load complete, entry point: 0x81000000, size: 0x40b6b74
    Self decompressing the image : #################################################

    Subject: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-
    Replied by: Radhika Miriyala on 20-11-2010 01:34:27 AM
    Thanks Ken. We will take a look at the tracebacks to see what is happening on the IOS end.

    Once the router is booted up is the module up and running? Is the ping to mgf working?

    Thanks,

    Radhika

    Subject: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-
    Replied by: Ken Romo on 20-11-2010 01:34:27 AM
    Thanks Ken. We will take a look at the tracebacks to see what is happening on the IOS end.

    Once the router is booted up is the module up and running?
     
    Yes
     
    Is the ping to mgf working?

    Internally yes, when I ping from my PC that is when it reboots (it is repeatable).
     
    Ken
    ---------------

    Subject: RE: New Message from Radhika Miriyala in Service Ready Engine Virtualizatio
    Replied by: Radhika Miriyala on 20-11-2010 01:34:27 AM
    Ken,

    I was looking at your config s sent some time back and you have ip routes to Vlan 1 . Can you please remove the two lines below and try.

    ip route 10.62.64.1 255.255.255.255 Vlan1
    ip route 172.17.17.130 255.255.255.255 Vlan1

    Thanks,

    Radhika

    Subject: RE: New Message from Radhika Miriyala in Service Ready Engine Virtualizatio
    Replied by: Ken Romo on 20-11-2010 01:34:27 AM
    Here is current config, what woud you suggest I change?
     
     
    interface GigabitEthernet0/0
     description To tusqa network
     ip address 172.17.17.130 255.255.248.0
     !
    interface SM1/0
     ip unnumbered GigabitEthernet0/0
     service-module ip address 172.17.17.129 255.255.248.0
     !Application: SRE-V Running on SMV
     service-module ip default-gateway 172.17.17.130
     service-module mgf ip address 10.62.64.1 255.255.255.0
     service-module mgf ip default-gateway 10.62.64.2
    !
    interface SM1/1
     description Internal switch interface connected to Service Module
     switchport mode trunk
    !
    interface Vlan1
     ip address 10.62.64.2 255.255.255.0
    !
    ip forward-protocol nd
    !
    ip http server
    ip http access-class 23
    ip http authentication local
    ip http secure-server
    ip http timeout-policy idle 60 life 86400 requests 10000
    !
    ip route 10.62.64.1 255.255.255.255 Vlan1
    ip route 172.17.17.129 255.255.255.255 SM1/0

    Subject: RE: New Message from Radhika Miriyala in Service Ready Engine Virtualizatio
    Replied by: Michael Kinzlmaier on 20-11-2010 01:34:30 AM
    Hi Ken,



    In addition please remove the following from the IOS config:



    ip route 10.62.64.2 255.255.255.255 10.62.64.1





    Mike





    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Thursday, October 28, 2010 3:55 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Radhika Miriyala in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Radhika Miriyala in Service Ready Engine Virtualizatio



    Radhika Miriyala has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Ken,

    I was looking at your config s sent some time back and you have ip routes to Vlan 1 . Can you please remove the two lines below and try.

    ip route 10.62.64.1 255.255.255.255 Vlan1
    ip route 172.17.17.130 255.255.255.255 Vlan1



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Thursday, October 28, 2010 12:30 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Radhika Miriyala in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Radhika Miriyala has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Thanks Ken. We will take a look at the tracebacks to see what is happening on the IOS end.



    Once the router is booted up is the module up and running? Is the ping to mgf working?



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Thursday, October 28, 2010 12:25 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Rebooting the router?? Is very strange. Do you have any console messages on the router?

    Yes see below:

    The ping was failing because the default gateway was missing. But we need to figure out why the router rebooted/ Do you have any tracebacks on the router?

    Yes see below:

    (IOS image also is a beta Image so could be a issue there) Do you have any other modules on this router?

    No other modules on the router.

    ------------------------
    %ALIGN-1-FATAL: Illegal access to a low address 19:09:57 UTC Thu Oct 28 2010
    addr=0x14, pc=0x22765BD8z , ra=0x22765B84z , sp=0x300A5EB8
    %ALIGN-1-FATAL: Illegal access to a low address 19:09:57 UTC Thu Oct 28 2010
    addr=0x14, pc=0x22765BD8z , ra=0x22765B84z , sp=0x300A5EB8

    19:09:57 UTC Thu Oct 28 2010: TLB (store) exception, CPU signal 10, PC = 0x22774218

    --------------------------------------------------------------------
    Possible software fault. Upon reccurence, please collect
    crashinfo, "show tech" and contact Cisco Technical Support.
    --------------------------------------------------------------------

    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x21A48954z
    $0 : 00000000 00000000, AT : 00000000 29130000, v0 : 00000000 00000001, v1 : 00000000 0D8BFDC0
    a0 : 00000000 00000000, a1 : 00000000 0D8BFE04, a2 : 00000000 2A30483C, a3 : 00000000 00000004
    t0 : 00000000 00000020, t1 : 00000000 500099E1, t2 : 00000000 500081E0, t3 : FFFFFFFF FFFFFFF2
    t4 : 00000000 0000000E, t5 : 00000000 00000000, t6 : 00000000 0D8FE810, t7 : 00000000 000001FF
    s0 : 00000000 00000000, s1 : 00000000 2A3098C0, s2 : FFFFFFFF FFFFFFEC, s3 : 00000000 30F183E0
    s4 : 00000000 0D8FE81E, s5 : 00000000 2A30CC60, s6 : 00000000 00000000, s7 : 00000000 0000000E
    t8 : 00000000 000007FC, t9 : 00000000 2A30BF80, k0 : 00000000 00000000, k1 : 00000000 00000000
    gp : 00000000 2913F9A0, sp : 00000000 300A5EB8, s8 : 00000000 0000003C, ra : 00000000 227741C4
    EPC : 22774218, ErrorEPC : 80412AC4, SREG : 500099E3
    MDLO : 83A9196A, MDHI : E9785555, BadVaddr : 00000014
    CacheErr_Icache : 0x007F7F00 - 000040D8, CacheErr_Dcache : 0x00000000 - 00003640
    TagLo_Icache : 0x00000000 - 2364C303, DataLo_Icache : 0x14A400C5 - 26420004
    DataHi_Icache: 0x00000000 - 00000001
    TagLo_Dcache : 0x00000000 - 300A6103, TagHi_Dcache : 0x00000000 - 09137B01
    DataLo_Dcache: 0x11C00011 - AE380008, DataHi_Dcache : 0x00000000 - 0000000D
    TEXT_START : 0x2100EF18
    DATA_START : 0x26094640
    Cause 0000040C (Code 0x3): TLB (store) exception

    19:09:57 UTC Thu Oct 28 2010: TLB (store) exception, CPU signal 10, PC = 0x22774218

    --------------------------------------------------------------------
    Possible software fault. Upon reccurence, please collect
    crashinfo, "show tech" and contact Cisco Technical Support.
    --------------------------------------------------------------------

    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x21A48954z
    $0 : 00000000 00000000, AT : 00000000 29130000, v0 : 00000000 00000001, v1 : 00000000 0D8BFDC0
    a0 : 00000000 00000000, a1 : 00000000 0D8BFE04, a2 : 00000000 2A30483C, a3 : 00000000 00000004
    t0 : 00000000 00000020, t1 : 00000000 500099E1, t2 : 00000000 500081E0, t3 : FFFFFFFF FFFFFFF2
    t4 : 00000000 0000000E, t5 : 00000000 00000000, t6 : 00000000 0D8FE810, t7 : 00000000 000001FF
    s0 : 00000000 00000000, s1 : 00000000 2A3098C0, s2 : FFFFFFFF FFFFFFEC, s3 : 00000000 30F183E0
    s4 : 00000000 0D8FE81E, s5 : 00000000 2A30CC60, s6 : 00000000 00000000, s7 : 00000000 0000000E
    t8 : 00000000 000007FC, t9 : 00000000 2A30BF80, k0 : 00000000 00000000, k1 : 00000000 00000000
    gp : 00000000 2913F9A0, sp : 00000000 300A5EB8, s8 : 00000000 0000003C, ra : 00000000 227741C4
    EPC : 22774218, ErrorEPC : 80412AC4, SREG : 500099E3
    MDLO : 83A9196A, MDHI : E9785555, BadVaddr : 00000014
    CacheErr_Icache : 0x007F7F00 - 000040D8, CacheErr_Dcache : 0x00000000 - 00003640
    TagLo_Icache : 0x00000000 - 2364C303, DataLo_Icache : 0x14A400C5 - 26420004
    DataHi_Icache: 0x00000000 - 00000001
    TagLo_Dcache : 0x00000000 - 300A6103, TagHi_Dcache : 0x00000000 - 09137B01
    DataLo_Dcache: 0x11C00011 - AE380008, DataHi_Dcache : 0x00000000 - 0000000D
    TEXT_START : 0x2100EF18
    DATA_START : 0x26094640
    Cause 0000040C (Code 0x3): TLB (store) exception
    Writing crashinfo to flash:crashinfo_20101028-190957-UTC
    19:09:57 UTC Thu Oct 28 2010: TLB (store) exception, CPU signal 10, PC = 0x22774218

    --------------------------------------------------------------------
    Possible software fault. Upon reccurence, please collect
    crashinfo, "show tech" and contact Cisco Technical Support.
    --------------------------------------------------------------------

    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x21A48954z
    $0 : 00000000 00000000, AT : 00000000 29130000, v0 : 00000000 00000001, v1 : 00000000 0D8BFDC0
    a0 : 00000000 00000000, a1 : 00000000 0D8BFE04, a2 : 00000000 2A30483C, a3 : 00000000 00000004
    t0 : 00000000 00000020, t1 : 00000000 500099E1, t2 : 00000000 500081E0, t3 : FFFFFFFF FFFFFFF2
    t4 : 00000000 0000000E, t5 : 00000000 00000000, t6 : 00000000 0D8FE810, t7 : 00000000 000001FF
    s0 : 00000000 00000000, s1 : 00000000 2A3098C0, s2 : FFFFFFFF FFFFFFEC, s3 : 00000000 30F183E0
    s4 : 00000000 0D8FE81E, s5 : 00000000 2A30CC60, s6 : 00000000 00000000, s7 : 00000000 0000000E
    t8 : 00000000 000007FC, t9 : 00000000 2A30BF80, k0 : 00000000 00000000, k1 : 00000000 00000000
    gp : 00000000 2913F9A0, sp : 00000000 300A5EB8, s8 : 00000000 0000003C, ra : 00000000 227741C4
    EPC : 22774218, ErrorEPC : 80412AC4, SREG : 500099E3
    MDLO : 83A9196A, MDHI : E9785555, BadVaddr : 00000014
    CacheErr_Icache : 0x007F7F00 - 000040D8, CacheErr_Dcache : 0x00000000 - 00003640
    TagLo_Icache : 0x00000000 - 2364C303, DataLo_Icache : 0x14A400C5 - 26420004
    DataHi_Icache: 0x00000000 - 00000001
    TagLo_Dcache : 0x00000000 - 300A6103, TagHi_Dcache : 0x00000000 - 09137B01
    DataLo_Dcache: 0x11C00011 - AE380008, DataHi_Dcache : 0x00000000 - 0000000D
    TEXT_START : 0x2100EF18
    DATA_START : 0x26094640
    Cause 0000040C (Code 0x3): TLB (store) exception
    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x21A48954z

    === Flushing messages (19:09:58 UTC Thu Oct 28 2010) ===
    Buffered messages:
    *Oct 28 18:11:15.071: %LINK-3-UPDOWN: Interface SM1/0, changed state to up
    *Oct 28 18:11:17.191: %LINK-3-UPDOWN: Interface GigabitEthernet0/0, changed state to up
    *Oct 28 18:11:17.191: %LINK-3-UPDOWN: Interface GigabitEthernet0/1, changed state to down
    *Oct 28 18:11:17.191: %LINK-3-UPDOWN: Interface GigabitEthernet0/2, changed state to down
    *Oct 28 18:11:19.635: %LINK-3-UPDOWN: Interface SM1/1, changed state to up
    *Oct 28 18:11:36.743: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/0, changed state to up
    *Oct 28 18:11:37.007: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/1, changed state to up
    *Oct 28 18:11:37.159: %LINK-3-UPDOWN: Interface Foreign Exchange Station 0/1/0, changed state to up
    *Oct 28 18:11:37.159: %LINK-3-UPDOWN: Interface Foreign Exchange Station 0/1/1, changed state to up
    *Oct 28 18:12:18.739: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/0, changed state to operational status down due to cable removal
    *Oct 28 18:12:19.739: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/1, changed state to operational status down due to cable removal
    Queued messages:
    No warm reboot Storage
    *** System received a Bus Error exception ***
    signal= 0xa, code= 0x40c, context= 0x29732914
    PC = 0x22774218, SP = 0x300a5eb8, RA = 0x227741c4
    Cause Reg = 0x0000040c, Status Reg = 0x500099e3
    System Bootstrap, Version 15.0(1r)M6, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 2010 by cisco Systems, Inc.
    Total memory size = 512 MB - On-board = 512 MB, DIMM0 = 0 MB
    CISCO2911/K9 platform with 524288 Kbytes of main memory
    Main memory is configured to 72/-1(On-board/DIMM0) bit mode with ECC enabled

    Readonly ROMMON initialized
    program load complete, entry point: 0x80803000, size: 0x1b340

    IOS Image Load Test
    ___________________
    Digitally Signed Development Software
    program load complete, entry point: 0x81000000, size: 0x40b6b74
    Self decompressing the image : #################################################




    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Thursday, October 28, 2010 11:30 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    Here are the ip's and nics for the hypervisor, I noticed there was no Default Gateway so I added the VLAN1 as the gateway and i was then able to ping the mgf interface from within the mocule session however check this out when I go to my PC I ping the mgf interface and it pings twice (%50 loss) then it REBOOTS THE ROUTER!

    what do you think?

    se-172-17-17-129# show hypervisor ip
    Hostname: localhost
    Domain Name: None
    IP Config: 10.62.64.1(Subnet Mask: 255.255.255.0)
    169.254.1.1(Subnet Mask: 255.255.255.0)
    Default Gateway: None
    Preferred DNS Server: None
    Alternative DNS Server: None


    se-172-17-17-129# show hypervisor nics
    Name PCI Driver Link Speed Duplex MAC Address MTU
    vmnic0 0000:01:00.00 e1000e Down 0Mbps Half 00:23:eb:a1:12:1e 1500
    vmnic1 0000:02:00.00 bnx2 Up 1000Mbps Full 68:ef:bd:f9:33:01 1500
    vmnic2 0000:02:00.01 bnx2 Up 1000Mbps Full 68:ef:bd:f9:33:00 1500
    3 total nics



    Ken,

    In Normal conditions you should be able to ping. Can you send us the output of ¿show hypervisor ip¿ and ¿show hypervisor nics¿



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Thursday, October 28, 2010 10:29 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Mike,

    Looks like the license is good however as you can see below when I am sessioned in on the module I can't ping the mgf interface from thier either, should I be able to (i can ping the mgf interface for the 0/0 gigaethernet interface)?

    -----------------------------

    se-172-17-17-129# sho license in-use
    StoreIndex: 0 Feature: SRE-V-HOST-LIC Version: 1.0
    License Type: Evaluation
    License State: Active, In Use
    Evaluation total period: 8 weeks 4 days
    Evaluation period left: 8 weeks 2 days
    Expiry date: Fri Feb 29 18:30:10 2008
    License Count: Non-Counted
    License Priority: Low
    se-172-17-17-129#

    se-172-17-17-129# ping 10.62.64.2 (ping to VLAN1 good)
    PING 10.62.64.2 (10.62.64.2) 56(84) bytes of data.
    64 bytes from 10.62.64.2: icmp_seq=1 ttl=255 time=0.660 ms
    64 bytes from 10.62.64.2: icmp_seq=2 ttl=255 time=0.763 ms
    64 bytes from 10.62.64.2: icmp_seq=3 ttl=255 time=0.221 ms
    64 bytes from 10.62.64.2: icmp_seq=4 ttl=255 time=0.464 ms
    64 bytes from 10.62.64.2: icmp_seq=5 ttl=255 time=0.209 ms
    --- 10.62.64.2 ping statistics ---
    5 packets transmitted, 5 received, 0% packet loss, time 5ms
    rtt min/avg/max/mdev = 0.209/0.463/0.763/0.225 ms, ipg/ewma 1.297/0.549 ms
    se-172-17-17-129# ping 10.62.64.1
    PING 10.62.64.1 (10.62.64.1) 56(84) bytes of data. (ping to mgf interface not good)
    --- 10.62.64.1 ping statistics ---
    5 packets transmitted, 0 received, 100% packet loss, time 4000ms
    , ipg/ewma 1000.200/0.000 ms



    Ken,



    Can you go to the SRE module CLI and execute the following:



    show license in-use



    If you don¿t see any output that means you do not have a license enabled and IP connectivity to the mgf ip will be blocked.



    Mike





    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Thursday, October 28, 2010 12:35 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    [
    Radhika,

    I added the route to my pc and now I can ping the vlan 10.62.64.2 but not the mgf interface 10.62.64.1

    any suggestions?

    Ken

    quote]Ken,

    Is the 10.62.64.0 network a private network to you router? What network is the PC you are trying to connect from?



    If the 10.62.64.0 is a private network just in your router and you PC is in the 172.17.17.x network. Than you might need to add a route into your pc to point 10.62.64.0.x to your router gige Ip address.



    Thanks,

    Radhika





    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Wednesday, October 27, 2010 2:37 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    That was exactly it thank you.
    Now that I have SRE-V software loaded I am trying to install vSphere Client



    Go to https://ip address of the MGF interface

    but I cannot ping the MGF interface (10.62.64.1) from outside the router any suggestions?

    Current config:

    interface GigabitEthernet0/0
    description To tusqa network
    ip address 172.17.17.130 255.255.248.0

    interface SM1/0
    ip unnumbered GigabitEthernet0/0
    service-module ip address 172.17.17.129 255.255.248.0
    !Application: SRE-V Running on SMV
    service-module ip default-gateway 172.17.17.130
    service-module mgf ip address 10.62.64.1 255.255.255.0
    service-module mgf ip default-gateway 10.62.64.2
    !
    interface SM1/1
    description Internal switch interface connected to Service Module
    switchport mode trunk
    !
    interface Vlan1
    ip address 10.62.64.2 255.255.255.0
    !
    ip forward-protocol nd
    !
    ip http server
    ip http access-class 23
    ip http authentication local
    ip http secure-server
    ip http timeout-policy idle 60 life 86400 requests 10000
    !
    ip route 10.62.64.1 255.255.255.255 Vlan1
    ip route 10.62.64.2 255.255.255.255 10.62.64.1
    ip route 172.17.17.129 255.255.255.255 SM1/0
    ip route 172.17.17.130 255.255.255.255 SM1/0
    ip route 172.17.17.130 255.255.255.255 Vlan1
    ip route 172.17.17.130 255.255.255.255 172.17.17.124
    ip route 172.17.17.130 255.255.255.255 172.17.17.0





    Ken,

    I think there is a mistake in your ip route for the sm 1/0

    It should be¿ ip route 172.17.17.129 255.255.255.255 SM1/0 ¿ The router should point to the ip address assigned to service-module ip address ¿x.x.x.x¿



    Thanks,

    Radhika





    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Wednesday, October 27, 2010 1:00 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Mike,

    My FTP server is on the same network as my ISR GigabitEthernet0/0 interface (172.17.17.124 255.255.248.0)

    Can you take a look at my configuration because I am still getting same errors?

    Thanks in advance,

    Ken

    ------------------

    interface GigabitEthernet0/0
    description To tusqa network
    ip address 172.17.17.130 255.255.248.0
    duplex auto
    speed auto
    !
    interface SM1/0
    ip unnumbered GigabitEthernet0/0
    service-module fail-open
    service-module ip address 172.17.17.129 255.255.248.0
    service-module ip default-gateway 172.17.17.130
    service-module mgf ip address 10.62.64.1 255.255.255.0
    service-module mgf ip default-gateway 10.62.64.2
    !
    interface SM1/1
    description Internal switch interface connected to Service Module
    switchport mode trunk
    !
    interface Vlan1
    ip address 10.62.64.2 255.255.255.0
    !
    ip forward-protocol nd
    !
    ip http server
    ip http access-class 23
    ip http authentication local
    ip http secure-server
    ip http timeout-policy idle 60 life 86400 requests 10000
    !
    ip route 10.62.63.3 255.255.255.255 SM1/0
    ip route 10.62.64.1 255.255.255.255 Vlan1
    ip route 10.62.64.2 255.255.255.255 10.62.64.1
    ip route 172.17.17.130 255.255.255.255 SM1/0
    ip route 172.17.17.130 255.255.255.255 Vlan1
    ip route 172.17.17.130 255.255.255.255 172.17.17.124
    ip route 172.17.17.130 255.255.255.255 172.17.17.0


    Hi Ken,



    Looks like you do not have routing setup so that the module can access the ftp server where the sre-v-k9.smv.1.0.0.35.pkg is located.

    The module needs to be able to reach the ftp server in order to download the pkg file.



    Mike







    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Tuesday, October 26, 2010 4:20 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Ashwin,

    Here is what I get after the install command:




    boxer#term service-module sm 1/0 install url ftp://172.17.17.124/sre-v-k9.smv.1.0.0.35.pkg
    Proceed with installation? : y
    *Oct 26 19:56:58.283: %SM_INSTALL-6-INST_RSRC_GET: Getting resource information from SM1/0.
    *Oct 26 19:57:52.971: %SM_INSTALL-6-INST_RBIP: SM1/0 received msg: RBIP Registration Request
    Loading sre-v-k9.smv.1.0.0.35.pkg.install.sre !
    [OK - 1692/4096 bytes]
    Service module installation
    ios_version 15.1(2.18)T
    ios_image c2900-universalk9-mz
    pkg_name sre-v-k9.smv.1.0.0.35.pkg
    key_file sre-v-k9.smv.1.0.0.35.key
    helper_file sre-v-installer.smv.1.0.0.35
    Check target platform capabilities
    cpu 1865
    Resource check completed successfully. Proceeding to Install....
    boxer#
    boxer#
    boxer#
    *Oct 26 19:58:00.575: %SM_INSTALL-6-INST_RESET: SM1/0 is reset for software installation.
    *Oct 26 19:58:41.803: %SM_INSTALL-6-INST_RBIP: SM1/0 received msg: RBIP Registration Request
    *Oct 26 19:58:41.807: %SM_INSTALL-6-INST_RBIP: SM1/0 received msg: RBIP File Request
    *Oct 26 19:58:48.843: %SM_INSTALL-6-INST_RBIP: SM1/0 received msg: RBIP File Request
    *Oct 26 19:59:04.739: %SM_INSTALL-6-INST_RBIP: SM1/0 received msg: RBIP File Request
    *Oct 26 19:59:10.167: %SM_INSTALL-6-INST_RBIP: SM1/0 received msg: RBIP File Request
    *Oct 26 19:59:40.723: %SRE_SM-6-STATE_CHANGE: SM1/0 changing state from SERVICE_MODULE_STATE_ERRQ to SERVICE_MODULE_STATE_STDY
    *Oct 26 19:59:41.907: %SERVICEMODULE-2-IPCONFIGFAILED: Service module SM1/0 IP configuration (vlan default gateway) failed
    *Oct 26 20:00:23.287: %SM_INSTALL-6-INST_FAIL: SM1/0 is reset due to
    Can not download sre-v-k9.smv.1.0.0.35.pkg
    error code 0 : error type 'couldn't connect to host'.
    *Oct 26 20:00:23.287: %SRE_SM-6-STATE_CHANGE: SM1/0 changing state from SERVICE_MODULE_STATE_STDY to SERVICE_MODULE_STATE_ERRQ
    *Oct 26 20:00:23.287: %SM_INSTALL-6-INST_FAIL: SM1/0 is reset due to Unable to install. Please try again.


    Hi Ken,



    After you issue the install CLI from IOS, Can you session into the blade to capture the installation steps/logs. Please make sure you have all required files in your ftp server.



    Thanks,

    Ashwin



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Monday, October 25, 2010 5:18 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: Trouble installing SRE-V software



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    My config:

    interface SM1/0
    ip address 10.0.0.100 255.255.255.0
    service-module ip address 10.0.0.1 255.255.255.0
    service-module ip default-gateway 10.0.0.100
    service-module mgf ip address 1.10.10.5 255.255.255.0
    service-module mgf ip default-gateway 1.10.10.3
    !
    interface SM1/1
    description Internal switch interface connected to Service Module
    switchport mode trunk
    !
    interface Vlan1
    ip address 1.10.10.3 255.255.255.0
    !
    ip forward-protocol nd
    !
    ip http server
    ip http access-class 23
    ip http authentication local
    ip http secure-server
    ip http timeout-policy idle 60 life 86400 requests 10000
    !
    ip route 1.10.10.5 255.255.255.255 Vlan1

    Here is what I get when I try to install:

    Install of ftp://172.17.17.124/sre-v-k9.smv.1.0.0.35.pkg in progress
    Install status : File sre-v-k9.smv.1.0.0.35.pkg.install.sre requested
    Local Partition Info - (0 apps)
    =====================
    Retrieving partition information
    boxer#service-module sm 1/0 status
    Service Module is Cisco SM1/0
    Service Module supports session via TTY line 67
    Service Module is trying to recover from error
    Service Module heartbeat-reset is enabled
    Service Module is in fail open
    Service Module status is not available
    Module resource information:
    CPU Frequency: 1864 MHz
    Memory Size: 2535 MB
    Disk 0 Size: 500107 MB
    Disk 1 Size: 2055 MB
    Install of ftp://172.17.17.124/sre-v-k9.smv.1.0.0.35.pkg in progress
    Install status : File sre-v-k9.smv.1.0.0.35.pkg.install.sre requested
    Local Partition Info - (0 apps)
    =====================
    Retrieving partition information
    boxer#service-module sm 1/0 status
    Service Module is Cisco SM1/0
    Service Module supports session via TTY line 67
    Service Module is in Steady state
    Service Module heartbeat-reset is enabled
    Getting status from the Service Module, please wait..
    Cisco Foundation Software 1.0
    FNDN Running on SM
    Module resource information:
    CPU Frequency: 1862 MHz
    Memory Size: 4136636 MB
    Disk 0 Size: 953880 MB
    Install of ftp://172.17.17.124/sre-v-k9.smv.1.0.0.35.pkg in progress
    Install status : File sre-v-k9.smv.1.0.0.35.pkg.install.sre requested
    No local partition
    boxer#service-module sm 1/0 status
    Service Module is Cisco SM1/0
    Service Module supports session via TTY line 67
    Service Module is trying to recover from error
    Service Module heartbeat-reset is enabled
    Service Module status is not available
    Module resource information:
    CPU Frequency: 1862 MHz
    Memory Size: 4136636 MB
    Disk 0 Size: 953880 MB
    No install/uninstall in progress
    No local partition

    ---------------

    Any suggestons?
    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2678543>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2681319>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2688556>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2688752>
    or simply reply to this email.
    -- --
    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2692405>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2692542>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2692605>
    or simply reply to this email.
    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2692674>
    or simply reply to this email.
    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2690720>
    or simply reply to this email.
    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2690770>
    or simply reply to this email.

    Subject: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-
    Replied by: Radhika Miriyala on 20-11-2010 01:34:30 AM
    Ok the current config looks much cleaner. you still have the ip route ¿ip route 10.62.64.1 255.255.255.255 Van¿ which is not needed but at the same time should cause any issues.

    Can you configure the following under VAN 1 'switch port mode trunk'

    Is the crash triggered only when you ping from external to the router or it happens when you try to ping the MGF ip address from the router (not SRE)?

    Please let us know if the crash continues to happen after the switch port mode trunk  also.

    Thanks,

    Radhika

    Subject: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-
    Replied by: Ken Romo on 20-11-2010 01:34:34 AM
    Ok the current config looks much cleaner. you still have the ip route ¿ip route 10.62.64.1 255.255.255.255 Van¿ which is not needed but at the same time should cause any issues.

    OK I removed this route

    Can you configure the following under VAN 1 ¿switch port mode trunk

    I do not see the option to change VLAN1 to - switch port mode trunk

    Is the crash triggered only when you ping from external to the router or it happens when you try to ping the MGF ip address from the router (not SRE)?

    The crash happens with you ping externall to the MGF interface or from within the SRE (does not crash when you ping from router).

    Please let us know if the crash continues to happen after the switch port mode trunk also.

    How to you configure a VLAN with - switch port mode trunk ?


    Thanks again for all your help here.
    Ken


    Thanks,

    Radhika





    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Thursday, October 28, 2010 1:11 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Radhika Miriyala in Service Ready Engine Virtualizatio



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Here is current config, what woud you suggest I change?


    interface GigabitEthernet0/0
    description To tusqa network
    ip address 172.17.17.130 255.255.248.0
    !
    interface SM1/0
    ip unnumbered GigabitEthernet0/0
    service-module ip address 172.17.17.129 255.255.248.0
    !Application: SRE-V Running on SMV
    service-module ip default-gateway 172.17.17.130
    service-module mgf ip address 10.62.64.1 255.255.255.0
    service-module mgf ip default-gateway 10.62.64.2
    !
    interface SM1/1
    description Internal switch interface connected to Service Module
    switchport mode trunk
    !
    interface Vlan1
    ip address 10.62.64.2 255.255.255.0
    !
    ip forward-protocol nd
    !
    ip http server
    ip http access-class 23
    ip http authentication local
    ip http secure-server
    ip http timeout-policy idle 60 life 86400 requests 10000
    !
    ip route 10.62.64.1 255.255.255.255 Vlan1
    ip route 172.17.17.129 255.255.255.255 SM1/0




    Ken,

    I was looking at your config s sent some time back and you have ip routes to Vlan 1 . Can you please remove the two lines below and try.

    ip route 10.62.64.1 255.255.255.255 Vlan1
    ip route 172.17.17.130 255.255.255.255 Vlan1



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Thursday, October 28, 2010 12:30 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Radhika Miriyala in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Radhika Miriyala has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Thanks Ken. We will take a look at the tracebacks to see what is happening on the IOS end.



    Once the router is booted up is the module up and running? Is the ping to mgf working?



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Thursday, October 28, 2010 12:25 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Rebooting the router?? Is very strange. Do you have any console messages on the router?

    Yes see below:

    The ping was failing because the default gateway was missing. But we need to figure out why the router rebooted/ Do you have any tracebacks on the router?

    Yes see below:

    (IOS image also is a beta Image so could be a issue there) Do you have any other modules on this router?

    No other modules on the router.

    ------------------------
    %ALIGN-1-FATAL: Illegal access to a low address 19:09:57 UTC Thu Oct 28 2010
    addr=0x14, pc=0x22765BD8z , ra=0x22765B84z , sp=0x300A5EB8
    %ALIGN-1-FATAL: Illegal access to a low address 19:09:57 UTC Thu Oct 28 2010
    addr=0x14, pc=0x22765BD8z , ra=0x22765B84z , sp=0x300A5EB8

    19:09:57 UTC Thu Oct 28 2010: TLB (store) exception, CPU signal 10, PC = 0x22774218

    --------------------------------------------------------------------
    Possible software fault. Upon reccurence, please collect
    crashinfo, "show tech" and contact Cisco Technical Support.
    --------------------------------------------------------------------

    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x21A48954z
    $0 : 00000000 00000000, AT : 00000000 29130000, v0 : 00000000 00000001, v1 : 00000000 0D8BFDC0
    a0 : 00000000 00000000, a1 : 00000000 0D8BFE04, a2 : 00000000 2A30483C, a3 : 00000000 00000004
    t0 : 00000000 00000020, t1 : 00000000 500099E1, t2 : 00000000 500081E0, t3 : FFFFFFFF FFFFFFF2
    t4 : 00000000 0000000E, t5 : 00000000 00000000, t6 : 00000000 0D8FE810, t7 : 00000000 000001FF
    s0 : 00000000 00000000, s1 : 00000000 2A3098C0, s2 : FFFFFFFF FFFFFFEC, s3 : 00000000 30F183E0
    s4 : 00000000 0D8FE81E, s5 : 00000000 2A30CC60, s6 : 00000000 00000000, s7 : 00000000 0000000E
    t8 : 00000000 000007FC, t9 : 00000000 2A30BF80, k0 : 00000000 00000000, k1 : 00000000 00000000
    gp : 00000000 2913F9A0, sp : 00000000 300A5EB8, s8 : 00000000 0000003C, ra : 00000000 227741C4
    EPC : 22774218, ErrorEPC : 80412AC4, SREG : 500099E3
    MDLO : 83A9196A, MDHI : E9785555, BadVaddr : 00000014
    CacheErr_Icache : 0x007F7F00 - 000040D8, CacheErr_Dcache : 0x00000000 - 00003640
    TagLo_Icache : 0x00000000 - 2364C303, DataLo_Icache : 0x14A400C5 - 26420004
    DataHi_Icache: 0x00000000 - 00000001
    TagLo_Dcache : 0x00000000 - 300A6103, TagHi_Dcache : 0x00000000 - 09137B01
    DataLo_Dcache: 0x11C00011 - AE380008, DataHi_Dcache : 0x00000000 - 0000000D
    TEXT_START : 0x2100EF18
    DATA_START : 0x26094640
    Cause 0000040C (Code 0x3): TLB (store) exception

    19:09:57 UTC Thu Oct 28 2010: TLB (store) exception, CPU signal 10, PC = 0x22774218

    --------------------------------------------------------------------
    Possible software fault. Upon reccurence, please collect
    crashinfo, "show tech" and contact Cisco Technical Support.
    --------------------------------------------------------------------

    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x21A48954z
    $0 : 00000000 00000000, AT : 00000000 29130000, v0 : 00000000 00000001, v1 : 00000000 0D8BFDC0
    a0 : 00000000 00000000, a1 : 00000000 0D8BFE04, a2 : 00000000 2A30483C, a3 : 00000000 00000004
    t0 : 00000000 00000020, t1 : 00000000 500099E1, t2 : 00000000 500081E0, t3 : FFFFFFFF FFFFFFF2
    t4 : 00000000 0000000E, t5 : 00000000 00000000, t6 : 00000000 0D8FE810, t7 : 00000000 000001FF
    s0 : 00000000 00000000, s1 : 00000000 2A3098C0, s2 : FFFFFFFF FFFFFFEC, s3 : 00000000 30F183E0
    s4 : 00000000 0D8FE81E, s5 : 00000000 2A30CC60, s6 : 00000000 00000000, s7 : 00000000 0000000E
    t8 : 00000000 000007FC, t9 : 00000000 2A30BF80, k0 : 00000000 00000000, k1 : 00000000 00000000
    gp : 00000000 2913F9A0, sp : 00000000 300A5EB8, s8 : 00000000 0000003C, ra : 00000000 227741C4
    EPC : 22774218, ErrorEPC : 80412AC4, SREG : 500099E3
    MDLO : 83A9196A, MDHI : E9785555, BadVaddr : 00000014
    CacheErr_Icache : 0x007F7F00 - 000040D8, CacheErr_Dcache : 0x00000000 - 00003640
    TagLo_Icache : 0x00000000 - 2364C303, DataLo_Icache : 0x14A400C5 - 26420004
    DataHi_Icache: 0x00000000 - 00000001
    TagLo_Dcache : 0x00000000 - 300A6103, TagHi_Dcache : 0x00000000 - 09137B01
    DataLo_Dcache: 0x11C00011 - AE380008, DataHi_Dcache : 0x00000000 - 0000000D
    TEXT_START : 0x2100EF18
    DATA_START : 0x26094640
    Cause 0000040C (Code 0x3): TLB (store) exception
    Writing crashinfo to flash:crashinfo_20101028-190957-UTC
    19:09:57 UTC Thu Oct 28 2010: TLB (store) exception, CPU signal 10, PC = 0x22774218

    --------------------------------------------------------------------
    Possible software fault. Upon reccurence, please collect
    crashinfo, "show tech" and contact Cisco Technical Support.
    --------------------------------------------------------------------

    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x21A48954z
    $0 : 00000000 00000000, AT : 00000000 29130000, v0 : 00000000 00000001, v1 : 00000000 0D8BFDC0
    a0 : 00000000 00000000, a1 : 00000000 0D8BFE04, a2 : 00000000 2A30483C, a3 : 00000000 00000004
    t0 : 00000000 00000020, t1 : 00000000 500099E1, t2 : 00000000 500081E0, t3 : FFFFFFFF FFFFFFF2
    t4 : 00000000 0000000E, t5 : 00000000 00000000, t6 : 00000000 0D8FE810, t7 : 00000000 000001FF
    s0 : 00000000 00000000, s1 : 00000000 2A3098C0, s2 : FFFFFFFF FFFFFFEC, s3 : 00000000 30F183E0
    s4 : 00000000 0D8FE81E, s5 : 00000000 2A30CC60, s6 : 00000000 00000000, s7 : 00000000 0000000E
    t8 : 00000000 000007FC, t9 : 00000000 2A30BF80, k0 : 00000000 00000000, k1 : 00000000 00000000
    gp : 00000000 2913F9A0, sp : 00000000 300A5EB8, s8 : 00000000 0000003C, ra : 00000000 227741C4
    EPC : 22774218, ErrorEPC : 80412AC4, SREG : 500099E3
    MDLO : 83A9196A, MDHI : E9785555, BadVaddr : 00000014
    CacheErr_Icache : 0x007F7F00 - 000040D8, CacheErr_Dcache : 0x00000000 - 00003640
    TagLo_Icache : 0x00000000 - 2364C303, DataLo_Icache : 0x14A400C5 - 26420004
    DataHi_Icache: 0x00000000 - 00000001
    TagLo_Dcache : 0x00000000 - 300A6103, TagHi_Dcache : 0x00000000 - 09137B01
    DataLo_Dcache: 0x11C00011 - AE380008, DataHi_Dcache : 0x00000000 - 0000000D
    TEXT_START : 0x2100EF18
    DATA_START : 0x26094640
    Cause 0000040C (Code 0x3): TLB (store) exception
    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x21A48954z

    === Flushing messages (19:09:58 UTC Thu Oct 28 2010) ===
    Buffered messages:
    *Oct 28 18:11:15.071: %LINK-3-UPDOWN: Interface SM1/0, changed state to up
    *Oct 28 18:11:17.191: %LINK-3-UPDOWN: Interface GigabitEthernet0/0, changed state to up
    *Oct 28 18:11:17.191: %LINK-3-UPDOWN: Interface GigabitEthernet0/1, changed state to down
    *Oct 28 18:11:17.191: %LINK-3-UPDOWN: Interface GigabitEthernet0/2, changed state to down
    *Oct 28 18:11:19.635: %LINK-3-UPDOWN: Interface SM1/1, changed state to up
    *Oct 28 18:11:36.743: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/0, changed state to up
    *Oct 28 18:11:37.007: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/1, changed state to up
    *Oct 28 18:11:37.159: %LINK-3-UPDOWN: Interface Foreign Exchange Station 0/1/0, changed state to up
    *Oct 28 18:11:37.159: %LINK-3-UPDOWN: Interface Foreign Exchange Station 0/1/1, changed state to up
    *Oct 28 18:12:18.739: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/0, changed state to operational status down due to cable removal
    *Oct 28 18:12:19.739: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/1, changed state to operational status down due to cable removal
    Queued messages:
    No warm reboot Storage
    *** System received a Bus Error exception ***
    signal= 0xa, code= 0x40c, context= 0x29732914
    PC = 0x22774218, SP = 0x300a5eb8, RA = 0x227741c4
    Cause Reg = 0x0000040c, Status Reg = 0x500099e3
    System Bootstrap, Version 15.0(1r)M6, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 2010 by cisco Systems, Inc.
    Total memory size = 512 MB - On-board = 512 MB, DIMM0 = 0 MB
    CISCO2911/K9 platform with 524288 Kbytes of main memory
    Main memory is configured to 72/-1(On-board/DIMM0) bit mode with ECC enabled

    Readonly ROMMON initialized
    program load complete, entry point: 0x80803000, size: 0x1b340

    IOS Image Load Test
    ___________________
    Digitally Signed Development Software
    program load complete, entry point: 0x81000000, size: 0x40b6b74
    Self decompressing the image : #################################################




    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Thursday, October 28, 2010 11:30 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    Here are the ip's and nics for the hypervisor, I noticed there was no Default Gateway so I added the VLAN1 as the gateway and i was then able to ping the mgf interface from within the mocule session however check this out when I go to my PC I ping the mgf interface and it pings twice (%50 loss) then it REBOOTS THE ROUTER!

    what do you think?

    se-172-17-17-129# show hypervisor ip
    Hostname: localhost
    Domain Name: None
    IP Config: 10.62.64.1(Subnet Mask: 255.255.255.0)
    169.254.1.1(Subnet Mask: 255.255.255.0)
    Default Gateway: None
    Preferred DNS Server: None
    Alternative DNS Server: None


    se-172-17-17-129# show hypervisor nics
    Name PCI Driver Link Speed Duplex MAC Address MTU
    vmnic0 0000:01:00.00 e1000e Down 0Mbps Half 00:23:eb:a1:12:1e 1500
    vmnic1 0000:02:00.00 bnx2 Up 1000Mbps Full 68:ef:bd:f9:33:01 1500
    vmnic2 0000:02:00.01 bnx2 Up 1000Mbps Full 68:ef:bd:f9:33:00 1500
    3 total nics



    Ken,

    In Normal conditions you should be able to ping. Can you send us the output of ¿show hypervisor ip¿ and ¿show hypervisor nics¿



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Thursday, October 28, 2010 10:29 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Mike,

    Looks like the license is good however as you can see below when I am sessioned in on the module I can't ping the mgf interface from thier either, should I be able to (i can ping the mgf interface for the 0/0 gigaethernet interface)?

    -----------------------------

    se-172-17-17-129# sho license in-use
    StoreIndex: 0 Feature: SRE-V-HOST-LIC Version: 1.0
    License Type: Evaluation
    License State: Active, In Use
    Evaluation total period: 8 weeks 4 days
    Evaluation period left: 8 weeks 2 days
    Expiry date: Fri Feb 29 18:30:10 2008
    License Count: Non-Counted
    License Priority: Low
    se-172-17-17-129#

    se-172-17-17-129# ping 10.62.64.2 (ping to VLAN1 good)
    PING 10.62.64.2 (10.62.64.2) 56(84) bytes of data.
    64 bytes from 10.62.64.2: icmp_seq=1 ttl=255 time=0.660 ms
    64 bytes from 10.62.64.2: icmp_seq=2 ttl=255 time=0.763 ms
    64 bytes from 10.62.64.2: icmp_seq=3 ttl=255 time=0.221 ms
    64 bytes from 10.62.64.2: icmp_seq=4 ttl=255 time=0.464 ms
    64 bytes from 10.62.64.2: icmp_seq=5 ttl=255 time=0.209 ms
    --- 10.62.64.2 ping statistics ---
    5 packets transmitted, 5 received, 0% packet loss, time 5ms
    rtt min/avg/max/mdev = 0.209/0.463/0.763/0.225 ms, ipg/ewma 1.297/0.549 ms
    se-172-17-17-129# ping 10.62.64.1
    PING 10.62.64.1 (10.62.64.1) 56(84) bytes of data. (ping to mgf interface not good)
    --- 10.62.64.1 ping statistics ---
    5 packets transmitted, 0 received, 100% packet loss, time 4000ms
    , ipg/ewma 1000.200/0.000 ms



    Ken,



    Can you go to the SRE module CLI and execute the following:



    show license in-use



    If you don¿t see any output that means you do not have a license enabled and IP connectivity to the mgf ip will be blocked.



    Mike





    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Thursday, October 28, 2010 12:35 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    [
    Radhika,

    I added the route to my pc and now I can ping the vlan 10.62.64.2 but not the mgf interface 10.62.64.1

    any suggestions?

    Ken

    quote]Ken,

    Is the 10.62.64.0 network a private network to you router? What network is the PC you are trying to connect from?



    If the 10.62.64.0 is a private network just in your router and you PC is in the 172.17.17.x network. Than you might need to add a route into your pc to point 10.62.64.0.x to your router gige Ip address.



    Thanks,

    Radhika





    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Wednesday, October 27, 2010 2:37 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    That was exactly it thank you.
    Now that I have SRE-V software loaded I am trying to install vSphere Client



    Go to https://ip address of the MGF interface

    but I cannot ping the MGF interface (10.62.64.1) from outside the router any suggestions?

    Current config:

    interface GigabitEthernet0/0
    description To tusqa network
    ip address 172.17.17.130 255.255.248.0

    interface SM1/0
    ip unnumbered GigabitEthernet0/0
    service-module ip address 172.17.17.129 255.255.248.0
    !Application: SRE-V Running on SMV
    service-module ip default-gateway 172.17.17.130
    service-module mgf ip address 10.62.64.1 255.255.255.0
    service-module mgf ip default-gateway 10.62.64.2
    !
    interface SM1/1
    description Internal switch interface connected to Service Module
    switchport mode trunk
    !
    interface Vlan1
    ip address 10.62.64.2 255.255.255.0
    !
    ip forward-protocol nd
    !
    ip http server
    ip http access-class 23
    ip http authentication local
    ip http secure-server
    ip http timeout-policy idle 60 life 86400 requests 10000
    !
    ip route 10.62.64.1 255.255.255.255 Vlan1
    ip route 10.62.64.2 255.255.255.255 10.62.64.1
    ip route 172.17.17.129 255.255.255.255 SM1/0
    ip route 172.17.17.130 255.255.255.255 SM1/0
    ip route 172.17.17.130 255.255.255.255 Vlan1
    ip route 172.17.17.130 255.255.255.255 172.17.17.124
    ip route 172.17.17.130 255.255.255.255 172.17.17.0





    Ken,

    I think there is a mistake in your ip route for the sm 1/0

    It should be¿ ip route 172.17.17.129 255.255.255.255 SM1/0 ¿ The router should point to the ip address assigned to service-module ip address ¿x.x.x.x¿



    Thanks,

    Radhika





    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Wednesday, October 27, 2010 1:00 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Mike,

    My FTP server is on the same network as my ISR GigabitEthernet0/0 interface (172.17.17.124 255.255.248.0)

    Can you take a look at my configuration because I am still getting same errors?

    Thanks in advance,

    Ken

    ------------------

    interface GigabitEthernet0/0
    description To tusqa network
    ip address 172.17.17.130 255.255.248.0
    duplex auto
    speed auto
    !
    interface SM1/0
    ip unnumbered GigabitEthernet0/0
    service-module fail-open
    service-module ip address 172.17.17.129 255.255.248.0
    service-module ip default-gateway 172.17.17.130
    service-module mgf ip address 10.62.64.1 255.255.255.0
    service-module mgf ip default-gateway 10.62.64.2
    !
    interface SM1/1
    description Internal switch interface connected to Service Module
    switchport mode trunk
    !
    interface Vlan1
    ip address 10.62.64.2 255.255.255.0
    !
    ip forward-protocol nd
    !
    ip http server
    ip http access-class 23
    ip http authentication local
    ip http secure-server
    ip http timeout-policy idle 60 life 86400 requests 10000
    !
    ip route 10.62.63.3 255.255.255.255 SM1/0
    ip route 10.62.64.1 255.255.255.255 Vlan1
    ip route 10.62.64.2 255.255.255.255 10.62.64.1
    ip route 172.17.17.130 255.255.255.255 SM1/0
    ip route 172.17.17.130 255.255.255.255 Vlan1
    ip route 172.17.17.130 255.255.255.255 172.17.17.124
    ip route 172.17.17.130 255.255.255.255 172.17.17.0


    Hi Ken,



    Looks like you do not have routing setup so that the module can access the ftp server where the sre-v-k9.smv.1.0.0.35.pkg is located.

    The module needs to be able to reach the ftp server in order to download the pkg file.



    Mike







    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Tuesday, October 26, 2010 4:20 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Ashwin,

    Here is what I get after the install command:




    boxer#term service-module sm 1/0 install url ftp://172.17.17.124/sre-v-k9.smv.1.0.0.35.pkg
    Proceed with installation? : y
    *Oct 26 19:56:58.283: %SM_INSTALL-6-INST_RSRC_GET: Getting resource information from SM1/0.
    *Oct 26 19:57:52.971: %SM_INSTALL-6-INST_RBIP: SM1/0 received msg: RBIP Registration Request
    Loading sre-v-k9.smv.1.0.0.35.pkg.install.sre !
    [OK - 1692/4096 bytes]
    Service module installation
    ios_version 15.1(2.18)T
    ios_image c2900-universalk9-mz
    pkg_name sre-v-k9.smv.1.0.0.35.pkg
    key_file sre-v-k9.smv.1.0.0.35.key
    helper_file sre-v-installer.smv.1.0.0.35
    Check target platform capabilities
    cpu 1865
    Resource check completed successfully. Proceeding to Install....
    boxer#
    boxer#
    boxer#
    *Oct 26 19:58:00.575: %SM_INSTALL-6-INST_RESET: SM1/0 is reset for software installation.
    *Oct 26 19:58:41.803: %SM_INSTALL-6-INST_RBIP: SM1/0 received msg: RBIP Registration Request
    *Oct 26 19:58:41.807: %SM_INSTALL-6-INST_RBIP: SM1/0 received msg: RBIP File Request
    *Oct 26 19:58:48.843: %SM_INSTALL-6-INST_RBIP: SM1/0 received msg: RBIP File Request
    *Oct 26 19:59:04.739: %SM_INSTALL-6-INST_RBIP: SM1/0 received msg: RBIP File Request
    *Oct 26 19:59:10.167: %SM_INSTALL-6-INST_RBIP: SM1/0 received msg: RBIP File Request
    *Oct 26 19:59:40.723: %SRE_SM-6-STATE_CHANGE: SM1/0 changing state from SERVICE_MODULE_STATE_ERRQ to SERVICE_MODULE_STATE_STDY
    *Oct 26 19:59:41.907: %SERVICEMODULE-2-IPCONFIGFAILED: Service module SM1/0 IP configuration (vlan default gateway) failed
    *Oct 26 20:00:23.287: %SM_INSTALL-6-INST_FAIL: SM1/0 is reset due to
    Can not download sre-v-k9.smv.1.0.0.35.pkg
    error code 0 : error type 'couldn't connect to host'.
    *Oct 26 20:00:23.287: %SRE_SM-6-STATE_CHANGE: SM1/0 changing state from SERVICE_MODULE_STATE_STDY to SERVICE_MODULE_STATE_ERRQ
    *Oct 26 20:00:23.287: %SM_INSTALL-6-INST_FAIL: SM1/0 is reset due to Unable to install. Please try again.


    Hi Ken,



    After you issue the install CLI from IOS, Can you session into the blade to capture the installation steps/logs. Please make sure you have all required files in your ftp server.



    Thanks,

    Ashwin



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Monday, October 25, 2010 5:18 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: Trouble installing SRE-V software



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    My config:

    interface SM1/0
    ip address 10.0.0.100 255.255.255.0
    service-module ip address 10.0.0.1 255.255.255.0
    service-module ip default-gateway 10.0.0.100
    service-module mgf ip address 1.10.10.5 255.255.255.0
    service-module mgf ip default-gateway 1.10.10.3
    !
    interface SM1/1
    description Internal switch interface connected to Service Module
    switchport mode trunk
    !
    interface Vlan1
    ip address 1.10.10.3 255.255.255.0
    !
    ip forward-protocol nd
    !
    ip http server
    ip http access-class 23
    ip http authentication local
    ip http secure-server
    ip http timeout-policy idle 60 life 86400 requests 10000
    !
    ip route 1.10.10.5 255.255.255.255 Vlan1

    Here is what I get when I try to install:

    Install of ftp://172.17.17.124/sre-v-k9.smv.1.0.0.35.pkg in progress
    Install status : File sre-v-k9.smv.1.0.0.35.pkg.install.sre requested
    Local Partition Info - (0 apps)
    =====================
    Retrieving partition information
    boxer#service-module sm 1/0 status
    Service Module is Cisco SM1/0
    Service Module supports session via TTY line 67
    Service Module is trying to recover from error
    Service Module heartbeat-reset is enabled
    Service Module is in fail open
    Service Module status is not available
    Module resource information:
    CPU Frequency: 1864 MHz
    Memory Size: 2535 MB
    Disk 0 Size: 500107 MB
    Disk 1 Size: 2055 MB
    Install of ftp://172.17.17.124/sre-v-k9.smv.1.0.0.35.pkg in progress
    Install status : File sre-v-k9.smv.1.0.0.35.pkg.install.sre requested
    Local Partition Info - (0 apps)
    =====================
    Retrieving partition information
    boxer#service-module sm 1/0 status
    Service Module is Cisco SM1/0
    Service Module supports session via TTY line 67
    Service Module is in Steady state
    Service Module heartbeat-reset is enabled
    Getting status from the Service Module, please wait..
    Cisco Foundation Software 1.0
    FNDN Running on SM
    Module resource information:
    CPU Frequency: 1862 MHz
    Memory Size: 4136636 MB
    Disk 0 Size: 953880 MB
    Install of ftp://172.17.17.124/sre-v-k9.smv.1.0.0.35.pkg in progress
    Install status : File sre-v-k9.smv.1.0.0.35.pkg.install.sre requested
    No local partition
    boxer#service-module sm 1/0 status
    Service Module is Cisco SM1/0
    Service Module supports session via TTY line 67
    Service Module is trying to recover from error
    Service Module heartbeat-reset is enabled
    Service Module status is not available
    Module resource information:
    CPU Frequency: 1862 MHz
    Memory Size: 4136636 MB
    Disk 0 Size: 953880 MB
    No install/uninstall in progress
    No local partition

    ---------------

    Any suggestons?
    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2678543>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2681319>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2688556>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2688752>
    or simply reply to this email.
    -- --
    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2692405>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2692542>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2692605>
    or simply reply to this email.
    -- --
    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2692674>
    or simply reply to this email.
    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2690720>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2690827>
    or simply reply to this email.



     

    Subject: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-
    Replied by: Radhika Miriyala on 20-11-2010 01:34:34 AM
    From the router

    Router# configure termina;

    Router(Config)#interface vlan 1

    Router(config-if) switchport mode trunk

    Router(config-if) end









    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Thursday, October 28, 2010 2:16 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------

    Ok the current config looks much cleaner. you still have the ip route ¿ip route 10.62.64.1 255.255.255.255 Van¿ which is not needed but at the same time should cause any issues.

    OK I removed this route

    Can you configure the following under VAN 1 ¿switch port mode trunk

    I do not see the option to change VLAN1 to - switch port mode trunk

    Is the crash triggered only when you ping from external to the router or it happens when you try to ping the MGF ip address from the router (not SRE)?

    The crash happens with you ping externall to the MGF interface or from within the SRE (does not crash when you ping from router).

    Please let us know if the crash continues to happen after the switch port mode trunk also.

    How to you configure a VLAN with - switch port mode trunk ?


    Thanks again for all your help here.
    Ken


    Thanks,

    Radhika





    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Thursday, October 28, 2010 1:11 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Radhika Miriyala in Service Ready Engine Virtualizatio



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Here is current config, what woud you suggest I change?


    interface GigabitEthernet0/0
    description To tusqa network
    ip address 172.17.17.130 255.255.248.0
    !
    interface SM1/0
    ip unnumbered GigabitEthernet0/0
    service-module ip address 172.17.17.129 255.255.248.0
    !Application: SRE-V Running on SMV
    service-module ip default-gateway 172.17.17.130
    service-module mgf ip address 10.62.64.1 255.255.255.0
    service-module mgf ip default-gateway 10.62.64.2
    !
    interface SM1/1
    description Internal switch interface connected to Service Module
    switchport mode trunk
    !
    interface Vlan1
    ip address 10.62.64.2 255.255.255.0
    !
    ip forward-protocol nd
    !
    ip http server
    ip http access-class 23
    ip http authentication local
    ip http secure-server
    ip http timeout-policy idle 60 life 86400 requests 10000
    !
    ip route 10.62.64.1 255.255.255.255 Vlan1
    ip route 172.17.17.129 255.255.255.255 SM1/0




    Ken,

    I was looking at your config s sent some time back and you have ip routes to Vlan 1 . Can you please remove the two lines below and try.

    ip route 10.62.64.1 255.255.255.255 Vlan1
    ip route 172.17.17.130 255.255.255.255 Vlan1



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Thursday, October 28, 2010 12:30 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Radhika Miriyala in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Radhika Miriyala has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Thanks Ken. We will take a look at the tracebacks to see what is happening on the IOS end.



    Once the router is booted up is the module up and running? Is the ping to mgf working?



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Thursday, October 28, 2010 12:25 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Rebooting the router?? Is very strange. Do you have any console messages on the router?

    Yes see below:

    The ping was failing because the default gateway was missing. But we need to figure out why the router rebooted/ Do you have any tracebacks on the router?

    Yes see below:

    (IOS image also is a beta Image so could be a issue there) Do you have any other modules on this router?

    No other modules on the router.

    ------------------------
    %ALIGN-1-FATAL: Illegal access to a low address 19:09:57 UTC Thu Oct 28 2010
    addr=0x14, pc=0x22765BD8z , ra=0x22765B84z , sp=0x300A5EB8
    %ALIGN-1-FATAL: Illegal access to a low address 19:09:57 UTC Thu Oct 28 2010
    addr=0x14, pc=0x22765BD8z , ra=0x22765B84z , sp=0x300A5EB8

    19:09:57 UTC Thu Oct 28 2010: TLB (store) exception, CPU signal 10, PC = 0x22774218

    --------------------------------------------------------------------
    Possible software fault. Upon reccurence, please collect
    crashinfo, "show tech" and contact Cisco Technical Support.
    --------------------------------------------------------------------

    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x21A48954z
    $0 : 00000000 00000000, AT : 00000000 29130000, v0 : 00000000 00000001, v1 : 00000000 0D8BFDC0
    a0 : 00000000 00000000, a1 : 00000000 0D8BFE04, a2 : 00000000 2A30483C, a3 : 00000000 00000004
    t0 : 00000000 00000020, t1 : 00000000 500099E1, t2 : 00000000 500081E0, t3 : FFFFFFFF FFFFFFF2
    t4 : 00000000 0000000E, t5 : 00000000 00000000, t6 : 00000000 0D8FE810, t7 : 00000000 000001FF
    s0 : 00000000 00000000, s1 : 00000000 2A3098C0, s2 : FFFFFFFF FFFFFFEC, s3 : 00000000 30F183E0
    s4 : 00000000 0D8FE81E, s5 : 00000000 2A30CC60, s6 : 00000000 00000000, s7 : 00000000 0000000E
    t8 : 00000000 000007FC, t9 : 00000000 2A30BF80, k0 : 00000000 00000000, k1 : 00000000 00000000
    gp : 00000000 2913F9A0, sp : 00000000 300A5EB8, s8 : 00000000 0000003C, ra : 00000000 227741C4
    EPC : 22774218, ErrorEPC : 80412AC4, SREG : 500099E3
    MDLO : 83A9196A, MDHI : E9785555, BadVaddr : 00000014
    CacheErr_Icache : 0x007F7F00 - 000040D8, CacheErr_Dcache : 0x00000000 - 00003640
    TagLo_Icache : 0x00000000 - 2364C303, DataLo_Icache : 0x14A400C5 - 26420004
    DataHi_Icache: 0x00000000 - 00000001
    TagLo_Dcache : 0x00000000 - 300A6103, TagHi_Dcache : 0x00000000 - 09137B01
    DataLo_Dcache: 0x11C00011 - AE380008, DataHi_Dcache : 0x00000000 - 0000000D
    TEXT_START : 0x2100EF18
    DATA_START : 0x26094640
    Cause 0000040C (Code 0x3): TLB (store) exception

    19:09:57 UTC Thu Oct 28 2010: TLB (store) exception, CPU signal 10, PC = 0x22774218

    --------------------------------------------------------------------
    Possible software fault. Upon reccurence, please collect
    crashinfo, "show tech" and contact Cisco Technical Support.
    --------------------------------------------------------------------

    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x21A48954z
    $0 : 00000000 00000000, AT : 00000000 29130000, v0 : 00000000 00000001, v1 : 00000000 0D8BFDC0
    a0 : 00000000 00000000, a1 : 00000000 0D8BFE04, a2 : 00000000 2A30483C, a3 : 00000000 00000004
    t0 : 00000000 00000020, t1 : 00000000 500099E1, t2 : 00000000 500081E0, t3 : FFFFFFFF FFFFFFF2
    t4 : 00000000 0000000E, t5 : 00000000 00000000, t6 : 00000000 0D8FE810, t7 : 00000000 000001FF
    s0 : 00000000 00000000, s1 : 00000000 2A3098C0, s2 : FFFFFFFF FFFFFFEC, s3 : 00000000 30F183E0
    s4 : 00000000 0D8FE81E, s5 : 00000000 2A30CC60, s6 : 00000000 00000000, s7 : 00000000 0000000E
    t8 : 00000000 000007FC, t9 : 00000000 2A30BF80, k0 : 00000000 00000000, k1 : 00000000 00000000
    gp : 00000000 2913F9A0, sp : 00000000 300A5EB8, s8 : 00000000 0000003C, ra : 00000000 227741C4
    EPC : 22774218, ErrorEPC : 80412AC4, SREG : 500099E3
    MDLO : 83A9196A, MDHI : E9785555, BadVaddr : 00000014
    CacheErr_Icache : 0x007F7F00 - 000040D8, CacheErr_Dcache : 0x00000000 - 00003640
    TagLo_Icache : 0x00000000 - 2364C303, DataLo_Icache : 0x14A400C5 - 26420004
    DataHi_Icache: 0x00000000 - 00000001
    TagLo_Dcache : 0x00000000 - 300A6103, TagHi_Dcache : 0x00000000 - 09137B01
    DataLo_Dcache: 0x11C00011 - AE380008, DataHi_Dcache : 0x00000000 - 0000000D
    TEXT_START : 0x2100EF18
    DATA_START : 0x26094640
    Cause 0000040C (Code 0x3): TLB (store) exception
    Writing crashinfo to flash:crashinfo_20101028-190957-UTC
    19:09:57 UTC Thu Oct 28 2010: TLB (store) exception, CPU signal 10, PC = 0x22774218

    --------------------------------------------------------------------
    Possible software fault. Upon reccurence, please collect
    crashinfo, "show tech" and contact Cisco Technical Support.
    --------------------------------------------------------------------

    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x21A48954z
    $0 : 00000000 00000000, AT : 00000000 29130000, v0 : 00000000 00000001, v1 : 00000000 0D8BFDC0
    a0 : 00000000 00000000, a1 : 00000000 0D8BFE04, a2 : 00000000 2A30483C, a3 : 00000000 00000004
    t0 : 00000000 00000020, t1 : 00000000 500099E1, t2 : 00000000 500081E0, t3 : FFFFFFFF FFFFFFF2
    t4 : 00000000 0000000E, t5 : 00000000 00000000, t6 : 00000000 0D8FE810, t7 : 00000000 000001FF
    s0 : 00000000 00000000, s1 : 00000000 2A3098C0, s2 : FFFFFFFF FFFFFFEC, s3 : 00000000 30F183E0
    s4 : 00000000 0D8FE81E, s5 : 00000000 2A30CC60, s6 : 00000000 00000000, s7 : 00000000 0000000E
    t8 : 00000000 000007FC, t9 : 00000000 2A30BF80, k0 : 00000000 00000000, k1 : 00000000 00000000
    gp : 00000000 2913F9A0, sp : 00000000 300A5EB8, s8 : 00000000 0000003C, ra : 00000000 227741C4
    EPC : 22774218, ErrorEPC : 80412AC4, SREG : 500099E3
    MDLO : 83A9196A, MDHI : E9785555, BadVaddr : 00000014
    CacheErr_Icache : 0x007F7F00 - 000040D8, CacheErr_Dcache : 0x00000000 - 00003640
    TagLo_Icache : 0x00000000 - 2364C303, DataLo_Icache : 0x14A400C5 - 26420004
    DataHi_Icache: 0x00000000 - 00000001
    TagLo_Dcache : 0x00000000 - 300A6103, TagHi_Dcache : 0x00000000 - 09137B01
    DataLo_Dcache: 0x11C00011 - AE380008, DataHi_Dcache : 0x00000000 - 0000000D
    TEXT_START : 0x2100EF18
    DATA_START : 0x26094640
    Cause 0000040C (Code 0x3): TLB (store) exception
    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x21A48954z

    === Flushing messages (19:09:58 UTC Thu Oct 28 2010) ===
    Buffered messages:
    *Oct 28 18:11:15.071: %LINK-3-UPDOWN: Interface SM1/0, changed state to up
    *Oct 28 18:11:17.191: %LINK-3-UPDOWN: Interface GigabitEthernet0/0, changed state to up
    *Oct 28 18:11:17.191: %LINK-3-UPDOWN: Interface GigabitEthernet0/1, changed state to down
    *Oct 28 18:11:17.191: %LINK-3-UPDOWN: Interface GigabitEthernet0/2, changed state to down
    *Oct 28 18:11:19.635: %LINK-3-UPDOWN: Interface SM1/1, changed state to up
    *Oct 28 18:11:36.743: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/0, changed state to up
    *Oct 28 18:11:37.007: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/1, changed state to up
    *Oct 28 18:11:37.159: %LINK-3-UPDOWN: Interface Foreign Exchange Station 0/1/0, changed state to up
    *Oct 28 18:11:37.159: %LINK-3-UPDOWN: Interface Foreign Exchange Station 0/1/1, changed state to up
    *Oct 28 18:12:18.739: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/0, changed state to operational status down due to cable removal
    *Oct 28 18:12:19.739: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/1, changed state to operational status down due to cable removal
    Queued messages:
    No warm reboot Storage
    *** System received a Bus Error exception ***
    signal= 0xa, code= 0x40c, context= 0x29732914
    PC = 0x22774218, SP = 0x300a5eb8, RA = 0x227741c4
    Cause Reg = 0x0000040c, Status Reg = 0x500099e3
    System Bootstrap, Version 15.0(1r)M6, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 2010 by cisco Systems, Inc.
    Total memory size = 512 MB - On-board = 512 MB, DIMM0 = 0 MB
    CISCO2911/K9 platform with 524288 Kbytes of main memory
    Main memory is configured to 72/-1(On-board/DIMM0) bit mode with ECC enabled

    Readonly ROMMON initialized
    program load complete, entry point: 0x80803000, size: 0x1b340

    IOS Image Load Test
    ___________________
    Digitally Signed Development Software
    program load complete, entry point: 0x81000000, size: 0x40b6b74
    Self decompressing the image : #################################################




    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Thursday, October 28, 2010 11:30 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    Here are the ip's and nics for the hypervisor, I noticed there was no Default Gateway so I added the VLAN1 as the gateway and i was then able to ping the mgf interface from within the mocule session however check this out when I go to my PC I ping the mgf interface and it pings twice (%50 loss) then it REBOOTS THE ROUTER!

    what do you think?

    se-172-17-17-129# show hypervisor ip
    Hostname: localhost
    Domain Name: None
    IP Config: 10.62.64.1(Subnet Mask: 255.255.255.0)
    169.254.1.1(Subnet Mask: 255.255.255.0)
    Default Gateway: None
    Preferred DNS Server: None
    Alternative DNS Server: None


    se-172-17-17-129# show hypervisor nics
    Name PCI Driver Link Speed Duplex MAC Address MTU
    vmnic0 0000:01:00.00 e1000e Down 0Mbps Half 00:23:eb:a1:12:1e 1500
    vmnic1 0000:02:00.00 bnx2 Up 1000Mbps Full 68:ef:bd:f9:33:01 1500
    vmnic2 0000:02:00.01 bnx2 Up 1000Mbps Full 68:ef:bd:f9:33:00 1500
    3 total nics



    Ken,

    In Normal conditions you should be able to ping. Can you send us the output of ¿show hypervisor ip¿ and ¿show hypervisor nics¿



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Thursday, October 28, 2010 10:29 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Mike,

    Looks like the license is good however as you can see below when I am sessioned in on the module I can't ping the mgf interface from thier either, should I be able to (i can ping the mgf interface for the 0/0 gigaethernet interface)?

    -----------------------------

    se-172-17-17-129# sho license in-use
    StoreIndex: 0 Feature: SRE-V-HOST-LIC Version: 1.0
    License Type: Evaluation
    License State: Active, In Use
    Evaluation total period: 8 weeks 4 days
    Evaluation period left: 8 weeks 2 days
    Expiry date: Fri Feb 29 18:30:10 2008
    License Count: Non-Counted
    License Priority: Low
    se-172-17-17-129#

    se-172-17-17-129# ping 10.62.64.2 (ping to VLAN1 good)
    PING 10.62.64.2 (10.62.64.2) 56(84) bytes of data.
    64 bytes from 10.62.64.2: icmp_seq=1 ttl=255 time=0.660 ms
    64 bytes from 10.62.64.2: icmp_seq=2 ttl=255 time=0.763 ms
    64 bytes from 10.62.64.2: icmp_seq=3 ttl=255 time=0.221 ms
    64 bytes from 10.62.64.2: icmp_seq=4 ttl=255 time=0.464 ms
    64 bytes from 10.62.64.2: icmp_seq=5 ttl=255 time=0.209 ms
    --- 10.62.64.2 ping statistics ---
    5 packets transmitted, 5 received, 0% packet loss, time 5ms
    rtt min/avg/max/mdev = 0.209/0.463/0.763/0.225 ms, ipg/ewma 1.297/0.549 ms
    se-172-17-17-129# ping 10.62.64.1
    PING 10.62.64.1 (10.62.64.1) 56(84) bytes of data. (ping to mgf interface not good)
    --- 10.62.64.1 ping statistics ---
    5 packets transmitted, 0 received, 100% packet loss, time 4000ms
    , ipg/ewma 1000.200/0.000 ms



    Ken,



    Can you go to the SRE module CLI and execute the following:



    show license in-use



    If you don¿t see any output that means you do not have a license enabled and IP connectivity to the mgf ip will be blocked.



    Mike





    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Thursday, October 28, 2010 12:35 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    [
    Radhika,

    I added the route to my pc and now I can ping the vlan 10.62.64.2 but not the mgf interface 10.62.64.1

    any suggestions?

    Ken

    quote]Ken,

    Is the 10.62.64.0 network a private network to you router? What network is the PC you are trying to connect from?



    If the 10.62.64.0 is a private network just in your router and you PC is in the 172.17.17.x network. Than you might need to add a route into your pc to point 10.62.64.0.x to your router gige Ip address.



    Thanks,

    Radhika





    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Wednesday, October 27, 2010 2:37 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    That was exactly it thank you.
    Now that I have SRE-V software loaded I am trying to install vSphere Client



    Go to https://ip address of the MGF interface

    but I cannot ping the MGF interface (10.62.64.1) from outside the router any suggestions?

    Current config:

    interface GigabitEthernet0/0
    description To tusqa network
    ip address 172.17.17.130 255.255.248.0

    interface SM1/0
    ip unnumbered GigabitEthernet0/0
    service-module ip address 172.17.17.129 255.255.248.0
    !Application: SRE-V Running on SMV
    service-module ip default-gateway 172.17.17.130
    service-module mgf ip address 10.62.64.1 255.255.255.0
    service-module mgf ip default-gateway 10.62.64.2
    !
    interface SM1/1
    description Internal switch interface connected to Service Module
    switchport mode trunk
    !
    interface Vlan1
    ip address 10.62.64.2 255.255.255.0
    !
    ip forward-protocol nd
    !
    ip http server
    ip http access-class 23
    ip http authentication local
    ip http secure-server
    ip http timeout-policy idle 60 life 86400 requests 10000
    !
    ip route 10.62.64.1 255.255.255.255 Vlan1
    ip route 10.62.64.2 255.255.255.255 10.62.64.1
    ip route 172.17.17.129 255.255.255.255 SM1/0
    ip route 172.17.17.130 255.255.255.255 SM1/0
    ip route 172.17.17.130 255.255.255.255 Vlan1
    ip route 172.17.17.130 255.255.255.255 172.17.17.124
    ip route 172.17.17.130 255.255.255.255 172.17.17.0





    Ken,

    I think there is a mistake in your ip route for the sm 1/0

    It should be¿ ip route 172.17.17.129 255.255.255.255 SM1/0 ¿ The router should point to the ip address assigned to service-module ip address ¿x.x.x.x¿



    Thanks,

    Radhika





    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Wednesday, October 27, 2010 1:00 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Mike,

    My FTP server is on the same network as my ISR GigabitEthernet0/0 interface (172.17.17.124 255.255.248.0)

    Can you take a look at my configuration because I am still getting same errors?

    Thanks in advance,

    Ken

    ------------------

    interface GigabitEthernet0/0
    description To tusqa network
    ip address 172.17.17.130 255.255.248.0
    duplex auto
    speed auto
    !
    interface SM1/0
    ip unnumbered GigabitEthernet0/0
    service-module fail-open
    service-module ip address 172.17.17.129 255.255.248.0
    service-module ip default-gateway 172.17.17.130
    service-module mgf ip address 10.62.64.1 255.255.255.0
    service-module mgf ip default-gateway 10.62.64.2
    !
    interface SM1/1
    description Internal switch interface connected to Service Module
    switchport mode trunk
    !
    interface Vlan1
    ip address 10.62.64.2 255.255.255.0
    !
    ip forward-protocol nd
    !
    ip http server
    ip http access-class 23
    ip http authentication local
    ip http secure-server
    ip http timeout-policy idle 60 life 86400 requests 10000
    !
    ip route 10.62.63.3 255.255.255.255 SM1/0
    ip route 10.62.64.1 255.255.255.255 Vlan1
    ip route 10.62.64.2 255.255.255.255 10.62.64.1
    ip route 172.17.17.130 255.255.255.255 SM1/0
    ip route 172.17.17.130 255.255.255.255 Vlan1
    ip route 172.17.17.130 255.255.255.255 172.17.17.124
    ip route 172.17.17.130 255.255.255.255 172.17.17.0


    Hi Ken,



    Looks like you do not have routing setup so that the module can access the ftp server where the sre-v-k9.smv.1.0.0.35.pkg is located.

    The module needs to be able to reach the ftp server in order to download the pkg file.



    Mike







    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Tuesday, October 26, 2010 4:20 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Ashwin,

    Here is what I get after the install command:




    boxer#term service-module sm 1/0 install url ftp://172.17.17.124/sre-v-k9.smv.1.0.0.35.pkg
    Proceed with installation? : y
    *Oct 26 19:56:58.283: %SM_INSTALL-6-INST_RSRC_GET: Getting resource information from SM1/0.
    *Oct 26 19:57:52.971: %SM_INSTALL-6-INST_RBIP: SM1/0 received msg: RBIP Registration Request
    Loading sre-v-k9.smv.1.0.0.35.pkg.install.sre !
    [OK - 1692/4096 bytes]
    Service module installation
    ios_version 15.1(2.18)T
    ios_image c2900-universalk9-mz
    pkg_name sre-v-k9.smv.1.0.0.35.pkg
    key_file sre-v-k9.smv.1.0.0.35.key
    helper_file sre-v-installer.smv.1.0.0.35
    Check target platform capabilities
    cpu 1865
    Resource check completed successfully. Proceeding to Install....
    boxer#
    boxer#
    boxer#
    *Oct 26 19:58:00.575: %SM_INSTALL-6-INST_RESET: SM1/0 is reset for software installation.
    *Oct 26 19:58:41.803: %SM_INSTALL-6-INST_RBIP: SM1/0 received msg: RBIP Registration Request
    *Oct 26 19:58:41.807: %SM_INSTALL-6-INST_RBIP: SM1/0 received msg: RBIP File Request
    *Oct 26 19:58:48.843: %SM_INSTALL-6-INST_RBIP: SM1/0 received msg: RBIP File Request
    *Oct 26 19:59:04.739: %SM_INSTALL-6-INST_RBIP: SM1/0 received msg: RBIP File Request
    *Oct 26 19:59:10.167: %SM_INSTALL-6-INST_RBIP: SM1/0 received msg: RBIP File Request
    *Oct 26 19:59:40.723: %SRE_SM-6-STATE_CHANGE: SM1/0 changing state from SERVICE_MODULE_STATE_ERRQ to SERVICE_MODULE_STATE_STDY
    *Oct 26 19:59:41.907: %SERVICEMODULE-2-IPCONFIGFAILED: Service module SM1/0 IP configuration (vlan default gateway) failed
    *Oct 26 20:00:23.287: %SM_INSTALL-6-INST_FAIL: SM1/0 is reset due to
    Can not download sre-v-k9.smv.1.0.0.35.pkg
    error code 0 : error type 'couldn't connect to host'.
    *Oct 26 20:00:23.287: %SRE_SM-6-STATE_CHANGE: SM1/0 changing state from SERVICE_MODULE_STATE_STDY to SERVICE_MODULE_STATE_ERRQ
    *Oct 26 20:00:23.287: %SM_INSTALL-6-INST_FAIL: SM1/0 is reset due to Unable to install. Please try again.


    Hi Ken,



    After you issue the install CLI from IOS, Can you session into the blade to capture the installation steps/logs. Please make sure you have all required files in your ftp server.



    Thanks,

    Ashwin



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Monday, October 25, 2010 5:18 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: Trouble installing SRE-V software



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    My config:

    interface SM1/0
    ip address 10.0.0.100 255.255.255.0
    service-module ip address 10.0.0.1 255.255.255.0
    service-module ip default-gateway 10.0.0.100
    service-module mgf ip address 1.10.10.5 255.255.255.0
    service-module mgf ip default-gateway 1.10.10.3
    !
    interface SM1/1
    description Internal switch interface connected to Service Module
    switchport mode trunk
    !
    interface Vlan1
    ip address 1.10.10.3 255.255.255.0
    !
    ip forward-protocol nd
    !
    ip http server
    ip http access-class 23
    ip http authentication local
    ip http secure-server
    ip http timeout-policy idle 60 life 86400 requests 10000
    !
    ip route 1.10.10.5 255.255.255.255 Vlan1

    Here is what I get when I try to install:

    Install of ftp://172.17.17.124/sre-v-k9.smv.1.0.0.35.pkg in progress
    Install status : File sre-v-k9.smv.1.0.0.35.pkg.install.sre requested
    Local Partition Info - (0 apps)
    =====================
    Retrieving partition information
    boxer#service-module sm 1/0 status
    Service Module is Cisco SM1/0
    Service Module supports session via TTY line 67
    Service Module is trying to recover from error
    Service Module heartbeat-reset is enabled
    Service Module is in fail open
    Service Module status is not available
    Module resource information:
    CPU Frequency: 1864 MHz
    Memory Size: 2535 MB
    Disk 0 Size: 500107 MB
    Disk 1 Size: 2055 MB
    Install of ftp://172.17.17.124/sre-v-k9.smv.1.0.0.35.pkg in progress
    Install status : File sre-v-k9.smv.1.0.0.35.pkg.install.sre requested
    Local Partition Info - (0 apps)
    =====================
    Retrieving partition information
    boxer#service-module sm 1/0 status
    Service Module is Cisco SM1/0
    Service Module supports session via TTY line 67
    Service Module is in Steady state
    Service Module heartbeat-reset is enabled
    Getting status from the Service Module, please wait..
    Cisco Foundation Software 1.0
    FNDN Running on SM
    Module resource information:
    CPU Frequency: 1862 MHz
    Memory Size: 4136636 MB
    Disk 0 Size: 953880 MB
    Install of ftp://172.17.17.124/sre-v-k9.smv.1.0.0.35.pkg in progress
    Install status : File sre-v-k9.smv.1.0.0.35.pkg.install.sre requested
    No local partition
    boxer#service-module sm 1/0 status
    Service Module is Cisco SM1/0
    Service Module supports session via TTY line 67
    Service Module is trying to recover from error
    Service Module heartbeat-reset is enabled
    Service Module status is not available
    Module resource information:
    CPU Frequency: 1862 MHz
    Memory Size: 4136636 MB
    Disk 0 Size: 953880 MB
    No install/uninstall in progress
    No local partition

    ---------------

    Any suggestons?
    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2678543>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2681319>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2688556>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2688752>
    or simply reply to this email.
    -- --
    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2692405>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2692542>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2692605>
    or simply reply to this email.
    -- --
    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2692674>
    or simply reply to this email.
    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2690720>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2690827>
    or simply reply to this email.





    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2690953>
    or simply reply to this email.

    Subject: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-
    Replied by: Ken Romo on 20-11-2010 01:34:34 AM
     
    Radhika,
     
     
    From the router

    Router# configure termina;

    Router(Config)#interface vlan 1

    Router(config-if) switchport mode trunk (THIS IS NOT AN OPTION FOR ME ON MY IOS FOR VLAN1)

    Router(config-if) end
    Thanks,
     Ken

    Subject: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-
    Replied by: Radhika Miriyala on 20-11-2010 01:34:34 AM
    Ken,

    Thanks for trying that out. I just checked another router here and with the image you are using I see that that cli is missing . I will check with the team.



    One last question is the ping from the router to the mgf address also triggering the crash?



    If we want to take a look at your setup would we be able to get access to it or could we do webex meeting where you can share your setup.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Thursday, October 28, 2010 2:42 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------

    Radhika,


    From the router

    Router# configure termina;

    Router(Config)#interface vlan 1

    Router(config-if) switchport mode trunk (THIS IS NOT AN OPTION FOR ME ON MY IOS FOR VLAN1)

    Router(config-if) end
    Thanks,
    Ken
    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2690977>
    or simply reply to this email.

    Subject: RE: New Message from Radhika Miriyala in Service Ready Engine Virtualizatio
    Replied by: Radhika Miriyala on 20-11-2010 01:34:34 AM
    Ken,

    Sorry I just realized the mistake. I meant to say make the interface sm 1/1 as trunk.

    Sorry about the confusion.



    Please try it out.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Thursday, October 28, 2010 2:50 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Radhika Miriyala in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Radhika Miriyala has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Ken,

    Thanks for trying that out. I just checked another router here and with the image you are using I see that that cli is missing . I will check with the team.



    One last question is the ping from the router to the mgf address also triggering the crash?



    If we want to take a look at your setup would we be able to get access to it or could we do webex meeting where you can share your setup.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Thursday, October 28, 2010 2:42 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------

    Radhika,


    From the router

    Router# configure termina;

    Router(Config)#interface vlan 1

    Router(config-if) switchport mode trunk (THIS IS NOT AN OPTION FOR ME ON MY IOS FOR VLAN1)

    Router(config-if) end
    Thanks,
    Ken
    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2690977>
    or simply reply to this email.
    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2692864>
    or simply reply to this email.

    Subject: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-
    Replied by: Ken Romo on 20-11-2010 01:34:34 AM
    Ken,

    Thanks for trying that out. I just checked another router here and with the image you are using I see that that cli is missing . I will check with the team.



    One last question is the ping from the router to the mgf address also triggering the crash?
     
    Nope that ping is good.


    If we want to take a look at your setup would we be able to get access to it or could we do webex meeting where you can share your setup.
     
    Would have to do Webex, we do not have DMZ or public network (that would be great if you could take a look)



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Thursday, October 28, 2010 2:42 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------

    Radhika,


    From the router

    Router# configure termina;

    Router(Config)#interface vlan 1

    Router(config-if) switchport mode trunk (THIS IS NOT AN OPTION FOR ME ON MY IOS FOR VLAN1)

    Router(config-if) end
    Thanks,
    Ken
    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2690977>
    or simply reply to this email.


    Subject: RE: New Message from Radhika Miriyala in Service Ready Engine Virtualizatio
    Replied by: Ken Romo on 20-11-2010 01:34:34 AM
    Radhika,
     
    No worries, we are trying to work this out together and I appreciate the help.
    s/m 1/1 is set as trunk but I went ahead and reconfigured to truank again and reloaded OS and get the same crash when I ping to the MGF interface from the SRE (I attached the errors at the bottom of this message).
     
    Ken,

    Sorry I just realized the mistake. I meant to say make the interface sm 1/1 as trunk.

    Sorry about the confusion.



    Please try it out.



    Thanks,

    Radhika



    boxer#
    %ALIGN-1-FATAL: Illegal access to a low address 22:02:10 UTC Thu Oct 28 2010
     addr=0x14, pc=0x22765BD8z , ra=0x22765B84z , sp=0x3022FBB8
    %ALIGN-1-FATAL: Illegal access to a low address 22:02:11 UTC Thu Oct 28 2010
     addr=0x14, pc=0x22765BD8z , ra=0x22765B84z , sp=0x3022FBB8

     22:02:11 UTC Thu Oct 28 2010: TLB (store) exception, CPU signal 10, PC = 0x22768478
     
    --------------------------------------------------------------------
       Possible software fault. Upon reccurence, please collect
       crashinfo, "show tech" and contact Cisco Technical Support.
    --------------------------------------------------------------------

    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z
    $0 : 00000000 00000000, AT : 00000000 29130000, v0 : 00000000 00000001, v1 : 00000000 0D8B8540
    a0 : 00000000 00000000, a1 : 00000000 0D8B8584, a2 : 00000000 2A2F8ABC, a3 : 00000000 00000004
    t0 : 00000000 00000020, t1 : 00000000 500099E1, t2 : 00000000 500081E0, t3 : FFFFFFFF FFFFFFF2
    t4 : 00000000 0000000E, t5 : 00000000 00000000, t6 : 00000000 0D95F890, t7 : 00000000 000001FF
    s0 : 00000000 00000000, s1 : 00000000 2A2FDB40, s2 : FFFFFFFF FFFFFFEC, s3 : 00000000 3080C980
    s4 : 00000000 0D95F89E, s5 : 00000000 2A300EE0, s6 : 00000000 00000000, s7 : 00000000 0000000E
    t8 : 00000000 000007FC, t9 : 00000000 2A300200, k0 : 00000000 00000000, k1 : 00000000 00000000
    gp : 00000000 29133C00, sp : 00000000 3022FBB8, s8 : 00000000 00000054, ra : 00000000 22768424
    EPC  : 22768478, ErrorEPC : 80412AB4, SREG     : 500099E3
    MDLO : 87126668, MDHI     : D990ADBB, BadVaddr : 00000014
    CacheErr_Icache : 0x007F7F00 - 000040D8, CacheErr_Dcache : 0x00000000 - 00001FA0
    TagLo_Icache : 0x00000000 - 23642303, DataLo_Icache : 0xAFBF0018 - 0D81ADDB
    DataHi_Icache: 0x00000000 - 00000001
    TagLo_Dcache : 0x00000000 - 2277E583, TagHi_Dcache : 0x00000000 - 0912BD81
    DataLo_Dcache: 0x00000001 - 2368110C, DataHi_Dcache : 0x00000000 - 0000001C
    TEXT_START : 0x21003178
    DATA_START : 0x260888A0
    Cause 0000040C (Code 0x3): TLB (store) exception

     22:02:11 UTC Thu Oct 28 2010: TLB (store) exception, CPU signal 10, PC = 0x22768478
     
    --------------------------------------------------------------------
       Possible software fault. Upon reccurence, please collect
       crashinfo, "show tech" and contact Cisco Technical Support.
    --------------------------------------------------------------------

    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z
    $0 : 00000000 00000000, AT : 00000000 29130000, v0 : 00000000 00000001, v1 : 00000000 0D8B8540
    a0 : 00000000 00000000, a1 : 00000000 0D8B8584, a2 : 00000000 2A2F8ABC, a3 : 00000000 00000004
    t0 : 00000000 00000020, t1 : 00000000 500099E1, t2 : 00000000 500081E0, t3 : FFFFFFFF FFFFFFF2
    t4 : 00000000 0000000E, t5 : 00000000 00000000, t6 : 00000000 0D95F890, t7 : 00000000 000001FF
    s0 : 00000000 00000000, s1 : 00000000 2A2FDB40, s2 : FFFFFFFF FFFFFFEC, s3 : 00000000 3080C980
    s4 : 00000000 0D95F89E, s5 : 00000000 2A300EE0, s6 : 00000000 00000000, s7 : 00000000 0000000E
    t8 : 00000000 000007FC, t9 : 00000000 2A300200, k0 : 00000000 00000000, k1 : 00000000 00000000
    gp : 00000000 29133C00, sp : 00000000 3022FBB8, s8 : 00000000 00000054, ra : 00000000 22768424
    EPC  : 22768478, ErrorEPC : 80412AB4, SREG     : 500099E3
    MDLO : 87126668, MDHI     : D990ADBB, BadVaddr : 00000014
    CacheErr_Icache : 0x007F7F00 - 000040D8, CacheErr_Dcache : 0x00000000 - 00001FA0
    TagLo_Icache : 0x00000000 - 23642303, DataLo_Icache : 0xAFBF0018 - 0D81ADDB
    DataHi_Icache: 0x00000000 - 00000001
    TagLo_Dcache : 0x00000000 - 2277E583, TagHi_Dcache : 0x00000000 - 0912BD81
    DataLo_Dcache: 0x00000001 - 2368110C, DataHi_Dcache : 0x00000000 - 0000001C
    TEXT_START : 0x21003178
    DATA_START : 0x260888A0
    Cause 0000040C (Code 0x3): TLB (store) exception
    Writing crashinfo to flash:crashinfo_20101028-220211-UTC
     22:02:11 UTC Thu Oct 28 2010: TLB (store) exception, CPU signal 10, PC = 0x22768478
     
    --------------------------------------------------------------------
       Possible software fault. Upon reccurence, please collect
       crashinfo, "show tech" and contact Cisco Technical Support.
    --------------------------------------------------------------------

    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z
    $0 : 00000000 00000000, AT : 00000000 29130000, v0 : 00000000 00000001, v1 : 00000000 0D8B8540
    a0 : 00000000 00000000, a1 : 00000000 0D8B8584, a2 : 00000000 2A2F8ABC, a3 : 00000000 00000004
    t0 : 00000000 00000020, t1 : 00000000 500099E1, t2 : 00000000 500081E0, t3 : FFFFFFFF FFFFFFF2
    t4 : 00000000 0000000E, t5 : 00000000 00000000, t6 : 00000000 0D95F890, t7 : 00000000 000001FF
    s0 : 00000000 00000000, s1 : 00000000 2A2FDB40, s2 : FFFFFFFF FFFFFFEC, s3 : 00000000 3080C980
    s4 : 00000000 0D95F89E, s5 : 00000000 2A300EE0, s6 : 00000000 00000000, s7 : 00000000 0000000E
    t8 : 00000000 000007FC, t9 : 00000000 2A300200, k0 : 00000000 00000000, k1 : 00000000 00000000
    gp : 00000000 29133C00, sp : 00000000 3022FBB8, s8 : 00000000 00000054, ra : 00000000 22768424
    EPC  : 22768478, ErrorEPC : 80412AB4, SREG     : 500099E3
    MDLO : 87126668, MDHI     : D990ADBB, BadVaddr : 00000014
    CacheErr_Icache : 0x007F7F00 - 000040D8, CacheErr_Dcache : 0x00000000 - 00001FA0
    TagLo_Icache : 0x00000000 - 23642303, DataLo_Icache : 0xAFBF0018 - 0D81ADDB
    DataHi_Icache: 0x00000000 - 00000001
    TagLo_Dcache : 0x00000000 - 2277E583, TagHi_Dcache : 0x00000000 - 0912BD81
    DataLo_Dcache: 0x00000001 - 2368110C, DataHi_Dcache : 0x00000000 - 0000001C
    TEXT_START : 0x21003178
    DATA_START : 0x260888A0
    Cause 0000040C (Code 0x3): TLB (store) exception
    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z

    === Flushing messages (22:02:12 UTC Thu Oct 28 2010) ===
    Buffered messages:
    *Oct 28 20:52:40.075: %LINK-3-UPDOWN: Interface SM1/0, changed state to up
    *Oct 28 20:52:42.195: %LINK-3-UPDOWN: Interface GigabitEthernet0/0, changed state to up
    *Oct 28 20:52:42.195: %LINK-3-UPDOWN: Interface GigabitEthernet0/1, changed state to down
    *Oct 28 20:52:42.195: %LINK-3-UPDOWN: Interface GigabitEthernet0/2, changed state to down
    *Oct 28 20:52:44.631: %LINK-3-UPDOWN: Interface SM1/1, changed state to up
    *Oct 28 20:53:01.655: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/0, changed state to up
    *Oct 28 20:53:01.923: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/1, changed state to up
    *Oct 28 20:53:02.075: %LINK-3-UPDOWN: Interface Foreign Exchange Station 0/1/0, changed state to up
    *Oct 28 20:53:02.075: %LINK-3-UPDOWN: Interface Foreign Exchange Station 0/1/1, changed state to up
    *Oct 28 20:53:43.739: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/0, changed state to operational status down due to cable removal
    *Oct 28 20:53:44.739: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/1, changed state to operational status down due to cable removal
    Queued messages:
    No warm reboot Storage
    *** System received a Bus Error exception ***
    signal= 0xa, code= 0x40c, context= 0x29726b74
      PC = 0x22768478, SP = 0x3022fbb8, RA = 0x22768424
      Cause Reg = 0x0000040c, Status Reg = 0x500099e3
    System Bootstrap, Version 15.0(1r)M6, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 2010 by cisco Systems, Inc.
    Total memory size = 512 MB - On-board = 512 MB, DIMM0 = 0 MB
    CISCO2911/K9 platform with 524288 Kbytes of main memory
    Main memory is configured to 72/-1(On-board/DIMM0) bit mode with ECC enabled

    Readonly ROMMON initialized
    program load complete, entry point: 0x80803000, size: 0x1b340

    IOS Image Load Test
    ___________________
    Digitally Signed Development Software
    program load complete, entry point: 0x81000000, size: 0x40b6b74
    Self decompressing the image : #############################################################################################################
     

    Subject: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-
    Replied by: Radhika Miriyala on 20-11-2010 01:34:34 AM
    Ken,

    Would a webex session tomorrow morning (any time between 10:00 and 1:00) work for you? Let me know the time that would work for you and also your email address so I can send you a webex invite.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Thursday, October 28, 2010 3:12 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Radhika Miriyala in Service Ready Engine Virtualizatio



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    No worries, we are trying to work this out together and I appreciate the help.
    s/m 1/1 is set as trunk but I went ahead and reconfigured to truank again and reloaded OS and get the same crash when I ping to the MGF interface from the SRE (I attached the errors at the bottom of this message).

    Ken,

    Sorry I just realized the mistake. I meant to say make the interface sm 1/1 as trunk.

    Sorry about the confusion.



    Please try it out.



    Thanks,

    Radhika



    boxer#
    %ALIGN-1-FATAL: Illegal access to a low address 22:02:10 UTC Thu Oct 28 2010
    addr=0x14, pc=0x22765BD8z , ra=0x22765B84z , sp=0x3022FBB8
    %ALIGN-1-FATAL: Illegal access to a low address 22:02:11 UTC Thu Oct 28 2010
    addr=0x14, pc=0x22765BD8z , ra=0x22765B84z , sp=0x3022FBB8

    22:02:11 UTC Thu Oct 28 2010: TLB (store) exception, CPU signal 10, PC = 0x22768478

    --------------------------------------------------------------------
       Possible software fault. Upon reccurence, please collect
       crashinfo, "show tech" and contact Cisco Technical Support.
    --------------------------------------------------------------------

    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z
    $0 : 00000000 00000000, AT : 00000000 29130000, v0 : 00000000 00000001, v1 : 00000000 0D8B8540
    a0 : 00000000 00000000, a1 : 00000000 0D8B8584, a2 : 00000000 2A2F8ABC, a3 : 00000000 00000004
    t0 : 00000000 00000020, t1 : 00000000 500099E1, t2 : 00000000 500081E0, t3 : FFFFFFFF FFFFFFF2
    t4 : 00000000 0000000E, t5 : 00000000 00000000, t6 : 00000000 0D95F890, t7 : 00000000 000001FF
    s0 : 00000000 00000000, s1 : 00000000 2A2FDB40, s2 : FFFFFFFF FFFFFFEC, s3 : 00000000 3080C980
    s4 : 00000000 0D95F89E, s5 : 00000000 2A300EE0, s6 : 00000000 00000000, s7 : 00000000 0000000E
    t8 : 00000000 000007FC, t9 : 00000000 2A300200, k0 : 00000000 00000000, k1 : 00000000 00000000
    gp : 00000000 29133C00, sp : 00000000 3022FBB8, s8 : 00000000 00000054, ra : 00000000 22768424
    EPC  : 22768478, ErrorEPC : 80412AB4, SREG     : 500099E3
    MDLO : 87126668, MDHI     : D990ADBB, BadVaddr : 00000014
    CacheErr_Icache : 0x007F7F00 - 000040D8, CacheErr_Dcache : 0x00000000 - 00001FA0
    TagLo_Icache : 0x00000000 - 23642303, DataLo_Icache : 0xAFBF0018 - 0D81ADDB
    DataHi_Icache: 0x00000000 - 00000001
    TagLo_Dcache : 0x00000000 - 2277E583, TagHi_Dcache : 0x00000000 - 0912BD81
    DataLo_Dcache: 0x00000001 - 2368110C, DataHi_Dcache : 0x00000000 - 0000001C
    TEXT_START : 0x21003178
    DATA_START : 0x260888A0
    Cause 0000040C (Code 0x3): TLB (store) exception

    22:02:11 UTC Thu Oct 28 2010: TLB (store) exception, CPU signal 10, PC = 0x22768478

    --------------------------------------------------------------------
       Possible software fault. Upon reccurence, please collect
       crashinfo, "show tech" and contact Cisco Technical Support.
    --------------------------------------------------------------------

    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z
    $0 : 00000000 00000000, AT : 00000000 29130000, v0 : 00000000 00000001, v1 : 00000000 0D8B8540
    a0 : 00000000 00000000, a1 : 00000000 0D8B8584, a2 : 00000000 2A2F8ABC, a3 : 00000000 00000004
    t0 : 00000000 00000020, t1 : 00000000 500099E1, t2 : 00000000 500081E0, t3 : FFFFFFFF FFFFFFF2
    t4 : 00000000 0000000E, t5 : 00000000 00000000, t6 : 00000000 0D95F890, t7 : 00000000 000001FF
    s0 : 00000000 00000000, s1 : 00000000 2A2FDB40, s2 : FFFFFFFF FFFFFFEC, s3 : 00000000 3080C980
    s4 : 00000000 0D95F89E, s5 : 00000000 2A300EE0, s6 : 00000000 00000000, s7 : 00000000 0000000E
    t8 : 00000000 000007FC, t9 : 00000000 2A300200, k0 : 00000000 00000000, k1 : 00000000 00000000
    gp : 00000000 29133C00, sp : 00000000 3022FBB8, s8 : 00000000 00000054, ra : 00000000 22768424
    EPC  : 22768478, ErrorEPC : 80412AB4, SREG     : 500099E3
    MDLO : 87126668, MDHI     : D990ADBB, BadVaddr : 00000014
    CacheErr_Icache : 0x007F7F00 - 000040D8, CacheErr_Dcache : 0x00000000 - 00001FA0
    TagLo_Icache : 0x00000000 - 23642303, DataLo_Icache : 0xAFBF0018 - 0D81ADDB
    DataHi_Icache: 0x00000000 - 00000001
    TagLo_Dcache : 0x00000000 - 2277E583, TagHi_Dcache : 0x00000000 - 0912BD81
    DataLo_Dcache: 0x00000001 - 2368110C, DataHi_Dcache : 0x00000000 - 0000001C
    TEXT_START : 0x21003178
    DATA_START : 0x260888A0
    Cause 0000040C (Code 0x3): TLB (store) exception
    Writing crashinfo to flash:crashinfo_20101028-220211-UTC
    22:02:11 UTC Thu Oct 28 2010: TLB (store) exception, CPU signal 10, PC = 0x22768478

    --------------------------------------------------------------------
       Possible software fault. Upon reccurence, please collect
       crashinfo, "show tech" and contact Cisco Technical Support.
    --------------------------------------------------------------------

    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z
    $0 : 00000000 00000000, AT : 00000000 29130000, v0 : 00000000 00000001, v1 : 00000000 0D8B8540
    a0 : 00000000 00000000, a1 : 00000000 0D8B8584, a2 : 00000000 2A2F8ABC, a3 : 00000000 00000004
    t0 : 00000000 00000020, t1 : 00000000 500099E1, t2 : 00000000 500081E0, t3 : FFFFFFFF FFFFFFF2
    t4 : 00000000 0000000E, t5 : 00000000 00000000, t6 : 00000000 0D95F890, t7 : 00000000 000001FF
    s0 : 00000000 00000000, s1 : 00000000 2A2FDB40, s2 : FFFFFFFF FFFFFFEC, s3 : 00000000 3080C980
    s4 : 00000000 0D95F89E, s5 : 00000000 2A300EE0, s6 : 00000000 00000000, s7 : 00000000 0000000E
    t8 : 00000000 000007FC, t9 : 00000000 2A300200, k0 : 00000000 00000000, k1 : 00000000 00000000
    gp : 00000000 29133C00, sp : 00000000 3022FBB8, s8 : 00000000 00000054, ra : 00000000 22768424
    EPC  : 22768478, ErrorEPC : 80412AB4, SREG     : 500099E3
    MDLO : 87126668, MDHI     : D990ADBB, BadVaddr : 00000014
    CacheErr_Icache : 0x007F7F00 - 000040D8, CacheErr_Dcache : 0x00000000 - 00001FA0
    TagLo_Icache : 0x00000000 - 23642303, DataLo_Icache : 0xAFBF0018 - 0D81ADDB
    DataHi_Icache: 0x00000000 - 00000001
    TagLo_Dcache : 0x00000000 - 2277E583, TagHi_Dcache : 0x00000000 - 0912BD81
    DataLo_Dcache: 0x00000001 - 2368110C, DataHi_Dcache : 0x00000000 - 0000001C
    TEXT_START : 0x21003178
    DATA_START : 0x260888A0
    Cause 0000040C (Code 0x3): TLB (store) exception
    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z

    === Flushing messages (22:02:12 UTC Thu Oct 28 2010) ===
    Buffered messages:
    *Oct 28 20:52:40.075: %LINK-3-UPDOWN: Interface SM1/0, changed state to up
    *Oct 28 20:52:42.195: %LINK-3-UPDOWN: Interface GigabitEthernet0/0, changed state to up
    *Oct 28 20:52:42.195: %LINK-3-UPDOWN: Interface GigabitEthernet0/1, changed state to down
    *Oct 28 20:52:42.195: %LINK-3-UPDOWN: Interface GigabitEthernet0/2, changed state to down
    *Oct 28 20:52:44.631: %LINK-3-UPDOWN: Interface SM1/1, changed state to up
    *Oct 28 20:53:01.655: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/0, changed state to up
    *Oct 28 20:53:01.923: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/1, changed state to up
    *Oct 28 20:53:02.075: %LINK-3-UPDOWN: Interface Foreign Exchange Station 0/1/0, changed state to up
    *Oct 28 20:53:02.075: %LINK-3-UPDOWN: Interface Foreign Exchange Station 0/1/1, changed state to up
    *Oct 28 20:53:43.739: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/0, changed state to operational status down due to cable removal
    *Oct 28 20:53:44.739: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/1, changed state to operational status down due to cable removal
    Queued messages:
    No warm reboot Storage
    *** System received a Bus Error exception ***
    signal= 0xa, code= 0x40c, context= 0x29726b74
      PC = 0x22768478, SP = 0x3022fbb8, RA = 0x22768424
      Cause Reg = 0x0000040c, Status Reg = 0x500099e3
    System Bootstrap, Version 15.0(1r)M6, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 2010 by cisco Systems, Inc.
    Total memory size = 512 MB - On-board = 512 MB, DIMM0 = 0 MB
    CISCO2911/K9 platform with 524288 Kbytes of main memory
    Main memory is configured to 72/-1(On-board/DIMM0) bit mode with ECC enabled

    Readonly ROMMON initialized
    program load complete, entry point: 0x80803000, size: 0x1b340

    IOS Image Load Test
    ___________________
    Digitally Signed Development Software
    program load complete, entry point: 0x81000000, size: 0x40b6b74
    Self decompressing the image : #############################################################################################################

    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2691036>
    or simply reply to this email.

    Subject: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-
    Replied by: Ken Romo on 20-11-2010 01:34:35 AM
    Radhika,
     
    I will work around your schedule, anytime you are available, I will make myself available.
    email:
    kromo@opentext.com
     
    Thanks in advance,
     
    Ken Romo
     
    +++++++++++++++++++++++++++++++++
     
    Ken,

    Would a webex session tomorrow morning (any time between 10:00 and 1:00) work for you? Let me know the time that would work for you and also your email address so I can send you a webex invite.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Thursday, October 28, 2010 3:12 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Radhika Miriyala in Service Ready Engine Virtualizatio



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    No worries, we are trying to work this out together and I appreciate the help.
    s/m 1/1 is set as trunk but I went ahead and reconfigured to truank again and reloaded OS and get the same crash when I ping to the MGF interface from the SRE (I attached the errors at the bottom of this message).

    Ken,

    Sorry I just realized the mistake. I meant to say make the interface sm 1/1 as trunk.

    Sorry about the confusion.



    Please try it out.



    Thanks,

    Radhika



    boxer#
    %ALIGN-1-FATAL: Illegal access to a low address 22:02:10 UTC Thu Oct 28 2010
    addr=0x14, pc=0x22765BD8z , ra=0x22765B84z , sp=0x3022FBB8
    %ALIGN-1-FATAL: Illegal access to a low address 22:02:11 UTC Thu Oct 28 2010
    addr=0x14, pc=0x22765BD8z , ra=0x22765B84z , sp=0x3022FBB8

    22:02:11 UTC Thu Oct 28 2010: TLB (store) exception, CPU signal 10, PC = 0x22768478

    --------------------------------------------------------------------
    Possible software fault. Upon reccurence, please collect
    crashinfo, "show tech" and contact Cisco Technical Support.
    --------------------------------------------------------------------

    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z
    $0 : 00000000 00000000, AT : 00000000 29130000, v0 : 00000000 00000001, v1 : 00000000 0D8B8540
    a0 : 00000000 00000000, a1 : 00000000 0D8B8584, a2 : 00000000 2A2F8ABC, a3 : 00000000 00000004
    t0 : 00000000 00000020, t1 : 00000000 500099E1, t2 : 00000000 500081E0, t3 : FFFFFFFF FFFFFFF2
    t4 : 00000000 0000000E, t5 : 00000000 00000000, t6 : 00000000 0D95F890, t7 : 00000000 000001FF
    s0 : 00000000 00000000, s1 : 00000000 2A2FDB40, s2 : FFFFFFFF FFFFFFEC, s3 : 00000000 3080C980
    s4 : 00000000 0D95F89E, s5 : 00000000 2A300EE0, s6 : 00000000 00000000, s7 : 00000000 0000000E
    t8 : 00000000 000007FC, t9 : 00000000 2A300200, k0 : 00000000 00000000, k1 : 00000000 00000000
    gp : 00000000 29133C00, sp : 00000000 3022FBB8, s8 : 00000000 00000054, ra : 00000000 22768424
    EPC : 22768478, ErrorEPC : 80412AB4, SREG : 500099E3
    MDLO : 87126668, MDHI : D990ADBB, BadVaddr : 00000014
    CacheErr_Icache : 0x007F7F00 - 000040D8, CacheErr_Dcache : 0x00000000 - 00001FA0
    TagLo_Icache : 0x00000000 - 23642303, DataLo_Icache : 0xAFBF0018 - 0D81ADDB
    DataHi_Icache: 0x00000000 - 00000001
    TagLo_Dcache : 0x00000000 - 2277E583, TagHi_Dcache : 0x00000000 - 0912BD81
    DataLo_Dcache: 0x00000001 - 2368110C, DataHi_Dcache : 0x00000000 - 0000001C
    TEXT_START : 0x21003178
    DATA_START : 0x260888A0
    Cause 0000040C (Code 0x3): TLB (store) exception

    22:02:11 UTC Thu Oct 28 2010: TLB (store) exception, CPU signal 10, PC = 0x22768478

    --------------------------------------------------------------------
    Possible software fault. Upon reccurence, please collect
    crashinfo, "show tech" and contact Cisco Technical Support.
    --------------------------------------------------------------------

    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z
    $0 : 00000000 00000000, AT : 00000000 29130000, v0 : 00000000 00000001, v1 : 00000000 0D8B8540
    a0 : 00000000 00000000, a1 : 00000000 0D8B8584, a2 : 00000000 2A2F8ABC, a3 : 00000000 00000004
    t0 : 00000000 00000020, t1 : 00000000 500099E1, t2 : 00000000 500081E0, t3 : FFFFFFFF FFFFFFF2
    t4 : 00000000 0000000E, t5 : 00000000 00000000, t6 : 00000000 0D95F890, t7 : 00000000 000001FF
    s0 : 00000000 00000000, s1 : 00000000 2A2FDB40, s2 : FFFFFFFF FFFFFFEC, s3 : 00000000 3080C980
    s4 : 00000000 0D95F89E, s5 : 00000000 2A300EE0, s6 : 00000000 00000000, s7 : 00000000 0000000E
    t8 : 00000000 000007FC, t9 : 00000000 2A300200, k0 : 00000000 00000000, k1 : 00000000 00000000
    gp : 00000000 29133C00, sp : 00000000 3022FBB8, s8 : 00000000 00000054, ra : 00000000 22768424
    EPC : 22768478, ErrorEPC : 80412AB4, SREG : 500099E3
    MDLO : 87126668, MDHI : D990ADBB, BadVaddr : 00000014
    CacheErr_Icache : 0x007F7F00 - 000040D8, CacheErr_Dcache : 0x00000000 - 00001FA0
    TagLo_Icache : 0x00000000 - 23642303, DataLo_Icache : 0xAFBF0018 - 0D81ADDB
    DataHi_Icache: 0x00000000 - 00000001
    TagLo_Dcache : 0x00000000 - 2277E583, TagHi_Dcache : 0x00000000 - 0912BD81
    DataLo_Dcache: 0x00000001 - 2368110C, DataHi_Dcache : 0x00000000 - 0000001C
    TEXT_START : 0x21003178
    DATA_START : 0x260888A0
    Cause 0000040C (Code 0x3): TLB (store) exception
    Writing crashinfo to flash:crashinfo_20101028-220211-UTC
    22:02:11 UTC Thu Oct 28 2010: TLB (store) exception, CPU signal 10, PC = 0x22768478

    --------------------------------------------------------------------
    Possible software fault. Upon reccurence, please collect
    crashinfo, "show tech" and contact Cisco Technical Support.
    --------------------------------------------------------------------

    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z
    $0 : 00000000 00000000, AT : 00000000 29130000, v0 : 00000000 00000001, v1 : 00000000 0D8B8540
    a0 : 00000000 00000000, a1 : 00000000 0D8B8584, a2 : 00000000 2A2F8ABC, a3 : 00000000 00000004
    t0 : 00000000 00000020, t1 : 00000000 500099E1, t2 : 00000000 500081E0, t3 : FFFFFFFF FFFFFFF2
    t4 : 00000000 0000000E, t5 : 00000000 00000000, t6 : 00000000 0D95F890, t7 : 00000000 000001FF
    s0 : 00000000 00000000, s1 : 00000000 2A2FDB40, s2 : FFFFFFFF FFFFFFEC, s3 : 00000000 3080C980
    s4 : 00000000 0D95F89E, s5 : 00000000 2A300EE0, s6 : 00000000 00000000, s7 : 00000000 0000000E
    t8 : 00000000 000007FC, t9 : 00000000 2A300200, k0 : 00000000 00000000, k1 : 00000000 00000000
    gp : 00000000 29133C00, sp : 00000000 3022FBB8, s8 : 00000000 00000054, ra : 00000000 22768424
    EPC : 22768478, ErrorEPC : 80412AB4, SREG : 500099E3
    MDLO : 87126668, MDHI : D990ADBB, BadVaddr : 00000014
    CacheErr_Icache : 0x007F7F00 - 000040D8, CacheErr_Dcache : 0x00000000 - 00001FA0
    TagLo_Icache : 0x00000000 - 23642303, DataLo_Icache : 0xAFBF0018 - 0D81ADDB
    DataHi_Icache: 0x00000000 - 00000001
    TagLo_Dcache : 0x00000000 - 2277E583, TagHi_Dcache : 0x00000000 - 0912BD81
    DataLo_Dcache: 0x00000001 - 2368110C, DataHi_Dcache : 0x00000000 - 0000001C
    TEXT_START : 0x21003178
    DATA_START : 0x260888A0
    Cause 0000040C (Code 0x3): TLB (store) exception
    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z

    === Flushing messages (22:02:12 UTC Thu Oct 28 2010) ===
    Buffered messages:
    *Oct 28 20:52:40.075: %LINK-3-UPDOWN: Interface SM1/0, changed state to up
    *Oct 28 20:52:42.195: %LINK-3-UPDOWN: Interface GigabitEthernet0/0, changed state to up
    *Oct 28 20:52:42.195: %LINK-3-UPDOWN: Interface GigabitEthernet0/1, changed state to down
    *Oct 28 20:52:42.195: %LINK-3-UPDOWN: Interface GigabitEthernet0/2, changed state to down
    *Oct 28 20:52:44.631: %LINK-3-UPDOWN: Interface SM1/1, changed state to up
    *Oct 28 20:53:01.655: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/0, changed state to up
    *Oct 28 20:53:01.923: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/1, changed state to up
    *Oct 28 20:53:02.075: %LINK-3-UPDOWN: Interface Foreign Exchange Station 0/1/0, changed state to up
    *Oct 28 20:53:02.075: %LINK-3-UPDOWN: Interface Foreign Exchange Station 0/1/1, changed state to up
    *Oct 28 20:53:43.739: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/0, changed state to operational status down due to cable removal
    *Oct 28 20:53:44.739: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/1, changed state to operational status down due to cable removal
    Queued messages:
    No warm reboot Storage
    *** System received a Bus Error exception ***
    signal= 0xa, code= 0x40c, context= 0x29726b74
    PC = 0x22768478, SP = 0x3022fbb8, RA = 0x22768424
    Cause Reg = 0x0000040c, Status Reg = 0x500099e3
    System Bootstrap, Version 15.0(1r)M6, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 2010 by cisco Systems, Inc.
    Total memory size = 512 MB - On-board = 512 MB, DIMM0 = 0 MB
    CISCO2911/K9 platform with 524288 Kbytes of main memory
    Main memory is configured to 72/-1(On-board/DIMM0) bit mode with ECC enabled

    Readonly ROMMON initialized
    program load complete, entry point: 0x80803000, size: 0x1b340

    IOS Image Load Test
    ___________________
    Digitally Signed Development Software
    program load complete, entry point: 0x81000000, size: 0x40b6b74
    Self decompressing the image : #############################################################################################################

    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2691036>
    or simply reply to this email.


    Subject: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-
    Replied by: Radhika Miriyala on 20-11-2010 01:34:35 AM
    Ken,

    I am trying to get some help from the IOS team since this a router crash.  So I will setup the webex session to debug for some time Monday so we can collect all the information and try out any suggestion from them.



    For Now We will post a newer IOS image to the beta Site and can you give that a try to see if that will solve the issue.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Friday, October 29, 2010 8:24 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    I will work around your schedule, anytime you are available, I will make myself available.
    email:
    kromo@opentext.com

    Thanks in advance,

    Ken Romo

    +++++++++++++++++++++++++++++++++

    Ken,

    Would a webex session tomorrow morning (any time between 10:00 and 1:00) work for you? Let me know the time that would work for you and also your email address so I can send you a webex invite.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Thursday, October 28, 2010 3:12 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Radhika Miriyala in Service Ready Engine Virtualizatio



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    No worries, we are trying to work this out together and I appreciate the help.
    s/m 1/1 is set as trunk but I went ahead and reconfigured to truank again and reloaded OS and get the same crash when I ping to the MGF interface from the SRE (I attached the errors at the bottom of this message).

    Ken,

    Sorry I just realized the mistake. I meant to say make the interface sm 1/1 as trunk.

    Sorry about the confusion.



    Please try it out.



    Thanks,

    Radhika



    boxer#
    %ALIGN-1-FATAL: Illegal access to a low address 22:02:10 UTC Thu Oct 28 2010
    addr=0x14, pc=0x22765BD8z , ra=0x22765B84z , sp=0x3022FBB8
    %ALIGN-1-FATAL: Illegal access to a low address 22:02:11 UTC Thu Oct 28 2010
    addr=0x14, pc=0x22765BD8z , ra=0x22765B84z , sp=0x3022FBB8

    22:02:11 UTC Thu Oct 28 2010: TLB (store) exception, CPU signal 10, PC = 0x22768478

    --------------------------------------------------------------------
    Possible software fault. Upon reccurence, please collect
    crashinfo, "show tech" and contact Cisco Technical Support.
    --------------------------------------------------------------------

    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z
    $0 : 00000000 00000000, AT : 00000000 29130000, v0 : 00000000 00000001, v1 : 00000000 0D8B8540
    a0 : 00000000 00000000, a1 : 00000000 0D8B8584, a2 : 00000000 2A2F8ABC, a3 : 00000000 00000004
    t0 : 00000000 00000020, t1 : 00000000 500099E1, t2 : 00000000 500081E0, t3 : FFFFFFFF FFFFFFF2
    t4 : 00000000 0000000E, t5 : 00000000 00000000, t6 : 00000000 0D95F890, t7 : 00000000 000001FF
    s0 : 00000000 00000000, s1 : 00000000 2A2FDB40, s2 : FFFFFFFF FFFFFFEC, s3 : 00000000 3080C980
    s4 : 00000000 0D95F89E, s5 : 00000000 2A300EE0, s6 : 00000000 00000000, s7 : 00000000 0000000E
    t8 : 00000000 000007FC, t9 : 00000000 2A300200, k0 : 00000000 00000000, k1 : 00000000 00000000
    gp : 00000000 29133C00, sp : 00000000 3022FBB8, s8 : 00000000 00000054, ra : 00000000 22768424
    EPC : 22768478, ErrorEPC : 80412AB4, SREG : 500099E3
    MDLO : 87126668, MDHI : D990ADBB, BadVaddr : 00000014
    CacheErr_Icache : 0x007F7F00 - 000040D8, CacheErr_Dcache : 0x00000000 - 00001FA0
    TagLo_Icache : 0x00000000 - 23642303, DataLo_Icache : 0xAFBF0018 - 0D81ADDB
    DataHi_Icache: 0x00000000 - 00000001
    TagLo_Dcache : 0x00000000 - 2277E583, TagHi_Dcache : 0x00000000 - 0912BD81
    DataLo_Dcache: 0x00000001 - 2368110C, DataHi_Dcache : 0x00000000 - 0000001C
    TEXT_START : 0x21003178
    DATA_START : 0x260888A0
    Cause 0000040C (Code 0x3): TLB (store) exception

    22:02:11 UTC Thu Oct 28 2010: TLB (store) exception, CPU signal 10, PC = 0x22768478

    --------------------------------------------------------------------
    Possible software fault. Upon reccurence, please collect
    crashinfo, "show tech" and contact Cisco Technical Support.
    --------------------------------------------------------------------

    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z
    $0 : 00000000 00000000, AT : 00000000 29130000, v0 : 00000000 00000001, v1 : 00000000 0D8B8540
    a0 : 00000000 00000000, a1 : 00000000 0D8B8584, a2 : 00000000 2A2F8ABC, a3 : 00000000 00000004
    t0 : 00000000 00000020, t1 : 00000000 500099E1, t2 : 00000000 500081E0, t3 : FFFFFFFF FFFFFFF2
    t4 : 00000000 0000000E, t5 : 00000000 00000000, t6 : 00000000 0D95F890, t7 : 00000000 000001FF
    s0 : 00000000 00000000, s1 : 00000000 2A2FDB40, s2 : FFFFFFFF FFFFFFEC, s3 : 00000000 3080C980
    s4 : 00000000 0D95F89E, s5 : 00000000 2A300EE0, s6 : 00000000 00000000, s7 : 00000000 0000000E
    t8 : 00000000 000007FC, t9 : 00000000 2A300200, k0 : 00000000 00000000, k1 : 00000000 00000000
    gp : 00000000 29133C00, sp : 00000000 3022FBB8, s8 : 00000000 00000054, ra : 00000000 22768424
    EPC : 22768478, ErrorEPC : 80412AB4, SREG : 500099E3
    MDLO : 87126668, MDHI : D990ADBB, BadVaddr : 00000014
    CacheErr_Icache : 0x007F7F00 - 000040D8, CacheErr_Dcache : 0x00000000 - 00001FA0
    TagLo_Icache : 0x00000000 - 23642303, DataLo_Icache : 0xAFBF0018 - 0D81ADDB
    DataHi_Icache: 0x00000000 - 00000001
    TagLo_Dcache : 0x00000000 - 2277E583, TagHi_Dcache : 0x00000000 - 0912BD81
    DataLo_Dcache: 0x00000001 - 2368110C, DataHi_Dcache : 0x00000000 - 0000001C
    TEXT_START : 0x21003178
    DATA_START : 0x260888A0
    Cause 0000040C (Code 0x3): TLB (store) exception
    Writing crashinfo to flash:crashinfo_20101028-220211-UTC
    22:02:11 UTC Thu Oct 28 2010: TLB (store) exception, CPU signal 10, PC = 0x22768478

    --------------------------------------------------------------------
    Possible software fault. Upon reccurence, please collect
    crashinfo, "show tech" and contact Cisco Technical Support.
    --------------------------------------------------------------------

    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z
    $0 : 00000000 00000000, AT : 00000000 29130000, v0 : 00000000 00000001, v1 : 00000000 0D8B8540
    a0 : 00000000 00000000, a1 : 00000000 0D8B8584, a2 : 00000000 2A2F8ABC, a3 : 00000000 00000004
    t0 : 00000000 00000020, t1 : 00000000 500099E1, t2 : 00000000 500081E0, t3 : FFFFFFFF FFFFFFF2
    t4 : 00000000 0000000E, t5 : 00000000 00000000, t6 : 00000000 0D95F890, t7 : 00000000 000001FF
    s0 : 00000000 00000000, s1 : 00000000 2A2FDB40, s2 : FFFFFFFF FFFFFFEC, s3 : 00000000 3080C980
    s4 : 00000000 0D95F89E, s5 : 00000000 2A300EE0, s6 : 00000000 00000000, s7 : 00000000 0000000E
    t8 : 00000000 000007FC, t9 : 00000000 2A300200, k0 : 00000000 00000000, k1 : 00000000 00000000
    gp : 00000000 29133C00, sp : 00000000 3022FBB8, s8 : 00000000 00000054, ra : 00000000 22768424
    EPC : 22768478, ErrorEPC : 80412AB4, SREG : 500099E3
    MDLO : 87126668, MDHI : D990ADBB, BadVaddr : 00000014
    CacheErr_Icache : 0x007F7F00 - 000040D8, CacheErr_Dcache : 0x00000000 - 00001FA0
    TagLo_Icache : 0x00000000 - 23642303, DataLo_Icache : 0xAFBF0018 - 0D81ADDB
    DataHi_Icache: 0x00000000 - 00000001
    TagLo_Dcache : 0x00000000 - 2277E583, TagHi_Dcache : 0x00000000 - 0912BD81
    DataLo_Dcache: 0x00000001 - 2368110C, DataHi_Dcache : 0x00000000 - 0000001C
    TEXT_START : 0x21003178
    DATA_START : 0x260888A0
    Cause 0000040C (Code 0x3): TLB (store) exception
    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z

    === Flushing messages (22:02:12 UTC Thu Oct 28 2010) ===
    Buffered messages:
    *Oct 28 20:52:40.075: %LINK-3-UPDOWN: Interface SM1/0, changed state to up
    *Oct 28 20:52:42.195: %LINK-3-UPDOWN: Interface GigabitEthernet0/0, changed state to up
    *Oct 28 20:52:42.195: %LINK-3-UPDOWN: Interface GigabitEthernet0/1, changed state to down
    *Oct 28 20:52:42.195: %LINK-3-UPDOWN: Interface GigabitEthernet0/2, changed state to down
    *Oct 28 20:52:44.631: %LINK-3-UPDOWN: Interface SM1/1, changed state to up
    *Oct 28 20:53:01.655: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/0, changed state to up
    *Oct 28 20:53:01.923: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/1, changed state to up
    *Oct 28 20:53:02.075: %LINK-3-UPDOWN: Interface Foreign Exchange Station 0/1/0, changed state to up
    *Oct 28 20:53:02.075: %LINK-3-UPDOWN: Interface Foreign Exchange Station 0/1/1, changed state to up
    *Oct 28 20:53:43.739: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/0, changed state to operational status down due to cable removal
    *Oct 28 20:53:44.739: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/1, changed state to operational status down due to cable removal
    Queued messages:
    No warm reboot Storage
    *** System received a Bus Error exception ***
    signal= 0xa, code= 0x40c, context= 0x29726b74
    PC = 0x22768478, SP = 0x3022fbb8, RA = 0x22768424
    Cause Reg = 0x0000040c, Status Reg = 0x500099e3
    System Bootstrap, Version 15.0(1r)M6, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 2010 by cisco Systems, Inc.
    Total memory size = 512 MB - On-board = 512 MB, DIMM0 = 0 MB
    CISCO2911/K9 platform with 524288 Kbytes of main memory
    Main memory is configured to 72/-1(On-board/DIMM0) bit mode with ECC enabled

    Readonly ROMMON initialized
    program load complete, entry point: 0x80803000, size: 0x1b340

    IOS Image Load Test
    ___________________
    Digitally Signed Development Software
    program load complete, entry point: 0x81000000, size: 0x40b6b74
    Self decompressing the image : #############################################################################################################

    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2691036>
    or simply reply to this email.

    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2691978>
    or simply reply to this email.

    Subject: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-
    Replied by: Brett Tiller on 20-11-2010 01:34:35 AM
    Hi Ken,



    We will publish this file for your specific access shortly.  You¿ll be receiving an e-mail from our server with access codes/location.



    Thanks,



    Brett

    Custom Application Engineer

    http://developer.cisco.com/web/axp/home



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Friday, October 29, 2010 12:36 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    Thank you.

    Have you had a chance to post new IOS (I have a 2911 ISR)?
    Just checked site and did not see it.

    Ken Romo


    Ken,

    I am trying to get some help from the IOS team since this a router crash. So I will setup the webex session to debug for some time Monday so we can collect all the information and try out any suggestion from them.



    For Now We will post a newer IOS image to the beta Site and can you give that a try to see if that will solve the issue.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Friday, October 29, 2010 8:24 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    I will work around your schedule, anytime you are available, I will make myself available.
    email:
    kromo@opentext.com

    Thanks in advance,

    Ken Romo

    +++++++++++++++++++++++++++++++++

    Ken,

    Would a webex session tomorrow morning (any time between 10:00 and 1:00) work for you? Let me know the time that would work for you and also your email address so I can send you a webex invite.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Thursday, October 28, 2010 3:12 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Radhika Miriyala in Service Ready Engine Virtualizatio



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    No worries, we are trying to work this out together and I appreciate the help.
    s/m 1/1 is set as trunk but I went ahead and reconfigured to truank again and reloaded OS and get the same crash when I ping to the MGF interface from the SRE (I attached the errors at the bottom of this message).

    Ken,

    Sorry I just realized the mistake. I meant to say make the interface sm 1/1 as trunk.

    Sorry about the confusion.



    Please try it out.



    Thanks,

    Radhika



    boxer#
    %ALIGN-1-FATAL: Illegal access to a low address 22:02:10 UTC Thu Oct 28 2010
    addr=0x14, pc=0x22765BD8z , ra=0x22765B84z , sp=0x3022FBB8
    %ALIGN-1-FATAL: Illegal access to a low address 22:02:11 UTC Thu Oct 28 2010
    addr=0x14, pc=0x22765BD8z , ra=0x22765B84z , sp=0x3022FBB8

    22:02:11 UTC Thu Oct 28 2010: TLB (store) exception, CPU signal 10, PC = 0x22768478

    --------------------------------------------------------------------
    Possible software fault. Upon reccurence, please collect
    crashinfo, "show tech" and contact Cisco Technical Support.
    --------------------------------------------------------------------

    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z
    $0 : 00000000 00000000, AT : 00000000 29130000, v0 : 00000000 00000001, v1 : 00000000 0D8B8540
    a0 : 00000000 00000000, a1 : 00000000 0D8B8584, a2 : 00000000 2A2F8ABC, a3 : 00000000 00000004
    t0 : 00000000 00000020, t1 : 00000000 500099E1, t2 : 00000000 500081E0, t3 : FFFFFFFF FFFFFFF2
    t4 : 00000000 0000000E, t5 : 00000000 00000000, t6 : 00000000 0D95F890, t7 : 00000000 000001FF
    s0 : 00000000 00000000, s1 : 00000000 2A2FDB40, s2 : FFFFFFFF FFFFFFEC, s3 : 00000000 3080C980
    s4 : 00000000 0D95F89E, s5 : 00000000 2A300EE0, s6 : 00000000 00000000, s7 : 00000000 0000000E
    t8 : 00000000 000007FC, t9 : 00000000 2A300200, k0 : 00000000 00000000, k1 : 00000000 00000000
    gp : 00000000 29133C00, sp : 00000000 3022FBB8, s8 : 00000000 00000054, ra : 00000000 22768424
    EPC : 22768478, ErrorEPC : 80412AB4, SREG : 500099E3
    MDLO : 87126668, MDHI : D990ADBB, BadVaddr : 00000014
    CacheErr_Icache : 0x007F7F00 - 000040D8, CacheErr_Dcache : 0x00000000 - 00001FA0
    TagLo_Icache : 0x00000000 - 23642303, DataLo_Icache : 0xAFBF0018 - 0D81ADDB
    DataHi_Icache: 0x00000000 - 00000001
    TagLo_Dcache : 0x00000000 - 2277E583, TagHi_Dcache : 0x00000000 - 0912BD81
    DataLo_Dcache: 0x00000001 - 2368110C, DataHi_Dcache : 0x00000000 - 0000001C
    TEXT_START : 0x21003178
    DATA_START : 0x260888A0
    Cause 0000040C (Code 0x3): TLB (store) exception

    22:02:11 UTC Thu Oct 28 2010: TLB (store) exception, CPU signal 10, PC = 0x22768478

    --------------------------------------------------------------------
    Possible software fault. Upon reccurence, please collect
    crashinfo, "show tech" and contact Cisco Technical Support.
    --------------------------------------------------------------------

    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z
    $0 : 00000000 00000000, AT : 00000000 29130000, v0 : 00000000 00000001, v1 : 00000000 0D8B8540
    a0 : 00000000 00000000, a1 : 00000000 0D8B8584, a2 : 00000000 2A2F8ABC, a3 : 00000000 00000004
    t0 : 00000000 00000020, t1 : 00000000 500099E1, t2 : 00000000 500081E0, t3 : FFFFFFFF FFFFFFF2
    t4 : 00000000 0000000E, t5 : 00000000 00000000, t6 : 00000000 0D95F890, t7 : 00000000 000001FF
    s0 : 00000000 00000000, s1 : 00000000 2A2FDB40, s2 : FFFFFFFF FFFFFFEC, s3 : 00000000 3080C980
    s4 : 00000000 0D95F89E, s5 : 00000000 2A300EE0, s6 : 00000000 00000000, s7 : 00000000 0000000E
    t8 : 00000000 000007FC, t9 : 00000000 2A300200, k0 : 00000000 00000000, k1 : 00000000 00000000
    gp : 00000000 29133C00, sp : 00000000 3022FBB8, s8 : 00000000 00000054, ra : 00000000 22768424
    EPC : 22768478, ErrorEPC : 80412AB4, SREG : 500099E3
    MDLO : 87126668, MDHI : D990ADBB, BadVaddr : 00000014
    CacheErr_Icache : 0x007F7F00 - 000040D8, CacheErr_Dcache : 0x00000000 - 00001FA0
    TagLo_Icache : 0x00000000 - 23642303, DataLo_Icache : 0xAFBF0018 - 0D81ADDB
    DataHi_Icache: 0x00000000 - 00000001
    TagLo_Dcache : 0x00000000 - 2277E583, TagHi_Dcache : 0x00000000 - 0912BD81
    DataLo_Dcache: 0x00000001 - 2368110C, DataHi_Dcache : 0x00000000 - 0000001C
    TEXT_START : 0x21003178
    DATA_START : 0x260888A0
    Cause 0000040C (Code 0x3): TLB (store) exception
    Writing crashinfo to flash:crashinfo_20101028-220211-UTC
    22:02:11 UTC Thu Oct 28 2010: TLB (store) exception, CPU signal 10, PC = 0x22768478

    --------------------------------------------------------------------
    Possible software fault. Upon reccurence, please collect
    crashinfo, "show tech" and contact Cisco Technical Support.
    --------------------------------------------------------------------

    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z
    $0 : 00000000 00000000, AT : 00000000 29130000, v0 : 00000000 00000001, v1 : 00000000 0D8B8540
    a0 : 00000000 00000000, a1 : 00000000 0D8B8584, a2 : 00000000 2A2F8ABC, a3 : 00000000 00000004
    t0 : 00000000 00000020, t1 : 00000000 500099E1, t2 : 00000000 500081E0, t3 : FFFFFFFF FFFFFFF2
    t4 : 00000000 0000000E, t5 : 00000000 00000000, t6 : 00000000 0D95F890, t7 : 00000000 000001FF
    s0 : 00000000 00000000, s1 : 00000000 2A2FDB40, s2 : FFFFFFFF FFFFFFEC, s3 : 00000000 3080C980
    s4 : 00000000 0D95F89E, s5 : 00000000 2A300EE0, s6 : 00000000 00000000, s7 : 00000000 0000000E
    t8 : 00000000 000007FC, t9 : 00000000 2A300200, k0 : 00000000 00000000, k1 : 00000000 00000000
    gp : 00000000 29133C00, sp : 00000000 3022FBB8, s8 : 00000000 00000054, ra : 00000000 22768424
    EPC : 22768478, ErrorEPC : 80412AB4, SREG : 500099E3
    MDLO : 87126668, MDHI : D990ADBB, BadVaddr : 00000014
    CacheErr_Icache : 0x007F7F00 - 000040D8, CacheErr_Dcache : 0x00000000 - 00001FA0
    TagLo_Icache : 0x00000000 - 23642303, DataLo_Icache : 0xAFBF0018 - 0D81ADDB
    DataHi_Icache: 0x00000000 - 00000001
    TagLo_Dcache : 0x00000000 - 2277E583, TagHi_Dcache : 0x00000000 - 0912BD81
    DataLo_Dcache: 0x00000001 - 2368110C, DataHi_Dcache : 0x00000000 - 0000001C
    TEXT_START : 0x21003178
    DATA_START : 0x260888A0
    Cause 0000040C (Code 0x3): TLB (store) exception
    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z

    === Flushing messages (22:02:12 UTC Thu Oct 28 2010) ===
    Buffered messages:
    *Oct 28 20:52:40.075: %LINK-3-UPDOWN: Interface SM1/0, changed state to up
    *Oct 28 20:52:42.195: %LINK-3-UPDOWN: Interface GigabitEthernet0/0, changed state to up
    *Oct 28 20:52:42.195: %LINK-3-UPDOWN: Interface GigabitEthernet0/1, changed state to down
    *Oct 28 20:52:42.195: %LINK-3-UPDOWN: Interface GigabitEthernet0/2, changed state to down
    *Oct 28 20:52:44.631: %LINK-3-UPDOWN: Interface SM1/1, changed state to up
    *Oct 28 20:53:01.655: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/0, changed state to up
    *Oct 28 20:53:01.923: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/1, changed state to up
    *Oct 28 20:53:02.075: %LINK-3-UPDOWN: Interface Foreign Exchange Station 0/1/0, changed state to up
    *Oct 28 20:53:02.075: %LINK-3-UPDOWN: Interface Foreign Exchange Station 0/1/1, changed state to up
    *Oct 28 20:53:43.739: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/0, changed state to operational status down due to cable removal
    *Oct 28 20:53:44.739: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/1, changed state to operational status down due to cable removal
    Queued messages:
    No warm reboot Storage
    *** System received a Bus Error exception ***
    signal= 0xa, code= 0x40c, context= 0x29726b74
    PC = 0x22768478, SP = 0x3022fbb8, RA = 0x22768424
    Cause Reg = 0x0000040c, Status Reg = 0x500099e3
    System Bootstrap, Version 15.0(1r)M6, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 2010 by cisco Systems, Inc.
    Total memory size = 512 MB - On-board = 512 MB, DIMM0 = 0 MB
    CISCO2911/K9 platform with 524288 Kbytes of main memory
    Main memory is configured to 72/-1(On-board/DIMM0) bit mode with ECC enabled

    Readonly ROMMON initialized
    program load complete, entry point: 0x80803000, size: 0x1b340

    IOS Image Load Test
    ___________________
    Digitally Signed Development Software
    program load complete, entry point: 0x81000000, size: 0x40b6b74
    Self decompressing the image : #############################################################################################################

    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2691036>
    or simply reply to this email.
    -- --
    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2691978>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2694333>
    or simply reply to this email.

    Subject: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-
    Replied by: Ken Romo on 20-11-2010 01:34:35 AM
     
    Radhika,
     
    I tried the new OS and still getting same IOS crash.
    As mentioned I will work around your schedule so let me if you were able to get someone from the IOS team to help troubleshoot today.
     
    Thanks in advance,
     
    Ken Romo
     
    Ken,

    I am trying to get some help from the IOS team since this a router crash. So I will setup the webex session to debug for some time Monday so we can collect all the information and try out any suggestion from them.



    For Now We will post a newer IOS image to the beta Site and can you give that a try to see if that will solve the issue.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Friday, October 29, 2010 8:24 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    I will work around your schedule, anytime you are available, I will make myself available.
    email:
    kromo@opentext.com

    Thanks in advance,

    Ken Romo

    +++++++++++++++++++++++++++++++++

    Ken,

    Would a webex session tomorrow morning (any time between 10:00 and 1:00) work for you? Let me know the time that would work for you and also your email address so I can send you a webex invite.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Thursday, October 28, 2010 3:12 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Radhika Miriyala in Service Ready Engine Virtualizatio



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    No worries, we are trying to work this out together and I appreciate the help.
    s/m 1/1 is set as trunk but I went ahead and reconfigured to truank again and reloaded OS and get the same crash when I ping to the MGF interface from the SRE (I attached the errors at the bottom of this message).

    Ken,

    Sorry I just realized the mistake. I meant to say make the interface sm 1/1 as trunk.

    Sorry about the confusion.



    Please try it out.



    Thanks,

    Radhika



    boxer#
    %ALIGN-1-FATAL: Illegal access to a low address 22:02:10 UTC Thu Oct 28 2010
    addr=0x14, pc=0x22765BD8z , ra=0x22765B84z , sp=0x3022FBB8
    %ALIGN-1-FATAL: Illegal access to a low address 22:02:11 UTC Thu Oct 28 2010
    addr=0x14, pc=0x22765BD8z , ra=0x22765B84z , sp=0x3022FBB8

    22:02:11 UTC Thu Oct 28 2010: TLB (store) exception, CPU signal 10, PC = 0x22768478

    --------------------------------------------------------------------
    Possible software fault. Upon reccurence, please collect
    crashinfo, "show tech" and contact Cisco Technical Support.
    --------------------------------------------------------------------

    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z
    $0 : 00000000 00000000, AT : 00000000 29130000, v0 : 00000000 00000001, v1 : 00000000 0D8B8540
    a0 : 00000000 00000000, a1 : 00000000 0D8B8584, a2 : 00000000 2A2F8ABC, a3 : 00000000 00000004
    t0 : 00000000 00000020, t1 : 00000000 500099E1, t2 : 00000000 500081E0, t3 : FFFFFFFF FFFFFFF2
    t4 : 00000000 0000000E, t5 : 00000000 00000000, t6 : 00000000 0D95F890, t7 : 00000000 000001FF
    s0 : 00000000 00000000, s1 : 00000000 2A2FDB40, s2 : FFFFFFFF FFFFFFEC, s3 : 00000000 3080C980
    s4 : 00000000 0D95F89E, s5 : 00000000 2A300EE0, s6 : 00000000 00000000, s7 : 00000000 0000000E
    t8 : 00000000 000007FC, t9 : 00000000 2A300200, k0 : 00000000 00000000, k1 : 00000000 00000000
    gp : 00000000 29133C00, sp : 00000000 3022FBB8, s8 : 00000000 00000054, ra : 00000000 22768424
    EPC : 22768478, ErrorEPC : 80412AB4, SREG : 500099E3
    MDLO : 87126668, MDHI : D990ADBB, BadVaddr : 00000014
    CacheErr_Icache : 0x007F7F00 - 000040D8, CacheErr_Dcache : 0x00000000 - 00001FA0
    TagLo_Icache : 0x00000000 - 23642303, DataLo_Icache : 0xAFBF0018 - 0D81ADDB
    DataHi_Icache: 0x00000000 - 00000001
    TagLo_Dcache : 0x00000000 - 2277E583, TagHi_Dcache : 0x00000000 - 0912BD81
    DataLo_Dcache: 0x00000001 - 2368110C, DataHi_Dcache : 0x00000000 - 0000001C
    TEXT_START : 0x21003178
    DATA_START : 0x260888A0
    Cause 0000040C (Code 0x3): TLB (store) exception

    22:02:11 UTC Thu Oct 28 2010: TLB (store) exception, CPU signal 10, PC = 0x22768478

    --------------------------------------------------------------------
    Possible software fault. Upon reccurence, please collect
    crashinfo, "show tech" and contact Cisco Technical Support.
    --------------------------------------------------------------------

    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z
    $0 : 00000000 00000000, AT : 00000000 29130000, v0 : 00000000 00000001, v1 : 00000000 0D8B8540
    a0 : 00000000 00000000, a1 : 00000000 0D8B8584, a2 : 00000000 2A2F8ABC, a3 : 00000000 00000004
    t0 : 00000000 00000020, t1 : 00000000 500099E1, t2 : 00000000 500081E0, t3 : FFFFFFFF FFFFFFF2
    t4 : 00000000 0000000E, t5 : 00000000 00000000, t6 : 00000000 0D95F890, t7 : 00000000 000001FF
    s0 : 00000000 00000000, s1 : 00000000 2A2FDB40, s2 : FFFFFFFF FFFFFFEC, s3 : 00000000 3080C980
    s4 : 00000000 0D95F89E, s5 : 00000000 2A300EE0, s6 : 00000000 00000000, s7 : 00000000 0000000E
    t8 : 00000000 000007FC, t9 : 00000000 2A300200, k0 : 00000000 00000000, k1 : 00000000 00000000
    gp : 00000000 29133C00, sp : 00000000 3022FBB8, s8 : 00000000 00000054, ra : 00000000 22768424
    EPC : 22768478, ErrorEPC : 80412AB4, SREG : 500099E3
    MDLO : 87126668, MDHI : D990ADBB, BadVaddr : 00000014
    CacheErr_Icache : 0x007F7F00 - 000040D8, CacheErr_Dcache : 0x00000000 - 00001FA0
    TagLo_Icache : 0x00000000 - 23642303, DataLo_Icache : 0xAFBF0018 - 0D81ADDB
    DataHi_Icache: 0x00000000 - 00000001
    TagLo_Dcache : 0x00000000 - 2277E583, TagHi_Dcache : 0x00000000 - 0912BD81
    DataLo_Dcache: 0x00000001 - 2368110C, DataHi_Dcache : 0x00000000 - 0000001C
    TEXT_START : 0x21003178
    DATA_START : 0x260888A0
    Cause 0000040C (Code 0x3): TLB (store) exception
    Writing crashinfo to flash:crashinfo_20101028-220211-UTC
    22:02:11 UTC Thu Oct 28 2010: TLB (store) exception, CPU signal 10, PC = 0x22768478

    --------------------------------------------------------------------
    Possible software fault. Upon reccurence, please collect
    crashinfo, "show tech" and contact Cisco Technical Support.
    --------------------------------------------------------------------

    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z
    $0 : 00000000 00000000, AT : 00000000 29130000, v0 : 00000000 00000001, v1 : 00000000 0D8B8540
    a0 : 00000000 00000000, a1 : 00000000 0D8B8584, a2 : 00000000 2A2F8ABC, a3 : 00000000 00000004
    t0 : 00000000 00000020, t1 : 00000000 500099E1, t2 : 00000000 500081E0, t3 : FFFFFFFF FFFFFFF2
    t4 : 00000000 0000000E, t5 : 00000000 00000000, t6 : 00000000 0D95F890, t7 : 00000000 000001FF
    s0 : 00000000 00000000, s1 : 00000000 2A2FDB40, s2 : FFFFFFFF FFFFFFEC, s3 : 00000000 3080C980
    s4 : 00000000 0D95F89E, s5 : 00000000 2A300EE0, s6 : 00000000 00000000, s7 : 00000000 0000000E
    t8 : 00000000 000007FC, t9 : 00000000 2A300200, k0 : 00000000 00000000, k1 : 00000000 00000000
    gp : 00000000 29133C00, sp : 00000000 3022FBB8, s8 : 00000000 00000054, ra : 00000000 22768424
    EPC : 22768478, ErrorEPC : 80412AB4, SREG : 500099E3
    MDLO : 87126668, MDHI : D990ADBB, BadVaddr : 00000014
    CacheErr_Icache : 0x007F7F00 - 000040D8, CacheErr_Dcache : 0x00000000 - 00001FA0
    TagLo_Icache : 0x00000000 - 23642303, DataLo_Icache : 0xAFBF0018 - 0D81ADDB
    DataHi_Icache: 0x00000000 - 00000001
    TagLo_Dcache : 0x00000000 - 2277E583, TagHi_Dcache : 0x00000000 - 0912BD81
    DataLo_Dcache: 0x00000001 - 2368110C, DataHi_Dcache : 0x00000000 - 0000001C
    TEXT_START : 0x21003178
    DATA_START : 0x260888A0
    Cause 0000040C (Code 0x3): TLB (store) exception
    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z

    === Flushing messages (22:02:12 UTC Thu Oct 28 2010) ===
    Buffered messages:
    *Oct 28 20:52:40.075: %LINK-3-UPDOWN: Interface SM1/0, changed state to up
    *Oct 28 20:52:42.195: %LINK-3-UPDOWN: Interface GigabitEthernet0/0, changed state to up
    *Oct 28 20:52:42.195: %LINK-3-UPDOWN: Interface GigabitEthernet0/1, changed state to down
    *Oct 28 20:52:42.195: %LINK-3-UPDOWN: Interface GigabitEthernet0/2, changed state to down
    *Oct 28 20:52:44.631: %LINK-3-UPDOWN: Interface SM1/1, changed state to up
    *Oct 28 20:53:01.655: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/0, changed state to up
    *Oct 28 20:53:01.923: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/1, changed state to up
    *Oct 28 20:53:02.075: %LINK-3-UPDOWN: Interface Foreign Exchange Station 0/1/0, changed state to up
    *Oct 28 20:53:02.075: %LINK-3-UPDOWN: Interface Foreign Exchange Station 0/1/1, changed state to up
    *Oct 28 20:53:43.739: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/0, changed state to operational status down due to cable removal
    *Oct 28 20:53:44.739: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/1, changed state to operational status down due to cable removal
    Queued messages:
    No warm reboot Storage
    *** System received a Bus Error exception ***
    signal= 0xa, code= 0x40c, context= 0x29726b74
    PC = 0x22768478, SP = 0x3022fbb8, RA = 0x22768424
    Cause Reg = 0x0000040c, Status Reg = 0x500099e3
    System Bootstrap, Version 15.0(1r)M6, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 2010 by cisco Systems, Inc.
    Total memory size = 512 MB - On-board = 512 MB, DIMM0 = 0 MB
    CISCO2911/K9 platform with 524288 Kbytes of main memory
    Main memory is configured to 72/-1(On-board/DIMM0) bit mode with ECC enabled

    Readonly ROMMON initialized
    program load complete, entry point: 0x80803000, size: 0x1b340

    IOS Image Load Test
    ___________________
    Digitally Signed Development Software
    program load complete, entry point: 0x81000000, size: 0x40b6b74
    Self decompressing the image : #############################################################################################################

    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2691036>
    or simply reply to this email.
    -- --
    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2691978>
    or simply reply to this email.


    Subject: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-
    Replied by: Radhika Miriyala on 20-11-2010 01:34:35 AM
    Ken, Thanks for trying out the image for us. We are trying to reproduce this on our end but have had no luck so far. Can you please send us the output of show running-config from your router.



    Also we have one more image that we would like you to try it out before the debusg session would that be ok?



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Monday, November 01, 2010 10:22 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------

    Radhika,

    I tried the new OS and still getting same IOS crash.
    As mentioned I will work around your schedule so let me if you were able to get someone from the IOS team to help troubleshoot today.

    Thanks in advance,

    Ken Romo


    Ken,

    I am trying to get some help from the IOS team since this a router crash. So I will setup the webex session to debug for some time Monday so we can collect all the information and try out any suggestion from them.



    For Now We will post a newer IOS image to the beta Site and can you give that a try to see if that will solve the issue.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Friday, October 29, 2010 8:24 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    I will work around your schedule, anytime you are available, I will make myself available.
    email:
    kromo@opentext.com

    Thanks in advance,

    Ken Romo

    +++++++++++++++++++++++++++++++++

    Ken,

    Would a webex session tomorrow morning (any time between 10:00 and 1:00) work for you? Let me know the time that would work for you and also your email address so I can send you a webex invite.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Thursday, October 28, 2010 3:12 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Radhika Miriyala in Service Ready Engine Virtualizatio



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    No worries, we are trying to work this out together and I appreciate the help.
    s/m 1/1 is set as trunk but I went ahead and reconfigured to truank again and reloaded OS and get the same crash when I ping to the MGF interface from the SRE (I attached the errors at the bottom of this message).

    Ken,

    Sorry I just realized the mistake. I meant to say make the interface sm 1/1 as trunk.

    Sorry about the confusion.



    Please try it out.



    Thanks,

    Radhika



    boxer#
    %ALIGN-1-FATAL: Illegal access to a low address 22:02:10 UTC Thu Oct 28 2010
    addr=0x14, pc=0x22765BD8z , ra=0x22765B84z , sp=0x3022FBB8
    %ALIGN-1-FATAL: Illegal access to a low address 22:02:11 UTC Thu Oct 28 2010
    addr=0x14, pc=0x22765BD8z , ra=0x22765B84z , sp=0x3022FBB8

    22:02:11 UTC Thu Oct 28 2010: TLB (store) exception, CPU signal 10, PC = 0x22768478

    --------------------------------------------------------------------
    Possible software fault. Upon reccurence, please collect
    crashinfo, "show tech" and contact Cisco Technical Support.
    --------------------------------------------------------------------

    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z
    $0 : 00000000 00000000, AT : 00000000 29130000, v0 : 00000000 00000001, v1 : 00000000 0D8B8540
    a0 : 00000000 00000000, a1 : 00000000 0D8B8584, a2 : 00000000 2A2F8ABC, a3 : 00000000 00000004
    t0 : 00000000 00000020, t1 : 00000000 500099E1, t2 : 00000000 500081E0, t3 : FFFFFFFF FFFFFFF2
    t4 : 00000000 0000000E, t5 : 00000000 00000000, t6 : 00000000 0D95F890, t7 : 00000000 000001FF
    s0 : 00000000 00000000, s1 : 00000000 2A2FDB40, s2 : FFFFFFFF FFFFFFEC, s3 : 00000000 3080C980
    s4 : 00000000 0D95F89E, s5 : 00000000 2A300EE0, s6 : 00000000 00000000, s7 : 00000000 0000000E
    t8 : 00000000 000007FC, t9 : 00000000 2A300200, k0 : 00000000 00000000, k1 : 00000000 00000000
    gp : 00000000 29133C00, sp : 00000000 3022FBB8, s8 : 00000000 00000054, ra : 00000000 22768424
    EPC : 22768478, ErrorEPC : 80412AB4, SREG : 500099E3
    MDLO : 87126668, MDHI : D990ADBB, BadVaddr : 00000014
    CacheErr_Icache : 0x007F7F00 - 000040D8, CacheErr_Dcache : 0x00000000 - 00001FA0
    TagLo_Icache : 0x00000000 - 23642303, DataLo_Icache : 0xAFBF0018 - 0D81ADDB
    DataHi_Icache: 0x00000000 - 00000001
    TagLo_Dcache : 0x00000000 - 2277E583, TagHi_Dcache : 0x00000000 - 0912BD81
    DataLo_Dcache: 0x00000001 - 2368110C, DataHi_Dcache : 0x00000000 - 0000001C
    TEXT_START : 0x21003178
    DATA_START : 0x260888A0
    Cause 0000040C (Code 0x3): TLB (store) exception

    22:02:11 UTC Thu Oct 28 2010: TLB (store) exception, CPU signal 10, PC = 0x22768478

    --------------------------------------------------------------------
    Possible software fault. Upon reccurence, please collect
    crashinfo, "show tech" and contact Cisco Technical Support.
    --------------------------------------------------------------------

    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z
    $0 : 00000000 00000000, AT : 00000000 29130000, v0 : 00000000 00000001, v1 : 00000000 0D8B8540
    a0 : 00000000 00000000, a1 : 00000000 0D8B8584, a2 : 00000000 2A2F8ABC, a3 : 00000000 00000004
    t0 : 00000000 00000020, t1 : 00000000 500099E1, t2 : 00000000 500081E0, t3 : FFFFFFFF FFFFFFF2
    t4 : 00000000 0000000E, t5 : 00000000 00000000, t6 : 00000000 0D95F890, t7 : 00000000 000001FF
    s0 : 00000000 00000000, s1 : 00000000 2A2FDB40, s2 : FFFFFFFF FFFFFFEC, s3 : 00000000 3080C980
    s4 : 00000000 0D95F89E, s5 : 00000000 2A300EE0, s6 : 00000000 00000000, s7 : 00000000 0000000E
    t8 : 00000000 000007FC, t9 : 00000000 2A300200, k0 : 00000000 00000000, k1 : 00000000 00000000
    gp : 00000000 29133C00, sp : 00000000 3022FBB8, s8 : 00000000 00000054, ra : 00000000 22768424
    EPC : 22768478, ErrorEPC : 80412AB4, SREG : 500099E3
    MDLO : 87126668, MDHI : D990ADBB, BadVaddr : 00000014
    CacheErr_Icache : 0x007F7F00 - 000040D8, CacheErr_Dcache : 0x00000000 - 00001FA0
    TagLo_Icache : 0x00000000 - 23642303, DataLo_Icache : 0xAFBF0018 - 0D81ADDB
    DataHi_Icache: 0x00000000 - 00000001
    TagLo_Dcache : 0x00000000 - 2277E583, TagHi_Dcache : 0x00000000 - 0912BD81
    DataLo_Dcache: 0x00000001 - 2368110C, DataHi_Dcache : 0x00000000 - 0000001C
    TEXT_START : 0x21003178
    DATA_START : 0x260888A0
    Cause 0000040C (Code 0x3): TLB (store) exception
    Writing crashinfo to flash:crashinfo_20101028-220211-UTC
    22:02:11 UTC Thu Oct 28 2010: TLB (store) exception, CPU signal 10, PC = 0x22768478

    --------------------------------------------------------------------
    Possible software fault. Upon reccurence, please collect
    crashinfo, "show tech" and contact Cisco Technical Support.
    --------------------------------------------------------------------

    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z
    $0 : 00000000 00000000, AT : 00000000 29130000, v0 : 00000000 00000001, v1 : 00000000 0D8B8540
    a0 : 00000000 00000000, a1 : 00000000 0D8B8584, a2 : 00000000 2A2F8ABC, a3 : 00000000 00000004
    t0 : 00000000 00000020, t1 : 00000000 500099E1, t2 : 00000000 500081E0, t3 : FFFFFFFF FFFFFFF2
    t4 : 00000000 0000000E, t5 : 00000000 00000000, t6 : 00000000 0D95F890, t7 : 00000000 000001FF
    s0 : 00000000 00000000, s1 : 00000000 2A2FDB40, s2 : FFFFFFFF FFFFFFEC, s3 : 00000000 3080C980
    s4 : 00000000 0D95F89E, s5 : 00000000 2A300EE0, s6 : 00000000 00000000, s7 : 00000000 0000000E
    t8 : 00000000 000007FC, t9 : 00000000 2A300200, k0 : 00000000 00000000, k1 : 00000000 00000000
    gp : 00000000 29133C00, sp : 00000000 3022FBB8, s8 : 00000000 00000054, ra : 00000000 22768424
    EPC : 22768478, ErrorEPC : 80412AB4, SREG : 500099E3
    MDLO : 87126668, MDHI : D990ADBB, BadVaddr : 00000014
    CacheErr_Icache : 0x007F7F00 - 000040D8, CacheErr_Dcache : 0x00000000 - 00001FA0
    TagLo_Icache : 0x00000000 - 23642303, DataLo_Icache : 0xAFBF0018 - 0D81ADDB
    DataHi_Icache: 0x00000000 - 00000001
    TagLo_Dcache : 0x00000000 - 2277E583, TagHi_Dcache : 0x00000000 - 0912BD81
    DataLo_Dcache: 0x00000001 - 2368110C, DataHi_Dcache : 0x00000000 - 0000001C
    TEXT_START : 0x21003178
    DATA_START : 0x260888A0
    Cause 0000040C (Code 0x3): TLB (store) exception
    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z

    === Flushing messages (22:02:12 UTC Thu Oct 28 2010) ===
    Buffered messages:
    *Oct 28 20:52:40.075: %LINK-3-UPDOWN: Interface SM1/0, changed state to up
    *Oct 28 20:52:42.195: %LINK-3-UPDOWN: Interface GigabitEthernet0/0, changed state to up
    *Oct 28 20:52:42.195: %LINK-3-UPDOWN: Interface GigabitEthernet0/1, changed state to down
    *Oct 28 20:52:42.195: %LINK-3-UPDOWN: Interface GigabitEthernet0/2, changed state to down
    *Oct 28 20:52:44.631: %LINK-3-UPDOWN: Interface SM1/1, changed state to up
    *Oct 28 20:53:01.655: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/0, changed state to up
    *Oct 28 20:53:01.923: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/1, changed state to up
    *Oct 28 20:53:02.075: %LINK-3-UPDOWN: Interface Foreign Exchange Station 0/1/0, changed state to up
    *Oct 28 20:53:02.075: %LINK-3-UPDOWN: Interface Foreign Exchange Station 0/1/1, changed state to up
    *Oct 28 20:53:43.739: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/0, changed state to operational status down due to cable removal
    *Oct 28 20:53:44.739: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/1, changed state to operational status down due to cable removal
    Queued messages:
    No warm reboot Storage
    *** System received a Bus Error exception ***
    signal= 0xa, code= 0x40c, context= 0x29726b74
    PC = 0x22768478, SP = 0x3022fbb8, RA = 0x22768424
    Cause Reg = 0x0000040c, Status Reg = 0x500099e3
    System Bootstrap, Version 15.0(1r)M6, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 2010 by cisco Systems, Inc.
    Total memory size = 512 MB - On-board = 512 MB, DIMM0 = 0 MB
    CISCO2911/K9 platform with 524288 Kbytes of main memory
    Main memory is configured to 72/-1(On-board/DIMM0) bit mode with ECC enabled

    Readonly ROMMON initialized
    program load complete, entry point: 0x80803000, size: 0x1b340

    IOS Image Load Test
    ___________________
    Digitally Signed Development Software
    program load complete, entry point: 0x81000000, size: 0x40b6b74
    Self decompressing the image : #############################################################################################################

    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2691036>
    or simply reply to this email.
    -- --
    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2691978>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2699015>
    or simply reply to this email.

    Subject: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-
    Replied by: Ken Romo on 20-11-2010 01:34:36 AM
    Radhika,
     
    I will try whatever you suggest, just let me know when you have posted the new IOS.
     
    Below is my config:
     
    boxer#sh run
    Building configuration...

    Current configuration : 5777 bytes
    !
    version 15.1
    service timestamps debug datetime msec
    service timestamps log datetime msec
    no service password-encryption
    !
    hostname boxer
    !
    boot-start-marker
    boot system flash0 c2900-universalk9-mz.SSA.151-2.19.T
    boot-end-marker
    !
    !
    logging buffered 51200 warnings
    !
    no aaa new-model
    !
    no ipv6 cef
    ip source-route
    ip cef
    !
    !
    !
    !
    !
    ip domain name yourdomain.com
    multilink bundle-name authenticated
    !
    !
    !
    !
    !
    crypto pki token default removal timeout 0
    !
    crypto pki trustpoint TP-self-signed-1999750280
     enrollment selfsigned
     subject-name cn=IOS-Self-Signed-Certificate-1999750280
     revocation-check none
     rsakeypair TP-self-signed-1999750280
    !
    !
    crypto pki certificate chain TP-self-signed-1999750280
     certificate self-signed 01
      3082024C 308201B5 A0030201 02020101 300D0609 2A864886 F70D0101 04050030
      31312F30 2D060355 04031326 494F532D 53656C66 2D536967 6E65642D 43657274
      69666963 6174652D 31393939 37353032 3830301E 170D3130 31303230 32323335
      32365A17 0D323030 31303130 30303030 305A3031 312F302D 06035504 03132649
      4F532D53 656C662D 5369676E 65642D43 65727469 66696361 74652D31 39393937
      35303238 3030819F 300D0609 2A864886 F70D0101 01050003 818D0030 81890281
      81009378 2E139D79 DCA59865 14AB3398 870362B7 40BB9C13 A5DC5315 6108DF92
      5E78CF06 A40D4DB5 B66D410E FAFE75AC 764997B1 5C551A47 CFA00109 520352EC
      33A69E24 B3C1175B 136FC62A 8BE4637E B834059B FC7CAA6E 957DA0BB 66D8DC49
      80F82890 981FFCFE 0DC7E6F9 53287989 3887C5F6 AF59D0BE B502E11E FD16F556
      DBB90203 010001A3 74307230 0F060355 1D130101 FF040530 030101FF 301F0603
      551D1104 18301682 14626F78 65722E79 6F757264 6F6D6169 6E2E636F 6D301F06
      03551D23 04183016 80143541 7934E424 4B9A60DB E6C908C3 C20BAA17 D058301D
      0603551D 0E041604 14354179 34E4244B 9A60DBE6 C908C3C2 0BAA17D0 58300D06
      092A8648 86F70D01 01040500 03818100 3D222AB5 177D452F 153DCA26 1D7ECB49
      58BCBF60 DA18DC04 94B82EA3 76884EBC D7131641 08687C04 6C6645DF 78B2D2F8
      409BCAD7 50AF5091 B99614FD C2424D89 407A9109 BCA20473 F4CE33D4 4B126483
      C240C0B9 7A628E53 E419FEC3 B8853671 03113F5E 47FA8120 9F9A7A9D 11498FE0
      82C96578 8FD9770A EBD27F73 DF2E1487
            quit
    voice-card 0
    !
    !
    !
    !
    !
    !
    !
    license udi pid CISCO2911/K9 sn FTX1422A077
    hw-module pvdm 0/0
    !
    hw-module sm 1
    !
    !
    !
    username jack privilege 15 secret 5 $1$c5QR$fYGTbhWRKsBZ1JpNyIQGG1
    username marco privilege 15 secret 5 $1$amqq$5pI0T7mUViDL5Y.NqX/yz.
    !
    redundancy
    !
    !
    !
    !
    !
    !
    interface GigabitEthernet0/0
     description To tusqa network
     ip address 172.17.17.130 255.255.248.0
     duplex auto
     speed auto
    !
    interface GigabitEthernet0/1
     no ip address
     shutdown
     duplex auto
     speed auto
    !
    interface GigabitEthernet0/2
     no ip address
     shutdown
     duplex auto
     speed auto
    !
    interface SM1/0
     ip unnumbered GigabitEthernet0/0
     service-module ip address 172.17.17.129 255.255.248.0
     !Application: SRE-V Running on SMV
     service-module ip default-gateway 172.17.17.130
     service-module mgf ip address 10.62.64.1 255.255.255.0
     service-module mgf ip default-gateway 10.62.64.2
    !
    interface SM1/1
     description Internal switch interface connected to Service Module
     switchport mode trunk
    !
    interface Vlan1
     ip address 10.62.64.2 255.255.255.0
    !
    ip forward-protocol nd
    !
    ip http server
    ip http access-class 23
    ip http authentication local
    ip http secure-server
    ip http timeout-policy idle 60 life 86400 requests 10000
    !
    ip route 172.17.17.129 255.255.255.255 SM1/0
    !
    !
    !
    !
    control-plane
    !
    !
    voice-port 0/0/0
    !
    voice-port 0/0/1
    !
    voice-port 0/1/0
    !
    voice-port 0/1/1
    !
    !
    !
    mgcp profile default
    !
    !
    !
    !
    !
    gatekeeper
     shutdown
    !
    !
    banner exec ^C
    % Password expiration warning.
    -----------------------------------------------------------------------
    Cisco Configuration Professional (Cisco CP) is installed on this device
    and it provides the default username "cisco" for  one-time use. If you have
    already used the username "cisco" to login to the router and your IOS image
    supports the "one-time" user option, then this username has already expired.
    You will not be able to login to the router with this username after you exit
    this session.
    It is strongly suggested that you create a new username with a privilege level
    of 15 using the following command.
    username <myuser> privilege 15 secret 0 <mypassword>
    Replace <myuser> and <mypassword> with the username and password you want to
    use.
    -----------------------------------------------------------------------
    ^C
    banner login ^C
    -----------------------------------------------------------------------
    Cisco Configuration Professional (Cisco CP) is installed on this device.
    This feature requires the one-time use of the username "cisco" with the
    password "cisco". These default credentials have a privilege level of 15.
    YOU MUST USE CISCO CP or the CISCO IOS CLI TO CHANGE THESE  PUBLICLY-KNOWN
    CREDENTIALS
    Here are the Cisco IOS commands.
    username <myuser>  privilege 15 secret 0 <mypassword>
    no username cisco
    Replace <myuser> and <mypassword> with the username and password you want
    to use.
    IF YOU DO NOT CHANGE THE PUBLICLY-KNOWN CREDENTIALS, YOU WILL NOT BE ABLE
    TO LOG INTO THE DEVICE AGAIN AFTER YOU HAVE LOGGED OFF.
    For more information about Cisco CP please follow the instructions in the
    QUICK START GUIDE for your router or go to http://www.cisco.com/go/ciscocp
    -----------------------------------------------------------------------
    ^C
    !
    line con 0
     login local
    line aux 0
    line 67
     no activation-character
     no exec
     transport preferred none
     transport input all
     transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
     stopbits 1
     flowcontrol software
    line vty 0 4
     privilege level 15
     login local
     transport input telnet
    line vty 5 15
     privilege level 15
     login local
     transport input telnet ssh
    !
    exception data-corruption buffer truncate
    scheduler allocate 20000 1000
    end

     
    Ken, Thanks for trying out the image for us. We are trying to reproduce this on our end but have had no luck so far. Can you please send us the output of show running-config from your router.



    Also we have one more image that we would like you to try it out before the debusg session would that be ok?



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Monday, November 01, 2010 10:22 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------

    Radhika,

    I tried the new OS and still getting same IOS crash.
    As mentioned I will work around your schedule so let me if you were able to get someone from the IOS team to help troubleshoot today.

    Thanks in advance,

    Ken Romo


    Ken,

    I am trying to get some help from the IOS team since this a router crash. So I will setup the webex session to debug for some time Monday so we can collect all the information and try out any suggestion from them.



    For Now We will post a newer IOS image to the beta Site and can you give that a try to see if that will solve the issue.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Friday, October 29, 2010 8:24 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    I will work around your schedule, anytime you are available, I will make myself available.
    email:
    kromo@opentext.com

    Thanks in advance,

    Ken Romo

    +++++++++++++++++++++++++++++++++

    Ken,

    Would a webex session tomorrow morning (any time between 10:00 and 1:00) work for you? Let me know the time that would work for you and also your email address so I can send you a webex invite.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Thursday, October 28, 2010 3:12 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Radhika Miriyala in Service Ready Engine Virtualizatio



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    No worries, we are trying to work this out together and I appreciate the help.
    s/m 1/1 is set as trunk but I went ahead and reconfigured to truank again and reloaded OS and get the same crash when I ping to the MGF interface from the SRE (I attached the errors at the bottom of this message).

    Ken,

    Sorry I just realized the mistake. I meant to say make the interface sm 1/1 as trunk.

    Sorry about the confusion.



    Please try it out.



    Thanks,

    Radhika



    boxer#
    %ALIGN-1-FATAL: Illegal access to a low address 22:02:10 UTC Thu Oct 28 2010
    addr=0x14, pc=0x22765BD8z , ra=0x22765B84z , sp=0x3022FBB8
    %ALIGN-1-FATAL: Illegal access to a low address 22:02:11 UTC Thu Oct 28 2010
    addr=0x14, pc=0x22765BD8z , ra=0x22765B84z , sp=0x3022FBB8

    22:02:11 UTC Thu Oct 28 2010: TLB (store) exception, CPU signal 10, PC = 0x22768478

    --------------------------------------------------------------------
    Possible software fault. Upon reccurence, please collect
    crashinfo, "show tech" and contact Cisco Technical Support.
    --------------------------------------------------------------------

    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z
    $0 : 00000000 00000000, AT : 00000000 29130000, v0 : 00000000 00000001, v1 : 00000000 0D8B8540
    a0 : 00000000 00000000, a1 : 00000000 0D8B8584, a2 : 00000000 2A2F8ABC, a3 : 00000000 00000004
    t0 : 00000000 00000020, t1 : 00000000 500099E1, t2 : 00000000 500081E0, t3 : FFFFFFFF FFFFFFF2
    t4 : 00000000 0000000E, t5 : 00000000 00000000, t6 : 00000000 0D95F890, t7 : 00000000 000001FF
    s0 : 00000000 00000000, s1 : 00000000 2A2FDB40, s2 : FFFFFFFF FFFFFFEC, s3 : 00000000 3080C980
    s4 : 00000000 0D95F89E, s5 : 00000000 2A300EE0, s6 : 00000000 00000000, s7 : 00000000 0000000E
    t8 : 00000000 000007FC, t9 : 00000000 2A300200, k0 : 00000000 00000000, k1 : 00000000 00000000
    gp : 00000000 29133C00, sp : 00000000 3022FBB8, s8 : 00000000 00000054, ra : 00000000 22768424
    EPC : 22768478, ErrorEPC : 80412AB4, SREG : 500099E3
    MDLO : 87126668, MDHI : D990ADBB, BadVaddr : 00000014
    CacheErr_Icache : 0x007F7F00 - 000040D8, CacheErr_Dcache : 0x00000000 - 00001FA0
    TagLo_Icache : 0x00000000 - 23642303, DataLo_Icache : 0xAFBF0018 - 0D81ADDB
    DataHi_Icache: 0x00000000 - 00000001
    TagLo_Dcache : 0x00000000 - 2277E583, TagHi_Dcache : 0x00000000 - 0912BD81
    DataLo_Dcache: 0x00000001 - 2368110C, DataHi_Dcache : 0x00000000 - 0000001C
    TEXT_START : 0x21003178
    DATA_START : 0x260888A0
    Cause 0000040C (Code 0x3): TLB (store) exception

    22:02:11 UTC Thu Oct 28 2010: TLB (store) exception, CPU signal 10, PC = 0x22768478

    --------------------------------------------------------------------
    Possible software fault. Upon reccurence, please collect
    crashinfo, "show tech" and contact Cisco Technical Support.
    --------------------------------------------------------------------

    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z
    $0 : 00000000 00000000, AT : 00000000 29130000, v0 : 00000000 00000001, v1 : 00000000 0D8B8540
    a0 : 00000000 00000000, a1 : 00000000 0D8B8584, a2 : 00000000 2A2F8ABC, a3 : 00000000 00000004
    t0 : 00000000 00000020, t1 : 00000000 500099E1, t2 : 00000000 500081E0, t3 : FFFFFFFF FFFFFFF2
    t4 : 00000000 0000000E, t5 : 00000000 00000000, t6 : 00000000 0D95F890, t7 : 00000000 000001FF
    s0 : 00000000 00000000, s1 : 00000000 2A2FDB40, s2 : FFFFFFFF FFFFFFEC, s3 : 00000000 3080C980
    s4 : 00000000 0D95F89E, s5 : 00000000 2A300EE0, s6 : 00000000 00000000, s7 : 00000000 0000000E
    t8 : 00000000 000007FC, t9 : 00000000 2A300200, k0 : 00000000 00000000, k1 : 00000000 00000000
    gp : 00000000 29133C00, sp : 00000000 3022FBB8, s8 : 00000000 00000054, ra : 00000000 22768424
    EPC : 22768478, ErrorEPC : 80412AB4, SREG : 500099E3
    MDLO : 87126668, MDHI : D990ADBB, BadVaddr : 00000014
    CacheErr_Icache : 0x007F7F00 - 000040D8, CacheErr_Dcache : 0x00000000 - 00001FA0
    TagLo_Icache : 0x00000000 - 23642303, DataLo_Icache : 0xAFBF0018 - 0D81ADDB
    DataHi_Icache: 0x00000000 - 00000001
    TagLo_Dcache : 0x00000000 - 2277E583, TagHi_Dcache : 0x00000000 - 0912BD81
    DataLo_Dcache: 0x00000001 - 2368110C, DataHi_Dcache : 0x00000000 - 0000001C
    TEXT_START : 0x21003178
    DATA_START : 0x260888A0
    Cause 0000040C (Code 0x3): TLB (store) exception
    Writing crashinfo to flash:crashinfo_20101028-220211-UTC
    22:02:11 UTC Thu Oct 28 2010: TLB (store) exception, CPU signal 10, PC = 0x22768478

    --------------------------------------------------------------------
    Possible software fault. Upon reccurence, please collect
    crashinfo, "show tech" and contact Cisco Technical Support.
    --------------------------------------------------------------------

    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z
    $0 : 00000000 00000000, AT : 00000000 29130000, v0 : 00000000 00000001, v1 : 00000000 0D8B8540
    a0 : 00000000 00000000, a1 : 00000000 0D8B8584, a2 : 00000000 2A2F8ABC, a3 : 00000000 00000004
    t0 : 00000000 00000020, t1 : 00000000 500099E1, t2 : 00000000 500081E0, t3 : FFFFFFFF FFFFFFF2
    t4 : 00000000 0000000E, t5 : 00000000 00000000, t6 : 00000000 0D95F890, t7 : 00000000 000001FF
    s0 : 00000000 00000000, s1 : 00000000 2A2FDB40, s2 : FFFFFFFF FFFFFFEC, s3 : 00000000 3080C980
    s4 : 00000000 0D95F89E, s5 : 00000000 2A300EE0, s6 : 00000000 00000000, s7 : 00000000 0000000E
    t8 : 00000000 000007FC, t9 : 00000000 2A300200, k0 : 00000000 00000000, k1 : 00000000 00000000
    gp : 00000000 29133C00, sp : 00000000 3022FBB8, s8 : 00000000 00000054, ra : 00000000 22768424
    EPC : 22768478, ErrorEPC : 80412AB4, SREG : 500099E3
    MDLO : 87126668, MDHI : D990ADBB, BadVaddr : 00000014
    CacheErr_Icache : 0x007F7F00 - 000040D8, CacheErr_Dcache : 0x00000000 - 00001FA0
    TagLo_Icache : 0x00000000 - 23642303, DataLo_Icache : 0xAFBF0018 - 0D81ADDB
    DataHi_Icache: 0x00000000 - 00000001
    TagLo_Dcache : 0x00000000 - 2277E583, TagHi_Dcache : 0x00000000 - 0912BD81
    DataLo_Dcache: 0x00000001 - 2368110C, DataHi_Dcache : 0x00000000 - 0000001C
    TEXT_START : 0x21003178
    DATA_START : 0x260888A0
    Cause 0000040C (Code 0x3): TLB (store) exception
    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z

    === Flushing messages (22:02:12 UTC Thu Oct 28 2010) ===
    Buffered messages:
    *Oct 28 20:52:40.075: %LINK-3-UPDOWN: Interface SM1/0, changed state to up
    *Oct 28 20:52:42.195: %LINK-3-UPDOWN: Interface GigabitEthernet0/0, changed state to up
    *Oct 28 20:52:42.195: %LINK-3-UPDOWN: Interface GigabitEthernet0/1, changed state to down
    *Oct 28 20:52:42.195: %LINK-3-UPDOWN: Interface GigabitEthernet0/2, changed state to down
    *Oct 28 20:52:44.631: %LINK-3-UPDOWN: Interface SM1/1, changed state to up
    *Oct 28 20:53:01.655: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/0, changed state to up
    *Oct 28 20:53:01.923: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/1, changed state to up
    *Oct 28 20:53:02.075: %LINK-3-UPDOWN: Interface Foreign Exchange Station 0/1/0, changed state to up
    *Oct 28 20:53:02.075: %LINK-3-UPDOWN: Interface Foreign Exchange Station 0/1/1, changed state to up
    *Oct 28 20:53:43.739: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/0, changed state to operational status down due to cable removal
    *Oct 28 20:53:44.739: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/1, changed state to operational status down due to cable removal
    Queued messages:
    No warm reboot Storage
    *** System received a Bus Error exception ***
    signal= 0xa, code= 0x40c, context= 0x29726b74
    PC = 0x22768478, SP = 0x3022fbb8, RA = 0x22768424
    Cause Reg = 0x0000040c, Status Reg = 0x500099e3
    System Bootstrap, Version 15.0(1r)M6, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 2010 by cisco Systems, Inc.
    Total memory size = 512 MB - On-board = 512 MB, DIMM0 = 0 MB
    CISCO2911/K9 platform with 524288 Kbytes of main memory
    Main memory is configured to 72/-1(On-board/DIMM0) bit mode with ECC enabled

    Readonly ROMMON initialized
    program load complete, entry point: 0x80803000, size: 0x1b340

    IOS Image Load Test
    ___________________
    Digitally Signed Development Software
    program load complete, entry point: 0x81000000, size: 0x40b6b74
    Self decompressing the image : #############################################################################################################

    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2691036>
    or simply reply to this email.
    -- --
    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2691978>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2699015>
    or simply reply to this email.


    Subject: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-
    Replied by: Radhika Miriyala on 20-11-2010 01:34:36 AM
    Thanks Ken. Can you also give us the output of the following.



    1)      show vlan-switch

    2)      ¿show platform mgf module¿ before the crash happens.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Monday, November 01, 2010 10:50 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    I will try whatever you suggest, just let me know when you have posted the new IOS.

    Below is my config:

    boxer#sh run
    Building configuration...

    Current configuration : 5777 bytes
    !
    version 15.1
    service timestamps debug datetime msec
    service timestamps log datetime msec
    no service password-encryption
    !
    hostname boxer
    !
    boot-start-marker
    boot system flash0 c2900-universalk9-mz.SSA.151-2.19.T
    boot-end-marker
    !
    !
    logging buffered 51200 warnings
    !
    no aaa new-model
    !
    no ipv6 cef
    ip source-route
    ip cef
    !
    !
    !
    !
    !
    ip domain name yourdomain.com
    multilink bundle-name authenticated
    !
    !
    !
    !
    !
    crypto pki token default removal timeout 0
    !
    crypto pki trustpoint TP-self-signed-1999750280
    enrollment selfsigned
    subject-name cn=IOS-Self-Signed-Certificate-1999750280
    revocation-check none
    rsakeypair TP-self-signed-1999750280
    !
    !
    crypto pki certificate chain TP-self-signed-1999750280
    certificate self-signed 01
      3082024C 308201B5 A0030201 02020101 300D0609 2A864886 F70D0101 04050030
      31312F30 2D060355 04031326 494F532D 53656C66 2D536967 6E65642D 43657274
      69666963 6174652D 31393939 37353032 3830301E 170D3130 31303230 32323335
      32365A17 0D323030 31303130 30303030 305A3031 312F302D 06035504 03132649
      4F532D53 656C662D 5369676E 65642D43 65727469 66696361 74652D31 39393937
      35303238 3030819F 300D0609 2A864886 F70D0101 01050003 818D0030 81890281
      81009378 2E139D79 DCA59865 14AB3398 870362B7 40BB9C13 A5DC5315 6108DF92
      5E78CF06 A40D4DB5 B66D410E FAFE75AC 764997B1 5C551A47 CFA00109 520352EC
      33A69E24 B3C1175B 136FC62A 8BE4637E B834059B FC7CAA6E 957DA0BB 66D8DC49
      80F82890 981FFCFE 0DC7E6F9 53287989 3887C5F6 AF59D0BE B502E11E FD16F556
      DBB90203 010001A3 74307230 0F060355 1D130101 FF040530 030101FF 301F0603
      551D1104 18301682 14626F78 65722E79 6F757264 6F6D6169 6E2E636F 6D301F06
      03551D23 04183016 80143541 7934E424 4B9A60DB E6C908C3 C20BAA17 D058301D
      0603551D 0E041604 14354179 34E4244B 9A60DBE6 C908C3C2 0BAA17D0 58300D06
      092A8648 86F70D01 01040500 03818100 3D222AB5 177D452F 153DCA26 1D7ECB49
      58BCBF60 DA18DC04 94B82EA3 76884EBC D7131641 08687C04 6C6645DF 78B2D2F8
      409BCAD7 50AF5091 B99614FD C2424D89 407A9109 BCA20473 F4CE33D4 4B126483
      C240C0B9 7A628E53 E419FEC3 B8853671 03113F5E 47FA8120 9F9A7A9D 11498FE0
      82C96578 8FD9770A EBD27F73 DF2E1487
            quit
    voice-card 0
    !
    !
    !
    !
    !
    !
    !
    license udi pid CISCO2911/K9 sn FTX1422A077
    hw-module pvdm 0/0
    !
    hw-module sm 1
    !
    !
    !
    username jack privilege 15 secret 5 $1$c5QR$fYGTbhWRKsBZ1JpNyIQGG1
    username marco privilege 15 secret 5 $1$amqq$5pI0T7mUViDL5Y.NqX/yz.
    !
    redundancy
    !
    !
    !
    !
    !
    !
    interface GigabitEthernet0/0
    description To tusqa network
    ip address 172.17.17.130 255.255.248.0
    duplex auto
    speed auto
    !
    interface GigabitEthernet0/1
    no ip address
    shutdown
    duplex auto
    speed auto
    !
    interface GigabitEthernet0/2
    no ip address
    shutdown
    duplex auto
    speed auto
    !
    interface SM1/0
    ip unnumbered GigabitEthernet0/0
    service-module ip address 172.17.17.129 255.255.248.0
    !Application: SRE-V Running on SMV
    service-module ip default-gateway 172.17.17.130
    service-module mgf ip address 10.62.64.1 255.255.255.0
    service-module mgf ip default-gateway 10.62.64.2
    !
    interface SM1/1
    description Internal switch interface connected to Service Module
    switchport mode trunk
    !
    interface Vlan1
    ip address 10.62.64.2 255.255.255.0
    !
    ip forward-protocol nd
    !
    ip http server
    ip http access-class 23
    ip http authentication local
    ip http secure-server
    ip http timeout-policy idle 60 life 86400 requests 10000
    !
    ip route 172.17.17.129 255.255.255.255 SM1/0
    !
    !
    !
    !
    control-plane
    !
    !
    voice-port 0/0/0
    !
    voice-port 0/0/1
    !
    voice-port 0/1/0
    !
    voice-port 0/1/1
    !
    !
    !
    mgcp profile default
    !
    !
    !
    !
    !
    gatekeeper
    shutdown
    !
    !
    banner exec ^C
    % Password expiration warning.
    -----------------------------------------------------------------------
    Cisco Configuration Professional (Cisco CP) is installed on this device
    and it provides the default username "cisco" for  one-time use. If you have
    already used the username "cisco" to login to the router and your IOS image
    supports the "one-time" user option, then this username has already expired.
    You will not be able to login to the router with this username after you exit
    this session.
    It is strongly suggested that you create a new username with a privilege level
    of 15 using the following command.
    username <myuser> privilege 15 secret 0 <mypassword>
    Replace <myuser> and <mypassword> with the username and password you want to
    use.
    -----------------------------------------------------------------------
    ^C
    banner login ^C
    -----------------------------------------------------------------------
    Cisco Configuration Professional (Cisco CP) is installed on this device.
    This feature requires the one-time use of the username "cisco" with the
    password "cisco". These default credentials have a privilege level of 15.
    YOU MUST USE CISCO CP or the CISCO IOS CLI TO CHANGE THESE  PUBLICLY-KNOWN
    CREDENTIALS
    Here are the Cisco IOS commands.
    username <myuser>  privilege 15 secret 0 <mypassword>
    no username cisco
    Replace <myuser> and <mypassword> with the username and password you want
    to use.
    IF YOU DO NOT CHANGE THE PUBLICLY-KNOWN CREDENTIALS, YOU WILL NOT BE ABLE
    TO LOG INTO THE DEVICE AGAIN AFTER YOU HAVE LOGGED OFF.
    For more information about Cisco CP please follow the instructions in the
    QUICK START GUIDE for your router or go to http://www.cisco.com/go/ciscocp
    -----------------------------------------------------------------------
    ^C
    !
    line con 0
    login local
    line aux 0
    line 67
    no activation-character
    no exec
    transport preferred none
    transport input all
    transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
    stopbits 1
    flowcontrol software
    line vty 0 4
    privilege level 15
    login local
    transport input telnet
    line vty 5 15
    privilege level 15
    login local
    transport input telnet ssh
    !
    exception data-corruption buffer truncate
    scheduler allocate 20000 1000
    end



    Ken, Thanks for trying out the image for us. We are trying to reproduce this on our end but have had no luck so far. Can you please send us the output of show running-config from your router.



    Also we have one more image that we would like you to try it out before the debusg session would that be ok?



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Monday, November 01, 2010 10:22 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------

    Radhika,

    I tried the new OS and still getting same IOS crash.
    As mentioned I will work around your schedule so let me if you were able to get someone from the IOS team to help troubleshoot today.

    Thanks in advance,

    Ken Romo


    Ken,

    I am trying to get some help from the IOS team since this a router crash. So I will setup the webex session to debug for some time Monday so we can collect all the information and try out any suggestion from them.



    For Now We will post a newer IOS image to the beta Site and can you give that a try to see if that will solve the issue.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Friday, October 29, 2010 8:24 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    I will work around your schedule, anytime you are available, I will make myself available.
    email:
    kromo@opentext.com

    Thanks in advance,

    Ken Romo

    +++++++++++++++++++++++++++++++++

    Ken,

    Would a webex session tomorrow morning (any time between 10:00 and 1:00) work for you? Let me know the time that would work for you and also your email address so I can send you a webex invite.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Thursday, October 28, 2010 3:12 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Radhika Miriyala in Service Ready Engine Virtualizatio



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    No worries, we are trying to work this out together and I appreciate the help.
    s/m 1/1 is set as trunk but I went ahead and reconfigured to truank again and reloaded OS and get the same crash when I ping to the MGF interface from the SRE (I attached the errors at the bottom of this message).

    Ken,

    Sorry I just realized the mistake. I meant to say make the interface sm 1/1 as trunk.

    Sorry about the confusion.



    Please try it out.



    Thanks,

    Radhika



    boxer#
    %ALIGN-1-FATAL: Illegal access to a low address 22:02:10 UTC Thu Oct 28 2010
    addr=0x14, pc=0x22765BD8z , ra=0x22765B84z , sp=0x3022FBB8
    %ALIGN-1-FATAL: Illegal access to a low address 22:02:11 UTC Thu Oct 28 2010
    addr=0x14, pc=0x22765BD8z , ra=0x22765B84z , sp=0x3022FBB8

    22:02:11 UTC Thu Oct 28 2010: TLB (store) exception, CPU signal 10, PC = 0x22768478

    --------------------------------------------------------------------
    Possible software fault. Upon reccurence, please collect
    crashinfo, "show tech" and contact Cisco Technical Support.
    --------------------------------------------------------------------

    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z
    $0 : 00000000 00000000, AT : 00000000 29130000, v0 : 00000000 00000001, v1 : 00000000 0D8B8540
    a0 : 00000000 00000000, a1 : 00000000 0D8B8584, a2 : 00000000 2A2F8ABC, a3 : 00000000 00000004
    t0 : 00000000 00000020, t1 : 00000000 500099E1, t2 : 00000000 500081E0, t3 : FFFFFFFF FFFFFFF2
    t4 : 00000000 0000000E, t5 : 00000000 00000000, t6 : 00000000 0D95F890, t7 : 00000000 000001FF
    s0 : 00000000 00000000, s1 : 00000000 2A2FDB40, s2 : FFFFFFFF FFFFFFEC, s3 : 00000000 3080C980
    s4 : 00000000 0D95F89E, s5 : 00000000 2A300EE0, s6 : 00000000 00000000, s7 : 00000000 0000000E
    t8 : 00000000 000007FC, t9 : 00000000 2A300200, k0 : 00000000 00000000, k1 : 00000000 00000000
    gp : 00000000 29133C00, sp : 00000000 3022FBB8, s8 : 00000000 00000054, ra : 00000000 22768424
    EPC : 22768478, ErrorEPC : 80412AB4, SREG : 500099E3
    MDLO : 87126668, MDHI : D990ADBB, BadVaddr : 00000014
    CacheErr_Icache : 0x007F7F00 - 000040D8, CacheErr_Dcache : 0x00000000 - 00001FA0
    TagLo_Icache : 0x00000000 - 23642303, DataLo_Icache : 0xAFBF0018 - 0D81ADDB
    DataHi_Icache: 0x00000000 - 00000001
    TagLo_Dcache : 0x00000000 - 2277E583, TagHi_Dcache : 0x00000000 - 0912BD81
    DataLo_Dcache: 0x00000001 - 2368110C, DataHi_Dcache : 0x00000000 - 0000001C
    TEXT_START : 0x21003178
    DATA_START : 0x260888A0
    Cause 0000040C (Code 0x3): TLB (store) exception

    22:02:11 UTC Thu Oct 28 2010: TLB (store) exception, CPU signal 10, PC = 0x22768478

    --------------------------------------------------------------------
    Possible software fault. Upon reccurence, please collect
    crashinfo, "show tech" and contact Cisco Technical Support.
    --------------------------------------------------------------------

    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z
    $0 : 00000000 00000000, AT : 00000000 29130000, v0 : 00000000 00000001, v1 : 00000000 0D8B8540
    a0 : 00000000 00000000, a1 : 00000000 0D8B8584, a2 : 00000000 2A2F8ABC, a3 : 00000000 00000004
    t0 : 00000000 00000020, t1 : 00000000 500099E1, t2 : 00000000 500081E0, t3 : FFFFFFFF FFFFFFF2
    t4 : 00000000 0000000E, t5 : 00000000 00000000, t6 : 00000000 0D95F890, t7 : 00000000 000001FF
    s0 : 00000000 00000000, s1 : 00000000 2A2FDB40, s2 : FFFFFFFF FFFFFFEC, s3 : 00000000 3080C980
    s4 : 00000000 0D95F89E, s5 : 00000000 2A300EE0, s6 : 00000000 00000000, s7 : 00000000 0000000E
    t8 : 00000000 000007FC, t9 : 00000000 2A300200, k0 : 00000000 00000000, k1 : 00000000 00000000
    gp : 00000000 29133C00, sp : 00000000 3022FBB8, s8 : 00000000 00000054, ra : 00000000 22768424
    EPC : 22768478, ErrorEPC : 80412AB4, SREG : 500099E3
    MDLO : 87126668, MDHI : D990ADBB, BadVaddr : 00000014
    CacheErr_Icache : 0x007F7F00 - 000040D8, CacheErr_Dcache : 0x00000000 - 00001FA0
    TagLo_Icache : 0x00000000 - 23642303, DataLo_Icache : 0xAFBF0018 - 0D81ADDB
    DataHi_Icache: 0x00000000 - 00000001
    TagLo_Dcache : 0x00000000 - 2277E583, TagHi_Dcache : 0x00000000 - 0912BD81
    DataLo_Dcache: 0x00000001 - 2368110C, DataHi_Dcache : 0x00000000 - 0000001C
    TEXT_START : 0x21003178
    DATA_START : 0x260888A0
    Cause 0000040C (Code 0x3): TLB (store) exception
    Writing crashinfo to flash:crashinfo_20101028-220211-UTC
    22:02:11 UTC Thu Oct 28 2010: TLB (store) exception, CPU signal 10, PC = 0x22768478

    --------------------------------------------------------------------
    Possible software fault. Upon reccurence, please collect
    crashinfo, "show tech" and contact Cisco Technical Support.
    --------------------------------------------------------------------

    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z
    $0 : 00000000 00000000, AT : 00000000 29130000, v0 : 00000000 00000001, v1 : 00000000 0D8B8540
    a0 : 00000000 00000000, a1 : 00000000 0D8B8584, a2 : 00000000 2A2F8ABC, a3 : 00000000 00000004
    t0 : 00000000 00000020, t1 : 00000000 500099E1, t2 : 00000000 500081E0, t3 : FFFFFFFF FFFFFFF2
    t4 : 00000000 0000000E, t5 : 00000000 00000000, t6 : 00000000 0D95F890, t7 : 00000000 000001FF
    s0 : 00000000 00000000, s1 : 00000000 2A2FDB40, s2 : FFFFFFFF FFFFFFEC, s3 : 00000000 3080C980
    s4 : 00000000 0D95F89E, s5 : 00000000 2A300EE0, s6 : 00000000 00000000, s7 : 00000000 0000000E
    t8 : 00000000 000007FC, t9 : 00000000 2A300200, k0 : 00000000 00000000, k1 : 00000000 00000000
    gp : 00000000 29133C00, sp : 00000000 3022FBB8, s8 : 00000000 00000054, ra : 00000000 22768424
    EPC : 22768478, ErrorEPC : 80412AB4, SREG : 500099E3
    MDLO : 87126668, MDHI : D990ADBB, BadVaddr : 00000014
    CacheErr_Icache : 0x007F7F00 - 000040D8, CacheErr_Dcache : 0x00000000 - 00001FA0
    TagLo_Icache : 0x00000000 - 23642303, DataLo_Icache : 0xAFBF0018 - 0D81ADDB
    DataHi_Icache: 0x00000000 - 00000001
    TagLo_Dcache : 0x00000000 - 2277E583, TagHi_Dcache : 0x00000000 - 0912BD81
    DataLo_Dcache: 0x00000001 - 2368110C, DataHi_Dcache : 0x00000000 - 0000001C
    TEXT_START : 0x21003178
    DATA_START : 0x260888A0
    Cause 0000040C (Code 0x3): TLB (store) exception
    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z

    === Flushing messages (22:02:12 UTC Thu Oct 28 2010) ===
    Buffered messages:
    *Oct 28 20:52:40.075: %LINK-3-UPDOWN: Interface SM1/0, changed state to up
    *Oct 28 20:52:42.195: %LINK-3-UPDOWN: Interface GigabitEthernet0/0, changed state to up
    *Oct 28 20:52:42.195: %LINK-3-UPDOWN: Interface GigabitEthernet0/1, changed state to down
    *Oct 28 20:52:42.195: %LINK-3-UPDOWN: Interface GigabitEthernet0/2, changed state to down
    *Oct 28 20:52:44.631: %LINK-3-UPDOWN: Interface SM1/1, changed state to up
    *Oct 28 20:53:01.655: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/0, changed state to up
    *Oct 28 20:53:01.923: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/1, changed state to up
    *Oct 28 20:53:02.075: %LINK-3-UPDOWN: Interface Foreign Exchange Station 0/1/0, changed state to up
    *Oct 28 20:53:02.075: %LINK-3-UPDOWN: Interface Foreign Exchange Station 0/1/1, changed state to up
    *Oct 28 20:53:43.739: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/0, changed state to operational status down due to cable removal
    *Oct 28 20:53:44.739: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/1, changed state to operational status down due to cable removal
    Queued messages:
    No warm reboot Storage
    *** System received a Bus Error exception ***
    signal= 0xa, code= 0x40c, context= 0x29726b74
    PC = 0x22768478, SP = 0x3022fbb8, RA = 0x22768424
    Cause Reg = 0x0000040c, Status Reg = 0x500099e3
    System Bootstrap, Version 15.0(1r)M6, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 2010 by cisco Systems, Inc.
    Total memory size = 512 MB - On-board = 512 MB, DIMM0 = 0 MB
    CISCO2911/K9 platform with 524288 Kbytes of main memory
    Main memory is configured to 72/-1(On-board/DIMM0) bit mode with ECC enabled

    Readonly ROMMON initialized
    program load complete, entry point: 0x80803000, size: 0x1b340

    IOS Image Load Test
    ___________________
    Digitally Signed Development Software
    program load complete, entry point: 0x81000000, size: 0x40b6b74
    Self decompressing the image : #############################################################################################################

    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2691036>
    or simply reply to this email.
    -- --
    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2691978>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2699015>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2699042>
    or simply reply to this email.

    Subject: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-
    Replied by: Ken Romo on 20-11-2010 01:34:36 AM
    Radhika,
     
    Here you go:
     
    boxer#show vlan-switch
    VLAN Name                             Status    Ports
    ---- -------------------------------- --------- -------------------------------
    1    default                          active
    1002 fddi-default                     act/unsup
    1003 token-ring-default               act/unsup
    1004 fddinet-default                  act/unsup
    1005 trnet-default                    act/unsup
    VLAN Type  SAID       MTU   Parent RingNo BridgeNo Stp  BrdgMode Trans1 Trans2
    ---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------
    1    enet  100001     1500  -      -      -        -    -        1002   1003
    1002 fddi  101002     1500  -      -      -        -    -        1      1003
    1003 tr    101003     1500  1005   0      -        -    srb      1      1002
    1004 fdnet 101004     1500  -      -      1        ibm  -        0      0
    1005 trnet 101005     1500  -      -      1        ibm  -        0      0
     
     
    boxer#sh platform mgf module
    Registered Module Information
    Code:   NR - Not Registered, TM - Trust Mode, SP - Scheduling Profile
            BL - Buffer Level, TR - Traffic Rate, PT - Pause Threshold
    slot    vlan    type/ID         TM      SP      BL      TR      PT
    ----    ----    ----------      ------- ---     ------  -----   ----
    ISM     NR
    EHWIC-0 NR
    EHWIC-1 NR
    EHWIC-2 NR
    EHWIC-3 NR
    PVDM-0  2       PVDM/5          UP      1       low     1000    low
    PVDM-1  2       PVDM/5          UP      1       low     1000    low
    SM-1    1       Switch/3        UP      1       low     1000    high

     
     
    Thanks Ken. Can you also give us the output of the following.



    1) show vlan-switch

    2) ¿show platform mgf module¿ before the crash happens.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Monday, November 01, 2010 10:50 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    I will try whatever you suggest, just let me know when you have posted the new IOS.

    Below is my config:

    boxer#sh run
    Building configuration...

    Current configuration : 5777 bytes
    !
    version 15.1
    service timestamps debug datetime msec
    service timestamps log datetime msec
    no service password-encryption
    !
    hostname boxer
    !
    boot-start-marker
    boot system flash0 c2900-universalk9-mz.SSA.151-2.19.T
    boot-end-marker
    !
    !
    logging buffered 51200 warnings
    !
    no aaa new-model
    !
    no ipv6 cef
    ip source-route
    ip cef
    !
    !
    !
    !
    !
    ip domain name yourdomain.com
    multilink bundle-name authenticated
    !
    !
    !
    !
    !
    crypto pki token default removal timeout 0
    !
    crypto pki trustpoint TP-self-signed-1999750280
    enrollment selfsigned
    subject-name cn=IOS-Self-Signed-Certificate-1999750280
    revocation-check none
    rsakeypair TP-self-signed-1999750280
    !
    !
    crypto pki certificate chain TP-self-signed-1999750280
    certificate self-signed 01
    3082024C 308201B5 A0030201 02020101 300D0609 2A864886 F70D0101 04050030
    31312F30 2D060355 04031326 494F532D 53656C66 2D536967 6E65642D 43657274
    69666963 6174652D 31393939 37353032 3830301E 170D3130 31303230 32323335
    32365A17 0D323030 31303130 30303030 305A3031 312F302D 06035504 03132649
    4F532D53 656C662D 5369676E 65642D43 65727469 66696361 74652D31 39393937
    35303238 3030819F 300D0609 2A864886 F70D0101 01050003 818D0030 81890281
    81009378 2E139D79 DCA59865 14AB3398 870362B7 40BB9C13 A5DC5315 6108DF92
    5E78CF06 A40D4DB5 B66D410E FAFE75AC 764997B1 5C551A47 CFA00109 520352EC
    33A69E24 B3C1175B 136FC62A 8BE4637E B834059B FC7CAA6E 957DA0BB 66D8DC49
    80F82890 981FFCFE 0DC7E6F9 53287989 3887C5F6 AF59D0BE B502E11E FD16F556
    DBB90203 010001A3 74307230 0F060355 1D130101 FF040530 030101FF 301F0603
    551D1104 18301682 14626F78 65722E79 6F757264 6F6D6169 6E2E636F 6D301F06
    03551D23 04183016 80143541 7934E424 4B9A60DB E6C908C3 C20BAA17 D058301D
    0603551D 0E041604 14354179 34E4244B 9A60DBE6 C908C3C2 0BAA17D0 58300D06
    092A8648 86F70D01 01040500 03818100 3D222AB5 177D452F 153DCA26 1D7ECB49
    58BCBF60 DA18DC04 94B82EA3 76884EBC D7131641 08687C04 6C6645DF 78B2D2F8
    409BCAD7 50AF5091 B99614FD C2424D89 407A9109 BCA20473 F4CE33D4 4B126483
    C240C0B9 7A628E53 E419FEC3 B8853671 03113F5E 47FA8120 9F9A7A9D 11498FE0
    82C96578 8FD9770A EBD27F73 DF2E1487
    quit
    voice-card 0
    !
    !
    !
    !
    !
    !
    !
    license udi pid CISCO2911/K9 sn FTX1422A077
    hw-module pvdm 0/0
    !
    hw-module sm 1
    !
    !
    !
    username jack privilege 15 secret 5 $1$c5QR$fYGTbhWRKsBZ1JpNyIQGG1
    username marco privilege 15 secret 5 $1$amqq$5pI0T7mUViDL5Y.NqX/yz.
    !
    redundancy
    !
    !
    !
    !
    !
    !
    interface GigabitEthernet0/0
    description To tusqa network
    ip address 172.17.17.130 255.255.248.0
    duplex auto
    speed auto
    !
    interface GigabitEthernet0/1
    no ip address
    shutdown
    duplex auto
    speed auto
    !
    interface GigabitEthernet0/2
    no ip address
    shutdown
    duplex auto
    speed auto
    !
    interface SM1/0
    ip unnumbered GigabitEthernet0/0
    service-module ip address 172.17.17.129 255.255.248.0
    !Application: SRE-V Running on SMV
    service-module ip default-gateway 172.17.17.130
    service-module mgf ip address 10.62.64.1 255.255.255.0
    service-module mgf ip default-gateway 10.62.64.2
    !
    interface SM1/1
    description Internal switch interface connected to Service Module
    switchport mode trunk
    !
    interface Vlan1
    ip address 10.62.64.2 255.255.255.0
    !
    ip forward-protocol nd
    !
    ip http server
    ip http access-class 23
    ip http authentication local
    ip http secure-server
    ip http timeout-policy idle 60 life 86400 requests 10000
    !
    ip route 172.17.17.129 255.255.255.255 SM1/0
    !
    !
    !
    !
    control-plane
    !
    !
    voice-port 0/0/0
    !
    voice-port 0/0/1
    !
    voice-port 0/1/0
    !
    voice-port 0/1/1
    !
    !
    !
    mgcp profile default
    !
    !
    !
    !
    !
    gatekeeper
    shutdown
    !
    !
    banner exec ^C
    % Password expiration warning.
    -----------------------------------------------------------------------
    Cisco Configuration Professional (Cisco CP) is installed on this device
    and it provides the default username "cisco" for one-time use. If you have
    already used the username "cisco" to login to the router and your IOS image
    supports the "one-time" user option, then this username has already expired.
    You will not be able to login to the router with this username after you exit
    this session.
    It is strongly suggested that you create a new username with a privilege level
    of 15 using the following command.
    username <myuser> privilege 15 secret 0 <mypassword>
    Replace <myuser> and <mypassword> with the username and password you want to
    use.
    -----------------------------------------------------------------------
    ^C
    banner login ^C
    -----------------------------------------------------------------------
    Cisco Configuration Professional (Cisco CP) is installed on this device.
    This feature requires the one-time use of the username "cisco" with the
    password "cisco". These default credentials have a privilege level of 15.
    YOU MUST USE CISCO CP or the CISCO IOS CLI TO CHANGE THESE PUBLICLY-KNOWN
    CREDENTIALS
    Here are the Cisco IOS commands.
    username <myuser> privilege 15 secret 0 <mypassword>
    no username cisco
    Replace <myuser> and <mypassword> with the username and password you want
    to use.
    IF YOU DO NOT CHANGE THE PUBLICLY-KNOWN CREDENTIALS, YOU WILL NOT BE ABLE
    TO LOG INTO THE DEVICE AGAIN AFTER YOU HAVE LOGGED OFF.
    For more information about Cisco CP please follow the instructions in the
    QUICK START GUIDE for your router or go to http://www.cisco.com/go/ciscocp
    -----------------------------------------------------------------------
    ^C
    !
    line con 0
    login local
    line aux 0
    line 67
    no activation-character
    no exec
    transport preferred none
    transport input all
    transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
    stopbits 1
    flowcontrol software
    line vty 0 4
    privilege level 15
    login local
    transport input telnet
    line vty 5 15
    privilege level 15
    login local
    transport input telnet ssh
    !
    exception data-corruption buffer truncate
    scheduler allocate 20000 1000
    end



    Ken, Thanks for trying out the image for us. We are trying to reproduce this on our end but have had no luck so far. Can you please send us the output of show running-config from your router.



    Also we have one more image that we would like you to try it out before the debusg session would that be ok?



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Monday, November 01, 2010 10:22 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------

    Radhika,

    I tried the new OS and still getting same IOS crash.
    As mentioned I will work around your schedule so let me if you were able to get someone from the IOS team to help troubleshoot today.

    Thanks in advance,

    Ken Romo


    Ken,

    I am trying to get some help from the IOS team since this a router crash. So I will setup the webex session to debug for some time Monday so we can collect all the information and try out any suggestion from them.



    For Now We will post a newer IOS image to the beta Site and can you give that a try to see if that will solve the issue.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Friday, October 29, 2010 8:24 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    I will work around your schedule, anytime you are available, I will make myself available.
    email:
    kromo@opentext.com

    Thanks in advance,

    Ken Romo

    +++++++++++++++++++++++++++++++++

    Ken,

    Would a webex session tomorrow morning (any time between 10:00 and 1:00) work for you? Let me know the time that would work for you and also your email address so I can send you a webex invite.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Thursday, October 28, 2010 3:12 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Radhika Miriyala in Service Ready Engine Virtualizatio



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    No worries, we are trying to work this out together and I appreciate the help.
    s/m 1/1 is set as trunk but I went ahead and reconfigured to truank again and reloaded OS and get the same crash when I ping to the MGF interface from the SRE (I attached the errors at the bottom of this message).

    Ken,

    Sorry I just realized the mistake. I meant to say make the interface sm 1/1 as trunk.

    Sorry about the confusion.



    Please try it out.



    Thanks,

    Radhika



    boxer#
    %ALIGN-1-FATAL: Illegal access to a low address 22:02:10 UTC Thu Oct 28 2010
    addr=0x14, pc=0x22765BD8z , ra=0x22765B84z , sp=0x3022FBB8
    %ALIGN-1-FATAL: Illegal access to a low address 22:02:11 UTC Thu Oct 28 2010
    addr=0x14, pc=0x22765BD8z , ra=0x22765B84z , sp=0x3022FBB8

    22:02:11 UTC Thu Oct 28 2010: TLB (store) exception, CPU signal 10, PC = 0x22768478

    --------------------------------------------------------------------
    Possible software fault. Upon reccurence, please collect
    crashinfo, "show tech" and contact Cisco Technical Support.
    --------------------------------------------------------------------

    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z
    $0 : 00000000 00000000, AT : 00000000 29130000, v0 : 00000000 00000001, v1 : 00000000 0D8B8540
    a0 : 00000000 00000000, a1 : 00000000 0D8B8584, a2 : 00000000 2A2F8ABC, a3 : 00000000 00000004
    t0 : 00000000 00000020, t1 : 00000000 500099E1, t2 : 00000000 500081E0, t3 : FFFFFFFF FFFFFFF2
    t4 : 00000000 0000000E, t5 : 00000000 00000000, t6 : 00000000 0D95F890, t7 : 00000000 000001FF
    s0 : 00000000 00000000, s1 : 00000000 2A2FDB40, s2 : FFFFFFFF FFFFFFEC, s3 : 00000000 3080C980
    s4 : 00000000 0D95F89E, s5 : 00000000 2A300EE0, s6 : 00000000 00000000, s7 : 00000000 0000000E
    t8 : 00000000 000007FC, t9 : 00000000 2A300200, k0 : 00000000 00000000, k1 : 00000000 00000000
    gp : 00000000 29133C00, sp : 00000000 3022FBB8, s8 : 00000000 00000054, ra : 00000000 22768424
    EPC : 22768478, ErrorEPC : 80412AB4, SREG : 500099E3
    MDLO : 87126668, MDHI : D990ADBB, BadVaddr : 00000014
    CacheErr_Icache : 0x007F7F00 - 000040D8, CacheErr_Dcache : 0x00000000 - 00001FA0
    TagLo_Icache : 0x00000000 - 23642303, DataLo_Icache : 0xAFBF0018 - 0D81ADDB
    DataHi_Icache: 0x00000000 - 00000001
    TagLo_Dcache : 0x00000000 - 2277E583, TagHi_Dcache : 0x00000000 - 0912BD81
    DataLo_Dcache: 0x00000001 - 2368110C, DataHi_Dcache : 0x00000000 - 0000001C
    TEXT_START : 0x21003178
    DATA_START : 0x260888A0
    Cause 0000040C (Code 0x3): TLB (store) exception

    22:02:11 UTC Thu Oct 28 2010: TLB (store) exception, CPU signal 10, PC = 0x22768478

    --------------------------------------------------------------------
    Possible software fault. Upon reccurence, please collect
    crashinfo, "show tech" and contact Cisco Technical Support.
    --------------------------------------------------------------------

    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z
    $0 : 00000000 00000000, AT : 00000000 29130000, v0 : 00000000 00000001, v1 : 00000000 0D8B8540
    a0 : 00000000 00000000, a1 : 00000000 0D8B8584, a2 : 00000000 2A2F8ABC, a3 : 00000000 00000004
    t0 : 00000000 00000020, t1 : 00000000 500099E1, t2 : 00000000 500081E0, t3 : FFFFFFFF FFFFFFF2
    t4 : 00000000 0000000E, t5 : 00000000 00000000, t6 : 00000000 0D95F890, t7 : 00000000 000001FF
    s0 : 00000000 00000000, s1 : 00000000 2A2FDB40, s2 : FFFFFFFF FFFFFFEC, s3 : 00000000 3080C980
    s4 : 00000000 0D95F89E, s5 : 00000000 2A300EE0, s6 : 00000000 00000000, s7 : 00000000 0000000E
    t8 : 00000000 000007FC, t9 : 00000000 2A300200, k0 : 00000000 00000000, k1 : 00000000 00000000
    gp : 00000000 29133C00, sp : 00000000 3022FBB8, s8 : 00000000 00000054, ra : 00000000 22768424
    EPC : 22768478, ErrorEPC : 80412AB4, SREG : 500099E3
    MDLO : 87126668, MDHI : D990ADBB, BadVaddr : 00000014
    CacheErr_Icache : 0x007F7F00 - 000040D8, CacheErr_Dcache : 0x00000000 - 00001FA0
    TagLo_Icache : 0x00000000 - 23642303, DataLo_Icache : 0xAFBF0018 - 0D81ADDB
    DataHi_Icache: 0x00000000 - 00000001
    TagLo_Dcache : 0x00000000 - 2277E583, TagHi_Dcache : 0x00000000 - 0912BD81
    DataLo_Dcache: 0x00000001 - 2368110C, DataHi_Dcache : 0x00000000 - 0000001C
    TEXT_START : 0x21003178
    DATA_START : 0x260888A0
    Cause 0000040C (Code 0x3): TLB (store) exception
    Writing crashinfo to flash:crashinfo_20101028-220211-UTC
    22:02:11 UTC Thu Oct 28 2010: TLB (store) exception, CPU signal 10, PC = 0x22768478

    --------------------------------------------------------------------
    Possible software fault. Upon reccurence, please collect
    crashinfo, "show tech" and contact Cisco Technical Support.
    --------------------------------------------------------------------

    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z
    $0 : 00000000 00000000, AT : 00000000 29130000, v0 : 00000000 00000001, v1 : 00000000 0D8B8540
    a0 : 00000000 00000000, a1 : 00000000 0D8B8584, a2 : 00000000 2A2F8ABC, a3 : 00000000 00000004
    t0 : 00000000 00000020, t1 : 00000000 500099E1, t2 : 00000000 500081E0, t3 : FFFFFFFF FFFFFFF2
    t4 : 00000000 0000000E, t5 : 00000000 00000000, t6 : 00000000 0D95F890, t7 : 00000000 000001FF
    s0 : 00000000 00000000, s1 : 00000000 2A2FDB40, s2 : FFFFFFFF FFFFFFEC, s3 : 00000000 3080C980
    s4 : 00000000 0D95F89E, s5 : 00000000 2A300EE0, s6 : 00000000 00000000, s7 : 00000000 0000000E
    t8 : 00000000 000007FC, t9 : 00000000 2A300200, k0 : 00000000 00000000, k1 : 00000000 00000000
    gp : 00000000 29133C00, sp : 00000000 3022FBB8, s8 : 00000000 00000054, ra : 00000000 22768424
    EPC : 22768478, ErrorEPC : 80412AB4, SREG : 500099E3
    MDLO : 87126668, MDHI : D990ADBB, BadVaddr : 00000014
    CacheErr_Icache : 0x007F7F00 - 000040D8, CacheErr_Dcache : 0x00000000 - 00001FA0
    TagLo_Icache : 0x00000000 - 23642303, DataLo_Icache : 0xAFBF0018 - 0D81ADDB
    DataHi_Icache: 0x00000000 - 00000001
    TagLo_Dcache : 0x00000000 - 2277E583, TagHi_Dcache : 0x00000000 - 0912BD81
    DataLo_Dcache: 0x00000001 - 2368110C, DataHi_Dcache : 0x00000000 - 0000001C
    TEXT_START : 0x21003178
    DATA_START : 0x260888A0
    Cause 0000040C (Code 0x3): TLB (store) exception
    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z

    === Flushing messages (22:02:12 UTC Thu Oct 28 2010) ===
    Buffered messages:
    *Oct 28 20:52:40.075: %LINK-3-UPDOWN: Interface SM1/0, changed state to up
    *Oct 28 20:52:42.195: %LINK-3-UPDOWN: Interface GigabitEthernet0/0, changed state to up
    *Oct 28 20:52:42.195: %LINK-3-UPDOWN: Interface GigabitEthernet0/1, changed state to down
    *Oct 28 20:52:42.195: %LINK-3-UPDOWN: Interface GigabitEthernet0/2, changed state to down
    *Oct 28 20:52:44.631: %LINK-3-UPDOWN: Interface SM1/1, changed state to up
    *Oct 28 20:53:01.655: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/0, changed state to up
    *Oct 28 20:53:01.923: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/1, changed state to up
    *Oct 28 20:53:02.075: %LINK-3-UPDOWN: Interface Foreign Exchange Station 0/1/0, changed state to up
    *Oct 28 20:53:02.075: %LINK-3-UPDOWN: Interface Foreign Exchange Station 0/1/1, changed state to up
    *Oct 28 20:53:43.739: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/0, changed state to operational status down due to cable removal
    *Oct 28 20:53:44.739: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/1, changed state to operational status down due to cable removal
    Queued messages:
    No warm reboot Storage
    *** System received a Bus Error exception ***
    signal= 0xa, code= 0x40c, context= 0x29726b74
    PC = 0x22768478, SP = 0x3022fbb8, RA = 0x22768424
    Cause Reg = 0x0000040c, Status Reg = 0x500099e3
    System Bootstrap, Version 15.0(1r)M6, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 2010 by cisco Systems, Inc.
    Total memory size = 512 MB - On-board = 512 MB, DIMM0 = 0 MB
    CISCO2911/K9 platform with 524288 Kbytes of main memory
    Main memory is configured to 72/-1(On-board/DIMM0) bit mode with ECC enabled

    Readonly ROMMON initialized
    program load complete, entry point: 0x80803000, size: 0x1b340

    IOS Image Load Test
    ___________________
    Digitally Signed Development Software
    program load complete, entry point: 0x81000000, size: 0x40b6b74
    Self decompressing the image : #############################################################################################################

    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2691036>
    or simply reply to this email.
    -- --
    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2691978>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2699015>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2699042>
    or simply reply to this email.


    Subject: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-
    Replied by: Radhika Miriyala on 20-11-2010 01:34:36 AM
    Ken,

    Please try out the new image sent by Brett to you when you get a chance.  Also one difference we noticed is that you have PVDM¿s in your setup that we don not have in our test setup. Would it be possible to remove the PVDMS temporarily and try the ping? This may help us root cause the issue.



    I will also schedule a WebEx for tomorrow morning 10:30 PST with the IOS developer so we can take a look if the change of IOS image and removal of PVDM¿s does not solve the issue. Please let me know if that time slot does not work for you.



    Thanks,

    Radhika





    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Monday, November 01, 2010 11:19 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    Here you go:

    boxer#show vlan-switch
    VLAN Name                             Status    Ports
    ---- -------------------------------- --------- -------------------------------
    1    default                          active
    1002 fddi-default                     act/unsup
    1003 token-ring-default               act/unsup
    1004 fddinet-default                  act/unsup
    1005 trnet-default                    act/unsup
    VLAN Type  SAID       MTU   Parent RingNo BridgeNo Stp  BrdgMode Trans1 Trans2
    ---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------
    1    enet  100001     1500  -      -      -        -    -        1002   1003
    1002 fddi  101002     1500  -      -      -        -    -        1      1003
    1003 tr    101003     1500  1005   0      -        -    srb      1      1002
    1004 fdnet 101004     1500  -      -      1        ibm  -        0      0
    1005 trnet 101005     1500  -      -      1        ibm  -        0      0


    boxer#sh platform mgf module
    Registered Module Information
    Code:   NR - Not Registered, TM - Trust Mode, SP - Scheduling Profile
            BL - Buffer Level, TR - Traffic Rate, PT - Pause Threshold
    slot    vlan    type/ID         TM      SP      BL      TR      PT
    ----    ----    ----------      ------- ---     ------  -----   ----
    ISM     NR
    EHWIC-0 NR
    EHWIC-1 NR
    EHWIC-2 NR
    EHWIC-3 NR
    PVDM-0  2       PVDM/5          UP      1       low     1000    low
    PVDM-1  2       PVDM/5          UP      1       low     1000    low
    SM-1    1       Switch/3        UP      1       low     1000    high




    Thanks Ken. Can you also give us the output of the following.



    1) show vlan-switch

    2) ¿show platform mgf module¿ before the crash happens.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Monday, November 01, 2010 10:50 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    I will try whatever you suggest, just let me know when you have posted the new IOS.

    Below is my config:

    boxer#sh run
    Building configuration...

    Current configuration : 5777 bytes
    !
    version 15.1
    service timestamps debug datetime msec
    service timestamps log datetime msec
    no service password-encryption
    !
    hostname boxer
    !
    boot-start-marker
    boot system flash0 c2900-universalk9-mz.SSA.151-2.19.T
    boot-end-marker
    !
    !
    logging buffered 51200 warnings
    !
    no aaa new-model
    !
    no ipv6 cef
    ip source-route
    ip cef
    !
    !
    !
    !
    !
    ip domain name yourdomain.com
    multilink bundle-name authenticated
    !
    !
    !
    !
    !
    crypto pki token default removal timeout 0
    !
    crypto pki trustpoint TP-self-signed-1999750280
    enrollment selfsigned
    subject-name cn=IOS-Self-Signed-Certificate-1999750280
    revocation-check none
    rsakeypair TP-self-signed-1999750280
    !
    !
    crypto pki certificate chain TP-self-signed-1999750280
    certificate self-signed 01
    3082024C 308201B5 A0030201 02020101 300D0609 2A864886 F70D0101 04050030
    31312F30 2D060355 04031326 494F532D 53656C66 2D536967 6E65642D 43657274
    69666963 6174652D 31393939 37353032 3830301E 170D3130 31303230 32323335
    32365A17 0D323030 31303130 30303030 305A3031 312F302D 06035504 03132649
    4F532D53 656C662D 5369676E 65642D43 65727469 66696361 74652D31 39393937
    35303238 3030819F 300D0609 2A864886 F70D0101 01050003 818D0030 81890281
    81009378 2E139D79 DCA59865 14AB3398 870362B7 40BB9C13 A5DC5315 6108DF92
    5E78CF06 A40D4DB5 B66D410E FAFE75AC 764997B1 5C551A47 CFA00109 520352EC
    33A69E24 B3C1175B 136FC62A 8BE4637E B834059B FC7CAA6E 957DA0BB 66D8DC49
    80F82890 981FFCFE 0DC7E6F9 53287989 3887C5F6 AF59D0BE B502E11E FD16F556
    DBB90203 010001A3 74307230 0F060355 1D130101 FF040530 030101FF 301F0603
    551D1104 18301682 14626F78 65722E79 6F757264 6F6D6169 6E2E636F 6D301F06
    03551D23 04183016 80143541 7934E424 4B9A60DB E6C908C3 C20BAA17 D058301D
    0603551D 0E041604 14354179 34E4244B 9A60DBE6 C908C3C2 0BAA17D0 58300D06
    092A8648 86F70D01 01040500 03818100 3D222AB5 177D452F 153DCA26 1D7ECB49
    58BCBF60 DA18DC04 94B82EA3 76884EBC D7131641 08687C04 6C6645DF 78B2D2F8
    409BCAD7 50AF5091 B99614FD C2424D89 407A9109 BCA20473 F4CE33D4 4B126483
    C240C0B9 7A628E53 E419FEC3 B8853671 03113F5E 47FA8120 9F9A7A9D 11498FE0
    82C96578 8FD9770A EBD27F73 DF2E1487
    quit
    voice-card 0
    !
    !
    !
    !
    !
    !
    !
    license udi pid CISCO2911/K9 sn FTX1422A077
    hw-module pvdm 0/0
    !
    hw-module sm 1
    !
    !
    !
    username jack privilege 15 secret 5 $1$c5QR$fYGTbhWRKsBZ1JpNyIQGG1
    username marco privilege 15 secret 5 $1$amqq$5pI0T7mUViDL5Y.NqX/yz.
    !
    redundancy
    !
    !
    !
    !
    !
    !
    interface GigabitEthernet0/0
    description To tusqa network
    ip address 172.17.17.130 255.255.248.0
    duplex auto
    speed auto
    !
    interface GigabitEthernet0/1
    no ip address
    shutdown
    duplex auto
    speed auto
    !
    interface GigabitEthernet0/2
    no ip address
    shutdown
    duplex auto
    speed auto
    !
    interface SM1/0
    ip unnumbered GigabitEthernet0/0
    service-module ip address 172.17.17.129 255.255.248.0
    !Application: SRE-V Running on SMV
    service-module ip default-gateway 172.17.17.130
    service-module mgf ip address 10.62.64.1 255.255.255.0
    service-module mgf ip default-gateway 10.62.64.2
    !
    interface SM1/1
    description Internal switch interface connected to Service Module
    switchport mode trunk
    !
    interface Vlan1
    ip address 10.62.64.2 255.255.255.0
    !
    ip forward-protocol nd
    !
    ip http server
    ip http access-class 23
    ip http authentication local
    ip http secure-server
    ip http timeout-policy idle 60 life 86400 requests 10000
    !
    ip route 172.17.17.129 255.255.255.255 SM1/0
    !
    !
    !
    !
    control-plane
    !
    !
    voice-port 0/0/0
    !
    voice-port 0/0/1
    !
    voice-port 0/1/0
    !
    voice-port 0/1/1
    !
    !
    !
    mgcp profile default
    !
    !
    !
    !
    !
    gatekeeper
    shutdown
    !
    !
    banner exec ^C
    % Password expiration warning.
    -----------------------------------------------------------------------
    Cisco Configuration Professional (Cisco CP) is installed on this device
    and it provides the default username "cisco" for one-time use. If you have
    already used the username "cisco" to login to the router and your IOS image
    supports the "one-time" user option, then this username has already expired.
    You will not be able to login to the router with this username after you exit
    this session.
    It is strongly suggested that you create a new username with a privilege level
    of 15 using the following command.
    username <myuser> privilege 15 secret 0 <mypassword>
    Replace <myuser> and <mypassword> with the username and password you want to
    use.
    -----------------------------------------------------------------------
    ^C
    banner login ^C
    -----------------------------------------------------------------------
    Cisco Configuration Professional (Cisco CP) is installed on this device.
    This feature requires the one-time use of the username "cisco" with the
    password "cisco". These default credentials have a privilege level of 15.
    YOU MUST USE CISCO CP or the CISCO IOS CLI TO CHANGE THESE PUBLICLY-KNOWN
    CREDENTIALS
    Here are the Cisco IOS commands.
    username <myuser> privilege 15 secret 0 <mypassword>
    no username cisco
    Replace <myuser> and <mypassword> with the username and password you want
    to use.
    IF YOU DO NOT CHANGE THE PUBLICLY-KNOWN CREDENTIALS, YOU WILL NOT BE ABLE
    TO LOG INTO THE DEVICE AGAIN AFTER YOU HAVE LOGGED OFF.
    For more information about Cisco CP please follow the instructions in the
    QUICK START GUIDE for your router or go to http://www.cisco.com/go/ciscocp
    -----------------------------------------------------------------------
    ^C
    !
    line con 0
    login local
    line aux 0
    line 67
    no activation-character
    no exec
    transport preferred none
    transport input all
    transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
    stopbits 1
    flowcontrol software
    line vty 0 4
    privilege level 15
    login local
    transport input telnet
    line vty 5 15
    privilege level 15
    login local
    transport input telnet ssh
    !
    exception data-corruption buffer truncate
    scheduler allocate 20000 1000
    end



    Ken, Thanks for trying out the image for us. We are trying to reproduce this on our end but have had no luck so far. Can you please send us the output of show running-config from your router.



    Also we have one more image that we would like you to try it out before the debusg session would that be ok?



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Monday, November 01, 2010 10:22 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------

    Radhika,

    I tried the new OS and still getting same IOS crash.
    As mentioned I will work around your schedule so let me if you were able to get someone from the IOS team to help troubleshoot today.

    Thanks in advance,

    Ken Romo


    Ken,

    I am trying to get some help from the IOS team since this a router crash. So I will setup the webex session to debug for some time Monday so we can collect all the information and try out any suggestion from them.



    For Now We will post a newer IOS image to the beta Site and can you give that a try to see if that will solve the issue.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Friday, October 29, 2010 8:24 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    I will work around your schedule, anytime you are available, I will make myself available.
    email:
    kromo@opentext.com

    Thanks in advance,

    Ken Romo

    +++++++++++++++++++++++++++++++++

    Ken,

    Would a webex session tomorrow morning (any time between 10:00 and 1:00) work for you? Let me know the time that would work for you and also your email address so I can send you a webex invite.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Thursday, October 28, 2010 3:12 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Radhika Miriyala in Service Ready Engine Virtualizatio



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    No worries, we are trying to work this out together and I appreciate the help.
    s/m 1/1 is set as trunk but I went ahead and reconfigured to truank again and reloaded OS and get the same crash when I ping to the MGF interface from the SRE (I attached the errors at the bottom of this message).

    Ken,

    Sorry I just realized the mistake. I meant to say make the interface sm 1/1 as trunk.

    Sorry about the confusion.



    Please try it out.



    Thanks,

    Radhika



    boxer#
    %ALIGN-1-FATAL: Illegal access to a low address 22:02:10 UTC Thu Oct 28 2010
    addr=0x14, pc=0x22765BD8z , ra=0x22765B84z , sp=0x3022FBB8
    %ALIGN-1-FATAL: Illegal access to a low address 22:02:11 UTC Thu Oct 28 2010
    addr=0x14, pc=0x22765BD8z , ra=0x22765B84z , sp=0x3022FBB8

    22:02:11 UTC Thu Oct 28 2010: TLB (store) exception, CPU signal 10, PC = 0x22768478

    --------------------------------------------------------------------
    Possible software fault. Upon reccurence, please collect
    crashinfo, "show tech" and contact Cisco Technical Support.
    --------------------------------------------------------------------

    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z
    $0 : 00000000 00000000, AT : 00000000 29130000, v0 : 00000000 00000001, v1 : 00000000 0D8B8540
    a0 : 00000000 00000000, a1 : 00000000 0D8B8584, a2 : 00000000 2A2F8ABC, a3 : 00000000 00000004
    t0 : 00000000 00000020, t1 : 00000000 500099E1, t2 : 00000000 500081E0, t3 : FFFFFFFF FFFFFFF2
    t4 : 00000000 0000000E, t5 : 00000000 00000000, t6 : 00000000 0D95F890, t7 : 00000000 000001FF
    s0 : 00000000 00000000, s1 : 00000000 2A2FDB40, s2 : FFFFFFFF FFFFFFEC, s3 : 00000000 3080C980
    s4 : 00000000 0D95F89E, s5 : 00000000 2A300EE0, s6 : 00000000 00000000, s7 : 00000000 0000000E
    t8 : 00000000 000007FC, t9 : 00000000 2A300200, k0 : 00000000 00000000, k1 : 00000000 00000000
    gp : 00000000 29133C00, sp : 00000000 3022FBB8, s8 : 00000000 00000054, ra : 00000000 22768424
    EPC : 22768478, ErrorEPC : 80412AB4, SREG : 500099E3
    MDLO : 87126668, MDHI : D990ADBB, BadVaddr : 00000014
    CacheErr_Icache : 0x007F7F00 - 000040D8, CacheErr_Dcache : 0x00000000 - 00001FA0
    TagLo_Icache : 0x00000000 - 23642303, DataLo_Icache : 0xAFBF0018 - 0D81ADDB
    DataHi_Icache: 0x00000000 - 00000001
    TagLo_Dcache : 0x00000000 - 2277E583, TagHi_Dcache : 0x00000000 - 0912BD81
    DataLo_Dcache: 0x00000001 - 2368110C, DataHi_Dcache : 0x00000000 - 0000001C
    TEXT_START : 0x21003178
    DATA_START : 0x260888A0
    Cause 0000040C (Code 0x3): TLB (store) exception

    22:02:11 UTC Thu Oct 28 2010: TLB (store) exception, CPU signal 10, PC = 0x22768478

    --------------------------------------------------------------------
    Possible software fault. Upon reccurence, please collect
    crashinfo, "show tech" and contact Cisco Technical Support.
    --------------------------------------------------------------------

    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z
    $0 : 00000000 00000000, AT : 00000000 29130000, v0 : 00000000 00000001, v1 : 00000000 0D8B8540
    a0 : 00000000 00000000, a1 : 00000000 0D8B8584, a2 : 00000000 2A2F8ABC, a3 : 00000000 00000004
    t0 : 00000000 00000020, t1 : 00000000 500099E1, t2 : 00000000 500081E0, t3 : FFFFFFFF FFFFFFF2
    t4 : 00000000 0000000E, t5 : 00000000 00000000, t6 : 00000000 0D95F890, t7 : 00000000 000001FF
    s0 : 00000000 00000000, s1 : 00000000 2A2FDB40, s2 : FFFFFFFF FFFFFFEC, s3 : 00000000 3080C980
    s4 : 00000000 0D95F89E, s5 : 00000000 2A300EE0, s6 : 00000000 00000000, s7 : 00000000 0000000E
    t8 : 00000000 000007FC, t9 : 00000000 2A300200, k0 : 00000000 00000000, k1 : 00000000 00000000
    gp : 00000000 29133C00, sp : 00000000 3022FBB8, s8 : 00000000 00000054, ra : 00000000 22768424
    EPC : 22768478, ErrorEPC : 80412AB4, SREG : 500099E3
    MDLO : 87126668, MDHI : D990ADBB, BadVaddr : 00000014
    CacheErr_Icache : 0x007F7F00 - 000040D8, CacheErr_Dcache : 0x00000000 - 00001FA0
    TagLo_Icache : 0x00000000 - 23642303, DataLo_Icache : 0xAFBF0018 - 0D81ADDB
    DataHi_Icache: 0x00000000 - 00000001
    TagLo_Dcache : 0x00000000 - 2277E583, TagHi_Dcache : 0x00000000 - 0912BD81
    DataLo_Dcache: 0x00000001 - 2368110C, DataHi_Dcache : 0x00000000 - 0000001C
    TEXT_START : 0x21003178
    DATA_START : 0x260888A0
    Cause 0000040C (Code 0x3): TLB (store) exception
    Writing crashinfo to flash:crashinfo_20101028-220211-UTC
    22:02:11 UTC Thu Oct 28 2010: TLB (store) exception, CPU signal 10, PC = 0x22768478

    --------------------------------------------------------------------
    Possible software fault. Upon reccurence, please collect
    crashinfo, "show tech" and contact Cisco Technical Support.
    --------------------------------------------------------------------

    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z
    $0 : 00000000 00000000, AT : 00000000 29130000, v0 : 00000000 00000001, v1 : 00000000 0D8B8540
    a0 : 00000000 00000000, a1 : 00000000 0D8B8584, a2 : 00000000 2A2F8ABC, a3 : 00000000 00000004
    t0 : 00000000 00000020, t1 : 00000000 500099E1, t2 : 00000000 500081E0, t3 : FFFFFFFF FFFFFFF2
    t4 : 00000000 0000000E, t5 : 00000000 00000000, t6 : 00000000 0D95F890, t7 : 00000000 000001FF
    s0 : 00000000 00000000, s1 : 00000000 2A2FDB40, s2 : FFFFFFFF FFFFFFEC, s3 : 00000000 3080C980
    s4 : 00000000 0D95F89E, s5 : 00000000 2A300EE0, s6 : 00000000 00000000, s7 : 00000000 0000000E
    t8 : 00000000 000007FC, t9 : 00000000 2A300200, k0 : 00000000 00000000, k1 : 00000000 00000000
    gp : 00000000 29133C00, sp : 00000000 3022FBB8, s8 : 00000000 00000054, ra : 00000000 22768424
    EPC : 22768478, ErrorEPC : 80412AB4, SREG : 500099E3
    MDLO : 87126668, MDHI : D990ADBB, BadVaddr : 00000014
    CacheErr_Icache : 0x007F7F00 - 000040D8, CacheErr_Dcache : 0x00000000 - 00001FA0
    TagLo_Icache : 0x00000000 - 23642303, DataLo_Icache : 0xAFBF0018 - 0D81ADDB
    DataHi_Icache: 0x00000000 - 00000001
    TagLo_Dcache : 0x00000000 - 2277E583, TagHi_Dcache : 0x00000000 - 0912BD81
    DataLo_Dcache: 0x00000001 - 2368110C, DataHi_Dcache : 0x00000000 - 0000001C
    TEXT_START : 0x21003178
    DATA_START : 0x260888A0
    Cause 0000040C (Code 0x3): TLB (store) exception
    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z

    === Flushing messages (22:02:12 UTC Thu Oct 28 2010) ===
    Buffered messages:
    *Oct 28 20:52:40.075: %LINK-3-UPDOWN: Interface SM1/0, changed state to up
    *Oct 28 20:52:42.195: %LINK-3-UPDOWN: Interface GigabitEthernet0/0, changed state to up
    *Oct 28 20:52:42.195: %LINK-3-UPDOWN: Interface GigabitEthernet0/1, changed state to down
    *Oct 28 20:52:42.195: %LINK-3-UPDOWN: Interface GigabitEthernet0/2, changed state to down
    *Oct 28 20:52:44.631: %LINK-3-UPDOWN: Interface SM1/1, changed state to up
    *Oct 28 20:53:01.655: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/0, changed state to up
    *Oct 28 20:53:01.923: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/1, changed state to up
    *Oct 28 20:53:02.075: %LINK-3-UPDOWN: Interface Foreign Exchange Station 0/1/0, changed state to up
    *Oct 28 20:53:02.075: %LINK-3-UPDOWN: Interface Foreign Exchange Station 0/1/1, changed state to up
    *Oct 28 20:53:43.739: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/0, changed state to operational status down due to cable removal
    *Oct 28 20:53:44.739: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/1, changed state to operational status down due to cable removal
    Queued messages:
    No warm reboot Storage
    *** System received a Bus Error exception ***
    signal= 0xa, code= 0x40c, context= 0x29726b74
    PC = 0x22768478, SP = 0x3022fbb8, RA = 0x22768424
    Cause Reg = 0x0000040c, Status Reg = 0x500099e3
    System Bootstrap, Version 15.0(1r)M6, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 2010 by cisco Systems, Inc.
    Total memory size = 512 MB - On-board = 512 MB, DIMM0 = 0 MB
    CISCO2911/K9 platform with 524288 Kbytes of main memory
    Main memory is configured to 72/-1(On-board/DIMM0) bit mode with ECC enabled

    Readonly ROMMON initialized
    program load complete, entry point: 0x80803000, size: 0x1b340

    IOS Image Load Test
    ___________________
    Digitally Signed Development Software
    program load complete, entry point: 0x81000000, size: 0x40b6b74
    Self decompressing the image : #############################################################################################################

    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2691036>
    or simply reply to this email.
    -- --
    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2691978>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2699015>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2699042>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2699089>
    or simply reply to this email.

    Subject: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-
    Replied by: Ken Romo on 20-11-2010 01:34:36 AM
    Radhika,
     
    Tried latest IOS from today same crash.
     
    How do I remover the PVDMS?
     
    Ken
     
    +++++++++++++++++++++++
     
    Ken,

    Please try out the new image sent by Brett to you when you get a chance. Also one difference we noticed is that you have PVDM¿s in your setup that we don not have in our test setup. Would it be possible to remove the PVDMS temporarily and try the ping? This may help us root cause the issue.



    I will also schedule a WebEx for tomorrow morning 10:30 PST with the IOS developer so we can take a look if the change of IOS image and removal of PVDM¿s does not solve the issue. Please let me know if that time slot does not work for you.



    Thanks,

    Radhika





    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Monday, November 01, 2010 11:19 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    Here you go:

    boxer#show vlan-switch
    VLAN Name Status Ports
    ---- -------------------------------- --------- -------------------------------
    1 default active
    1002 fddi-default act/unsup
    1003 token-ring-default act/unsup
    1004 fddinet-default act/unsup
    1005 trnet-default act/unsup
    VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2
    ---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------
    1 enet 100001 1500 - - - - - 1002 1003
    1002 fddi 101002 1500 - - - - - 1 1003
    1003 tr 101003 1500 1005 0 - - srb 1 1002
    1004 fdnet 101004 1500 - - 1 ibm - 0 0
    1005 trnet 101005 1500 - - 1 ibm - 0 0


    boxer#sh platform mgf module
    Registered Module Information
    Code: NR - Not Registered, TM - Trust Mode, SP - Scheduling Profile
    BL - Buffer Level, TR - Traffic Rate, PT - Pause Threshold
    slot vlan type/ID TM SP BL TR PT
    ---- ---- ---------- ------- --- ------ ----- ----
    ISM NR
    EHWIC-0 NR
    EHWIC-1 NR
    EHWIC-2 NR
    EHWIC-3 NR
    PVDM-0 2 PVDM/5 UP 1 low 1000 low
    PVDM-1 2 PVDM/5 UP 1 low 1000 low
    SM-1 1 Switch/3 UP 1 low 1000 high




    Thanks Ken. Can you also give us the output of the following.



    1) show vlan-switch

    2) ¿show platform mgf module¿ before the crash happens.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Monday, November 01, 2010 10:50 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    I will try whatever you suggest, just let me know when you have posted the new IOS.

    Below is my config:

    boxer#sh run
    Building configuration...

    Current configuration : 5777 bytes
    !
    version 15.1
    service timestamps debug datetime msec
    service timestamps log datetime msec
    no service password-encryption
    !
    hostname boxer
    !
    boot-start-marker
    boot system flash0 c2900-universalk9-mz.SSA.151-2.19.T
    boot-end-marker
    !
    !
    logging buffered 51200 warnings
    !
    no aaa new-model
    !
    no ipv6 cef
    ip source-route
    ip cef
    !
    !
    !
    !
    !
    ip domain name yourdomain.com
    multilink bundle-name authenticated
    !
    !
    !
    !
    !
    crypto pki token default removal timeout 0
    !
    crypto pki trustpoint TP-self-signed-1999750280
    enrollment selfsigned
    subject-name cn=IOS-Self-Signed-Certificate-1999750280
    revocation-check none
    rsakeypair TP-self-signed-1999750280
    !
    !
    crypto pki certificate chain TP-self-signed-1999750280
    certificate self-signed 01
    3082024C 308201B5 A0030201 02020101 300D0609 2A864886 F70D0101 04050030
    31312F30 2D060355 04031326 494F532D 53656C66 2D536967 6E65642D 43657274
    69666963 6174652D 31393939 37353032 3830301E 170D3130 31303230 32323335
    32365A17 0D323030 31303130 30303030 305A3031 312F302D 06035504 03132649
    4F532D53 656C662D 5369676E 65642D43 65727469 66696361 74652D31 39393937
    35303238 3030819F 300D0609 2A864886 F70D0101 01050003 818D0030 81890281
    81009378 2E139D79 DCA59865 14AB3398 870362B7 40BB9C13 A5DC5315 6108DF92
    5E78CF06 A40D4DB5 B66D410E FAFE75AC 764997B1 5C551A47 CFA00109 520352EC
    33A69E24 B3C1175B 136FC62A 8BE4637E B834059B FC7CAA6E 957DA0BB 66D8DC49
    80F82890 981FFCFE 0DC7E6F9 53287989 3887C5F6 AF59D0BE B502E11E FD16F556
    DBB90203 010001A3 74307230 0F060355 1D130101 FF040530 030101FF 301F0603
    551D1104 18301682 14626F78 65722E79 6F757264 6F6D6169 6E2E636F 6D301F06
    03551D23 04183016 80143541 7934E424 4B9A60DB E6C908C3 C20BAA17 D058301D
    0603551D 0E041604 14354179 34E4244B 9A60DBE6 C908C3C2 0BAA17D0 58300D06
    092A8648 86F70D01 01040500 03818100 3D222AB5 177D452F 153DCA26 1D7ECB49
    58BCBF60 DA18DC04 94B82EA3 76884EBC D7131641 08687C04 6C6645DF 78B2D2F8
    409BCAD7 50AF5091 B99614FD C2424D89 407A9109 BCA20473 F4CE33D4 4B126483
    C240C0B9 7A628E53 E419FEC3 B8853671 03113F5E 47FA8120 9F9A7A9D 11498FE0
    82C96578 8FD9770A EBD27F73 DF2E1487
    quit
    voice-card 0
    !
    !
    !
    !
    !
    !
    !
    license udi pid CISCO2911/K9 sn FTX1422A077
    hw-module pvdm 0/0
    !
    hw-module sm 1
    !
    !
    !
    username jack privilege 15 secret 5 $1$c5QR$fYGTbhWRKsBZ1JpNyIQGG1
    username marco privilege 15 secret 5 $1$amqq$5pI0T7mUViDL5Y.NqX/yz.
    !
    redundancy
    !
    !
    !
    !
    !
    !
    interface GigabitEthernet0/0
    description To tusqa network
    ip address 172.17.17.130 255.255.248.0
    duplex auto
    speed auto
    !
    interface GigabitEthernet0/1
    no ip address
    shutdown
    duplex auto
    speed auto
    !
    interface GigabitEthernet0/2
    no ip address
    shutdown
    duplex auto
    speed auto
    !
    interface SM1/0
    ip unnumbered GigabitEthernet0/0
    service-module ip address 172.17.17.129 255.255.248.0
    !Application: SRE-V Running on SMV
    service-module ip default-gateway 172.17.17.130
    service-module mgf ip address 10.62.64.1 255.255.255.0
    service-module mgf ip default-gateway 10.62.64.2
    !
    interface SM1/1
    description Internal switch interface connected to Service Module
    switchport mode trunk
    !
    interface Vlan1
    ip address 10.62.64.2 255.255.255.0
    !
    ip forward-protocol nd
    !
    ip http server
    ip http access-class 23
    ip http authentication local
    ip http secure-server
    ip http timeout-policy idle 60 life 86400 requests 10000
    !
    ip route 172.17.17.129 255.255.255.255 SM1/0
    !
    !
    !
    !
    control-plane
    !
    !
    voice-port 0/0/0
    !
    voice-port 0/0/1
    !
    voice-port 0/1/0
    !
    voice-port 0/1/1
    !
    !
    !
    mgcp profile default
    !
    !
    !
    !
    !
    gatekeeper
    shutdown
    !
    !
    banner exec ^C
    % Password expiration warning.
    -----------------------------------------------------------------------
    Cisco Configuration Professional (Cisco CP) is installed on this device
    and it provides the default username "cisco" for one-time use. If you have
    already used the username "cisco" to login to the router and your IOS image
    supports the "one-time" user option, then this username has already expired.
    You will not be able to login to the router with this username after you exit
    this session.
    It is strongly suggested that you create a new username with a privilege level
    of 15 using the following command.
    username <myuser> privilege 15 secret 0 <mypassword>
    Replace <myuser> and <mypassword> with the username and password you want to
    use.
    -----------------------------------------------------------------------
    ^C
    banner login ^C
    -----------------------------------------------------------------------
    Cisco Configuration Professional (Cisco CP) is installed on this device.
    This feature requires the one-time use of the username "cisco" with the
    password "cisco". These default credentials have a privilege level of 15.
    YOU MUST USE CISCO CP or the CISCO IOS CLI TO CHANGE THESE PUBLICLY-KNOWN
    CREDENTIALS
    Here are the Cisco IOS commands.
    username <myuser> privilege 15 secret 0 <mypassword>
    no username cisco
    Replace <myuser> and <mypassword> with the username and password you want
    to use.
    IF YOU DO NOT CHANGE THE PUBLICLY-KNOWN CREDENTIALS, YOU WILL NOT BE ABLE
    TO LOG INTO THE DEVICE AGAIN AFTER YOU HAVE LOGGED OFF.
    For more information about Cisco CP please follow the instructions in the
    QUICK START GUIDE for your router or go to http://www.cisco.com/go/ciscocp
    -----------------------------------------------------------------------
    ^C
    !
    line con 0
    login local
    line aux 0
    line 67
    no activation-character
    no exec
    transport preferred none
    transport input all
    transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
    stopbits 1
    flowcontrol software
    line vty 0 4
    privilege level 15
    login local
    transport input telnet
    line vty 5 15
    privilege level 15
    login local
    transport input telnet ssh
    !
    exception data-corruption buffer truncate
    scheduler allocate 20000 1000
    end



    Ken, Thanks for trying out the image for us. We are trying to reproduce this on our end but have had no luck so far. Can you please send us the output of show running-config from your router.



    Also we have one more image that we would like you to try it out before the debusg session would that be ok?



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Monday, November 01, 2010 10:22 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------

    Radhika,

    I tried the new OS and still getting same IOS crash.
    As mentioned I will work around your schedule so let me if you were able to get someone from the IOS team to help troubleshoot today.

    Thanks in advance,

    Ken Romo


    Ken,

    I am trying to get some help from the IOS team since this a router crash. So I will setup the webex session to debug for some time Monday so we can collect all the information and try out any suggestion from them.



    For Now We will post a newer IOS image to the beta Site and can you give that a try to see if that will solve the issue.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Friday, October 29, 2010 8:24 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    I will work around your schedule, anytime you are available, I will make myself available.
    email:
    kromo@opentext.com

    Thanks in advance,

    Ken Romo

    +++++++++++++++++++++++++++++++++

    Ken,

    Would a webex session tomorrow morning (any time between 10:00 and 1:00) work for you? Let me know the time that would work for you and also your email address so I can send you a webex invite.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Thursday, October 28, 2010 3:12 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Radhika Miriyala in Service Ready Engine Virtualizatio



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    No worries, we are trying to work this out together and I appreciate the help.
    s/m 1/1 is set as trunk but I went ahead and reconfigured to truank again and reloaded OS and get the same crash when I ping to the MGF interface from the SRE (I attached the errors at the bottom of this message).

    Ken,

    Sorry I just realized the mistake. I meant to say make the interface sm 1/1 as trunk.

    Sorry about the confusion.



    Please try it out.



    Thanks,

    Radhika



    boxer#
    %ALIGN-1-FATAL: Illegal access to a low address 22:02:10 UTC Thu Oct 28 2010
    addr=0x14, pc=0x22765BD8z , ra=0x22765B84z , sp=0x3022FBB8
    %ALIGN-1-FATAL: Illegal access to a low address 22:02:11 UTC Thu Oct 28 2010
    addr=0x14, pc=0x22765BD8z , ra=0x22765B84z , sp=0x3022FBB8

    22:02:11 UTC Thu Oct 28 2010: TLB (store) exception, CPU signal 10, PC = 0x22768478

    --------------------------------------------------------------------
    Possible software fault. Upon reccurence, please collect
    crashinfo, "show tech" and contact Cisco Technical Support.
    --------------------------------------------------------------------

    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z
    $0 : 00000000 00000000, AT : 00000000 29130000, v0 : 00000000 00000001, v1 : 00000000 0D8B8540
    a0 : 00000000 00000000, a1 : 00000000 0D8B8584, a2 : 00000000 2A2F8ABC, a3 : 00000000 00000004
    t0 : 00000000 00000020, t1 : 00000000 500099E1, t2 : 00000000 500081E0, t3 : FFFFFFFF FFFFFFF2
    t4 : 00000000 0000000E, t5 : 00000000 00000000, t6 : 00000000 0D95F890, t7 : 00000000 000001FF
    s0 : 00000000 00000000, s1 : 00000000 2A2FDB40, s2 : FFFFFFFF FFFFFFEC, s3 : 00000000 3080C980
    s4 : 00000000 0D95F89E, s5 : 00000000 2A300EE0, s6 : 00000000 00000000, s7 : 00000000 0000000E
    t8 : 00000000 000007FC, t9 : 00000000 2A300200, k0 : 00000000 00000000, k1 : 00000000 00000000
    gp : 00000000 29133C00, sp : 00000000 3022FBB8, s8 : 00000000 00000054, ra : 00000000 22768424
    EPC : 22768478, ErrorEPC : 80412AB4, SREG : 500099E3
    MDLO : 87126668, MDHI : D990ADBB, BadVaddr : 00000014
    CacheErr_Icache : 0x007F7F00 - 000040D8, CacheErr_Dcache : 0x00000000 - 00001FA0
    TagLo_Icache : 0x00000000 - 23642303, DataLo_Icache : 0xAFBF0018 - 0D81ADDB
    DataHi_Icache: 0x00000000 - 00000001
    TagLo_Dcache : 0x00000000 - 2277E583, TagHi_Dcache : 0x00000000 - 0912BD81
    DataLo_Dcache: 0x00000001 - 2368110C, DataHi_Dcache : 0x00000000 - 0000001C
    TEXT_START : 0x21003178
    DATA_START : 0x260888A0
    Cause 0000040C (Code 0x3): TLB (store) exception

    22:02:11 UTC Thu Oct 28 2010: TLB (store) exception, CPU signal 10, PC = 0x22768478

    --------------------------------------------------------------------
    Possible software fault. Upon reccurence, please collect
    crashinfo, "show tech" and contact Cisco Technical Support.
    --------------------------------------------------------------------

    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z
    $0 : 00000000 00000000, AT : 00000000 29130000, v0 : 00000000 00000001, v1 : 00000000 0D8B8540
    a0 : 00000000 00000000, a1 : 00000000 0D8B8584, a2 : 00000000 2A2F8ABC, a3 : 00000000 00000004
    t0 : 00000000 00000020, t1 : 00000000 500099E1, t2 : 00000000 500081E0, t3 : FFFFFFFF FFFFFFF2
    t4 : 00000000 0000000E, t5 : 00000000 00000000, t6 : 00000000 0D95F890, t7 : 00000000 000001FF
    s0 : 00000000 00000000, s1 : 00000000 2A2FDB40, s2 : FFFFFFFF FFFFFFEC, s3 : 00000000 3080C980
    s4 : 00000000 0D95F89E, s5 : 00000000 2A300EE0, s6 : 00000000 00000000, s7 : 00000000 0000000E
    t8 : 00000000 000007FC, t9 : 00000000 2A300200, k0 : 00000000 00000000, k1 : 00000000 00000000
    gp : 00000000 29133C00, sp : 00000000 3022FBB8, s8 : 00000000 00000054, ra : 00000000 22768424
    EPC : 22768478, ErrorEPC : 80412AB4, SREG : 500099E3
    MDLO : 87126668, MDHI : D990ADBB, BadVaddr : 00000014
    CacheErr_Icache : 0x007F7F00 - 000040D8, CacheErr_Dcache : 0x00000000 - 00001FA0
    TagLo_Icache : 0x00000000 - 23642303, DataLo_Icache : 0xAFBF0018 - 0D81ADDB
    DataHi_Icache: 0x00000000 - 00000001
    TagLo_Dcache : 0x00000000 - 2277E583, TagHi_Dcache : 0x00000000 - 0912BD81
    DataLo_Dcache: 0x00000001 - 2368110C, DataHi_Dcache : 0x00000000 - 0000001C
    TEXT_START : 0x21003178
    DATA_START : 0x260888A0
    Cause 0000040C (Code 0x3): TLB (store) exception
    Writing crashinfo to flash:crashinfo_20101028-220211-UTC
    22:02:11 UTC Thu Oct 28 2010: TLB (store) exception, CPU signal 10, PC = 0x22768478

    --------------------------------------------------------------------
    Possible software fault. Upon reccurence, please collect
    crashinfo, "show tech" and contact Cisco Technical Support.
    --------------------------------------------------------------------

    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z
    $0 : 00000000 00000000, AT : 00000000 29130000, v0 : 00000000 00000001, v1 : 00000000 0D8B8540
    a0 : 00000000 00000000, a1 : 00000000 0D8B8584, a2 : 00000000 2A2F8ABC, a3 : 00000000 00000004
    t0 : 00000000 00000020, t1 : 00000000 500099E1, t2 : 00000000 500081E0, t3 : FFFFFFFF FFFFFFF2
    t4 : 00000000 0000000E, t5 : 00000000 00000000, t6 : 00000000 0D95F890, t7 : 00000000 000001FF
    s0 : 00000000 00000000, s1 : 00000000 2A2FDB40, s2 : FFFFFFFF FFFFFFEC, s3 : 00000000 3080C980
    s4 : 00000000 0D95F89E, s5 : 00000000 2A300EE0, s6 : 00000000 00000000, s7 : 00000000 0000000E
    t8 : 00000000 000007FC, t9 : 00000000 2A300200, k0 : 00000000 00000000, k1 : 00000000 00000000
    gp : 00000000 29133C00, sp : 00000000 3022FBB8, s8 : 00000000 00000054, ra : 00000000 22768424
    EPC : 22768478, ErrorEPC : 80412AB4, SREG : 500099E3
    MDLO : 87126668, MDHI : D990ADBB, BadVaddr : 00000014
    CacheErr_Icache : 0x007F7F00 - 000040D8, CacheErr_Dcache : 0x00000000 - 00001FA0
    TagLo_Icache : 0x00000000 - 23642303, DataLo_Icache : 0xAFBF0018 - 0D81ADDB
    DataHi_Icache: 0x00000000 - 00000001
    TagLo_Dcache : 0x00000000 - 2277E583, TagHi_Dcache : 0x00000000 - 0912BD81
    DataLo_Dcache: 0x00000001 - 2368110C, DataHi_Dcache : 0x00000000 - 0000001C
    TEXT_START : 0x21003178
    DATA_START : 0x260888A0
    Cause 0000040C (Code 0x3): TLB (store) exception
    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z

    === Flushing messages (22:02:12 UTC Thu Oct 28 2010) ===
    Buffered messages:
    *Oct 28 20:52:40.075: %LINK-3-UPDOWN: Interface SM1/0, changed state to up
    *Oct 28 20:52:42.195: %LINK-3-UPDOWN: Interface GigabitEthernet0/0, changed state to up
    *Oct 28 20:52:42.195: %LINK-3-UPDOWN: Interface GigabitEthernet0/1, changed state to down
    *Oct 28 20:52:42.195: %LINK-3-UPDOWN: Interface GigabitEthernet0/2, changed state to down
    *Oct 28 20:52:44.631: %LINK-3-UPDOWN: Interface SM1/1, changed state to up
    *Oct 28 20:53:01.655: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/0, changed state to up
    *Oct 28 20:53:01.923: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/1, changed state to up
    *Oct 28 20:53:02.075: %LINK-3-UPDOWN: Interface Foreign Exchange Station 0/1/0, changed state to up
    *Oct 28 20:53:02.075: %LINK-3-UPDOWN: Interface Foreign Exchange Station 0/1/1, changed state to up
    *Oct 28 20:53:43.739: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/0, changed state to operational status down due to cable removal
    *Oct 28 20:53:44.739: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/1, changed state to operational status down due to cable removal
    Queued messages:
    No warm reboot Storage
    *** System received a Bus Error exception ***
    signal= 0xa, code= 0x40c, context= 0x29726b74
    PC = 0x22768478, SP = 0x3022fbb8, RA = 0x22768424
    Cause Reg = 0x0000040c, Status Reg = 0x500099e3
    System Bootstrap, Version 15.0(1r)M6, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 2010 by cisco Systems, Inc.
    Total memory size = 512 MB - On-board = 512 MB, DIMM0 = 0 MB
    CISCO2911/K9 platform with 524288 Kbytes of main memory
    Main memory is configured to 72/-1(On-board/DIMM0) bit mode with ECC enabled

    Readonly ROMMON initialized
    program load complete, entry point: 0x80803000, size: 0x1b340

    IOS Image Load Test
    ___________________
    Digitally Signed Development Software
    program load complete, entry point: 0x81000000, size: 0x40b6b74
    Self decompressing the image : #############################################################################################################

    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2691036>
    or simply reply to this email.
    -- --
    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2691978>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2699015>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2699042>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2699089>
    or simply reply to this email.


    Subject: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-
    Replied by: Ken Romo on 20-11-2010 01:34:36 AM
    Radhika,
     
    I pulled the PVDM and it is working.
     
    Does this mean the PVDM is bad?
     
    Ken
     
    Ken,

    Please try out the new image sent by Brett to you when you get a chance. Also one difference we noticed is that you have PVDM¿s in your setup that we don not have in our test setup. Would it be possible to remove the PVDMS temporarily and try the ping? This may help us root cause the issue.



    I will also schedule a WebEx for tomorrow morning 10:30 PST with the IOS developer so we can take a look if the change of IOS image and removal of PVDM¿s does not solve the issue. Please let me know if that time slot does not work for you.



    Thanks,

    Radhika





    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Monday, November 01, 2010 11:19 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    Here you go:

    boxer#show vlan-switch
    VLAN Name Status Ports
    ---- -------------------------------- --------- -------------------------------
    1 default active
    1002 fddi-default act/unsup
    1003 token-ring-default act/unsup
    1004 fddinet-default act/unsup
    1005 trnet-default act/unsup
    VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2
    ---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------
    1 enet 100001 1500 - - - - - 1002 1003
    1002 fddi 101002 1500 - - - - - 1 1003
    1003 tr 101003 1500 1005 0 - - srb 1 1002
    1004 fdnet 101004 1500 - - 1 ibm - 0 0
    1005 trnet 101005 1500 - - 1 ibm - 0 0


    boxer#sh platform mgf module
    Registered Module Information
    Code: NR - Not Registered, TM - Trust Mode, SP - Scheduling Profile
    BL - Buffer Level, TR - Traffic Rate, PT - Pause Threshold
    slot vlan type/ID TM SP BL TR PT
    ---- ---- ---------- ------- --- ------ ----- ----
    ISM NR
    EHWIC-0 NR
    EHWIC-1 NR
    EHWIC-2 NR
    EHWIC-3 NR
    PVDM-0 2 PVDM/5 UP 1 low 1000 low
    PVDM-1 2 PVDM/5 UP 1 low 1000 low
    SM-1 1 Switch/3 UP 1 low 1000 high




    Thanks Ken. Can you also give us the output of the following.



    1) show vlan-switch

    2) ¿show platform mgf module¿ before the crash happens.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Monday, November 01, 2010 10:50 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    I will try whatever you suggest, just let me know when you have posted the new IOS.

    Below is my config:

    boxer#sh run
    Building configuration...

    Current configuration : 5777 bytes
    !
    version 15.1
    service timestamps debug datetime msec
    service timestamps log datetime msec
    no service password-encryption
    !
    hostname boxer
    !
    boot-start-marker
    boot system flash0 c2900-universalk9-mz.SSA.151-2.19.T
    boot-end-marker
    !
    !
    logging buffered 51200 warnings
    !
    no aaa new-model
    !
    no ipv6 cef
    ip source-route
    ip cef
    !
    !
    !
    !
    !
    ip domain name yourdomain.com
    multilink bundle-name authenticated
    !
    !
    !
    !
    !
    crypto pki token default removal timeout 0
    !
    crypto pki trustpoint TP-self-signed-1999750280
    enrollment selfsigned
    subject-name cn=IOS-Self-Signed-Certificate-1999750280
    revocation-check none
    rsakeypair TP-self-signed-1999750280
    !
    !
    crypto pki certificate chain TP-self-signed-1999750280
    certificate self-signed 01
    3082024C 308201B5 A0030201 02020101 300D0609 2A864886 F70D0101 04050030
    31312F30 2D060355 04031326 494F532D 53656C66 2D536967 6E65642D 43657274
    69666963 6174652D 31393939 37353032 3830301E 170D3130 31303230 32323335
    32365A17 0D323030 31303130 30303030 305A3031 312F302D 06035504 03132649
    4F532D53 656C662D 5369676E 65642D43 65727469 66696361 74652D31 39393937
    35303238 3030819F 300D0609 2A864886 F70D0101 01050003 818D0030 81890281
    81009378 2E139D79 DCA59865 14AB3398 870362B7 40BB9C13 A5DC5315 6108DF92
    5E78CF06 A40D4DB5 B66D410E FAFE75AC 764997B1 5C551A47 CFA00109 520352EC
    33A69E24 B3C1175B 136FC62A 8BE4637E B834059B FC7CAA6E 957DA0BB 66D8DC49
    80F82890 981FFCFE 0DC7E6F9 53287989 3887C5F6 AF59D0BE B502E11E FD16F556
    DBB90203 010001A3 74307230 0F060355 1D130101 FF040530 030101FF 301F0603
    551D1104 18301682 14626F78 65722E79 6F757264 6F6D6169 6E2E636F 6D301F06
    03551D23 04183016 80143541 7934E424 4B9A60DB E6C908C3 C20BAA17 D058301D
    0603551D 0E041604 14354179 34E4244B 9A60DBE6 C908C3C2 0BAA17D0 58300D06
    092A8648 86F70D01 01040500 03818100 3D222AB5 177D452F 153DCA26 1D7ECB49
    58BCBF60 DA18DC04 94B82EA3 76884EBC D7131641 08687C04 6C6645DF 78B2D2F8
    409BCAD7 50AF5091 B99614FD C2424D89 407A9109 BCA20473 F4CE33D4 4B126483
    C240C0B9 7A628E53 E419FEC3 B8853671 03113F5E 47FA8120 9F9A7A9D 11498FE0
    82C96578 8FD9770A EBD27F73 DF2E1487
    quit
    voice-card 0
    !
    !
    !
    !
    !
    !
    !
    license udi pid CISCO2911/K9 sn FTX1422A077
    hw-module pvdm 0/0
    !
    hw-module sm 1
    !
    !
    !
    username jack privilege 15 secret 5 $1$c5QR$fYGTbhWRKsBZ1JpNyIQGG1
    username marco privilege 15 secret 5 $1$amqq$5pI0T7mUViDL5Y.NqX/yz.
    !
    redundancy
    !
    !
    !
    !
    !
    !
    interface GigabitEthernet0/0
    description To tusqa network
    ip address 172.17.17.130 255.255.248.0
    duplex auto
    speed auto
    !
    interface GigabitEthernet0/1
    no ip address
    shutdown
    duplex auto
    speed auto
    !
    interface GigabitEthernet0/2
    no ip address
    shutdown
    duplex auto
    speed auto
    !
    interface SM1/0
    ip unnumbered GigabitEthernet0/0
    service-module ip address 172.17.17.129 255.255.248.0
    !Application: SRE-V Running on SMV
    service-module ip default-gateway 172.17.17.130
    service-module mgf ip address 10.62.64.1 255.255.255.0
    service-module mgf ip default-gateway 10.62.64.2
    !
    interface SM1/1
    description Internal switch interface connected to Service Module
    switchport mode trunk
    !
    interface Vlan1
    ip address 10.62.64.2 255.255.255.0
    !
    ip forward-protocol nd
    !
    ip http server
    ip http access-class 23
    ip http authentication local
    ip http secure-server
    ip http timeout-policy idle 60 life 86400 requests 10000
    !
    ip route 172.17.17.129 255.255.255.255 SM1/0
    !
    !
    !
    !
    control-plane
    !
    !
    voice-port 0/0/0
    !
    voice-port 0/0/1
    !
    voice-port 0/1/0
    !
    voice-port 0/1/1
    !
    !
    !
    mgcp profile default
    !
    !
    !
    !
    !
    gatekeeper
    shutdown
    !
    !
    banner exec ^C
    % Password expiration warning.
    -----------------------------------------------------------------------
    Cisco Configuration Professional (Cisco CP) is installed on this device
    and it provides the default username "cisco" for one-time use. If you have
    already used the username "cisco" to login to the router and your IOS image
    supports the "one-time" user option, then this username has already expired.
    You will not be able to login to the router with this username after you exit
    this session.
    It is strongly suggested that you create a new username with a privilege level
    of 15 using the following command.
    username <myuser> privilege 15 secret 0 <mypassword>
    Replace <myuser> and <mypassword> with the username and password you want to
    use.
    -----------------------------------------------------------------------
    ^C
    banner login ^C
    -----------------------------------------------------------------------
    Cisco Configuration Professional (Cisco CP) is installed on this device.
    This feature requires the one-time use of the username "cisco" with the
    password "cisco". These default credentials have a privilege level of 15.
    YOU MUST USE CISCO CP or the CISCO IOS CLI TO CHANGE THESE PUBLICLY-KNOWN
    CREDENTIALS
    Here are the Cisco IOS commands.
    username <myuser> privilege 15 secret 0 <mypassword>
    no username cisco
    Replace <myuser> and <mypassword> with the username and password you want
    to use.
    IF YOU DO NOT CHANGE THE PUBLICLY-KNOWN CREDENTIALS, YOU WILL NOT BE ABLE
    TO LOG INTO THE DEVICE AGAIN AFTER YOU HAVE LOGGED OFF.
    For more information about Cisco CP please follow the instructions in the
    QUICK START GUIDE for your router or go to http://www.cisco.com/go/ciscocp
    -----------------------------------------------------------------------
    ^C
    !
    line con 0
    login local
    line aux 0
    line 67
    no activation-character
    no exec
    transport preferred none
    transport input all
    transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
    stopbits 1
    flowcontrol software
    line vty 0 4
    privilege level 15
    login local
    transport input telnet
    line vty 5 15
    privilege level 15
    login local
    transport input telnet ssh
    !
    exception data-corruption buffer truncate
    scheduler allocate 20000 1000
    end



    Ken, Thanks for trying out the image for us. We are trying to reproduce this on our end but have had no luck so far. Can you please send us the output of show running-config from your router.



    Also we have one more image that we would like you to try it out before the debusg session would that be ok?



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Monday, November 01, 2010 10:22 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------

    Radhika,

    I tried the new OS and still getting same IOS crash.
    As mentioned I will work around your schedule so let me if you were able to get someone from the IOS team to help troubleshoot today.

    Thanks in advance,

    Ken Romo


    Ken,

    I am trying to get some help from the IOS team since this a router crash. So I will setup the webex session to debug for some time Monday so we can collect all the information and try out any suggestion from them.



    For Now We will post a newer IOS image to the beta Site and can you give that a try to see if that will solve the issue.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Friday, October 29, 2010 8:24 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    I will work around your schedule, anytime you are available, I will make myself available.
    email:
    kromo@opentext.com

    Thanks in advance,

    Ken Romo

    +++++++++++++++++++++++++++++++++

    Ken,

    Would a webex session tomorrow morning (any time between 10:00 and 1:00) work for you? Let me know the time that would work for you and also your email address so I can send you a webex invite.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Thursday, October 28, 2010 3:12 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Radhika Miriyala in Service Ready Engine Virtualizatio



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    No worries, we are trying to work this out together and I appreciate the help.
    s/m 1/1 is set as trunk but I went ahead and reconfigured to truank again and reloaded OS and get the same crash when I ping to the MGF interface from the SRE (I attached the errors at the bottom of this message).

    Ken,

    Sorry I just realized the mistake. I meant to say make the interface sm 1/1 as trunk.

    Sorry about the confusion.



    Please try it out.



    Thanks,

    Radhika



    boxer#
    %ALIGN-1-FATAL: Illegal access to a low address 22:02:10 UTC Thu Oct 28 2010
    addr=0x14, pc=0x22765BD8z , ra=0x22765B84z , sp=0x3022FBB8
    %ALIGN-1-FATAL: Illegal access to a low address 22:02:11 UTC Thu Oct 28 2010
    addr=0x14, pc=0x22765BD8z , ra=0x22765B84z , sp=0x3022FBB8

    22:02:11 UTC Thu Oct 28 2010: TLB (store) exception, CPU signal 10, PC = 0x22768478

    --------------------------------------------------------------------
    Possible software fault. Upon reccurence, please collect
    crashinfo, "show tech" and contact Cisco Technical Support.
    --------------------------------------------------------------------

    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z
    $0 : 00000000 00000000, AT : 00000000 29130000, v0 : 00000000 00000001, v1 : 00000000 0D8B8540
    a0 : 00000000 00000000, a1 : 00000000 0D8B8584, a2 : 00000000 2A2F8ABC, a3 : 00000000 00000004
    t0 : 00000000 00000020, t1 : 00000000 500099E1, t2 : 00000000 500081E0, t3 : FFFFFFFF FFFFFFF2
    t4 : 00000000 0000000E, t5 : 00000000 00000000, t6 : 00000000 0D95F890, t7 : 00000000 000001FF
    s0 : 00000000 00000000, s1 : 00000000 2A2FDB40, s2 : FFFFFFFF FFFFFFEC, s3 : 00000000 3080C980
    s4 : 00000000 0D95F89E, s5 : 00000000 2A300EE0, s6 : 00000000 00000000, s7 : 00000000 0000000E
    t8 : 00000000 000007FC, t9 : 00000000 2A300200, k0 : 00000000 00000000, k1 : 00000000 00000000
    gp : 00000000 29133C00, sp : 00000000 3022FBB8, s8 : 00000000 00000054, ra : 00000000 22768424
    EPC : 22768478, ErrorEPC : 80412AB4, SREG : 500099E3
    MDLO : 87126668, MDHI : D990ADBB, BadVaddr : 00000014
    CacheErr_Icache : 0x007F7F00 - 000040D8, CacheErr_Dcache : 0x00000000 - 00001FA0
    TagLo_Icache : 0x00000000 - 23642303, DataLo_Icache : 0xAFBF0018 - 0D81ADDB
    DataHi_Icache: 0x00000000 - 00000001
    TagLo_Dcache : 0x00000000 - 2277E583, TagHi_Dcache : 0x00000000 - 0912BD81
    DataLo_Dcache: 0x00000001 - 2368110C, DataHi_Dcache : 0x00000000 - 0000001C
    TEXT_START : 0x21003178
    DATA_START : 0x260888A0
    Cause 0000040C (Code 0x3): TLB (store) exception

    22:02:11 UTC Thu Oct 28 2010: TLB (store) exception, CPU signal 10, PC = 0x22768478

    --------------------------------------------------------------------
    Possible software fault. Upon reccurence, please collect
    crashinfo, "show tech" and contact Cisco Technical Support.
    --------------------------------------------------------------------

    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z
    $0 : 00000000 00000000, AT : 00000000 29130000, v0 : 00000000 00000001, v1 : 00000000 0D8B8540
    a0 : 00000000 00000000, a1 : 00000000 0D8B8584, a2 : 00000000 2A2F8ABC, a3 : 00000000 00000004
    t0 : 00000000 00000020, t1 : 00000000 500099E1, t2 : 00000000 500081E0, t3 : FFFFFFFF FFFFFFF2
    t4 : 00000000 0000000E, t5 : 00000000 00000000, t6 : 00000000 0D95F890, t7 : 00000000 000001FF
    s0 : 00000000 00000000, s1 : 00000000 2A2FDB40, s2 : FFFFFFFF FFFFFFEC, s3 : 00000000 3080C980
    s4 : 00000000 0D95F89E, s5 : 00000000 2A300EE0, s6 : 00000000 00000000, s7 : 00000000 0000000E
    t8 : 00000000 000007FC, t9 : 00000000 2A300200, k0 : 00000000 00000000, k1 : 00000000 00000000
    gp : 00000000 29133C00, sp : 00000000 3022FBB8, s8 : 00000000 00000054, ra : 00000000 22768424
    EPC : 22768478, ErrorEPC : 80412AB4, SREG : 500099E3
    MDLO : 87126668, MDHI : D990ADBB, BadVaddr : 00000014
    CacheErr_Icache : 0x007F7F00 - 000040D8, CacheErr_Dcache : 0x00000000 - 00001FA0
    TagLo_Icache : 0x00000000 - 23642303, DataLo_Icache : 0xAFBF0018 - 0D81ADDB
    DataHi_Icache: 0x00000000 - 00000001
    TagLo_Dcache : 0x00000000 - 2277E583, TagHi_Dcache : 0x00000000 - 0912BD81
    DataLo_Dcache: 0x00000001 - 2368110C, DataHi_Dcache : 0x00000000 - 0000001C
    TEXT_START : 0x21003178
    DATA_START : 0x260888A0
    Cause 0000040C (Code 0x3): TLB (store) exception
    Writing crashinfo to flash:crashinfo_20101028-220211-UTC
    22:02:11 UTC Thu Oct 28 2010: TLB (store) exception, CPU signal 10, PC = 0x22768478

    --------------------------------------------------------------------
    Possible software fault. Upon reccurence, please collect
    crashinfo, "show tech" and contact Cisco Technical Support.
    --------------------------------------------------------------------

    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z
    $0 : 00000000 00000000, AT : 00000000 29130000, v0 : 00000000 00000001, v1 : 00000000 0D8B8540
    a0 : 00000000 00000000, a1 : 00000000 0D8B8584, a2 : 00000000 2A2F8ABC, a3 : 00000000 00000004
    t0 : 00000000 00000020, t1 : 00000000 500099E1, t2 : 00000000 500081E0, t3 : FFFFFFFF FFFFFFF2
    t4 : 00000000 0000000E, t5 : 00000000 00000000, t6 : 00000000 0D95F890, t7 : 00000000 000001FF
    s0 : 00000000 00000000, s1 : 00000000 2A2FDB40, s2 : FFFFFFFF FFFFFFEC, s3 : 00000000 3080C980
    s4 : 00000000 0D95F89E, s5 : 00000000 2A300EE0, s6 : 00000000 00000000, s7 : 00000000 0000000E
    t8 : 00000000 000007FC, t9 : 00000000 2A300200, k0 : 00000000 00000000, k1 : 00000000 00000000
    gp : 00000000 29133C00, sp : 00000000 3022FBB8, s8 : 00000000 00000054, ra : 00000000 22768424
    EPC : 22768478, ErrorEPC : 80412AB4, SREG : 500099E3
    MDLO : 87126668, MDHI : D990ADBB, BadVaddr : 00000014
    CacheErr_Icache : 0x007F7F00 - 000040D8, CacheErr_Dcache : 0x00000000 - 00001FA0
    TagLo_Icache : 0x00000000 - 23642303, DataLo_Icache : 0xAFBF0018 - 0D81ADDB
    DataHi_Icache: 0x00000000 - 00000001
    TagLo_Dcache : 0x00000000 - 2277E583, TagHi_Dcache : 0x00000000 - 0912BD81
    DataLo_Dcache: 0x00000001 - 2368110C, DataHi_Dcache : 0x00000000 - 0000001C
    TEXT_START : 0x21003178
    DATA_START : 0x260888A0
    Cause 0000040C (Code 0x3): TLB (store) exception
    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z

    === Flushing messages (22:02:12 UTC Thu Oct 28 2010) ===
    Buffered messages:
    *Oct 28 20:52:40.075: %LINK-3-UPDOWN: Interface SM1/0, changed state to up
    *Oct 28 20:52:42.195: %LINK-3-UPDOWN: Interface GigabitEthernet0/0, changed state to up
    *Oct 28 20:52:42.195: %LINK-3-UPDOWN: Interface GigabitEthernet0/1, changed state to down
    *Oct 28 20:52:42.195: %LINK-3-UPDOWN: Interface GigabitEthernet0/2, changed state to down
    *Oct 28 20:52:44.631: %LINK-3-UPDOWN: Interface SM1/1, changed state to up
    *Oct 28 20:53:01.655: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/0, changed state to up
    *Oct 28 20:53:01.923: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/1, changed state to up
    *Oct 28 20:53:02.075: %LINK-3-UPDOWN: Interface Foreign Exchange Station 0/1/0, changed state to up
    *Oct 28 20:53:02.075: %LINK-3-UPDOWN: Interface Foreign Exchange Station 0/1/1, changed state to up
    *Oct 28 20:53:43.739: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/0, changed state to operational status down due to cable removal
    *Oct 28 20:53:44.739: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/1, changed state to operational status down due to cable removal
    Queued messages:
    No warm reboot Storage
    *** System received a Bus Error exception ***
    signal= 0xa, code= 0x40c, context= 0x29726b74
    PC = 0x22768478, SP = 0x3022fbb8, RA = 0x22768424
    Cause Reg = 0x0000040c, Status Reg = 0x500099e3
    System Bootstrap, Version 15.0(1r)M6, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 2010 by cisco Systems, Inc.
    Total memory size = 512 MB - On-board = 512 MB, DIMM0 = 0 MB
    CISCO2911/K9 platform with 524288 Kbytes of main memory
    Main memory is configured to 72/-1(On-board/DIMM0) bit mode with ECC enabled

    Readonly ROMMON initialized
    program load complete, entry point: 0x80803000, size: 0x1b340

    IOS Image Load Test
    ___________________
    Digitally Signed Development Software
    program load complete, entry point: 0x81000000, size: 0x40b6b74
    Self decompressing the image : #############################################################################################################

    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2691036>
    or simply reply to this email.
    -- --
    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2691978>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2699015>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2699042>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2699089>
    or simply reply to this email.


    Subject: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-
    Replied by: Radhika Miriyala on 20-11-2010 01:34:36 AM
    Ken,

    I am not sure if it is the PVDM that is bad but it could be a bug in the IOS image also where you have pvdm and the SRE module it could be some issue. For now can you continute to do beta for SRE-v without the PVDMS.



    I will check with the team and get back to you as to how to proceed.



    Can you let me know what PVDM models you have so we can try to reproduce this in our lab.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Monday, November 01, 2010 3:59 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    I pulled the PVDM and it is working.

    Does this mean the PVDM is bad?

    Ken


    Ken,

    Please try out the new image sent by Brett to you when you get a chance. Also one difference we noticed is that you have PVDM¿s in your setup that we don not have in our test setup. Would it be possible to remove the PVDMS temporarily and try the ping? This may help us root cause the issue.



    I will also schedule a WebEx for tomorrow morning 10:30 PST with the IOS developer so we can take a look if the change of IOS image and removal of PVDM¿s does not solve the issue. Please let me know if that time slot does not work for you.



    Thanks,

    Radhika





    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Monday, November 01, 2010 11:19 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    Here you go:

    boxer#show vlan-switch
    VLAN Name Status Ports
    ---- -------------------------------- --------- -------------------------------
    1 default active
    1002 fddi-default act/unsup
    1003 token-ring-default act/unsup
    1004 fddinet-default act/unsup
    1005 trnet-default act/unsup
    VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2
    ---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------
    1 enet 100001 1500 - - - - - 1002 1003
    1002 fddi 101002 1500 - - - - - 1 1003
    1003 tr 101003 1500 1005 0 - - srb 1 1002
    1004 fdnet 101004 1500 - - 1 ibm - 0 0
    1005 trnet 101005 1500 - - 1 ibm - 0 0


    boxer#sh platform mgf module
    Registered Module Information
    Code: NR - Not Registered, TM - Trust Mode, SP - Scheduling Profile
    BL - Buffer Level, TR - Traffic Rate, PT - Pause Threshold
    slot vlan type/ID TM SP BL TR PT
    ---- ---- ---------- ------- --- ------ ----- ----
    ISM NR
    EHWIC-0 NR
    EHWIC-1 NR
    EHWIC-2 NR
    EHWIC-3 NR
    PVDM-0 2 PVDM/5 UP 1 low 1000 low
    PVDM-1 2 PVDM/5 UP 1 low 1000 low
    SM-1 1 Switch/3 UP 1 low 1000 high




    Thanks Ken. Can you also give us the output of the following.



    1) show vlan-switch

    2) ¿show platform mgf module¿ before the crash happens.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Monday, November 01, 2010 10:50 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    I will try whatever you suggest, just let me know when you have posted the new IOS.

    Below is my config:

    boxer#sh run
    Building configuration...

    Current configuration : 5777 bytes
    !
    version 15.1
    service timestamps debug datetime msec
    service timestamps log datetime msec
    no service password-encryption
    !
    hostname boxer
    !
    boot-start-marker
    boot system flash0 c2900-universalk9-mz.SSA.151-2.19.T
    boot-end-marker
    !
    !
    logging buffered 51200 warnings
    !
    no aaa new-model
    !
    no ipv6 cef
    ip source-route
    ip cef
    !
    !
    !
    !
    !
    ip domain name yourdomain.com
    multilink bundle-name authenticated
    !
    !
    !
    !
    !
    crypto pki token default removal timeout 0
    !
    crypto pki trustpoint TP-self-signed-1999750280
    enrollment selfsigned
    subject-name cn=IOS-Self-Signed-Certificate-1999750280
    revocation-check none
    rsakeypair TP-self-signed-1999750280
    !
    !
    crypto pki certificate chain TP-self-signed-1999750280
    certificate self-signed 01
    3082024C 308201B5 A0030201 02020101 300D0609 2A864886 F70D0101 04050030
    31312F30 2D060355 04031326 494F532D 53656C66 2D536967 6E65642D 43657274
    69666963 6174652D 31393939 37353032 3830301E 170D3130 31303230 32323335
    32365A17 0D323030 31303130 30303030 305A3031 312F302D 06035504 03132649
    4F532D53 656C662D 5369676E 65642D43 65727469 66696361 74652D31 39393937
    35303238 3030819F 300D0609 2A864886 F70D0101 01050003 818D0030 81890281
    81009378 2E139D79 DCA59865 14AB3398 870362B7 40BB9C13 A5DC5315 6108DF92
    5E78CF06 A40D4DB5 B66D410E FAFE75AC 764997B1 5C551A47 CFA00109 520352EC
    33A69E24 B3C1175B 136FC62A 8BE4637E B834059B FC7CAA6E 957DA0BB 66D8DC49
    80F82890 981FFCFE 0DC7E6F9 53287989 3887C5F6 AF59D0BE B502E11E FD16F556
    DBB90203 010001A3 74307230 0F060355 1D130101 FF040530 030101FF 301F0603
    551D1104 18301682 14626F78 65722E79 6F757264 6F6D6169 6E2E636F 6D301F06
    03551D23 04183016 80143541 7934E424 4B9A60DB E6C908C3 C20BAA17 D058301D
    0603551D 0E041604 14354179 34E4244B 9A60DBE6 C908C3C2 0BAA17D0 58300D06
    092A8648 86F70D01 01040500 03818100 3D222AB5 177D452F 153DCA26 1D7ECB49
    58BCBF60 DA18DC04 94B82EA3 76884EBC D7131641 08687C04 6C6645DF 78B2D2F8
    409BCAD7 50AF5091 B99614FD C2424D89 407A9109 BCA20473 F4CE33D4 4B126483
    C240C0B9 7A628E53 E419FEC3 B8853671 03113F5E 47FA8120 9F9A7A9D 11498FE0
    82C96578 8FD9770A EBD27F73 DF2E1487
    quit
    voice-card 0
    !
    !
    !
    !
    !
    !
    !
    license udi pid CISCO2911/K9 sn FTX1422A077
    hw-module pvdm 0/0
    !
    hw-module sm 1
    !
    !
    !
    username jack privilege 15 secret 5 $1$c5QR$fYGTbhWRKsBZ1JpNyIQGG1
    username marco privilege 15 secret 5 $1$amqq$5pI0T7mUViDL5Y.NqX/yz.
    !
    redundancy
    !
    !
    !
    !
    !
    !
    interface GigabitEthernet0/0
    description To tusqa network
    ip address 172.17.17.130 255.255.248.0
    duplex auto
    speed auto
    !
    interface GigabitEthernet0/1
    no ip address
    shutdown
    duplex auto
    speed auto
    !
    interface GigabitEthernet0/2
    no ip address
    shutdown
    duplex auto
    speed auto
    !
    interface SM1/0
    ip unnumbered GigabitEthernet0/0
    service-module ip address 172.17.17.129 255.255.248.0
    !Application: SRE-V Running on SMV
    service-module ip default-gateway 172.17.17.130
    service-module mgf ip address 10.62.64.1 255.255.255.0
    service-module mgf ip default-gateway 10.62.64.2
    !
    interface SM1/1
    description Internal switch interface connected to Service Module
    switchport mode trunk
    !
    interface Vlan1
    ip address 10.62.64.2 255.255.255.0
    !
    ip forward-protocol nd
    !
    ip http server
    ip http access-class 23
    ip http authentication local
    ip http secure-server
    ip http timeout-policy idle 60 life 86400 requests 10000
    !
    ip route 172.17.17.129 255.255.255.255 SM1/0
    !
    !
    !
    !
    control-plane
    !
    !
    voice-port 0/0/0
    !
    voice-port 0/0/1
    !
    voice-port 0/1/0
    !
    voice-port 0/1/1
    !
    !
    !
    mgcp profile default
    !
    !
    !
    !
    !
    gatekeeper
    shutdown
    !
    !
    banner exec ^C
    % Password expiration warning.
    -----------------------------------------------------------------------
    Cisco Configuration Professional (Cisco CP) is installed on this device
    and it provides the default username "cisco" for one-time use. If you have
    already used the username "cisco" to login to the router and your IOS image
    supports the "one-time" user option, then this username has already expired.
    You will not be able to login to the router with this username after you exit
    this session.
    It is strongly suggested that you create a new username with a privilege level
    of 15 using the following command.
    username <myuser> privilege 15 secret 0 <mypassword>
    Replace <myuser> and <mypassword> with the username and password you want to
    use.
    -----------------------------------------------------------------------
    ^C
    banner login ^C
    -----------------------------------------------------------------------
    Cisco Configuration Professional (Cisco CP) is installed on this device.
    This feature requires the one-time use of the username "cisco" with the
    password "cisco". These default credentials have a privilege level of 15.
    YOU MUST USE CISCO CP or the CISCO IOS CLI TO CHANGE THESE PUBLICLY-KNOWN
    CREDENTIALS
    Here are the Cisco IOS commands.
    username <myuser> privilege 15 secret 0 <mypassword>
    no username cisco
    Replace <myuser> and <mypassword> with the username and password you want
    to use.
    IF YOU DO NOT CHANGE THE PUBLICLY-KNOWN CREDENTIALS, YOU WILL NOT BE ABLE
    TO LOG INTO THE DEVICE AGAIN AFTER YOU HAVE LOGGED OFF.
    For more information about Cisco CP please follow the instructions in the
    QUICK START GUIDE for your router or go to http://www.cisco.com/go/ciscocp
    -----------------------------------------------------------------------
    ^C
    !
    line con 0
    login local
    line aux 0
    line 67
    no activation-character
    no exec
    transport preferred none
    transport input all
    transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
    stopbits 1
    flowcontrol software
    line vty 0 4
    privilege level 15
    login local
    transport input telnet
    line vty 5 15
    privilege level 15
    login local
    transport input telnet ssh
    !
    exception data-corruption buffer truncate
    scheduler allocate 20000 1000
    end



    Ken, Thanks for trying out the image for us. We are trying to reproduce this on our end but have had no luck so far. Can you please send us the output of show running-config from your router.



    Also we have one more image that we would like you to try it out before the debusg session would that be ok?



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Monday, November 01, 2010 10:22 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------

    Radhika,

    I tried the new OS and still getting same IOS crash.
    As mentioned I will work around your schedule so let me if you were able to get someone from the IOS team to help troubleshoot today.

    Thanks in advance,

    Ken Romo


    Ken,

    I am trying to get some help from the IOS team since this a router crash. So I will setup the webex session to debug for some time Monday so we can collect all the information and try out any suggestion from them.



    For Now We will post a newer IOS image to the beta Site and can you give that a try to see if that will solve the issue.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Friday, October 29, 2010 8:24 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    I will work around your schedule, anytime you are available, I will make myself available.
    email:
    kromo@opentext.com

    Thanks in advance,

    Ken Romo

    +++++++++++++++++++++++++++++++++

    Ken,

    Would a webex session tomorrow morning (any time between 10:00 and 1:00) work for you? Let me know the time that would work for you and also your email address so I can send you a webex invite.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Thursday, October 28, 2010 3:12 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Radhika Miriyala in Service Ready Engine Virtualizatio



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    No worries, we are trying to work this out together and I appreciate the help.
    s/m 1/1 is set as trunk but I went ahead and reconfigured to truank again and reloaded OS and get the same crash when I ping to the MGF interface from the SRE (I attached the errors at the bottom of this message).

    Ken,

    Sorry I just realized the mistake. I meant to say make the interface sm 1/1 as trunk.

    Sorry about the confusion.



    Please try it out.



    Thanks,

    Radhika



    boxer#
    %ALIGN-1-FATAL: Illegal access to a low address 22:02:10 UTC Thu Oct 28 2010
    addr=0x14, pc=0x22765BD8z , ra=0x22765B84z , sp=0x3022FBB8
    %ALIGN-1-FATAL: Illegal access to a low address 22:02:11 UTC Thu Oct 28 2010
    addr=0x14, pc=0x22765BD8z , ra=0x22765B84z , sp=0x3022FBB8

    22:02:11 UTC Thu Oct 28 2010: TLB (store) exception, CPU signal 10, PC = 0x22768478

    --------------------------------------------------------------------
    Possible software fault. Upon reccurence, please collect
    crashinfo, "show tech" and contact Cisco Technical Support.
    --------------------------------------------------------------------

    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z
    $0 : 00000000 00000000, AT : 00000000 29130000, v0 : 00000000 00000001, v1 : 00000000 0D8B8540
    a0 : 00000000 00000000, a1 : 00000000 0D8B8584, a2 : 00000000 2A2F8ABC, a3 : 00000000 00000004
    t0 : 00000000 00000020, t1 : 00000000 500099E1, t2 : 00000000 500081E0, t3 : FFFFFFFF FFFFFFF2
    t4 : 00000000 0000000E, t5 : 00000000 00000000, t6 : 00000000 0D95F890, t7 : 00000000 000001FF
    s0 : 00000000 00000000, s1 : 00000000 2A2FDB40, s2 : FFFFFFFF FFFFFFEC, s3 : 00000000 3080C980
    s4 : 00000000 0D95F89E, s5 : 00000000 2A300EE0, s6 : 00000000 00000000, s7 : 00000000 0000000E
    t8 : 00000000 000007FC, t9 : 00000000 2A300200, k0 : 00000000 00000000, k1 : 00000000 00000000
    gp : 00000000 29133C00, sp : 00000000 3022FBB8, s8 : 00000000 00000054, ra : 00000000 22768424
    EPC : 22768478, ErrorEPC : 80412AB4, SREG : 500099E3
    MDLO : 87126668, MDHI : D990ADBB, BadVaddr : 00000014
    CacheErr_Icache : 0x007F7F00 - 000040D8, CacheErr_Dcache : 0x00000000 - 00001FA0
    TagLo_Icache : 0x00000000 - 23642303, DataLo_Icache : 0xAFBF0018 - 0D81ADDB
    DataHi_Icache: 0x00000000 - 00000001
    TagLo_Dcache : 0x00000000 - 2277E583, TagHi_Dcache : 0x00000000 - 0912BD81
    DataLo_Dcache: 0x00000001 - 2368110C, DataHi_Dcache : 0x00000000 - 0000001C
    TEXT_START : 0x21003178
    DATA_START : 0x260888A0
    Cause 0000040C (Code 0x3): TLB (store) exception

    22:02:11 UTC Thu Oct 28 2010: TLB (store) exception, CPU signal 10, PC = 0x22768478

    --------------------------------------------------------------------
    Possible software fault. Upon reccurence, please collect
    crashinfo, "show tech" and contact Cisco Technical Support.
    --------------------------------------------------------------------

    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z
    $0 : 00000000 00000000, AT : 00000000 29130000, v0 : 00000000 00000001, v1 : 00000000 0D8B8540
    a0 : 00000000 00000000, a1 : 00000000 0D8B8584, a2 : 00000000 2A2F8ABC, a3 : 00000000 00000004
    t0 : 00000000 00000020, t1 : 00000000 500099E1, t2 : 00000000 500081E0, t3 : FFFFFFFF FFFFFFF2
    t4 : 00000000 0000000E, t5 : 00000000 00000000, t6 : 00000000 0D95F890, t7 : 00000000 000001FF
    s0 : 00000000 00000000, s1 : 00000000 2A2FDB40, s2 : FFFFFFFF FFFFFFEC, s3 : 00000000 3080C980
    s4 : 00000000 0D95F89E, s5 : 00000000 2A300EE0, s6 : 00000000 00000000, s7 : 00000000 0000000E
    t8 : 00000000 000007FC, t9 : 00000000 2A300200, k0 : 00000000 00000000, k1 : 00000000 00000000
    gp : 00000000 29133C00, sp : 00000000 3022FBB8, s8 : 00000000 00000054, ra : 00000000 22768424
    EPC : 22768478, ErrorEPC : 80412AB4, SREG : 500099E3
    MDLO : 87126668, MDHI : D990ADBB, BadVaddr : 00000014
    CacheErr_Icache : 0x007F7F00 - 000040D8, CacheErr_Dcache : 0x00000000 - 00001FA0
    TagLo_Icache : 0x00000000 - 23642303, DataLo_Icache : 0xAFBF0018 - 0D81ADDB
    DataHi_Icache: 0x00000000 - 00000001
    TagLo_Dcache : 0x00000000 - 2277E583, TagHi_Dcache : 0x00000000 - 0912BD81
    DataLo_Dcache: 0x00000001 - 2368110C, DataHi_Dcache : 0x00000000 - 0000001C
    TEXT_START : 0x21003178
    DATA_START : 0x260888A0
    Cause 0000040C (Code 0x3): TLB (store) exception
    Writing crashinfo to flash:crashinfo_20101028-220211-UTC
    22:02:11 UTC Thu Oct 28 2010: TLB (store) exception, CPU signal 10, PC = 0x22768478

    --------------------------------------------------------------------
    Possible software fault. Upon reccurence, please collect
    crashinfo, "show tech" and contact Cisco Technical Support.
    --------------------------------------------------------------------

    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z
    $0 : 00000000 00000000, AT : 00000000 29130000, v0 : 00000000 00000001, v1 : 00000000 0D8B8540
    a0 : 00000000 00000000, a1 : 00000000 0D8B8584, a2 : 00000000 2A2F8ABC, a3 : 00000000 00000004
    t0 : 00000000 00000020, t1 : 00000000 500099E1, t2 : 00000000 500081E0, t3 : FFFFFFFF FFFFFFF2
    t4 : 00000000 0000000E, t5 : 00000000 00000000, t6 : 00000000 0D95F890, t7 : 00000000 000001FF
    s0 : 00000000 00000000, s1 : 00000000 2A2FDB40, s2 : FFFFFFFF FFFFFFEC, s3 : 00000000 3080C980
    s4 : 00000000 0D95F89E, s5 : 00000000 2A300EE0, s6 : 00000000 00000000, s7 : 00000000 0000000E
    t8 : 00000000 000007FC, t9 : 00000000 2A300200, k0 : 00000000 00000000, k1 : 00000000 00000000
    gp : 00000000 29133C00, sp : 00000000 3022FBB8, s8 : 00000000 00000054, ra : 00000000 22768424
    EPC : 22768478, ErrorEPC : 80412AB4, SREG : 500099E3
    MDLO : 87126668, MDHI : D990ADBB, BadVaddr : 00000014
    CacheErr_Icache : 0x007F7F00 - 000040D8, CacheErr_Dcache : 0x00000000 - 00001FA0
    TagLo_Icache : 0x00000000 - 23642303, DataLo_Icache : 0xAFBF0018 - 0D81ADDB
    DataHi_Icache: 0x00000000 - 00000001
    TagLo_Dcache : 0x00000000 - 2277E583, TagHi_Dcache : 0x00000000 - 0912BD81
    DataLo_Dcache: 0x00000001 - 2368110C, DataHi_Dcache : 0x00000000 - 0000001C
    TEXT_START : 0x21003178
    DATA_START : 0x260888A0
    Cause 0000040C (Code 0x3): TLB (store) exception
    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z

    === Flushing messages (22:02:12 UTC Thu Oct 28 2010) ===
    Buffered messages:
    *Oct 28 20:52:40.075: %LINK-3-UPDOWN: Interface SM1/0, changed state to up
    *Oct 28 20:52:42.195: %LINK-3-UPDOWN: Interface GigabitEthernet0/0, changed state to up
    *Oct 28 20:52:42.195: %LINK-3-UPDOWN: Interface GigabitEthernet0/1, changed state to down
    *Oct 28 20:52:42.195: %LINK-3-UPDOWN: Interface GigabitEthernet0/2, changed state to down
    *Oct 28 20:52:44.631: %LINK-3-UPDOWN: Interface SM1/1, changed state to up
    *Oct 28 20:53:01.655: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/0, changed state to up
    *Oct 28 20:53:01.923: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/1, changed state to up
    *Oct 28 20:53:02.075: %LINK-3-UPDOWN: Interface Foreign Exchange Station 0/1/0, changed state to up
    *Oct 28 20:53:02.075: %LINK-3-UPDOWN: Interface Foreign Exchange Station 0/1/1, changed state to up
    *Oct 28 20:53:43.739: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/0, changed state to operational status down due to cable removal
    *Oct 28 20:53:44.739: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/1, changed state to operational status down due to cable removal
    Queued messages:
    No warm reboot Storage
    *** System received a Bus Error exception ***
    signal= 0xa, code= 0x40c, context= 0x29726b74
    PC = 0x22768478, SP = 0x3022fbb8, RA = 0x22768424
    Cause Reg = 0x0000040c, Status Reg = 0x500099e3
    System Bootstrap, Version 15.0(1r)M6, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 2010 by cisco Systems, Inc.
    Total memory size = 512 MB - On-board = 512 MB, DIMM0 = 0 MB
    CISCO2911/K9 platform with 524288 Kbytes of main memory
    Main memory is configured to 72/-1(On-board/DIMM0) bit mode with ECC enabled

    Readonly ROMMON initialized
    program load complete, entry point: 0x80803000, size: 0x1b340

    IOS Image Load Test
    ___________________
    Digitally Signed Development Software
    program load complete, entry point: 0x81000000, size: 0x40b6b74
    Self decompressing the image : #############################################################################################################

    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2691036>
    or simply reply to this email.
    -- --
    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2691978>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2699015>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2699042>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2699089>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2699640>
    or simply reply to this email.

    Subject: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-
    Replied by: Ken Romo on 20-11-2010 01:34:36 AM
    Radhika,
     
    The PVDMS is:
     
    PVDM3-16 V01
    S/N FOC14200FNK
     
    Is this what you were looking for?
     
    Ken
     
    Ken,

    I am not sure if it is the PVDM that is bad but it could be a bug in the IOS image also where you have pvdm and the SRE module it could be some issue. For now can you continute to do beta for SRE-v without the PVDMS.



    I will check with the team and get back to you as to how to proceed.



    Can you let me know what PVDM models you have so we can try to reproduce this in our lab.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Monday, November 01, 2010 3:59 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    I pulled the PVDM and it is working.

    Does this mean the PVDM is bad?

    Ken


    Ken,

    Please try out the new image sent by Brett to you when you get a chance. Also one difference we noticed is that you have PVDM¿s in your setup that we don not have in our test setup. Would it be possible to remove the PVDMS temporarily and try the ping? This may help us root cause the issue.



    I will also schedule a WebEx for tomorrow morning 10:30 PST with the IOS developer so we can take a look if the change of IOS image and removal of PVDM¿s does not solve the issue. Please let me know if that time slot does not work for you.



    Thanks,

    Radhika





    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Monday, November 01, 2010 11:19 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    Here you go:

    boxer#show vlan-switch
    VLAN Name Status Ports
    ---- -------------------------------- --------- -------------------------------
    1 default active
    1002 fddi-default act/unsup
    1003 token-ring-default act/unsup
    1004 fddinet-default act/unsup
    1005 trnet-default act/unsup
    VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2
    ---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------
    1 enet 100001 1500 - - - - - 1002 1003
    1002 fddi 101002 1500 - - - - - 1 1003
    1003 tr 101003 1500 1005 0 - - srb 1 1002
    1004 fdnet 101004 1500 - - 1 ibm - 0 0
    1005 trnet 101005 1500 - - 1 ibm - 0 0


    boxer#sh platform mgf module
    Registered Module Information
    Code: NR - Not Registered, TM - Trust Mode, SP - Scheduling Profile
    BL - Buffer Level, TR - Traffic Rate, PT - Pause Threshold
    slot vlan type/ID TM SP BL TR PT
    ---- ---- ---------- ------- --- ------ ----- ----
    ISM NR
    EHWIC-0 NR
    EHWIC-1 NR
    EHWIC-2 NR
    EHWIC-3 NR
    PVDM-0 2 PVDM/5 UP 1 low 1000 low
    PVDM-1 2 PVDM/5 UP 1 low 1000 low
    SM-1 1 Switch/3 UP 1 low 1000 high




    Thanks Ken. Can you also give us the output of the following.



    1) show vlan-switch

    2) ¿show platform mgf module¿ before the crash happens.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Monday, November 01, 2010 10:50 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    I will try whatever you suggest, just let me know when you have posted the new IOS.

    Below is my config:

    boxer#sh run
    Building configuration...

    Current configuration : 5777 bytes
    !
    version 15.1
    service timestamps debug datetime msec
    service timestamps log datetime msec
    no service password-encryption
    !
    hostname boxer
    !
    boot-start-marker
    boot system flash0 c2900-universalk9-mz.SSA.151-2.19.T
    boot-end-marker
    !
    !
    logging buffered 51200 warnings
    !
    no aaa new-model
    !
    no ipv6 cef
    ip source-route
    ip cef
    !
    !
    !
    !
    !
    ip domain name yourdomain.com
    multilink bundle-name authenticated
    !
    !
    !
    !
    !
    crypto pki token default removal timeout 0
    !
    crypto pki trustpoint TP-self-signed-1999750280
    enrollment selfsigned
    subject-name cn=IOS-Self-Signed-Certificate-1999750280
    revocation-check none
    rsakeypair TP-self-signed-1999750280
    !
    !
    crypto pki certificate chain TP-self-signed-1999750280
    certificate self-signed 01
    3082024C 308201B5 A0030201 02020101 300D0609 2A864886 F70D0101 04050030
    31312F30 2D060355 04031326 494F532D 53656C66 2D536967 6E65642D 43657274
    69666963 6174652D 31393939 37353032 3830301E 170D3130 31303230 32323335
    32365A17 0D323030 31303130 30303030 305A3031 312F302D 06035504 03132649
    4F532D53 656C662D 5369676E 65642D43 65727469 66696361 74652D31 39393937
    35303238 3030819F 300D0609 2A864886 F70D0101 01050003 818D0030 81890281
    81009378 2E139D79 DCA59865 14AB3398 870362B7 40BB9C13 A5DC5315 6108DF92
    5E78CF06 A40D4DB5 B66D410E FAFE75AC 764997B1 5C551A47 CFA00109 520352EC
    33A69E24 B3C1175B 136FC62A 8BE4637E B834059B FC7CAA6E 957DA0BB 66D8DC49
    80F82890 981FFCFE 0DC7E6F9 53287989 3887C5F6 AF59D0BE B502E11E FD16F556
    DBB90203 010001A3 74307230 0F060355 1D130101 FF040530 030101FF 301F0603
    551D1104 18301682 14626F78 65722E79 6F757264 6F6D6169 6E2E636F 6D301F06
    03551D23 04183016 80143541 7934E424 4B9A60DB E6C908C3 C20BAA17 D058301D
    0603551D 0E041604 14354179 34E4244B 9A60DBE6 C908C3C2 0BAA17D0 58300D06
    092A8648 86F70D01 01040500 03818100 3D222AB5 177D452F 153DCA26 1D7ECB49
    58BCBF60 DA18DC04 94B82EA3 76884EBC D7131641 08687C04 6C6645DF 78B2D2F8
    409BCAD7 50AF5091 B99614FD C2424D89 407A9109 BCA20473 F4CE33D4 4B126483
    C240C0B9 7A628E53 E419FEC3 B8853671 03113F5E 47FA8120 9F9A7A9D 11498FE0
    82C96578 8FD9770A EBD27F73 DF2E1487
    quit
    voice-card 0
    !
    !
    !
    !
    !
    !
    !
    license udi pid CISCO2911/K9 sn FTX1422A077
    hw-module pvdm 0/0
    !
    hw-module sm 1
    !
    !
    !
    username jack privilege 15 secret 5 $1$c5QR$fYGTbhWRKsBZ1JpNyIQGG1
    username marco privilege 15 secret 5 $1$amqq$5pI0T7mUViDL5Y.NqX/yz.
    !
    redundancy
    !
    !
    !
    !
    !
    !
    interface GigabitEthernet0/0
    description To tusqa network
    ip address 172.17.17.130 255.255.248.0
    duplex auto
    speed auto
    !
    interface GigabitEthernet0/1
    no ip address
    shutdown
    duplex auto
    speed auto
    !
    interface GigabitEthernet0/2
    no ip address
    shutdown
    duplex auto
    speed auto
    !
    interface SM1/0
    ip unnumbered GigabitEthernet0/0
    service-module ip address 172.17.17.129 255.255.248.0
    !Application: SRE-V Running on SMV
    service-module ip default-gateway 172.17.17.130
    service-module mgf ip address 10.62.64.1 255.255.255.0
    service-module mgf ip default-gateway 10.62.64.2
    !
    interface SM1/1
    description Internal switch interface connected to Service Module
    switchport mode trunk
    !
    interface Vlan1
    ip address 10.62.64.2 255.255.255.0
    !
    ip forward-protocol nd
    !
    ip http server
    ip http access-class 23
    ip http authentication local
    ip http secure-server
    ip http timeout-policy idle 60 life 86400 requests 10000
    !
    ip route 172.17.17.129 255.255.255.255 SM1/0
    !
    !
    !
    !
    control-plane
    !
    !
    voice-port 0/0/0
    !
    voice-port 0/0/1
    !
    voice-port 0/1/0
    !
    voice-port 0/1/1
    !
    !
    !
    mgcp profile default
    !
    !
    !
    !
    !
    gatekeeper
    shutdown
    !
    !
    banner exec ^C
    % Password expiration warning.
    -----------------------------------------------------------------------
    Cisco Configuration Professional (Cisco CP) is installed on this device
    and it provides the default username "cisco" for one-time use. If you have
    already used the username "cisco" to login to the router and your IOS image
    supports the "one-time" user option, then this username has already expired.
    You will not be able to login to the router with this username after you exit
    this session.
    It is strongly suggested that you create a new username with a privilege level
    of 15 using the following command.
    username <myuser> privilege 15 secret 0 <mypassword>
    Replace <myuser> and <mypassword> with the username and password you want to
    use.
    -----------------------------------------------------------------------
    ^C
    banner login ^C
    -----------------------------------------------------------------------
    Cisco Configuration Professional (Cisco CP) is installed on this device.
    This feature requires the one-time use of the username "cisco" with the
    password "cisco". These default credentials have a privilege level of 15.
    YOU MUST USE CISCO CP or the CISCO IOS CLI TO CHANGE THESE PUBLICLY-KNOWN
    CREDENTIALS
    Here are the Cisco IOS commands.
    username <myuser> privilege 15 secret 0 <mypassword>
    no username cisco
    Replace <myuser> and <mypassword> with the username and password you want
    to use.
    IF YOU DO NOT CHANGE THE PUBLICLY-KNOWN CREDENTIALS, YOU WILL NOT BE ABLE
    TO LOG INTO THE DEVICE AGAIN AFTER YOU HAVE LOGGED OFF.
    For more information about Cisco CP please follow the instructions in the
    QUICK START GUIDE for your router or go to http://www.cisco.com/go/ciscocp
    -----------------------------------------------------------------------
    ^C
    !
    line con 0
    login local
    line aux 0
    line 67
    no activation-character
    no exec
    transport preferred none
    transport input all
    transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
    stopbits 1
    flowcontrol software
    line vty 0 4
    privilege level 15
    login local
    transport input telnet
    line vty 5 15
    privilege level 15
    login local
    transport input telnet ssh
    !
    exception data-corruption buffer truncate
    scheduler allocate 20000 1000
    end



    Ken, Thanks for trying out the image for us. We are trying to reproduce this on our end but have had no luck so far. Can you please send us the output of show running-config from your router.



    Also we have one more image that we would like you to try it out before the debusg session would that be ok?



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Monday, November 01, 2010 10:22 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------

    Radhika,

    I tried the new OS and still getting same IOS crash.
    As mentioned I will work around your schedule so let me if you were able to get someone from the IOS team to help troubleshoot today.

    Thanks in advance,

    Ken Romo


    Ken,

    I am trying to get some help from the IOS team since this a router crash. So I will setup the webex session to debug for some time Monday so we can collect all the information and try out any suggestion from them.



    For Now We will post a newer IOS image to the beta Site and can you give that a try to see if that will solve the issue.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Friday, October 29, 2010 8:24 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    I will work around your schedule, anytime you are available, I will make myself available.
    email:
    kromo@opentext.com

    Thanks in advance,

    Ken Romo

    +++++++++++++++++++++++++++++++++

    Ken,

    Would a webex session tomorrow morning (any time between 10:00 and 1:00) work for you? Let me know the time that would work for you and also your email address so I can send you a webex invite.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Thursday, October 28, 2010 3:12 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Radhika Miriyala in Service Ready Engine Virtualizatio



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    No worries, we are trying to work this out together and I appreciate the help.
    s/m 1/1 is set as trunk but I went ahead and reconfigured to truank again and reloaded OS and get the same crash when I ping to the MGF interface from the SRE (I attached the errors at the bottom of this message).

    Ken,

    Sorry I just realized the mistake. I meant to say make the interface sm 1/1 as trunk.

    Sorry about the confusion.



    Please try it out.



    Thanks,

    Radhika



    boxer#
    %ALIGN-1-FATAL: Illegal access to a low address 22:02:10 UTC Thu Oct 28 2010
    addr=0x14, pc=0x22765BD8z , ra=0x22765B84z , sp=0x3022FBB8
    %ALIGN-1-FATAL: Illegal access to a low address 22:02:11 UTC Thu Oct 28 2010
    addr=0x14, pc=0x22765BD8z , ra=0x22765B84z , sp=0x3022FBB8

    22:02:11 UTC Thu Oct 28 2010: TLB (store) exception, CPU signal 10, PC = 0x22768478

    --------------------------------------------------------------------
    Possible software fault. Upon reccurence, please collect
    crashinfo, "show tech" and contact Cisco Technical Support.
    --------------------------------------------------------------------

    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z
    $0 : 00000000 00000000, AT : 00000000 29130000, v0 : 00000000 00000001, v1 : 00000000 0D8B8540
    a0 : 00000000 00000000, a1 : 00000000 0D8B8584, a2 : 00000000 2A2F8ABC, a3 : 00000000 00000004
    t0 : 00000000 00000020, t1 : 00000000 500099E1, t2 : 00000000 500081E0, t3 : FFFFFFFF FFFFFFF2
    t4 : 00000000 0000000E, t5 : 00000000 00000000, t6 : 00000000 0D95F890, t7 : 00000000 000001FF
    s0 : 00000000 00000000, s1 : 00000000 2A2FDB40, s2 : FFFFFFFF FFFFFFEC, s3 : 00000000 3080C980
    s4 : 00000000 0D95F89E, s5 : 00000000 2A300EE0, s6 : 00000000 00000000, s7 : 00000000 0000000E
    t8 : 00000000 000007FC, t9 : 00000000 2A300200, k0 : 00000000 00000000, k1 : 00000000 00000000
    gp : 00000000 29133C00, sp : 00000000 3022FBB8, s8 : 00000000 00000054, ra : 00000000 22768424
    EPC : 22768478, ErrorEPC : 80412AB4, SREG : 500099E3
    MDLO : 87126668, MDHI : D990ADBB, BadVaddr : 00000014
    CacheErr_Icache : 0x007F7F00 - 000040D8, CacheErr_Dcache : 0x00000000 - 00001FA0
    TagLo_Icache : 0x00000000 - 23642303, DataLo_Icache : 0xAFBF0018 - 0D81ADDB
    DataHi_Icache: 0x00000000 - 00000001
    TagLo_Dcache : 0x00000000 - 2277E583, TagHi_Dcache : 0x00000000 - 0912BD81
    DataLo_Dcache: 0x00000001 - 2368110C, DataHi_Dcache : 0x00000000 - 0000001C
    TEXT_START : 0x21003178
    DATA_START : 0x260888A0
    Cause 0000040C (Code 0x3): TLB (store) exception

    22:02:11 UTC Thu Oct 28 2010: TLB (store) exception, CPU signal 10, PC = 0x22768478

    --------------------------------------------------------------------
    Possible software fault. Upon reccurence, please collect
    crashinfo, "show tech" and contact Cisco Technical Support.
    --------------------------------------------------------------------

    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z
    $0 : 00000000 00000000, AT : 00000000 29130000, v0 : 00000000 00000001, v1 : 00000000 0D8B8540
    a0 : 00000000 00000000, a1 : 00000000 0D8B8584, a2 : 00000000 2A2F8ABC, a3 : 00000000 00000004
    t0 : 00000000 00000020, t1 : 00000000 500099E1, t2 : 00000000 500081E0, t3 : FFFFFFFF FFFFFFF2
    t4 : 00000000 0000000E, t5 : 00000000 00000000, t6 : 00000000 0D95F890, t7 : 00000000 000001FF
    s0 : 00000000 00000000, s1 : 00000000 2A2FDB40, s2 : FFFFFFFF FFFFFFEC, s3 : 00000000 3080C980
    s4 : 00000000 0D95F89E, s5 : 00000000 2A300EE0, s6 : 00000000 00000000, s7 : 00000000 0000000E
    t8 : 00000000 000007FC, t9 : 00000000 2A300200, k0 : 00000000 00000000, k1 : 00000000 00000000
    gp : 00000000 29133C00, sp : 00000000 3022FBB8, s8 : 00000000 00000054, ra : 00000000 22768424
    EPC : 22768478, ErrorEPC : 80412AB4, SREG : 500099E3
    MDLO : 87126668, MDHI : D990ADBB, BadVaddr : 00000014
    CacheErr_Icache : 0x007F7F00 - 000040D8, CacheErr_Dcache : 0x00000000 - 00001FA0
    TagLo_Icache : 0x00000000 - 23642303, DataLo_Icache : 0xAFBF0018 - 0D81ADDB
    DataHi_Icache: 0x00000000 - 00000001
    TagLo_Dcache : 0x00000000 - 2277E583, TagHi_Dcache : 0x00000000 - 0912BD81
    DataLo_Dcache: 0x00000001 - 2368110C, DataHi_Dcache : 0x00000000 - 0000001C
    TEXT_START : 0x21003178
    DATA_START : 0x260888A0
    Cause 0000040C (Code 0x3): TLB (store) exception
    Writing crashinfo to flash:crashinfo_20101028-220211-UTC
    22:02:11 UTC Thu Oct 28 2010: TLB (store) exception, CPU signal 10, PC = 0x22768478

    --------------------------------------------------------------------
    Possible software fault. Upon reccurence, please collect
    crashinfo, "show tech" and contact Cisco Technical Support.
    --------------------------------------------------------------------

    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z
    $0 : 00000000 00000000, AT : 00000000 29130000, v0 : 00000000 00000001, v1 : 00000000 0D8B8540
    a0 : 00000000 00000000, a1 : 00000000 0D8B8584, a2 : 00000000 2A2F8ABC, a3 : 00000000 00000004
    t0 : 00000000 00000020, t1 : 00000000 500099E1, t2 : 00000000 500081E0, t3 : FFFFFFFF FFFFFFF2
    t4 : 00000000 0000000E, t5 : 00000000 00000000, t6 : 00000000 0D95F890, t7 : 00000000 000001FF
    s0 : 00000000 00000000, s1 : 00000000 2A2FDB40, s2 : FFFFFFFF FFFFFFEC, s3 : 00000000 3080C980
    s4 : 00000000 0D95F89E, s5 : 00000000 2A300EE0, s6 : 00000000 00000000, s7 : 00000000 0000000E
    t8 : 00000000 000007FC, t9 : 00000000 2A300200, k0 : 00000000 00000000, k1 : 00000000 00000000
    gp : 00000000 29133C00, sp : 00000000 3022FBB8, s8 : 00000000 00000054, ra : 00000000 22768424
    EPC : 22768478, ErrorEPC : 80412AB4, SREG : 500099E3
    MDLO : 87126668, MDHI : D990ADBB, BadVaddr : 00000014
    CacheErr_Icache : 0x007F7F00 - 000040D8, CacheErr_Dcache : 0x00000000 - 00001FA0
    TagLo_Icache : 0x00000000 - 23642303, DataLo_Icache : 0xAFBF0018 - 0D81ADDB
    DataHi_Icache: 0x00000000 - 00000001
    TagLo_Dcache : 0x00000000 - 2277E583, TagHi_Dcache : 0x00000000 - 0912BD81
    DataLo_Dcache: 0x00000001 - 2368110C, DataHi_Dcache : 0x00000000 - 0000001C
    TEXT_START : 0x21003178
    DATA_START : 0x260888A0
    Cause 0000040C (Code 0x3): TLB (store) exception
    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z

    === Flushing messages (22:02:12 UTC Thu Oct 28 2010) ===
    Buffered messages:
    *Oct 28 20:52:40.075: %LINK-3-UPDOWN: Interface SM1/0, changed state to up
    *Oct 28 20:52:42.195: %LINK-3-UPDOWN: Interface GigabitEthernet0/0, changed state to up
    *Oct 28 20:52:42.195: %LINK-3-UPDOWN: Interface GigabitEthernet0/1, changed state to down
    *Oct 28 20:52:42.195: %LINK-3-UPDOWN: Interface GigabitEthernet0/2, changed state to down
    *Oct 28 20:52:44.631: %LINK-3-UPDOWN: Interface SM1/1, changed state to up
    *Oct 28 20:53:01.655: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/0, changed state to up
    *Oct 28 20:53:01.923: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/1, changed state to up
    *Oct 28 20:53:02.075: %LINK-3-UPDOWN: Interface Foreign Exchange Station 0/1/0, changed state to up
    *Oct 28 20:53:02.075: %LINK-3-UPDOWN: Interface Foreign Exchange Station 0/1/1, changed state to up
    *Oct 28 20:53:43.739: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/0, changed state to operational status down due to cable removal
    *Oct 28 20:53:44.739: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/1, changed state to operational status down due to cable removal
    Queued messages:
    No warm reboot Storage
    *** System received a Bus Error exception ***
    signal= 0xa, code= 0x40c, context= 0x29726b74
    PC = 0x22768478, SP = 0x3022fbb8, RA = 0x22768424
    Cause Reg = 0x0000040c, Status Reg = 0x500099e3
    System Bootstrap, Version 15.0(1r)M6, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 2010 by cisco Systems, Inc.
    Total memory size = 512 MB - On-board = 512 MB, DIMM0 = 0 MB
    CISCO2911/K9 platform with 524288 Kbytes of main memory
    Main memory is configured to 72/-1(On-board/DIMM0) bit mode with ECC enabled

    Readonly ROMMON initialized
    program load complete, entry point: 0x80803000, size: 0x1b340

    IOS Image Load Test
    ___________________
    Digitally Signed Development Software
    program load complete, entry point: 0x81000000, size: 0x40b6b74
    Self decompressing the image : #############################################################################################################

    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2691036>
    or simply reply to this email.
    -- --
    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2691978>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2699015>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2699042>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2699089>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2699640>
    or simply reply to this email.


    Subject: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-
    Replied by: Radhika Miriyala on 20-11-2010 01:34:36 AM
    Ken,

    Thanks for the information.  We will check internally if this has been tested. I will cancel the debug session for today since we most likely have the root cause for the issue. We will try to reproduce this internally and if we need further information from you will setup a different session.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Tuesday, November 02, 2010 8:49 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    The PVDMS is:

    PVDM3-16 V01
    S/N FOC14200FNK

    Is this what you were looking for?

    Ken


    Ken,

    I am not sure if it is the PVDM that is bad but it could be a bug in the IOS image also where you have pvdm and the SRE module it could be some issue. For now can you continute to do beta for SRE-v without the PVDMS.



    I will check with the team and get back to you as to how to proceed.



    Can you let me know what PVDM models you have so we can try to reproduce this in our lab.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Monday, November 01, 2010 3:59 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    I pulled the PVDM and it is working.

    Does this mean the PVDM is bad?

    Ken


    Ken,

    Please try out the new image sent by Brett to you when you get a chance. Also one difference we noticed is that you have PVDM¿s in your setup that we don not have in our test setup. Would it be possible to remove the PVDMS temporarily and try the ping? This may help us root cause the issue.



    I will also schedule a WebEx for tomorrow morning 10:30 PST with the IOS developer so we can take a look if the change of IOS image and removal of PVDM¿s does not solve the issue. Please let me know if that time slot does not work for you.



    Thanks,

    Radhika





    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Monday, November 01, 2010 11:19 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    Here you go:

    boxer#show vlan-switch
    VLAN Name Status Ports
    ---- -------------------------------- --------- -------------------------------
    1 default active
    1002 fddi-default act/unsup
    1003 token-ring-default act/unsup
    1004 fddinet-default act/unsup
    1005 trnet-default act/unsup
    VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2
    ---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------
    1 enet 100001 1500 - - - - - 1002 1003
    1002 fddi 101002 1500 - - - - - 1 1003
    1003 tr 101003 1500 1005 0 - - srb 1 1002
    1004 fdnet 101004 1500 - - 1 ibm - 0 0
    1005 trnet 101005 1500 - - 1 ibm - 0 0


    boxer#sh platform mgf module
    Registered Module Information
    Code: NR - Not Registered, TM - Trust Mode, SP - Scheduling Profile
    BL - Buffer Level, TR - Traffic Rate, PT - Pause Threshold
    slot vlan type/ID TM SP BL TR PT
    ---- ---- ---------- ------- --- ------ ----- ----
    ISM NR
    EHWIC-0 NR
    EHWIC-1 NR
    EHWIC-2 NR
    EHWIC-3 NR
    PVDM-0 2 PVDM/5 UP 1 low 1000 low
    PVDM-1 2 PVDM/5 UP 1 low 1000 low
    SM-1 1 Switch/3 UP 1 low 1000 high




    Thanks Ken. Can you also give us the output of the following.



    1) show vlan-switch

    2) ¿show platform mgf module¿ before the crash happens.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Monday, November 01, 2010 10:50 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    I will try whatever you suggest, just let me know when you have posted the new IOS.

    Below is my config:

    boxer#sh run
    Building configuration...

    Current configuration : 5777 bytes
    !
    version 15.1
    service timestamps debug datetime msec
    service timestamps log datetime msec
    no service password-encryption
    !
    hostname boxer
    !
    boot-start-marker
    boot system flash0 c2900-universalk9-mz.SSA.151-2.19.T
    boot-end-marker
    !
    !
    logging buffered 51200 warnings
    !
    no aaa new-model
    !
    no ipv6 cef
    ip source-route
    ip cef
    !
    !
    !
    !
    !
    ip domain name yourdomain.com
    multilink bundle-name authenticated
    !
    !
    !
    !
    !
    crypto pki token default removal timeout 0
    !
    crypto pki trustpoint TP-self-signed-1999750280
    enrollment selfsigned
    subject-name cn=IOS-Self-Signed-Certificate-1999750280
    revocation-check none
    rsakeypair TP-self-signed-1999750280
    !
    !
    crypto pki certificate chain TP-self-signed-1999750280
    certificate self-signed 01
    3082024C 308201B5 A0030201 02020101 300D0609 2A864886 F70D0101 04050030
    31312F30 2D060355 04031326 494F532D 53656C66 2D536967 6E65642D 43657274
    69666963 6174652D 31393939 37353032 3830301E 170D3130 31303230 32323335
    32365A17 0D323030 31303130 30303030 305A3031 312F302D 06035504 03132649
    4F532D53 656C662D 5369676E 65642D43 65727469 66696361 74652D31 39393937
    35303238 3030819F 300D0609 2A864886 F70D0101 01050003 818D0030 81890281
    81009378 2E139D79 DCA59865 14AB3398 870362B7 40BB9C13 A5DC5315 6108DF92
    5E78CF06 A40D4DB5 B66D410E FAFE75AC 764997B1 5C551A47 CFA00109 520352EC
    33A69E24 B3C1175B 136FC62A 8BE4637E B834059B FC7CAA6E 957DA0BB 66D8DC49
    80F82890 981FFCFE 0DC7E6F9 53287989 3887C5F6 AF59D0BE B502E11E FD16F556
    DBB90203 010001A3 74307230 0F060355 1D130101 FF040530 030101FF 301F0603
    551D1104 18301682 14626F78 65722E79 6F757264 6F6D6169 6E2E636F 6D301F06
    03551D23 04183016 80143541 7934E424 4B9A60DB E6C908C3 C20BAA17 D058301D
    0603551D 0E041604 14354179 34E4244B 9A60DBE6 C908C3C2 0BAA17D0 58300D06
    092A8648 86F70D01 01040500 03818100 3D222AB5 177D452F 153DCA26 1D7ECB49
    58BCBF60 DA18DC04 94B82EA3 76884EBC D7131641 08687C04 6C6645DF 78B2D2F8
    409BCAD7 50AF5091 B99614FD C2424D89 407A9109 BCA20473 F4CE33D4 4B126483
    C240C0B9 7A628E53 E419FEC3 B8853671 03113F5E 47FA8120 9F9A7A9D 11498FE0
    82C96578 8FD9770A EBD27F73 DF2E1487
    quit
    voice-card 0
    !
    !
    !
    !
    !
    !
    !
    license udi pid CISCO2911/K9 sn FTX1422A077
    hw-module pvdm 0/0
    !
    hw-module sm 1
    !
    !
    !
    username jack privilege 15 secret 5 $1$c5QR$fYGTbhWRKsBZ1JpNyIQGG1
    username marco privilege 15 secret 5 $1$amqq$5pI0T7mUViDL5Y.NqX/yz.
    !
    redundancy
    !
    !
    !
    !
    !
    !
    interface GigabitEthernet0/0
    description To tusqa network
    ip address 172.17.17.130 255.255.248.0
    duplex auto
    speed auto
    !
    interface GigabitEthernet0/1
    no ip address
    shutdown
    duplex auto
    speed auto
    !
    interface GigabitEthernet0/2
    no ip address
    shutdown
    duplex auto
    speed auto
    !
    interface SM1/0
    ip unnumbered GigabitEthernet0/0
    service-module ip address 172.17.17.129 255.255.248.0
    !Application: SRE-V Running on SMV
    service-module ip default-gateway 172.17.17.130
    service-module mgf ip address 10.62.64.1 255.255.255.0
    service-module mgf ip default-gateway 10.62.64.2
    !
    interface SM1/1
    description Internal switch interface connected to Service Module
    switchport mode trunk
    !
    interface Vlan1
    ip address 10.62.64.2 255.255.255.0
    !
    ip forward-protocol nd
    !
    ip http server
    ip http access-class 23
    ip http authentication local
    ip http secure-server
    ip http timeout-policy idle 60 life 86400 requests 10000
    !
    ip route 172.17.17.129 255.255.255.255 SM1/0
    !
    !
    !
    !
    control-plane
    !
    !
    voice-port 0/0/0
    !
    voice-port 0/0/1
    !
    voice-port 0/1/0
    !
    voice-port 0/1/1
    !
    !
    !
    mgcp profile default
    !
    !
    !
    !
    !
    gatekeeper
    shutdown
    !
    !
    banner exec ^C
    % Password expiration warning.
    -----------------------------------------------------------------------
    Cisco Configuration Professional (Cisco CP) is installed on this device
    and it provides the default username "cisco" for one-time use. If you have
    already used the username "cisco" to login to the router and your IOS image
    supports the "one-time" user option, then this username has already expired.
    You will not be able to login to the router with this username after you exit
    this session.
    It is strongly suggested that you create a new username with a privilege level
    of 15 using the following command.
    username <myuser> privilege 15 secret 0 <mypassword>
    Replace <myuser> and <mypassword> with the username and password you want to
    use.
    -----------------------------------------------------------------------
    ^C
    banner login ^C
    -----------------------------------------------------------------------
    Cisco Configuration Professional (Cisco CP) is installed on this device.
    This feature requires the one-time use of the username "cisco" with the
    password "cisco". These default credentials have a privilege level of 15.
    YOU MUST USE CISCO CP or the CISCO IOS CLI TO CHANGE THESE PUBLICLY-KNOWN
    CREDENTIALS
    Here are the Cisco IOS commands.
    username <myuser> privilege 15 secret 0 <mypassword>
    no username cisco
    Replace <myuser> and <mypassword> with the username and password you want
    to use.
    IF YOU DO NOT CHANGE THE PUBLICLY-KNOWN CREDENTIALS, YOU WILL NOT BE ABLE
    TO LOG INTO THE DEVICE AGAIN AFTER YOU HAVE LOGGED OFF.
    For more information about Cisco CP please follow the instructions in the
    QUICK START GUIDE for your router or go to http://www.cisco.com/go/ciscocp
    -----------------------------------------------------------------------
    ^C
    !
    line con 0
    login local
    line aux 0
    line 67
    no activation-character
    no exec
    transport preferred none
    transport input all
    transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
    stopbits 1
    flowcontrol software
    line vty 0 4
    privilege level 15
    login local
    transport input telnet
    line vty 5 15
    privilege level 15
    login local
    transport input telnet ssh
    !
    exception data-corruption buffer truncate
    scheduler allocate 20000 1000
    end



    Ken, Thanks for trying out the image for us. We are trying to reproduce this on our end but have had no luck so far. Can you please send us the output of show running-config from your router.



    Also we have one more image that we would like you to try it out before the debusg session would that be ok?



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Monday, November 01, 2010 10:22 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------

    Radhika,

    I tried the new OS and still getting same IOS crash.
    As mentioned I will work around your schedule so let me if you were able to get someone from the IOS team to help troubleshoot today.

    Thanks in advance,

    Ken Romo


    Ken,

    I am trying to get some help from the IOS team since this a router crash. So I will setup the webex session to debug for some time Monday so we can collect all the information and try out any suggestion from them.



    For Now We will post a newer IOS image to the beta Site and can you give that a try to see if that will solve the issue.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Friday, October 29, 2010 8:24 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    I will work around your schedule, anytime you are available, I will make myself available.
    email:
    kromo@opentext.com

    Thanks in advance,

    Ken Romo

    +++++++++++++++++++++++++++++++++

    Ken,

    Would a webex session tomorrow morning (any time between 10:00 and 1:00) work for you? Let me know the time that would work for you and also your email address so I can send you a webex invite.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Thursday, October 28, 2010 3:12 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Radhika Miriyala in Service Ready Engine Virtualizatio



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    No worries, we are trying to work this out together and I appreciate the help.
    s/m 1/1 is set as trunk but I went ahead and reconfigured to truank again and reloaded OS and get the same crash when I ping to the MGF interface from the SRE (I attached the errors at the bottom of this message).

    Ken,

    Sorry I just realized the mistake. I meant to say make the interface sm 1/1 as trunk.

    Sorry about the confusion.



    Please try it out.



    Thanks,

    Radhika



    boxer#
    %ALIGN-1-FATAL: Illegal access to a low address 22:02:10 UTC Thu Oct 28 2010
    addr=0x14, pc=0x22765BD8z , ra=0x22765B84z , sp=0x3022FBB8
    %ALIGN-1-FATAL: Illegal access to a low address 22:02:11 UTC Thu Oct 28 2010
    addr=0x14, pc=0x22765BD8z , ra=0x22765B84z , sp=0x3022FBB8

    22:02:11 UTC Thu Oct 28 2010: TLB (store) exception, CPU signal 10, PC = 0x22768478

    --------------------------------------------------------------------
    Possible software fault. Upon reccurence, please collect
    crashinfo, "show tech" and contact Cisco Technical Support.
    --------------------------------------------------------------------

    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z
    $0 : 00000000 00000000, AT : 00000000 29130000, v0 : 00000000 00000001, v1 : 00000000 0D8B8540
    a0 : 00000000 00000000, a1 : 00000000 0D8B8584, a2 : 00000000 2A2F8ABC, a3 : 00000000 00000004
    t0 : 00000000 00000020, t1 : 00000000 500099E1, t2 : 00000000 500081E0, t3 : FFFFFFFF FFFFFFF2
    t4 : 00000000 0000000E, t5 : 00000000 00000000, t6 : 00000000 0D95F890, t7 : 00000000 000001FF
    s0 : 00000000 00000000, s1 : 00000000 2A2FDB40, s2 : FFFFFFFF FFFFFFEC, s3 : 00000000 3080C980
    s4 : 00000000 0D95F89E, s5 : 00000000 2A300EE0, s6 : 00000000 00000000, s7 : 00000000 0000000E
    t8 : 00000000 000007FC, t9 : 00000000 2A300200, k0 : 00000000 00000000, k1 : 00000000 00000000
    gp : 00000000 29133C00, sp : 00000000 3022FBB8, s8 : 00000000 00000054, ra : 00000000 22768424
    EPC : 22768478, ErrorEPC : 80412AB4, SREG : 500099E3
    MDLO : 87126668, MDHI : D990ADBB, BadVaddr : 00000014
    CacheErr_Icache : 0x007F7F00 - 000040D8, CacheErr_Dcache : 0x00000000 - 00001FA0
    TagLo_Icache : 0x00000000 - 23642303, DataLo_Icache : 0xAFBF0018 - 0D81ADDB
    DataHi_Icache: 0x00000000 - 00000001
    TagLo_Dcache : 0x00000000 - 2277E583, TagHi_Dcache : 0x00000000 - 0912BD81
    DataLo_Dcache: 0x00000001 - 2368110C, DataHi_Dcache : 0x00000000 - 0000001C
    TEXT_START : 0x21003178
    DATA_START : 0x260888A0
    Cause 0000040C (Code 0x3): TLB (store) exception

    22:02:11 UTC Thu Oct 28 2010: TLB (store) exception, CPU signal 10, PC = 0x22768478

    --------------------------------------------------------------------
    Possible software fault. Upon reccurence, please collect
    crashinfo, "show tech" and contact Cisco Technical Support.
    --------------------------------------------------------------------

    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z
    $0 : 00000000 00000000, AT : 00000000 29130000, v0 : 00000000 00000001, v1 : 00000000 0D8B8540
    a0 : 00000000 00000000, a1 : 00000000 0D8B8584, a2 : 00000000 2A2F8ABC, a3 : 00000000 00000004
    t0 : 00000000 00000020, t1 : 00000000 500099E1, t2 : 00000000 500081E0, t3 : FFFFFFFF FFFFFFF2
    t4 : 00000000 0000000E, t5 : 00000000 00000000, t6 : 00000000 0D95F890, t7 : 00000000 000001FF
    s0 : 00000000 00000000, s1 : 00000000 2A2FDB40, s2 : FFFFFFFF FFFFFFEC, s3 : 00000000 3080C980
    s4 : 00000000 0D95F89E, s5 : 00000000 2A300EE0, s6 : 00000000 00000000, s7 : 00000000 0000000E
    t8 : 00000000 000007FC, t9 : 00000000 2A300200, k0 : 00000000 00000000, k1 : 00000000 00000000
    gp : 00000000 29133C00, sp : 00000000 3022FBB8, s8 : 00000000 00000054, ra : 00000000 22768424
    EPC : 22768478, ErrorEPC : 80412AB4, SREG : 500099E3
    MDLO : 87126668, MDHI : D990ADBB, BadVaddr : 00000014
    CacheErr_Icache : 0x007F7F00 - 000040D8, CacheErr_Dcache : 0x00000000 - 00001FA0
    TagLo_Icache : 0x00000000 - 23642303, DataLo_Icache : 0xAFBF0018 - 0D81ADDB
    DataHi_Icache: 0x00000000 - 00000001
    TagLo_Dcache : 0x00000000 - 2277E583, TagHi_Dcache : 0x00000000 - 0912BD81
    DataLo_Dcache: 0x00000001 - 2368110C, DataHi_Dcache : 0x00000000 - 0000001C
    TEXT_START : 0x21003178
    DATA_START : 0x260888A0
    Cause 0000040C (Code 0x3): TLB (store) exception
    Writing crashinfo to flash:crashinfo_20101028-220211-UTC
    22:02:11 UTC Thu Oct 28 2010: TLB (store) exception, CPU signal 10, PC = 0x22768478

    --------------------------------------------------------------------
    Possible software fault. Upon reccurence, please collect
    crashinfo, "show tech" and contact Cisco Technical Support.
    --------------------------------------------------------------------

    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z
    $0 : 00000000 00000000, AT : 00000000 29130000, v0 : 00000000 00000001, v1 : 00000000 0D8B8540
    a0 : 00000000 00000000, a1 : 00000000 0D8B8584, a2 : 00000000 2A2F8ABC, a3 : 00000000 00000004
    t0 : 00000000 00000020, t1 : 00000000 500099E1, t2 : 00000000 500081E0, t3 : FFFFFFFF FFFFFFF2
    t4 : 00000000 0000000E, t5 : 00000000 00000000, t6 : 00000000 0D95F890, t7 : 00000000 000001FF
    s0 : 00000000 00000000, s1 : 00000000 2A2FDB40, s2 : FFFFFFFF FFFFFFEC, s3 : 00000000 3080C980
    s4 : 00000000 0D95F89E, s5 : 00000000 2A300EE0, s6 : 00000000 00000000, s7 : 00000000 0000000E
    t8 : 00000000 000007FC, t9 : 00000000 2A300200, k0 : 00000000 00000000, k1 : 00000000 00000000
    gp : 00000000 29133C00, sp : 00000000 3022FBB8, s8 : 00000000 00000054, ra : 00000000 22768424
    EPC : 22768478, ErrorEPC : 80412AB4, SREG : 500099E3
    MDLO : 87126668, MDHI : D990ADBB, BadVaddr : 00000014
    CacheErr_Icache : 0x007F7F00 - 000040D8, CacheErr_Dcache : 0x00000000 - 00001FA0
    TagLo_Icache : 0x00000000 - 23642303, DataLo_Icache : 0xAFBF0018 - 0D81ADDB
    DataHi_Icache: 0x00000000 - 00000001
    TagLo_Dcache : 0x00000000 - 2277E583, TagHi_Dcache : 0x00000000 - 0912BD81
    DataLo_Dcache: 0x00000001 - 2368110C, DataHi_Dcache : 0x00000000 - 0000001C
    TEXT_START : 0x21003178
    DATA_START : 0x260888A0
    Cause 0000040C (Code 0x3): TLB (store) exception
    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z

    === Flushing messages (22:02:12 UTC Thu Oct 28 2010) ===
    Buffered messages:
    *Oct 28 20:52:40.075: %LINK-3-UPDOWN: Interface SM1/0, changed state to up
    *Oct 28 20:52:42.195: %LINK-3-UPDOWN: Interface GigabitEthernet0/0, changed state to up
    *Oct 28 20:52:42.195: %LINK-3-UPDOWN: Interface GigabitEthernet0/1, changed state to down
    *Oct 28 20:52:42.195: %LINK-3-UPDOWN: Interface GigabitEthernet0/2, changed state to down
    *Oct 28 20:52:44.631: %LINK-3-UPDOWN: Interface SM1/1, changed state to up
    *Oct 28 20:53:01.655: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/0, changed state to up
    *Oct 28 20:53:01.923: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/1, changed state to up
    *Oct 28 20:53:02.075: %LINK-3-UPDOWN: Interface Foreign Exchange Station 0/1/0, changed state to up
    *Oct 28 20:53:02.075: %LINK-3-UPDOWN: Interface Foreign Exchange Station 0/1/1, changed state to up
    *Oct 28 20:53:43.739: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/0, changed state to operational status down due to cable removal
    *Oct 28 20:53:44.739: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/1, changed state to operational status down due to cable removal
    Queued messages:
    No warm reboot Storage
    *** System received a Bus Error exception ***
    signal= 0xa, code= 0x40c, context= 0x29726b74
    PC = 0x22768478, SP = 0x3022fbb8, RA = 0x22768424
    Cause Reg = 0x0000040c, Status Reg = 0x500099e3
    System Bootstrap, Version 15.0(1r)M6, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 2010 by cisco Systems, Inc.
    Total memory size = 512 MB - On-board = 512 MB, DIMM0 = 0 MB
    CISCO2911/K9 platform with 524288 Kbytes of main memory
    Main memory is configured to 72/-1(On-board/DIMM0) bit mode with ECC enabled

    Readonly ROMMON initialized
    program load complete, entry point: 0x80803000, size: 0x1b340

    IOS Image Load Test
    ___________________
    Digitally Signed Development Software
    program load complete, entry point: 0x81000000, size: 0x40b6b74
    Self decompressing the image : #############################################################################################################

    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2691036>
    or simply reply to this email.
    -- --
    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2691978>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2699015>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2699042>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2699089>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2699640>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2704890>
    or simply reply to this email.

    Subject: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-
    Replied by: Ken Romo on 20-11-2010 01:34:37 AM
    Radhika,
     
    So what is the root cause?
     
    The IOS or the PVDMS?
     
    Do I need to RMA my PVDMS?
     
    Let me know thank you.
     
    Ken
     
    Ken,

    Thanks for the information. We will check internally if this has been tested. I will cancel the debug session for today since we most likely have the root cause for the issue. We will try to reproduce this internally and if we need further information from you will setup a different session.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Tuesday, November 02, 2010 8:49 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    The PVDMS is:

    PVDM3-16 V01
    S/N FOC14200FNK

    Is this what you were looking for?

    Ken


    Ken,

    I am not sure if it is the PVDM that is bad but it could be a bug in the IOS image also where you have pvdm and the SRE module it could be some issue. For now can you continute to do beta for SRE-v without the PVDMS.



    I will check with the team and get back to you as to how to proceed.



    Can you let me know what PVDM models you have so we can try to reproduce this in our lab.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Monday, November 01, 2010 3:59 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    I pulled the PVDM and it is working.

    Does this mean the PVDM is bad?

    Ken


    Ken,

    Please try out the new image sent by Brett to you when you get a chance. Also one difference we noticed is that you have PVDM¿s in your setup that we don not have in our test setup. Would it be possible to remove the PVDMS temporarily and try the ping? This may help us root cause the issue.



    I will also schedule a WebEx for tomorrow morning 10:30 PST with the IOS developer so we can take a look if the change of IOS image and removal of PVDM¿s does not solve the issue. Please let me know if that time slot does not work for you.



    Thanks,

    Radhika





    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Monday, November 01, 2010 11:19 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    Here you go:

    boxer#show vlan-switch
    VLAN Name Status Ports
    ---- -------------------------------- --------- -------------------------------
    1 default active
    1002 fddi-default act/unsup
    1003 token-ring-default act/unsup
    1004 fddinet-default act/unsup
    1005 trnet-default act/unsup
    VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2
    ---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------
    1 enet 100001 1500 - - - - - 1002 1003
    1002 fddi 101002 1500 - - - - - 1 1003
    1003 tr 101003 1500 1005 0 - - srb 1 1002
    1004 fdnet 101004 1500 - - 1 ibm - 0 0
    1005 trnet 101005 1500 - - 1 ibm - 0 0


    boxer#sh platform mgf module
    Registered Module Information
    Code: NR - Not Registered, TM - Trust Mode, SP - Scheduling Profile
    BL - Buffer Level, TR - Traffic Rate, PT - Pause Threshold
    slot vlan type/ID TM SP BL TR PT
    ---- ---- ---------- ------- --- ------ ----- ----
    ISM NR
    EHWIC-0 NR
    EHWIC-1 NR
    EHWIC-2 NR
    EHWIC-3 NR
    PVDM-0 2 PVDM/5 UP 1 low 1000 low
    PVDM-1 2 PVDM/5 UP 1 low 1000 low
    SM-1 1 Switch/3 UP 1 low 1000 high




    Thanks Ken. Can you also give us the output of the following.



    1) show vlan-switch

    2) ¿show platform mgf module¿ before the crash happens.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Monday, November 01, 2010 10:50 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    I will try whatever you suggest, just let me know when you have posted the new IOS.

    Below is my config:

    boxer#sh run
    Building configuration...

    Current configuration : 5777 bytes
    !
    version 15.1
    service timestamps debug datetime msec
    service timestamps log datetime msec
    no service password-encryption
    !
    hostname boxer
    !
    boot-start-marker
    boot system flash0 c2900-universalk9-mz.SSA.151-2.19.T
    boot-end-marker
    !
    !
    logging buffered 51200 warnings
    !
    no aaa new-model
    !
    no ipv6 cef
    ip source-route
    ip cef
    !
    !
    !
    !
    !
    ip domain name yourdomain.com
    multilink bundle-name authenticated
    !
    !
    !
    !
    !
    crypto pki token default removal timeout 0
    !
    crypto pki trustpoint TP-self-signed-1999750280
    enrollment selfsigned
    subject-name cn=IOS-Self-Signed-Certificate-1999750280
    revocation-check none
    rsakeypair TP-self-signed-1999750280
    !
    !
    crypto pki certificate chain TP-self-signed-1999750280
    certificate self-signed 01
    3082024C 308201B5 A0030201 02020101 300D0609 2A864886 F70D0101 04050030
    31312F30 2D060355 04031326 494F532D 53656C66 2D536967 6E65642D 43657274
    69666963 6174652D 31393939 37353032 3830301E 170D3130 31303230 32323335
    32365A17 0D323030 31303130 30303030 305A3031 312F302D 06035504 03132649
    4F532D53 656C662D 5369676E 65642D43 65727469 66696361 74652D31 39393937
    35303238 3030819F 300D0609 2A864886 F70D0101 01050003 818D0030 81890281
    81009378 2E139D79 DCA59865 14AB3398 870362B7 40BB9C13 A5DC5315 6108DF92
    5E78CF06 A40D4DB5 B66D410E FAFE75AC 764997B1 5C551A47 CFA00109 520352EC
    33A69E24 B3C1175B 136FC62A 8BE4637E B834059B FC7CAA6E 957DA0BB 66D8DC49
    80F82890 981FFCFE 0DC7E6F9 53287989 3887C5F6 AF59D0BE B502E11E FD16F556
    DBB90203 010001A3 74307230 0F060355 1D130101 FF040530 030101FF 301F0603
    551D1104 18301682 14626F78 65722E79 6F757264 6F6D6169 6E2E636F 6D301F06
    03551D23 04183016 80143541 7934E424 4B9A60DB E6C908C3 C20BAA17 D058301D
    0603551D 0E041604 14354179 34E4244B 9A60DBE6 C908C3C2 0BAA17D0 58300D06
    092A8648 86F70D01 01040500 03818100 3D222AB5 177D452F 153DCA26 1D7ECB49
    58BCBF60 DA18DC04 94B82EA3 76884EBC D7131641 08687C04 6C6645DF 78B2D2F8
    409BCAD7 50AF5091 B99614FD C2424D89 407A9109 BCA20473 F4CE33D4 4B126483
    C240C0B9 7A628E53 E419FEC3 B8853671 03113F5E 47FA8120 9F9A7A9D 11498FE0
    82C96578 8FD9770A EBD27F73 DF2E1487
    quit
    voice-card 0
    !
    !
    !
    !
    !
    !
    !
    license udi pid CISCO2911/K9 sn FTX1422A077
    hw-module pvdm 0/0
    !
    hw-module sm 1
    !
    !
    !
    username jack privilege 15 secret 5 $1$c5QR$fYGTbhWRKsBZ1JpNyIQGG1
    username marco privilege 15 secret 5 $1$amqq$5pI0T7mUViDL5Y.NqX/yz.
    !
    redundancy
    !
    !
    !
    !
    !
    !
    interface GigabitEthernet0/0
    description To tusqa network
    ip address 172.17.17.130 255.255.248.0
    duplex auto
    speed auto
    !
    interface GigabitEthernet0/1
    no ip address
    shutdown
    duplex auto
    speed auto
    !
    interface GigabitEthernet0/2
    no ip address
    shutdown
    duplex auto
    speed auto
    !
    interface SM1/0
    ip unnumbered GigabitEthernet0/0
    service-module ip address 172.17.17.129 255.255.248.0
    !Application: SRE-V Running on SMV
    service-module ip default-gateway 172.17.17.130
    service-module mgf ip address 10.62.64.1 255.255.255.0
    service-module mgf ip default-gateway 10.62.64.2
    !
    interface SM1/1
    description Internal switch interface connected to Service Module
    switchport mode trunk
    !
    interface Vlan1
    ip address 10.62.64.2 255.255.255.0
    !
    ip forward-protocol nd
    !
    ip http server
    ip http access-class 23
    ip http authentication local
    ip http secure-server
    ip http timeout-policy idle 60 life 86400 requests 10000
    !
    ip route 172.17.17.129 255.255.255.255 SM1/0
    !
    !
    !
    !
    control-plane
    !
    !
    voice-port 0/0/0
    !
    voice-port 0/0/1
    !
    voice-port 0/1/0
    !
    voice-port 0/1/1
    !
    !
    !
    mgcp profile default
    !
    !
    !
    !
    !
    gatekeeper
    shutdown
    !
    !
    banner exec ^C
    % Password expiration warning.
    -----------------------------------------------------------------------
    Cisco Configuration Professional (Cisco CP) is installed on this device
    and it provides the default username "cisco" for one-time use. If you have
    already used the username "cisco" to login to the router and your IOS image
    supports the "one-time" user option, then this username has already expired.
    You will not be able to login to the router with this username after you exit
    this session.
    It is strongly suggested that you create a new username with a privilege level
    of 15 using the following command.
    username <myuser> privilege 15 secret 0 <mypassword>
    Replace <myuser> and <mypassword> with the username and password you want to
    use.
    -----------------------------------------------------------------------
    ^C
    banner login ^C
    -----------------------------------------------------------------------
    Cisco Configuration Professional (Cisco CP) is installed on this device.
    This feature requires the one-time use of the username "cisco" with the
    password "cisco". These default credentials have a privilege level of 15.
    YOU MUST USE CISCO CP or the CISCO IOS CLI TO CHANGE THESE PUBLICLY-KNOWN
    CREDENTIALS
    Here are the Cisco IOS commands.
    username <myuser> privilege 15 secret 0 <mypassword>
    no username cisco
    Replace <myuser> and <mypassword> with the username and password you want
    to use.
    IF YOU DO NOT CHANGE THE PUBLICLY-KNOWN CREDENTIALS, YOU WILL NOT BE ABLE
    TO LOG INTO THE DEVICE AGAIN AFTER YOU HAVE LOGGED OFF.
    For more information about Cisco CP please follow the instructions in the
    QUICK START GUIDE for your router or go to http://www.cisco.com/go/ciscocp
    -----------------------------------------------------------------------
    ^C
    !
    line con 0
    login local
    line aux 0
    line 67
    no activation-character
    no exec
    transport preferred none
    transport input all
    transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
    stopbits 1
    flowcontrol software
    line vty 0 4
    privilege level 15
    login local
    transport input telnet
    line vty 5 15
    privilege level 15
    login local
    transport input telnet ssh
    !
    exception data-corruption buffer truncate
    scheduler allocate 20000 1000
    end



    Ken, Thanks for trying out the image for us. We are trying to reproduce this on our end but have had no luck so far. Can you please send us the output of show running-config from your router.



    Also we have one more image that we would like you to try it out before the debusg session would that be ok?



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Monday, November 01, 2010 10:22 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------

    Radhika,

    I tried the new OS and still getting same IOS crash.
    As mentioned I will work around your schedule so let me if you were able to get someone from the IOS team to help troubleshoot today.

    Thanks in advance,

    Ken Romo


    Ken,

    I am trying to get some help from the IOS team since this a router crash. So I will setup the webex session to debug for some time Monday so we can collect all the information and try out any suggestion from them.



    For Now We will post a newer IOS image to the beta Site and can you give that a try to see if that will solve the issue.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Friday, October 29, 2010 8:24 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    I will work around your schedule, anytime you are available, I will make myself available.
    email:
    kromo@opentext.com

    Thanks in advance,

    Ken Romo

    +++++++++++++++++++++++++++++++++

    Ken,

    Would a webex session tomorrow morning (any time between 10:00 and 1:00) work for you? Let me know the time that would work for you and also your email address so I can send you a webex invite.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Thursday, October 28, 2010 3:12 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Radhika Miriyala in Service Ready Engine Virtualizatio



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    No worries, we are trying to work this out together and I appreciate the help.
    s/m 1/1 is set as trunk but I went ahead and reconfigured to truank again and reloaded OS and get the same crash when I ping to the MGF interface from the SRE (I attached the errors at the bottom of this message).

    Ken,

    Sorry I just realized the mistake. I meant to say make the interface sm 1/1 as trunk.

    Sorry about the confusion.



    Please try it out.



    Thanks,

    Radhika



    boxer#
    %ALIGN-1-FATAL: Illegal access to a low address 22:02:10 UTC Thu Oct 28 2010
    addr=0x14, pc=0x22765BD8z , ra=0x22765B84z , sp=0x3022FBB8
    %ALIGN-1-FATAL: Illegal access to a low address 22:02:11 UTC Thu Oct 28 2010
    addr=0x14, pc=0x22765BD8z , ra=0x22765B84z , sp=0x3022FBB8

    22:02:11 UTC Thu Oct 28 2010: TLB (store) exception, CPU signal 10, PC = 0x22768478

    --------------------------------------------------------------------
    Possible software fault. Upon reccurence, please collect
    crashinfo, "show tech" and contact Cisco Technical Support.
    --------------------------------------------------------------------

    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z
    $0 : 00000000 00000000, AT : 00000000 29130000, v0 : 00000000 00000001, v1 : 00000000 0D8B8540
    a0 : 00000000 00000000, a1 : 00000000 0D8B8584, a2 : 00000000 2A2F8ABC, a3 : 00000000 00000004
    t0 : 00000000 00000020, t1 : 00000000 500099E1, t2 : 00000000 500081E0, t3 : FFFFFFFF FFFFFFF2
    t4 : 00000000 0000000E, t5 : 00000000 00000000, t6 : 00000000 0D95F890, t7 : 00000000 000001FF
    s0 : 00000000 00000000, s1 : 00000000 2A2FDB40, s2 : FFFFFFFF FFFFFFEC, s3 : 00000000 3080C980
    s4 : 00000000 0D95F89E, s5 : 00000000 2A300EE0, s6 : 00000000 00000000, s7 : 00000000 0000000E
    t8 : 00000000 000007FC, t9 : 00000000 2A300200, k0 : 00000000 00000000, k1 : 00000000 00000000
    gp : 00000000 29133C00, sp : 00000000 3022FBB8, s8 : 00000000 00000054, ra : 00000000 22768424
    EPC : 22768478, ErrorEPC : 80412AB4, SREG : 500099E3
    MDLO : 87126668, MDHI : D990ADBB, BadVaddr : 00000014
    CacheErr_Icache : 0x007F7F00 - 000040D8, CacheErr_Dcache : 0x00000000 - 00001FA0
    TagLo_Icache : 0x00000000 - 23642303, DataLo_Icache : 0xAFBF0018 - 0D81ADDB
    DataHi_Icache: 0x00000000 - 00000001
    TagLo_Dcache : 0x00000000 - 2277E583, TagHi_Dcache : 0x00000000 - 0912BD81
    DataLo_Dcache: 0x00000001 - 2368110C, DataHi_Dcache : 0x00000000 - 0000001C
    TEXT_START : 0x21003178
    DATA_START : 0x260888A0
    Cause 0000040C (Code 0x3): TLB (store) exception

    22:02:11 UTC Thu Oct 28 2010: TLB (store) exception, CPU signal 10, PC = 0x22768478

    --------------------------------------------------------------------
    Possible software fault. Upon reccurence, please collect
    crashinfo, "show tech" and contact Cisco Technical Support.
    --------------------------------------------------------------------

    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z
    $0 : 00000000 00000000, AT : 00000000 29130000, v0 : 00000000 00000001, v1 : 00000000 0D8B8540
    a0 : 00000000 00000000, a1 : 00000000 0D8B8584, a2 : 00000000 2A2F8ABC, a3 : 00000000 00000004
    t0 : 00000000 00000020, t1 : 00000000 500099E1, t2 : 00000000 500081E0, t3 : FFFFFFFF FFFFFFF2
    t4 : 00000000 0000000E, t5 : 00000000 00000000, t6 : 00000000 0D95F890, t7 : 00000000 000001FF
    s0 : 00000000 00000000, s1 : 00000000 2A2FDB40, s2 : FFFFFFFF FFFFFFEC, s3 : 00000000 3080C980
    s4 : 00000000 0D95F89E, s5 : 00000000 2A300EE0, s6 : 00000000 00000000, s7 : 00000000 0000000E
    t8 : 00000000 000007FC, t9 : 00000000 2A300200, k0 : 00000000 00000000, k1 : 00000000 00000000
    gp : 00000000 29133C00, sp : 00000000 3022FBB8, s8 : 00000000 00000054, ra : 00000000 22768424
    EPC : 22768478, ErrorEPC : 80412AB4, SREG : 500099E3
    MDLO : 87126668, MDHI : D990ADBB, BadVaddr : 00000014
    CacheErr_Icache : 0x007F7F00 - 000040D8, CacheErr_Dcache : 0x00000000 - 00001FA0
    TagLo_Icache : 0x00000000 - 23642303, DataLo_Icache : 0xAFBF0018 - 0D81ADDB
    DataHi_Icache: 0x00000000 - 00000001
    TagLo_Dcache : 0x00000000 - 2277E583, TagHi_Dcache : 0x00000000 - 0912BD81
    DataLo_Dcache: 0x00000001 - 2368110C, DataHi_Dcache : 0x00000000 - 0000001C
    TEXT_START : 0x21003178
    DATA_START : 0x260888A0
    Cause 0000040C (Code 0x3): TLB (store) exception
    Writing crashinfo to flash:crashinfo_20101028-220211-UTC
    22:02:11 UTC Thu Oct 28 2010: TLB (store) exception, CPU signal 10, PC = 0x22768478

    --------------------------------------------------------------------
    Possible software fault. Upon reccurence, please collect
    crashinfo, "show tech" and contact Cisco Technical Support.
    --------------------------------------------------------------------

    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z
    $0 : 00000000 00000000, AT : 00000000 29130000, v0 : 00000000 00000001, v1 : 00000000 0D8B8540
    a0 : 00000000 00000000, a1 : 00000000 0D8B8584, a2 : 00000000 2A2F8ABC, a3 : 00000000 00000004
    t0 : 00000000 00000020, t1 : 00000000 500099E1, t2 : 00000000 500081E0, t3 : FFFFFFFF FFFFFFF2
    t4 : 00000000 0000000E, t5 : 00000000 00000000, t6 : 00000000 0D95F890, t7 : 00000000 000001FF
    s0 : 00000000 00000000, s1 : 00000000 2A2FDB40, s2 : FFFFFFFF FFFFFFEC, s3 : 00000000 3080C980
    s4 : 00000000 0D95F89E, s5 : 00000000 2A300EE0, s6 : 00000000 00000000, s7 : 00000000 0000000E
    t8 : 00000000 000007FC, t9 : 00000000 2A300200, k0 : 00000000 00000000, k1 : 00000000 00000000
    gp : 00000000 29133C00, sp : 00000000 3022FBB8, s8 : 00000000 00000054, ra : 00000000 22768424
    EPC : 22768478, ErrorEPC : 80412AB4, SREG : 500099E3
    MDLO : 87126668, MDHI : D990ADBB, BadVaddr : 00000014
    CacheErr_Icache : 0x007F7F00 - 000040D8, CacheErr_Dcache : 0x00000000 - 00001FA0
    TagLo_Icache : 0x00000000 - 23642303, DataLo_Icache : 0xAFBF0018 - 0D81ADDB
    DataHi_Icache: 0x00000000 - 00000001
    TagLo_Dcache : 0x00000000 - 2277E583, TagHi_Dcache : 0x00000000 - 0912BD81
    DataLo_Dcache: 0x00000001 - 2368110C, DataHi_Dcache : 0x00000000 - 0000001C
    TEXT_START : 0x21003178
    DATA_START : 0x260888A0
    Cause 0000040C (Code 0x3): TLB (store) exception
    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z

    === Flushing messages (22:02:12 UTC Thu Oct 28 2010) ===
    Buffered messages:
    *Oct 28 20:52:40.075: %LINK-3-UPDOWN: Interface SM1/0, changed state to up
    *Oct 28 20:52:42.195: %LINK-3-UPDOWN: Interface GigabitEthernet0/0, changed state to up
    *Oct 28 20:52:42.195: %LINK-3-UPDOWN: Interface GigabitEthernet0/1, changed state to down
    *Oct 28 20:52:42.195: %LINK-3-UPDOWN: Interface GigabitEthernet0/2, changed state to down
    *Oct 28 20:52:44.631: %LINK-3-UPDOWN: Interface SM1/1, changed state to up
    *Oct 28 20:53:01.655: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/0, changed state to up
    *Oct 28 20:53:01.923: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/1, changed state to up
    *Oct 28 20:53:02.075: %LINK-3-UPDOWN: Interface Foreign Exchange Station 0/1/0, changed state to up
    *Oct 28 20:53:02.075: %LINK-3-UPDOWN: Interface Foreign Exchange Station 0/1/1, changed state to up
    *Oct 28 20:53:43.739: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/0, changed state to operational status down due to cable removal
    *Oct 28 20:53:44.739: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/1, changed state to operational status down due to cable removal
    Queued messages:
    No warm reboot Storage
    *** System received a Bus Error exception ***
    signal= 0xa, code= 0x40c, context= 0x29726b74
    PC = 0x22768478, SP = 0x3022fbb8, RA = 0x22768424
    Cause Reg = 0x0000040c, Status Reg = 0x500099e3
    System Bootstrap, Version 15.0(1r)M6, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 2010 by cisco Systems, Inc.
    Total memory size = 512 MB - On-board = 512 MB, DIMM0 = 0 MB
    CISCO2911/K9 platform with 524288 Kbytes of main memory
    Main memory is configured to 72/-1(On-board/DIMM0) bit mode with ECC enabled

    Readonly ROMMON initialized
    program load complete, entry point: 0x80803000, size: 0x1b340

    IOS Image Load Test
    ___________________
    Digitally Signed Development Software
    program load complete, entry point: 0x81000000, size: 0x40b6b74
    Self decompressing the image : #############################################################################################################

    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2691036>
    or simply reply to this email.
    -- --
    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2691978>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2699015>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2699042>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2699089>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2699640>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2704890>
    or simply reply to this email.


    Subject: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-
    Replied by: Radhika Miriyala on 20-11-2010 01:34:37 AM
    Ken,

    Right now it looks an IOS bug but we need to reproduce this in house so we can confirm for sure. I will keep you in the loop on what we find. If it turns out to be an issue with this particular PVDM I will let you know.



    Appreciate all your help with this.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Tuesday, November 02, 2010 9:51 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    So what is the root cause?

    The IOS or the PVDMS?

    Do I need to RMA my PVDMS?

    Let me know thank you.

    Ken


    Ken,

    Thanks for the information. We will check internally if this has been tested. I will cancel the debug session for today since we most likely have the root cause for the issue. We will try to reproduce this internally and if we need further information from you will setup a different session.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Tuesday, November 02, 2010 8:49 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    The PVDMS is:

    PVDM3-16 V01
    S/N FOC14200FNK

    Is this what you were looking for?

    Ken


    Ken,

    I am not sure if it is the PVDM that is bad but it could be a bug in the IOS image also where you have pvdm and the SRE module it could be some issue. For now can you continute to do beta for SRE-v without the PVDMS.



    I will check with the team and get back to you as to how to proceed.



    Can you let me know what PVDM models you have so we can try to reproduce this in our lab.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Monday, November 01, 2010 3:59 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    I pulled the PVDM and it is working.

    Does this mean the PVDM is bad?

    Ken


    Ken,

    Please try out the new image sent by Brett to you when you get a chance. Also one difference we noticed is that you have PVDM¿s in your setup that we don not have in our test setup. Would it be possible to remove the PVDMS temporarily and try the ping? This may help us root cause the issue.



    I will also schedule a WebEx for tomorrow morning 10:30 PST with the IOS developer so we can take a look if the change of IOS image and removal of PVDM¿s does not solve the issue. Please let me know if that time slot does not work for you.



    Thanks,

    Radhika





    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Monday, November 01, 2010 11:19 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    Here you go:

    boxer#show vlan-switch
    VLAN Name Status Ports
    ---- -------------------------------- --------- -------------------------------
    1 default active
    1002 fddi-default act/unsup
    1003 token-ring-default act/unsup
    1004 fddinet-default act/unsup
    1005 trnet-default act/unsup
    VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2
    ---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------
    1 enet 100001 1500 - - - - - 1002 1003
    1002 fddi 101002 1500 - - - - - 1 1003
    1003 tr 101003 1500 1005 0 - - srb 1 1002
    1004 fdnet 101004 1500 - - 1 ibm - 0 0
    1005 trnet 101005 1500 - - 1 ibm - 0 0


    boxer#sh platform mgf module
    Registered Module Information
    Code: NR - Not Registered, TM - Trust Mode, SP - Scheduling Profile
    BL - Buffer Level, TR - Traffic Rate, PT - Pause Threshold
    slot vlan type/ID TM SP BL TR PT
    ---- ---- ---------- ------- --- ------ ----- ----
    ISM NR
    EHWIC-0 NR
    EHWIC-1 NR
    EHWIC-2 NR
    EHWIC-3 NR
    PVDM-0 2 PVDM/5 UP 1 low 1000 low
    PVDM-1 2 PVDM/5 UP 1 low 1000 low
    SM-1 1 Switch/3 UP 1 low 1000 high




    Thanks Ken. Can you also give us the output of the following.



    1) show vlan-switch

    2) ¿show platform mgf module¿ before the crash happens.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Monday, November 01, 2010 10:50 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    I will try whatever you suggest, just let me know when you have posted the new IOS.

    Below is my config:

    boxer#sh run
    Building configuration...

    Current configuration : 5777 bytes
    !
    version 15.1
    service timestamps debug datetime msec
    service timestamps log datetime msec
    no service password-encryption
    !
    hostname boxer
    !
    boot-start-marker
    boot system flash0 c2900-universalk9-mz.SSA.151-2.19.T
    boot-end-marker
    !
    !
    logging buffered 51200 warnings
    !
    no aaa new-model
    !
    no ipv6 cef
    ip source-route
    ip cef
    !
    !
    !
    !
    !
    ip domain name yourdomain.com
    multilink bundle-name authenticated
    !
    !
    !
    !
    !
    crypto pki token default removal timeout 0
    !
    crypto pki trustpoint TP-self-signed-1999750280
    enrollment selfsigned
    subject-name cn=IOS-Self-Signed-Certificate-1999750280
    revocation-check none
    rsakeypair TP-self-signed-1999750280
    !
    !
    crypto pki certificate chain TP-self-signed-1999750280
    certificate self-signed 01
    3082024C 308201B5 A0030201 02020101 300D0609 2A864886 F70D0101 04050030
    31312F30 2D060355 04031326 494F532D 53656C66 2D536967 6E65642D 43657274
    69666963 6174652D 31393939 37353032 3830301E 170D3130 31303230 32323335
    32365A17 0D323030 31303130 30303030 305A3031 312F302D 06035504 03132649
    4F532D53 656C662D 5369676E 65642D43 65727469 66696361 74652D31 39393937
    35303238 3030819F 300D0609 2A864886 F70D0101 01050003 818D0030 81890281
    81009378 2E139D79 DCA59865 14AB3398 870362B7 40BB9C13 A5DC5315 6108DF92
    5E78CF06 A40D4DB5 B66D410E FAFE75AC 764997B1 5C551A47 CFA00109 520352EC
    33A69E24 B3C1175B 136FC62A 8BE4637E B834059B FC7CAA6E 957DA0BB 66D8DC49
    80F82890 981FFCFE 0DC7E6F9 53287989 3887C5F6 AF59D0BE B502E11E FD16F556
    DBB90203 010001A3 74307230 0F060355 1D130101 FF040530 030101FF 301F0603
    551D1104 18301682 14626F78 65722E79 6F757264 6F6D6169 6E2E636F 6D301F06
    03551D23 04183016 80143541 7934E424 4B9A60DB E6C908C3 C20BAA17 D058301D
    0603551D 0E041604 14354179 34E4244B 9A60DBE6 C908C3C2 0BAA17D0 58300D06
    092A8648 86F70D01 01040500 03818100 3D222AB5 177D452F 153DCA26 1D7ECB49
    58BCBF60 DA18DC04 94B82EA3 76884EBC D7131641 08687C04 6C6645DF 78B2D2F8
    409BCAD7 50AF5091 B99614FD C2424D89 407A9109 BCA20473 F4CE33D4 4B126483
    C240C0B9 7A628E53 E419FEC3 B8853671 03113F5E 47FA8120 9F9A7A9D 11498FE0
    82C96578 8FD9770A EBD27F73 DF2E1487
    quit
    voice-card 0
    !
    !
    !
    !
    !
    !
    !
    license udi pid CISCO2911/K9 sn FTX1422A077
    hw-module pvdm 0/0
    !
    hw-module sm 1
    !
    !
    !
    username jack privilege 15 secret 5 $1$c5QR$fYGTbhWRKsBZ1JpNyIQGG1
    username marco privilege 15 secret 5 $1$amqq$5pI0T7mUViDL5Y.NqX/yz.
    !
    redundancy
    !
    !
    !
    !
    !
    !
    interface GigabitEthernet0/0
    description To tusqa network
    ip address 172.17.17.130 255.255.248.0
    duplex auto
    speed auto
    !
    interface GigabitEthernet0/1
    no ip address
    shutdown
    duplex auto
    speed auto
    !
    interface GigabitEthernet0/2
    no ip address
    shutdown
    duplex auto
    speed auto
    !
    interface SM1/0
    ip unnumbered GigabitEthernet0/0
    service-module ip address 172.17.17.129 255.255.248.0
    !Application: SRE-V Running on SMV
    service-module ip default-gateway 172.17.17.130
    service-module mgf ip address 10.62.64.1 255.255.255.0
    service-module mgf ip default-gateway 10.62.64.2
    !
    interface SM1/1
    description Internal switch interface connected to Service Module
    switchport mode trunk
    !
    interface Vlan1
    ip address 10.62.64.2 255.255.255.0
    !
    ip forward-protocol nd
    !
    ip http server
    ip http access-class 23
    ip http authentication local
    ip http secure-server
    ip http timeout-policy idle 60 life 86400 requests 10000
    !
    ip route 172.17.17.129 255.255.255.255 SM1/0
    !
    !
    !
    !
    control-plane
    !
    !
    voice-port 0/0/0
    !
    voice-port 0/0/1
    !
    voice-port 0/1/0
    !
    voice-port 0/1/1
    !
    !
    !
    mgcp profile default
    !
    !
    !
    !
    !
    gatekeeper
    shutdown
    !
    !
    banner exec ^C
    % Password expiration warning.
    -----------------------------------------------------------------------
    Cisco Configuration Professional (Cisco CP) is installed on this device
    and it provides the default username "cisco" for one-time use. If you have
    already used the username "cisco" to login to the router and your IOS image
    supports the "one-time" user option, then this username has already expired.
    You will not be able to login to the router with this username after you exit
    this session.
    It is strongly suggested that you create a new username with a privilege level
    of 15 using the following command.
    username <myuser> privilege 15 secret 0 <mypassword>
    Replace <myuser> and <mypassword> with the username and password you want to
    use.
    -----------------------------------------------------------------------
    ^C
    banner login ^C
    -----------------------------------------------------------------------
    Cisco Configuration Professional (Cisco CP) is installed on this device.
    This feature requires the one-time use of the username "cisco" with the
    password "cisco". These default credentials have a privilege level of 15.
    YOU MUST USE CISCO CP or the CISCO IOS CLI TO CHANGE THESE PUBLICLY-KNOWN
    CREDENTIALS
    Here are the Cisco IOS commands.
    username <myuser> privilege 15 secret 0 <mypassword>
    no username cisco
    Replace <myuser> and <mypassword> with the username and password you want
    to use.
    IF YOU DO NOT CHANGE THE PUBLICLY-KNOWN CREDENTIALS, YOU WILL NOT BE ABLE
    TO LOG INTO THE DEVICE AGAIN AFTER YOU HAVE LOGGED OFF.
    For more information about Cisco CP please follow the instructions in the
    QUICK START GUIDE for your router or go to http://www.cisco.com/go/ciscocp
    -----------------------------------------------------------------------
    ^C
    !
    line con 0
    login local
    line aux 0
    line 67
    no activation-character
    no exec
    transport preferred none
    transport input all
    transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
    stopbits 1
    flowcontrol software
    line vty 0 4
    privilege level 15
    login local
    transport input telnet
    line vty 5 15
    privilege level 15
    login local
    transport input telnet ssh
    !
    exception data-corruption buffer truncate
    scheduler allocate 20000 1000
    end



    Ken, Thanks for trying out the image for us. We are trying to reproduce this on our end but have had no luck so far. Can you please send us the output of show running-config from your router.



    Also we have one more image that we would like you to try it out before the debusg session would that be ok?



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Monday, November 01, 2010 10:22 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------

    Radhika,

    I tried the new OS and still getting same IOS crash.
    As mentioned I will work around your schedule so let me if you were able to get someone from the IOS team to help troubleshoot today.

    Thanks in advance,

    Ken Romo


    Ken,

    I am trying to get some help from the IOS team since this a router crash. So I will setup the webex session to debug for some time Monday so we can collect all the information and try out any suggestion from them.



    For Now We will post a newer IOS image to the beta Site and can you give that a try to see if that will solve the issue.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Friday, October 29, 2010 8:24 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    I will work around your schedule, anytime you are available, I will make myself available.
    email:
    kromo@opentext.com

    Thanks in advance,

    Ken Romo

    +++++++++++++++++++++++++++++++++

    Ken,

    Would a webex session tomorrow morning (any time between 10:00 and 1:00) work for you? Let me know the time that would work for you and also your email address so I can send you a webex invite.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Thursday, October 28, 2010 3:12 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Radhika Miriyala in Service Ready Engine Virtualizatio



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    No worries, we are trying to work this out together and I appreciate the help.
    s/m 1/1 is set as trunk but I went ahead and reconfigured to truank again and reloaded OS and get the same crash when I ping to the MGF interface from the SRE (I attached the errors at the bottom of this message).

    Ken,

    Sorry I just realized the mistake. I meant to say make the interface sm 1/1 as trunk.

    Sorry about the confusion.



    Please try it out.



    Thanks,

    Radhika



    boxer#
    %ALIGN-1-FATAL: Illegal access to a low address 22:02:10 UTC Thu Oct 28 2010
    addr=0x14, pc=0x22765BD8z , ra=0x22765B84z , sp=0x3022FBB8
    %ALIGN-1-FATAL: Illegal access to a low address 22:02:11 UTC Thu Oct 28 2010
    addr=0x14, pc=0x22765BD8z , ra=0x22765B84z , sp=0x3022FBB8

    22:02:11 UTC Thu Oct 28 2010: TLB (store) exception, CPU signal 10, PC = 0x22768478

    --------------------------------------------------------------------
    Possible software fault. Upon reccurence, please collect
    crashinfo, "show tech" and contact Cisco Technical Support.
    --------------------------------------------------------------------

    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z
    $0 : 00000000 00000000, AT : 00000000 29130000, v0 : 00000000 00000001, v1 : 00000000 0D8B8540
    a0 : 00000000 00000000, a1 : 00000000 0D8B8584, a2 : 00000000 2A2F8ABC, a3 : 00000000 00000004
    t0 : 00000000 00000020, t1 : 00000000 500099E1, t2 : 00000000 500081E0, t3 : FFFFFFFF FFFFFFF2
    t4 : 00000000 0000000E, t5 : 00000000 00000000, t6 : 00000000 0D95F890, t7 : 00000000 000001FF
    s0 : 00000000 00000000, s1 : 00000000 2A2FDB40, s2 : FFFFFFFF FFFFFFEC, s3 : 00000000 3080C980
    s4 : 00000000 0D95F89E, s5 : 00000000 2A300EE0, s6 : 00000000 00000000, s7 : 00000000 0000000E
    t8 : 00000000 000007FC, t9 : 00000000 2A300200, k0 : 00000000 00000000, k1 : 00000000 00000000
    gp : 00000000 29133C00, sp : 00000000 3022FBB8, s8 : 00000000 00000054, ra : 00000000 22768424
    EPC : 22768478, ErrorEPC : 80412AB4, SREG : 500099E3
    MDLO : 87126668, MDHI : D990ADBB, BadVaddr : 00000014
    CacheErr_Icache : 0x007F7F00 - 000040D8, CacheErr_Dcache : 0x00000000 - 00001FA0
    TagLo_Icache : 0x00000000 - 23642303, DataLo_Icache : 0xAFBF0018 - 0D81ADDB
    DataHi_Icache: 0x00000000 - 00000001
    TagLo_Dcache : 0x00000000 - 2277E583, TagHi_Dcache : 0x00000000 - 0912BD81
    DataLo_Dcache: 0x00000001 - 2368110C, DataHi_Dcache : 0x00000000 - 0000001C
    TEXT_START : 0x21003178
    DATA_START : 0x260888A0
    Cause 0000040C (Code 0x3): TLB (store) exception

    22:02:11 UTC Thu Oct 28 2010: TLB (store) exception, CPU signal 10, PC = 0x22768478

    --------------------------------------------------------------------
    Possible software fault. Upon reccurence, please collect
    crashinfo, "show tech" and contact Cisco Technical Support.
    --------------------------------------------------------------------

    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z
    $0 : 00000000 00000000, AT : 00000000 29130000, v0 : 00000000 00000001, v1 : 00000000 0D8B8540
    a0 : 00000000 00000000, a1 : 00000000 0D8B8584, a2 : 00000000 2A2F8ABC, a3 : 00000000 00000004
    t0 : 00000000 00000020, t1 : 00000000 500099E1, t2 : 00000000 500081E0, t3 : FFFFFFFF FFFFFFF2
    t4 : 00000000 0000000E, t5 : 00000000 00000000, t6 : 00000000 0D95F890, t7 : 00000000 000001FF
    s0 : 00000000 00000000, s1 : 00000000 2A2FDB40, s2 : FFFFFFFF FFFFFFEC, s3 : 00000000 3080C980
    s4 : 00000000 0D95F89E, s5 : 00000000 2A300EE0, s6 : 00000000 00000000, s7 : 00000000 0000000E
    t8 : 00000000 000007FC, t9 : 00000000 2A300200, k0 : 00000000 00000000, k1 : 00000000 00000000
    gp : 00000000 29133C00, sp : 00000000 3022FBB8, s8 : 00000000 00000054, ra : 00000000 22768424
    EPC : 22768478, ErrorEPC : 80412AB4, SREG : 500099E3
    MDLO : 87126668, MDHI : D990ADBB, BadVaddr : 00000014
    CacheErr_Icache : 0x007F7F00 - 000040D8, CacheErr_Dcache : 0x00000000 - 00001FA0
    TagLo_Icache : 0x00000000 - 23642303, DataLo_Icache : 0xAFBF0018 - 0D81ADDB
    DataHi_Icache: 0x00000000 - 00000001
    TagLo_Dcache : 0x00000000 - 2277E583, TagHi_Dcache : 0x00000000 - 0912BD81
    DataLo_Dcache: 0x00000001 - 2368110C, DataHi_Dcache : 0x00000000 - 0000001C
    TEXT_START : 0x21003178
    DATA_START : 0x260888A0
    Cause 0000040C (Code 0x3): TLB (store) exception
    Writing crashinfo to flash:crashinfo_20101028-220211-UTC
    22:02:11 UTC Thu Oct 28 2010: TLB (store) exception, CPU signal 10, PC = 0x22768478

    --------------------------------------------------------------------
    Possible software fault. Upon reccurence, please collect
    crashinfo, "show tech" and contact Cisco Technical Support.
    --------------------------------------------------------------------

    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z
    $0 : 00000000 00000000, AT : 00000000 29130000, v0 : 00000000 00000001, v1 : 00000000 0D8B8540
    a0 : 00000000 00000000, a1 : 00000000 0D8B8584, a2 : 00000000 2A2F8ABC, a3 : 00000000 00000004
    t0 : 00000000 00000020, t1 : 00000000 500099E1, t2 : 00000000 500081E0, t3 : FFFFFFFF FFFFFFF2
    t4 : 00000000 0000000E, t5 : 00000000 00000000, t6 : 00000000 0D95F890, t7 : 00000000 000001FF
    s0 : 00000000 00000000, s1 : 00000000 2A2FDB40, s2 : FFFFFFFF FFFFFFEC, s3 : 00000000 3080C980
    s4 : 00000000 0D95F89E, s5 : 00000000 2A300EE0, s6 : 00000000 00000000, s7 : 00000000 0000000E
    t8 : 00000000 000007FC, t9 : 00000000 2A300200, k0 : 00000000 00000000, k1 : 00000000 00000000
    gp : 00000000 29133C00, sp : 00000000 3022FBB8, s8 : 00000000 00000054, ra : 00000000 22768424
    EPC : 22768478, ErrorEPC : 80412AB4, SREG : 500099E3
    MDLO : 87126668, MDHI : D990ADBB, BadVaddr : 00000014
    CacheErr_Icache : 0x007F7F00 - 000040D8, CacheErr_Dcache : 0x00000000 - 00001FA0
    TagLo_Icache : 0x00000000 - 23642303, DataLo_Icache : 0xAFBF0018 - 0D81ADDB
    DataHi_Icache: 0x00000000 - 00000001
    TagLo_Dcache : 0x00000000 - 2277E583, TagHi_Dcache : 0x00000000 - 0912BD81
    DataLo_Dcache: 0x00000001 - 2368110C, DataHi_Dcache : 0x00000000 - 0000001C
    TEXT_START : 0x21003178
    DATA_START : 0x260888A0
    Cause 0000040C (Code 0x3): TLB (store) exception
    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z

    === Flushing messages (22:02:12 UTC Thu Oct 28 2010) ===
    Buffered messages:
    *Oct 28 20:52:40.075: %LINK-3-UPDOWN: Interface SM1/0, changed state to up
    *Oct 28 20:52:42.195: %LINK-3-UPDOWN: Interface GigabitEthernet0/0, changed state to up
    *Oct 28 20:52:42.195: %LINK-3-UPDOWN: Interface GigabitEthernet0/1, changed state to down
    *Oct 28 20:52:42.195: %LINK-3-UPDOWN: Interface GigabitEthernet0/2, changed state to down
    *Oct 28 20:52:44.631: %LINK-3-UPDOWN: Interface SM1/1, changed state to up
    *Oct 28 20:53:01.655: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/0, changed state to up
    *Oct 28 20:53:01.923: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/1, changed state to up
    *Oct 28 20:53:02.075: %LINK-3-UPDOWN: Interface Foreign Exchange Station 0/1/0, changed state to up
    *Oct 28 20:53:02.075: %LINK-3-UPDOWN: Interface Foreign Exchange Station 0/1/1, changed state to up
    *Oct 28 20:53:43.739: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/0, changed state to operational status down due to cable removal
    *Oct 28 20:53:44.739: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/1, changed state to operational status down due to cable removal
    Queued messages:
    No warm reboot Storage
    *** System received a Bus Error exception ***
    signal= 0xa, code= 0x40c, context= 0x29726b74
    PC = 0x22768478, SP = 0x3022fbb8, RA = 0x22768424
    Cause Reg = 0x0000040c, Status Reg = 0x500099e3
    System Bootstrap, Version 15.0(1r)M6, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 2010 by cisco Systems, Inc.
    Total memory size = 512 MB - On-board = 512 MB, DIMM0 = 0 MB
    CISCO2911/K9 platform with 524288 Kbytes of main memory
    Main memory is configured to 72/-1(On-board/DIMM0) bit mode with ECC enabled

    Readonly ROMMON initialized
    program load complete, entry point: 0x80803000, size: 0x1b340

    IOS Image Load Test
    ___________________
    Digitally Signed Development Software
    program load complete, entry point: 0x81000000, size: 0x40b6b74
    Self decompressing the image : #############################################################################################################

    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2691036>
    or simply reply to this email.
    -- --
    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2691978>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2699015>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2699042>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2699089>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2699640>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2704890>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2703353>
    or simply reply to this email.

    Subject: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-
    Replied by: Ken Romo on 20-11-2010 01:34:37 AM
    Radhika,
     
    Anything new here today?
     
    Thanks again,
     
    Ken
     
     
    Ken,

    Right now it looks an IOS bug but we need to reproduce this in house so we can confirm for sure. I will keep you in the loop on what we find. If it turns out to be an issue with this particular PVDM I will let you know.



    Appreciate all your help with this.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Tuesday, November 02, 2010 9:51 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    So what is the root cause?

    The IOS or the PVDMS?

    Do I need to RMA my PVDMS?

    Let me know thank you.

    Ken


    Ken,

    Thanks for the information. We will check internally if this has been tested. I will cancel the debug session for today since we most likely have the root cause for the issue. We will try to reproduce this internally and if we need further information from you will setup a different session.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Tuesday, November 02, 2010 8:49 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    The PVDMS is:

    PVDM3-16 V01
    S/N FOC14200FNK

    Is this what you were looking for?

    Ken


    Ken,

    I am not sure if it is the PVDM that is bad but it could be a bug in the IOS image also where you have pvdm and the SRE module it could be some issue. For now can you continute to do beta for SRE-v without the PVDMS.



    I will check with the team and get back to you as to how to proceed.



    Can you let me know what PVDM models you have so we can try to reproduce this in our lab.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Monday, November 01, 2010 3:59 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    I pulled the PVDM and it is working.

    Does this mean the PVDM is bad?

    Ken


    Ken,

    Please try out the new image sent by Brett to you when you get a chance. Also one difference we noticed is that you have PVDM¿s in your setup that we don not have in our test setup. Would it be possible to remove the PVDMS temporarily and try the ping? This may help us root cause the issue.



    I will also schedule a WebEx for tomorrow morning 10:30 PST with the IOS developer so we can take a look if the change of IOS image and removal of PVDM¿s does not solve the issue. Please let me know if that time slot does not work for you.



    Thanks,

    Radhika





    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Monday, November 01, 2010 11:19 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    Here you go:

    boxer#show vlan-switch
    VLAN Name Status Ports
    ---- -------------------------------- --------- -------------------------------
    1 default active
    1002 fddi-default act/unsup
    1003 token-ring-default act/unsup
    1004 fddinet-default act/unsup
    1005 trnet-default act/unsup
    VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2
    ---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------
    1 enet 100001 1500 - - - - - 1002 1003
    1002 fddi 101002 1500 - - - - - 1 1003
    1003 tr 101003 1500 1005 0 - - srb 1 1002
    1004 fdnet 101004 1500 - - 1 ibm - 0 0
    1005 trnet 101005 1500 - - 1 ibm - 0 0


    boxer#sh platform mgf module
    Registered Module Information
    Code: NR - Not Registered, TM - Trust Mode, SP - Scheduling Profile
    BL - Buffer Level, TR - Traffic Rate, PT - Pause Threshold
    slot vlan type/ID TM SP BL TR PT
    ---- ---- ---------- ------- --- ------ ----- ----
    ISM NR
    EHWIC-0 NR
    EHWIC-1 NR
    EHWIC-2 NR
    EHWIC-3 NR
    PVDM-0 2 PVDM/5 UP 1 low 1000 low
    PVDM-1 2 PVDM/5 UP 1 low 1000 low
    SM-1 1 Switch/3 UP 1 low 1000 high




    Thanks Ken. Can you also give us the output of the following.



    1) show vlan-switch

    2) ¿show platform mgf module¿ before the crash happens.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Monday, November 01, 2010 10:50 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    I will try whatever you suggest, just let me know when you have posted the new IOS.

    Below is my config:

    boxer#sh run
    Building configuration...

    Current configuration : 5777 bytes
    !
    version 15.1
    service timestamps debug datetime msec
    service timestamps log datetime msec
    no service password-encryption
    !
    hostname boxer
    !
    boot-start-marker
    boot system flash0 c2900-universalk9-mz.SSA.151-2.19.T
    boot-end-marker
    !
    !
    logging buffered 51200 warnings
    !
    no aaa new-model
    !
    no ipv6 cef
    ip source-route
    ip cef
    !
    !
    !
    !
    !
    ip domain name yourdomain.com
    multilink bundle-name authenticated
    !
    !
    !
    !
    !
    crypto pki token default removal timeout 0
    !
    crypto pki trustpoint TP-self-signed-1999750280
    enrollment selfsigned
    subject-name cn=IOS-Self-Signed-Certificate-1999750280
    revocation-check none
    rsakeypair TP-self-signed-1999750280
    !
    !
    crypto pki certificate chain TP-self-signed-1999750280
    certificate self-signed 01
    3082024C 308201B5 A0030201 02020101 300D0609 2A864886 F70D0101 04050030
    31312F30 2D060355 04031326 494F532D 53656C66 2D536967 6E65642D 43657274
    69666963 6174652D 31393939 37353032 3830301E 170D3130 31303230 32323335
    32365A17 0D323030 31303130 30303030 305A3031 312F302D 06035504 03132649
    4F532D53 656C662D 5369676E 65642D43 65727469 66696361 74652D31 39393937
    35303238 3030819F 300D0609 2A864886 F70D0101 01050003 818D0030 81890281
    81009378 2E139D79 DCA59865 14AB3398 870362B7 40BB9C13 A5DC5315 6108DF92
    5E78CF06 A40D4DB5 B66D410E FAFE75AC 764997B1 5C551A47 CFA00109 520352EC
    33A69E24 B3C1175B 136FC62A 8BE4637E B834059B FC7CAA6E 957DA0BB 66D8DC49
    80F82890 981FFCFE 0DC7E6F9 53287989 3887C5F6 AF59D0BE B502E11E FD16F556
    DBB90203 010001A3 74307230 0F060355 1D130101 FF040530 030101FF 301F0603
    551D1104 18301682 14626F78 65722E79 6F757264 6F6D6169 6E2E636F 6D301F06
    03551D23 04183016 80143541 7934E424 4B9A60DB E6C908C3 C20BAA17 D058301D
    0603551D 0E041604 14354179 34E4244B 9A60DBE6 C908C3C2 0BAA17D0 58300D06
    092A8648 86F70D01 01040500 03818100 3D222AB5 177D452F 153DCA26 1D7ECB49
    58BCBF60 DA18DC04 94B82EA3 76884EBC D7131641 08687C04 6C6645DF 78B2D2F8
    409BCAD7 50AF5091 B99614FD C2424D89 407A9109 BCA20473 F4CE33D4 4B126483
    C240C0B9 7A628E53 E419FEC3 B8853671 03113F5E 47FA8120 9F9A7A9D 11498FE0
    82C96578 8FD9770A EBD27F73 DF2E1487
    quit
    voice-card 0
    !
    !
    !
    !
    !
    !
    !
    license udi pid CISCO2911/K9 sn FTX1422A077
    hw-module pvdm 0/0
    !
    hw-module sm 1
    !
    !
    !
    username jack privilege 15 secret 5 $1$c5QR$fYGTbhWRKsBZ1JpNyIQGG1
    username marco privilege 15 secret 5 $1$amqq$5pI0T7mUViDL5Y.NqX/yz.
    !
    redundancy
    !
    !
    !
    !
    !
    !
    interface GigabitEthernet0/0
    description To tusqa network
    ip address 172.17.17.130 255.255.248.0
    duplex auto
    speed auto
    !
    interface GigabitEthernet0/1
    no ip address
    shutdown
    duplex auto
    speed auto
    !
    interface GigabitEthernet0/2
    no ip address
    shutdown
    duplex auto
    speed auto
    !
    interface SM1/0
    ip unnumbered GigabitEthernet0/0
    service-module ip address 172.17.17.129 255.255.248.0
    !Application: SRE-V Running on SMV
    service-module ip default-gateway 172.17.17.130
    service-module mgf ip address 10.62.64.1 255.255.255.0
    service-module mgf ip default-gateway 10.62.64.2
    !
    interface SM1/1
    description Internal switch interface connected to Service Module
    switchport mode trunk
    !
    interface Vlan1
    ip address 10.62.64.2 255.255.255.0
    !
    ip forward-protocol nd
    !
    ip http server
    ip http access-class 23
    ip http authentication local
    ip http secure-server
    ip http timeout-policy idle 60 life 86400 requests 10000
    !
    ip route 172.17.17.129 255.255.255.255 SM1/0
    !
    !
    !
    !
    control-plane
    !
    !
    voice-port 0/0/0
    !
    voice-port 0/0/1
    !
    voice-port 0/1/0
    !
    voice-port 0/1/1
    !
    !
    !
    mgcp profile default
    !
    !
    !
    !
    !
    gatekeeper
    shutdown
    !
    !
    banner exec ^C
    % Password expiration warning.
    -----------------------------------------------------------------------
    Cisco Configuration Professional (Cisco CP) is installed on this device
    and it provides the default username "cisco" for one-time use. If you have
    already used the username "cisco" to login to the router and your IOS image
    supports the "one-time" user option, then this username has already expired.
    You will not be able to login to the router with this username after you exit
    this session.
    It is strongly suggested that you create a new username with a privilege level
    of 15 using the following command.
    username <myuser> privilege 15 secret 0 <mypassword>
    Replace <myuser> and <mypassword> with the username and password you want to
    use.
    -----------------------------------------------------------------------
    ^C
    banner login ^C
    -----------------------------------------------------------------------
    Cisco Configuration Professional (Cisco CP) is installed on this device.
    This feature requires the one-time use of the username "cisco" with the
    password "cisco". These default credentials have a privilege level of 15.
    YOU MUST USE CISCO CP or the CISCO IOS CLI TO CHANGE THESE PUBLICLY-KNOWN
    CREDENTIALS
    Here are the Cisco IOS commands.
    username <myuser> privilege 15 secret 0 <mypassword>
    no username cisco
    Replace <myuser> and <mypassword> with the username and password you want
    to use.
    IF YOU DO NOT CHANGE THE PUBLICLY-KNOWN CREDENTIALS, YOU WILL NOT BE ABLE
    TO LOG INTO THE DEVICE AGAIN AFTER YOU HAVE LOGGED OFF.
    For more information about Cisco CP please follow the instructions in the
    QUICK START GUIDE for your router or go to http://www.cisco.com/go/ciscocp
    -----------------------------------------------------------------------
    ^C
    !
    line con 0
    login local
    line aux 0
    line 67
    no activation-character
    no exec
    transport preferred none
    transport input all
    transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
    stopbits 1
    flowcontrol software
    line vty 0 4
    privilege level 15
    login local
    transport input telnet
    line vty 5 15
    privilege level 15
    login local
    transport input telnet ssh
    !
    exception data-corruption buffer truncate
    scheduler allocate 20000 1000
    end



    Ken, Thanks for trying out the image for us. We are trying to reproduce this on our end but have had no luck so far. Can you please send us the output of show running-config from your router.



    Also we have one more image that we would like you to try it out before the debusg session would that be ok?



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Monday, November 01, 2010 10:22 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------

    Radhika,

    I tried the new OS and still getting same IOS crash.
    As mentioned I will work around your schedule so let me if you were able to get someone from the IOS team to help troubleshoot today.

    Thanks in advance,

    Ken Romo


    Ken,

    I am trying to get some help from the IOS team since this a router crash. So I will setup the webex session to debug for some time Monday so we can collect all the information and try out any suggestion from them.



    For Now We will post a newer IOS image to the beta Site and can you give that a try to see if that will solve the issue.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Friday, October 29, 2010 8:24 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    I will work around your schedule, anytime you are available, I will make myself available.
    email:
    kromo@opentext.com

    Thanks in advance,

    Ken Romo

    +++++++++++++++++++++++++++++++++

    Ken,

    Would a webex session tomorrow morning (any time between 10:00 and 1:00) work for you? Let me know the time that would work for you and also your email address so I can send you a webex invite.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Thursday, October 28, 2010 3:12 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Radhika Miriyala in Service Ready Engine Virtualizatio



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    No worries, we are trying to work this out together and I appreciate the help.
    s/m 1/1 is set as trunk but I went ahead and reconfigured to truank again and reloaded OS and get the same crash when I ping to the MGF interface from the SRE (I attached the errors at the bottom of this message).

    Ken,

    Sorry I just realized the mistake. I meant to say make the interface sm 1/1 as trunk.

    Sorry about the confusion.



    Please try it out.



    Thanks,

    Radhika



    boxer#
    %ALIGN-1-FATAL: Illegal access to a low address 22:02:10 UTC Thu Oct 28 2010
    addr=0x14, pc=0x22765BD8z , ra=0x22765B84z , sp=0x3022FBB8
    %ALIGN-1-FATAL: Illegal access to a low address 22:02:11 UTC Thu Oct 28 2010
    addr=0x14, pc=0x22765BD8z , ra=0x22765B84z , sp=0x3022FBB8

    22:02:11 UTC Thu Oct 28 2010: TLB (store) exception, CPU signal 10, PC = 0x22768478

    --------------------------------------------------------------------
    Possible software fault. Upon reccurence, please collect
    crashinfo, "show tech" and contact Cisco Technical Support.
    --------------------------------------------------------------------

    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z
    $0 : 00000000 00000000, AT : 00000000 29130000, v0 : 00000000 00000001, v1 : 00000000 0D8B8540
    a0 : 00000000 00000000, a1 : 00000000 0D8B8584, a2 : 00000000 2A2F8ABC, a3 : 00000000 00000004
    t0 : 00000000 00000020, t1 : 00000000 500099E1, t2 : 00000000 500081E0, t3 : FFFFFFFF FFFFFFF2
    t4 : 00000000 0000000E, t5 : 00000000 00000000, t6 : 00000000 0D95F890, t7 : 00000000 000001FF
    s0 : 00000000 00000000, s1 : 00000000 2A2FDB40, s2 : FFFFFFFF FFFFFFEC, s3 : 00000000 3080C980
    s4 : 00000000 0D95F89E, s5 : 00000000 2A300EE0, s6 : 00000000 00000000, s7 : 00000000 0000000E
    t8 : 00000000 000007FC, t9 : 00000000 2A300200, k0 : 00000000 00000000, k1 : 00000000 00000000
    gp : 00000000 29133C00, sp : 00000000 3022FBB8, s8 : 00000000 00000054, ra : 00000000 22768424
    EPC : 22768478, ErrorEPC : 80412AB4, SREG : 500099E3
    MDLO : 87126668, MDHI : D990ADBB, BadVaddr : 00000014
    CacheErr_Icache : 0x007F7F00 - 000040D8, CacheErr_Dcache : 0x00000000 - 00001FA0
    TagLo_Icache : 0x00000000 - 23642303, DataLo_Icache : 0xAFBF0018 - 0D81ADDB
    DataHi_Icache: 0x00000000 - 00000001
    TagLo_Dcache : 0x00000000 - 2277E583, TagHi_Dcache : 0x00000000 - 0912BD81
    DataLo_Dcache: 0x00000001 - 2368110C, DataHi_Dcache : 0x00000000 - 0000001C
    TEXT_START : 0x21003178
    DATA_START : 0x260888A0
    Cause 0000040C (Code 0x3): TLB (store) exception

    22:02:11 UTC Thu Oct 28 2010: TLB (store) exception, CPU signal 10, PC = 0x22768478

    --------------------------------------------------------------------
    Possible software fault. Upon reccurence, please collect
    crashinfo, "show tech" and contact Cisco Technical Support.
    --------------------------------------------------------------------

    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z
    $0 : 00000000 00000000, AT : 00000000 29130000, v0 : 00000000 00000001, v1 : 00000000 0D8B8540
    a0 : 00000000 00000000, a1 : 00000000 0D8B8584, a2 : 00000000 2A2F8ABC, a3 : 00000000 00000004
    t0 : 00000000 00000020, t1 : 00000000 500099E1, t2 : 00000000 500081E0, t3 : FFFFFFFF FFFFFFF2
    t4 : 00000000 0000000E, t5 : 00000000 00000000, t6 : 00000000 0D95F890, t7 : 00000000 000001FF
    s0 : 00000000 00000000, s1 : 00000000 2A2FDB40, s2 : FFFFFFFF FFFFFFEC, s3 : 00000000 3080C980
    s4 : 00000000 0D95F89E, s5 : 00000000 2A300EE0, s6 : 00000000 00000000, s7 : 00000000 0000000E
    t8 : 00000000 000007FC, t9 : 00000000 2A300200, k0 : 00000000 00000000, k1 : 00000000 00000000
    gp : 00000000 29133C00, sp : 00000000 3022FBB8, s8 : 00000000 00000054, ra : 00000000 22768424
    EPC : 22768478, ErrorEPC : 80412AB4, SREG : 500099E3
    MDLO : 87126668, MDHI : D990ADBB, BadVaddr : 00000014
    CacheErr_Icache : 0x007F7F00 - 000040D8, CacheErr_Dcache : 0x00000000 - 00001FA0
    TagLo_Icache : 0x00000000 - 23642303, DataLo_Icache : 0xAFBF0018 - 0D81ADDB
    DataHi_Icache: 0x00000000 - 00000001
    TagLo_Dcache : 0x00000000 - 2277E583, TagHi_Dcache : 0x00000000 - 0912BD81
    DataLo_Dcache: 0x00000001 - 2368110C, DataHi_Dcache : 0x00000000 - 0000001C
    TEXT_START : 0x21003178
    DATA_START : 0x260888A0
    Cause 0000040C (Code 0x3): TLB (store) exception
    Writing crashinfo to flash:crashinfo_20101028-220211-UTC
    22:02:11 UTC Thu Oct 28 2010: TLB (store) exception, CPU signal 10, PC = 0x22768478

    --------------------------------------------------------------------
    Possible software fault. Upon reccurence, please collect
    crashinfo, "show tech" and contact Cisco Technical Support.
    --------------------------------------------------------------------

    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z
    $0 : 00000000 00000000, AT : 00000000 29130000, v0 : 00000000 00000001, v1 : 00000000 0D8B8540
    a0 : 00000000 00000000, a1 : 00000000 0D8B8584, a2 : 00000000 2A2F8ABC, a3 : 00000000 00000004
    t0 : 00000000 00000020, t1 : 00000000 500099E1, t2 : 00000000 500081E0, t3 : FFFFFFFF FFFFFFF2
    t4 : 00000000 0000000E, t5 : 00000000 00000000, t6 : 00000000 0D95F890, t7 : 00000000 000001FF
    s0 : 00000000 00000000, s1 : 00000000 2A2FDB40, s2 : FFFFFFFF FFFFFFEC, s3 : 00000000 3080C980
    s4 : 00000000 0D95F89E, s5 : 00000000 2A300EE0, s6 : 00000000 00000000, s7 : 00000000 0000000E
    t8 : 00000000 000007FC, t9 : 00000000 2A300200, k0 : 00000000 00000000, k1 : 00000000 00000000
    gp : 00000000 29133C00, sp : 00000000 3022FBB8, s8 : 00000000 00000054, ra : 00000000 22768424
    EPC : 22768478, ErrorEPC : 80412AB4, SREG : 500099E3
    MDLO : 87126668, MDHI : D990ADBB, BadVaddr : 00000014
    CacheErr_Icache : 0x007F7F00 - 000040D8, CacheErr_Dcache : 0x00000000 - 00001FA0
    TagLo_Icache : 0x00000000 - 23642303, DataLo_Icache : 0xAFBF0018 - 0D81ADDB
    DataHi_Icache: 0x00000000 - 00000001
    TagLo_Dcache : 0x00000000 - 2277E583, TagHi_Dcache : 0x00000000 - 0912BD81
    DataLo_Dcache: 0x00000001 - 2368110C, DataHi_Dcache : 0x00000000 - 0000001C
    TEXT_START : 0x21003178
    DATA_START : 0x260888A0
    Cause 0000040C (Code 0x3): TLB (store) exception
    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z

    === Flushing messages (22:02:12 UTC Thu Oct 28 2010) ===
    Buffered messages:
    *Oct 28 20:52:40.075: %LINK-3-UPDOWN: Interface SM1/0, changed state to up
    *Oct 28 20:52:42.195: %LINK-3-UPDOWN: Interface GigabitEthernet0/0, changed state to up
    *Oct 28 20:52:42.195: %LINK-3-UPDOWN: Interface GigabitEthernet0/1, changed state to down
    *Oct 28 20:52:42.195: %LINK-3-UPDOWN: Interface GigabitEthernet0/2, changed state to down
    *Oct 28 20:52:44.631: %LINK-3-UPDOWN: Interface SM1/1, changed state to up
    *Oct 28 20:53:01.655: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/0, changed state to up
    *Oct 28 20:53:01.923: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/1, changed state to up
    *Oct 28 20:53:02.075: %LINK-3-UPDOWN: Interface Foreign Exchange Station 0/1/0, changed state to up
    *Oct 28 20:53:02.075: %LINK-3-UPDOWN: Interface Foreign Exchange Station 0/1/1, changed state to up
    *Oct 28 20:53:43.739: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/0, changed state to operational status down due to cable removal
    *Oct 28 20:53:44.739: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/1, changed state to operational status down due to cable removal
    Queued messages:
    No warm reboot Storage
    *** System received a Bus Error exception ***
    signal= 0xa, code= 0x40c, context= 0x29726b74
    PC = 0x22768478, SP = 0x3022fbb8, RA = 0x22768424
    Cause Reg = 0x0000040c, Status Reg = 0x500099e3
    System Bootstrap, Version 15.0(1r)M6, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 2010 by cisco Systems, Inc.
    Total memory size = 512 MB - On-board = 512 MB, DIMM0 = 0 MB
    CISCO2911/K9 platform with 524288 Kbytes of main memory
    Main memory is configured to 72/-1(On-board/DIMM0) bit mode with ECC enabled

    Readonly ROMMON initialized
    program load complete, entry point: 0x80803000, size: 0x1b340

    IOS Image Load Test
    ___________________
    Digitally Signed Development Software
    program load complete, entry point: 0x81000000, size: 0x40b6b74
    Self decompressing the image : #############################################################################################################

    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2691036>
    or simply reply to this email.
    -- --
    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2691978>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2699015>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2699042>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2699089>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2699640>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2704890>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2703353>
    or simply reply to this email.


    Subject: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-
    Replied by: Radhika Miriyala on 20-11-2010 01:34:37 AM
    Ken,

    The IOS team is trying to reproduce this in their setup. I will let you know what the finding are or if we need a debug session with you (if they can¿t reproduce in their setup)



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Wednesday, November 03, 2010 9:03 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    Anything new here today?

    Thanks again,

    Ken



    Ken,

    Right now it looks an IOS bug but we need to reproduce this in house so we can confirm for sure. I will keep you in the loop on what we find. If it turns out to be an issue with this particular PVDM I will let you know.



    Appreciate all your help with this.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Tuesday, November 02, 2010 9:51 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    So what is the root cause?

    The IOS or the PVDMS?

    Do I need to RMA my PVDMS?

    Let me know thank you.

    Ken


    Ken,

    Thanks for the information. We will check internally if this has been tested. I will cancel the debug session for today since we most likely have the root cause for the issue. We will try to reproduce this internally and if we need further information from you will setup a different session.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Tuesday, November 02, 2010 8:49 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    The PVDMS is:

    PVDM3-16 V01
    S/N FOC14200FNK

    Is this what you were looking for?

    Ken


    Ken,

    I am not sure if it is the PVDM that is bad but it could be a bug in the IOS image also where you have pvdm and the SRE module it could be some issue. For now can you continute to do beta for SRE-v without the PVDMS.



    I will check with the team and get back to you as to how to proceed.



    Can you let me know what PVDM models you have so we can try to reproduce this in our lab.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Monday, November 01, 2010 3:59 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    I pulled the PVDM and it is working.

    Does this mean the PVDM is bad?

    Ken


    Ken,

    Please try out the new image sent by Brett to you when you get a chance. Also one difference we noticed is that you have PVDM¿s in your setup that we don not have in our test setup. Would it be possible to remove the PVDMS temporarily and try the ping? This may help us root cause the issue.



    I will also schedule a WebEx for tomorrow morning 10:30 PST with the IOS developer so we can take a look if the change of IOS image and removal of PVDM¿s does not solve the issue. Please let me know if that time slot does not work for you.



    Thanks,

    Radhika





    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Monday, November 01, 2010 11:19 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    Here you go:

    boxer#show vlan-switch
    VLAN Name Status Ports
    ---- -------------------------------- --------- -------------------------------
    1 default active
    1002 fddi-default act/unsup
    1003 token-ring-default act/unsup
    1004 fddinet-default act/unsup
    1005 trnet-default act/unsup
    VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2
    ---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------
    1 enet 100001 1500 - - - - - 1002 1003
    1002 fddi 101002 1500 - - - - - 1 1003
    1003 tr 101003 1500 1005 0 - - srb 1 1002
    1004 fdnet 101004 1500 - - 1 ibm - 0 0
    1005 trnet 101005 1500 - - 1 ibm - 0 0


    boxer#sh platform mgf module
    Registered Module Information
    Code: NR - Not Registered, TM - Trust Mode, SP - Scheduling Profile
    BL - Buffer Level, TR - Traffic Rate, PT - Pause Threshold
    slot vlan type/ID TM SP BL TR PT
    ---- ---- ---------- ------- --- ------ ----- ----
    ISM NR
    EHWIC-0 NR
    EHWIC-1 NR
    EHWIC-2 NR
    EHWIC-3 NR
    PVDM-0 2 PVDM/5 UP 1 low 1000 low
    PVDM-1 2 PVDM/5 UP 1 low 1000 low
    SM-1 1 Switch/3 UP 1 low 1000 high




    Thanks Ken. Can you also give us the output of the following.



    1) show vlan-switch

    2) ¿show platform mgf module¿ before the crash happens.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Monday, November 01, 2010 10:50 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    I will try whatever you suggest, just let me know when you have posted the new IOS.

    Below is my config:

    boxer#sh run
    Building configuration...

    Current configuration : 5777 bytes
    !
    version 15.1
    service timestamps debug datetime msec
    service timestamps log datetime msec
    no service password-encryption
    !
    hostname boxer
    !
    boot-start-marker
    boot system flash0 c2900-universalk9-mz.SSA.151-2.19.T
    boot-end-marker
    !
    !
    logging buffered 51200 warnings
    !
    no aaa new-model
    !
    no ipv6 cef
    ip source-route
    ip cef
    !
    !
    !
    !
    !
    ip domain name yourdomain.com
    multilink bundle-name authenticated
    !
    !
    !
    !
    !
    crypto pki token default removal timeout 0
    !
    crypto pki trustpoint TP-self-signed-1999750280
    enrollment selfsigned
    subject-name cn=IOS-Self-Signed-Certificate-1999750280
    revocation-check none
    rsakeypair TP-self-signed-1999750280
    !
    !
    crypto pki certificate chain TP-self-signed-1999750280
    certificate self-signed 01
    3082024C 308201B5 A0030201 02020101 300D0609 2A864886 F70D0101 04050030
    31312F30 2D060355 04031326 494F532D 53656C66 2D536967 6E65642D 43657274
    69666963 6174652D 31393939 37353032 3830301E 170D3130 31303230 32323335
    32365A17 0D323030 31303130 30303030 305A3031 312F302D 06035504 03132649
    4F532D53 656C662D 5369676E 65642D43 65727469 66696361 74652D31 39393937
    35303238 3030819F 300D0609 2A864886 F70D0101 01050003 818D0030 81890281
    81009378 2E139D79 DCA59865 14AB3398 870362B7 40BB9C13 A5DC5315 6108DF92
    5E78CF06 A40D4DB5 B66D410E FAFE75AC 764997B1 5C551A47 CFA00109 520352EC
    33A69E24 B3C1175B 136FC62A 8BE4637E B834059B FC7CAA6E 957DA0BB 66D8DC49
    80F82890 981FFCFE 0DC7E6F9 53287989 3887C5F6 AF59D0BE B502E11E FD16F556
    DBB90203 010001A3 74307230 0F060355 1D130101 FF040530 030101FF 301F0603
    551D1104 18301682 14626F78 65722E79 6F757264 6F6D6169 6E2E636F 6D301F06
    03551D23 04183016 80143541 7934E424 4B9A60DB E6C908C3 C20BAA17 D058301D
    0603551D 0E041604 14354179 34E4244B 9A60DBE6 C908C3C2 0BAA17D0 58300D06
    092A8648 86F70D01 01040500 03818100 3D222AB5 177D452F 153DCA26 1D7ECB49
    58BCBF60 DA18DC04 94B82EA3 76884EBC D7131641 08687C04 6C6645DF 78B2D2F8
    409BCAD7 50AF5091 B99614FD C2424D89 407A9109 BCA20473 F4CE33D4 4B126483
    C240C0B9 7A628E53 E419FEC3 B8853671 03113F5E 47FA8120 9F9A7A9D 11498FE0
    82C96578 8FD9770A EBD27F73 DF2E1487
    quit
    voice-card 0
    !
    !
    !
    !
    !
    !
    !
    license udi pid CISCO2911/K9 sn FTX1422A077
    hw-module pvdm 0/0
    !
    hw-module sm 1
    !
    !
    !
    username jack privilege 15 secret 5 $1$c5QR$fYGTbhWRKsBZ1JpNyIQGG1
    username marco privilege 15 secret 5 $1$amqq$5pI0T7mUViDL5Y.NqX/yz.
    !
    redundancy
    !
    !
    !
    !
    !
    !
    interface GigabitEthernet0/0
    description To tusqa network
    ip address 172.17.17.130 255.255.248.0
    duplex auto
    speed auto
    !
    interface GigabitEthernet0/1
    no ip address
    shutdown
    duplex auto
    speed auto
    !
    interface GigabitEthernet0/2
    no ip address
    shutdown
    duplex auto
    speed auto
    !
    interface SM1/0
    ip unnumbered GigabitEthernet0/0
    service-module ip address 172.17.17.129 255.255.248.0
    !Application: SRE-V Running on SMV
    service-module ip default-gateway 172.17.17.130
    service-module mgf ip address 10.62.64.1 255.255.255.0
    service-module mgf ip default-gateway 10.62.64.2
    !
    interface SM1/1
    description Internal switch interface connected to Service Module
    switchport mode trunk
    !
    interface Vlan1
    ip address 10.62.64.2 255.255.255.0
    !
    ip forward-protocol nd
    !
    ip http server
    ip http access-class 23
    ip http authentication local
    ip http secure-server
    ip http timeout-policy idle 60 life 86400 requests 10000
    !
    ip route 172.17.17.129 255.255.255.255 SM1/0
    !
    !
    !
    !
    control-plane
    !
    !
    voice-port 0/0/0
    !
    voice-port 0/0/1
    !
    voice-port 0/1/0
    !
    voice-port 0/1/1
    !
    !
    !
    mgcp profile default
    !
    !
    !
    !
    !
    gatekeeper
    shutdown
    !
    !
    banner exec ^C
    % Password expiration warning.
    -----------------------------------------------------------------------
    Cisco Configuration Professional (Cisco CP) is installed on this device
    and it provides the default username "cisco" for one-time use. If you have
    already used the username "cisco" to login to the router and your IOS image
    supports the "one-time" user option, then this username has already expired.
    You will not be able to login to the router with this username after you exit
    this session.
    It is strongly suggested that you create a new username with a privilege level
    of 15 using the following command.
    username <myuser> privilege 15 secret 0 <mypassword>
    Replace <myuser> and <mypassword> with the username and password you want to
    use.
    -----------------------------------------------------------------------
    ^C
    banner login ^C
    -----------------------------------------------------------------------
    Cisco Configuration Professional (Cisco CP) is installed on this device.
    This feature requires the one-time use of the username "cisco" with the
    password "cisco". These default credentials have a privilege level of 15.
    YOU MUST USE CISCO CP or the CISCO IOS CLI TO CHANGE THESE PUBLICLY-KNOWN
    CREDENTIALS
    Here are the Cisco IOS commands.
    username <myuser> privilege 15 secret 0 <mypassword>
    no username cisco
    Replace <myuser> and <mypassword> with the username and password you want
    to use.
    IF YOU DO NOT CHANGE THE PUBLICLY-KNOWN CREDENTIALS, YOU WILL NOT BE ABLE
    TO LOG INTO THE DEVICE AGAIN AFTER YOU HAVE LOGGED OFF.
    For more information about Cisco CP please follow the instructions in the
    QUICK START GUIDE for your router or go to http://www.cisco.com/go/ciscocp
    -----------------------------------------------------------------------
    ^C
    !
    line con 0
    login local
    line aux 0
    line 67
    no activation-character
    no exec
    transport preferred none
    transport input all
    transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
    stopbits 1
    flowcontrol software
    line vty 0 4
    privilege level 15
    login local
    transport input telnet
    line vty 5 15
    privilege level 15
    login local
    transport input telnet ssh
    !
    exception data-corruption buffer truncate
    scheduler allocate 20000 1000
    end



    Ken, Thanks for trying out the image for us. We are trying to reproduce this on our end but have had no luck so far. Can you please send us the output of show running-config from your router.



    Also we have one more image that we would like you to try it out before the debusg session would that be ok?



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Monday, November 01, 2010 10:22 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------

    Radhika,

    I tried the new OS and still getting same IOS crash.
    As mentioned I will work around your schedule so let me if you were able to get someone from the IOS team to help troubleshoot today.

    Thanks in advance,

    Ken Romo


    Ken,

    I am trying to get some help from the IOS team since this a router crash. So I will setup the webex session to debug for some time Monday so we can collect all the information and try out any suggestion from them.



    For Now We will post a newer IOS image to the beta Site and can you give that a try to see if that will solve the issue.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Friday, October 29, 2010 8:24 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    I will work around your schedule, anytime you are available, I will make myself available.
    email:
    kromo@opentext.com

    Thanks in advance,

    Ken Romo

    +++++++++++++++++++++++++++++++++

    Ken,

    Would a webex session tomorrow morning (any time between 10:00 and 1:00) work for you? Let me know the time that would work for you and also your email address so I can send you a webex invite.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Thursday, October 28, 2010 3:12 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Radhika Miriyala in Service Ready Engine Virtualizatio



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    No worries, we are trying to work this out together and I appreciate the help.
    s/m 1/1 is set as trunk but I went ahead and reconfigured to truank again and reloaded OS and get the same crash when I ping to the MGF interface from the SRE (I attached the errors at the bottom of this message).

    Ken,

    Sorry I just realized the mistake. I meant to say make the interface sm 1/1 as trunk.

    Sorry about the confusion.



    Please try it out.



    Thanks,

    Radhika



    boxer#
    %ALIGN-1-FATAL: Illegal access to a low address 22:02:10 UTC Thu Oct 28 2010
    addr=0x14, pc=0x22765BD8z , ra=0x22765B84z , sp=0x3022FBB8
    %ALIGN-1-FATAL: Illegal access to a low address 22:02:11 UTC Thu Oct 28 2010
    addr=0x14, pc=0x22765BD8z , ra=0x22765B84z , sp=0x3022FBB8

    22:02:11 UTC Thu Oct 28 2010: TLB (store) exception, CPU signal 10, PC = 0x22768478

    --------------------------------------------------------------------
    Possible software fault. Upon reccurence, please collect
    crashinfo, "show tech" and contact Cisco Technical Support.
    --------------------------------------------------------------------

    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z
    $0 : 00000000 00000000, AT : 00000000 29130000, v0 : 00000000 00000001, v1 : 00000000 0D8B8540
    a0 : 00000000 00000000, a1 : 00000000 0D8B8584, a2 : 00000000 2A2F8ABC, a3 : 00000000 00000004
    t0 : 00000000 00000020, t1 : 00000000 500099E1, t2 : 00000000 500081E0, t3 : FFFFFFFF FFFFFFF2
    t4 : 00000000 0000000E, t5 : 00000000 00000000, t6 : 00000000 0D95F890, t7 : 00000000 000001FF
    s0 : 00000000 00000000, s1 : 00000000 2A2FDB40, s2 : FFFFFFFF FFFFFFEC, s3 : 00000000 3080C980
    s4 : 00000000 0D95F89E, s5 : 00000000 2A300EE0, s6 : 00000000 00000000, s7 : 00000000 0000000E
    t8 : 00000000 000007FC, t9 : 00000000 2A300200, k0 : 00000000 00000000, k1 : 00000000 00000000
    gp : 00000000 29133C00, sp : 00000000 3022FBB8, s8 : 00000000 00000054, ra : 00000000 22768424
    EPC : 22768478, ErrorEPC : 80412AB4, SREG : 500099E3
    MDLO : 87126668, MDHI : D990ADBB, BadVaddr : 00000014
    CacheErr_Icache : 0x007F7F00 - 000040D8, CacheErr_Dcache : 0x00000000 - 00001FA0
    TagLo_Icache : 0x00000000 - 23642303, DataLo_Icache : 0xAFBF0018 - 0D81ADDB
    DataHi_Icache: 0x00000000 - 00000001
    TagLo_Dcache : 0x00000000 - 2277E583, TagHi_Dcache : 0x00000000 - 0912BD81
    DataLo_Dcache: 0x00000001 - 2368110C, DataHi_Dcache : 0x00000000 - 0000001C
    TEXT_START : 0x21003178
    DATA_START : 0x260888A0
    Cause 0000040C (Code 0x3): TLB (store) exception

    22:02:11 UTC Thu Oct 28 2010: TLB (store) exception, CPU signal 10, PC = 0x22768478

    --------------------------------------------------------------------
    Possible software fault. Upon reccurence, please collect
    crashinfo, "show tech" and contact Cisco Technical Support.
    --------------------------------------------------------------------

    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z
    $0 : 00000000 00000000, AT : 00000000 29130000, v0 : 00000000 00000001, v1 : 00000000 0D8B8540
    a0 : 00000000 00000000, a1 : 00000000 0D8B8584, a2 : 00000000 2A2F8ABC, a3 : 00000000 00000004
    t0 : 00000000 00000020, t1 : 00000000 500099E1, t2 : 00000000 500081E0, t3 : FFFFFFFF FFFFFFF2
    t4 : 00000000 0000000E, t5 : 00000000 00000000, t6 : 00000000 0D95F890, t7 : 00000000 000001FF
    s0 : 00000000 00000000, s1 : 00000000 2A2FDB40, s2 : FFFFFFFF FFFFFFEC, s3 : 00000000 3080C980
    s4 : 00000000 0D95F89E, s5 : 00000000 2A300EE0, s6 : 00000000 00000000, s7 : 00000000 0000000E
    t8 : 00000000 000007FC, t9 : 00000000 2A300200, k0 : 00000000 00000000, k1 : 00000000 00000000
    gp : 00000000 29133C00, sp : 00000000 3022FBB8, s8 : 00000000 00000054, ra : 00000000 22768424
    EPC : 22768478, ErrorEPC : 80412AB4, SREG : 500099E3
    MDLO : 87126668, MDHI : D990ADBB, BadVaddr : 00000014
    CacheErr_Icache : 0x007F7F00 - 000040D8, CacheErr_Dcache : 0x00000000 - 00001FA0
    TagLo_Icache : 0x00000000 - 23642303, DataLo_Icache : 0xAFBF0018 - 0D81ADDB
    DataHi_Icache: 0x00000000 - 00000001
    TagLo_Dcache : 0x00000000 - 2277E583, TagHi_Dcache : 0x00000000 - 0912BD81
    DataLo_Dcache: 0x00000001 - 2368110C, DataHi_Dcache : 0x00000000 - 0000001C
    TEXT_START : 0x21003178
    DATA_START : 0x260888A0
    Cause 0000040C (Code 0x3): TLB (store) exception
    Writing crashinfo to flash:crashinfo_20101028-220211-UTC
    22:02:11 UTC Thu Oct 28 2010: TLB (store) exception, CPU signal 10, PC = 0x22768478

    --------------------------------------------------------------------
    Possible software fault. Upon reccurence, please collect
    crashinfo, "show tech" and contact Cisco Technical Support.
    --------------------------------------------------------------------

    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z
    $0 : 00000000 00000000, AT : 00000000 29130000, v0 : 00000000 00000001, v1 : 00000000 0D8B8540
    a0 : 00000000 00000000, a1 : 00000000 0D8B8584, a2 : 00000000 2A2F8ABC, a3 : 00000000 00000004
    t0 : 00000000 00000020, t1 : 00000000 500099E1, t2 : 00000000 500081E0, t3 : FFFFFFFF FFFFFFF2
    t4 : 00000000 0000000E, t5 : 00000000 00000000, t6 : 00000000 0D95F890, t7 : 00000000 000001FF
    s0 : 00000000 00000000, s1 : 00000000 2A2FDB40, s2 : FFFFFFFF FFFFFFEC, s3 : 00000000 3080C980
    s4 : 00000000 0D95F89E, s5 : 00000000 2A300EE0, s6 : 00000000 00000000, s7 : 00000000 0000000E
    t8 : 00000000 000007FC, t9 : 00000000 2A300200, k0 : 00000000 00000000, k1 : 00000000 00000000
    gp : 00000000 29133C00, sp : 00000000 3022FBB8, s8 : 00000000 00000054, ra : 00000000 22768424
    EPC : 22768478, ErrorEPC : 80412AB4, SREG : 500099E3
    MDLO : 87126668, MDHI : D990ADBB, BadVaddr : 00000014
    CacheErr_Icache : 0x007F7F00 - 000040D8, CacheErr_Dcache : 0x00000000 - 00001FA0
    TagLo_Icache : 0x00000000 - 23642303, DataLo_Icache : 0xAFBF0018 - 0D81ADDB
    DataHi_Icache: 0x00000000 - 00000001
    TagLo_Dcache : 0x00000000 - 2277E583, TagHi_Dcache : 0x00000000 - 0912BD81
    DataLo_Dcache: 0x00000001 - 2368110C, DataHi_Dcache : 0x00000000 - 0000001C
    TEXT_START : 0x21003178
    DATA_START : 0x260888A0
    Cause 0000040C (Code 0x3): TLB (store) exception
    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z

    === Flushing messages (22:02:12 UTC Thu Oct 28 2010) ===
    Buffered messages:
    *Oct 28 20:52:40.075: %LINK-3-UPDOWN: Interface SM1/0, changed state to up
    *Oct 28 20:52:42.195: %LINK-3-UPDOWN: Interface GigabitEthernet0/0, changed state to up
    *Oct 28 20:52:42.195: %LINK-3-UPDOWN: Interface GigabitEthernet0/1, changed state to down
    *Oct 28 20:52:42.195: %LINK-3-UPDOWN: Interface GigabitEthernet0/2, changed state to down
    *Oct 28 20:52:44.631: %LINK-3-UPDOWN: Interface SM1/1, changed state to up
    *Oct 28 20:53:01.655: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/0, changed state to up
    *Oct 28 20:53:01.923: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/1, changed state to up
    *Oct 28 20:53:02.075: %LINK-3-UPDOWN: Interface Foreign Exchange Station 0/1/0, changed state to up
    *Oct 28 20:53:02.075: %LINK-3-UPDOWN: Interface Foreign Exchange Station 0/1/1, changed state to up
    *Oct 28 20:53:43.739: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/0, changed state to operational status down due to cable removal
    *Oct 28 20:53:44.739: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/1, changed state to operational status down due to cable removal
    Queued messages:
    No warm reboot Storage
    *** System received a Bus Error exception ***
    signal= 0xa, code= 0x40c, context= 0x29726b74
    PC = 0x22768478, SP = 0x3022fbb8, RA = 0x22768424
    Cause Reg = 0x0000040c, Status Reg = 0x500099e3
    System Bootstrap, Version 15.0(1r)M6, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 2010 by cisco Systems, Inc.
    Total memory size = 512 MB - On-board = 512 MB, DIMM0 = 0 MB
    CISCO2911/K9 platform with 524288 Kbytes of main memory
    Main memory is configured to 72/-1(On-board/DIMM0) bit mode with ECC enabled

    Readonly ROMMON initialized
    program load complete, entry point: 0x80803000, size: 0x1b340

    IOS Image Load Test
    ___________________
    Digitally Signed Development Software
    program load complete, entry point: 0x81000000, size: 0x40b6b74
    Self decompressing the image : #############################################################################################################

    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2691036>
    or simply reply to this email.
    -- --
    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2691978>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2699015>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2699042>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2699089>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2699640>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2704890>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2703353>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2708817>
    or simply reply to this email.

    Subject: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-
    Replied by: Ken Romo on 20-11-2010 01:34:37 AM
    Radhika,
     
    Do you know if the IOS team has been able to reproduce this yet?
     
    Thanks in advance,
     
    Ken Romo
     
    Ken,

    The IOS team is trying to reproduce this in their setup. I will let you know what the finding are or if we need a debug session with you (if they can¿t reproduce in their setup)



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Wednesday, November 03, 2010 9:03 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    Anything new here today?

    Thanks again,

    Ken



    Ken,

    Right now it looks an IOS bug but we need to reproduce this in house so we can confirm for sure. I will keep you in the loop on what we find. If it turns out to be an issue with this particular PVDM I will let you know.



    Appreciate all your help with this.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Tuesday, November 02, 2010 9:51 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    So what is the root cause?

    The IOS or the PVDMS?

    Do I need to RMA my PVDMS?

    Let me know thank you.

    Ken


    Ken,

    Thanks for the information. We will check internally if this has been tested. I will cancel the debug session for today since we most likely have the root cause for the issue. We will try to reproduce this internally and if we need further information from you will setup a different session.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Tuesday, November 02, 2010 8:49 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    The PVDMS is:

    PVDM3-16 V01
    S/N FOC14200FNK

    Is this what you were looking for?

    Ken


    Ken,

    I am not sure if it is the PVDM that is bad but it could be a bug in the IOS image also where you have pvdm and the SRE module it could be some issue. For now can you continute to do beta for SRE-v without the PVDMS.



    I will check with the team and get back to you as to how to proceed.



    Can you let me know what PVDM models you have so we can try to reproduce this in our lab.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Monday, November 01, 2010 3:59 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    I pulled the PVDM and it is working.

    Does this mean the PVDM is bad?

    Ken


    Ken,

    Please try out the new image sent by Brett to you when you get a chance. Also one difference we noticed is that you have PVDM¿s in your setup that we don not have in our test setup. Would it be possible to remove the PVDMS temporarily and try the ping? This may help us root cause the issue.



    I will also schedule a WebEx for tomorrow morning 10:30 PST with the IOS developer so we can take a look if the change of IOS image and removal of PVDM¿s does not solve the issue. Please let me know if that time slot does not work for you.



    Thanks,

    Radhika





    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Monday, November 01, 2010 11:19 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    Here you go:

    boxer#show vlan-switch
    VLAN Name Status Ports
    ---- -------------------------------- --------- -------------------------------
    1 default active
    1002 fddi-default act/unsup
    1003 token-ring-default act/unsup
    1004 fddinet-default act/unsup
    1005 trnet-default act/unsup
    VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2
    ---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------
    1 enet 100001 1500 - - - - - 1002 1003
    1002 fddi 101002 1500 - - - - - 1 1003
    1003 tr 101003 1500 1005 0 - - srb 1 1002
    1004 fdnet 101004 1500 - - 1 ibm - 0 0
    1005 trnet 101005 1500 - - 1 ibm - 0 0


    boxer#sh platform mgf module
    Registered Module Information
    Code: NR - Not Registered, TM - Trust Mode, SP - Scheduling Profile
    BL - Buffer Level, TR - Traffic Rate, PT - Pause Threshold
    slot vlan type/ID TM SP BL TR PT
    ---- ---- ---------- ------- --- ------ ----- ----
    ISM NR
    EHWIC-0 NR
    EHWIC-1 NR
    EHWIC-2 NR
    EHWIC-3 NR
    PVDM-0 2 PVDM/5 UP 1 low 1000 low
    PVDM-1 2 PVDM/5 UP 1 low 1000 low
    SM-1 1 Switch/3 UP 1 low 1000 high




    Thanks Ken. Can you also give us the output of the following.



    1) show vlan-switch

    2) ¿show platform mgf module¿ before the crash happens.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Monday, November 01, 2010 10:50 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    I will try whatever you suggest, just let me know when you have posted the new IOS.

    Below is my config:

    boxer#sh run
    Building configuration...

    Current configuration : 5777 bytes
    !
    version 15.1
    service timestamps debug datetime msec
    service timestamps log datetime msec
    no service password-encryption
    !
    hostname boxer
    !
    boot-start-marker
    boot system flash0 c2900-universalk9-mz.SSA.151-2.19.T
    boot-end-marker
    !
    !
    logging buffered 51200 warnings
    !
    no aaa new-model
    !
    no ipv6 cef
    ip source-route
    ip cef
    !
    !
    !
    !
    !
    ip domain name yourdomain.com
    multilink bundle-name authenticated
    !
    !
    !
    !
    !
    crypto pki token default removal timeout 0
    !
    crypto pki trustpoint TP-self-signed-1999750280
    enrollment selfsigned
    subject-name cn=IOS-Self-Signed-Certificate-1999750280
    revocation-check none
    rsakeypair TP-self-signed-1999750280
    !
    !
    crypto pki certificate chain TP-self-signed-1999750280
    certificate self-signed 01
    3082024C 308201B5 A0030201 02020101 300D0609 2A864886 F70D0101 04050030
    31312F30 2D060355 04031326 494F532D 53656C66 2D536967 6E65642D 43657274
    69666963 6174652D 31393939 37353032 3830301E 170D3130 31303230 32323335
    32365A17 0D323030 31303130 30303030 305A3031 312F302D 06035504 03132649
    4F532D53 656C662D 5369676E 65642D43 65727469 66696361 74652D31 39393937
    35303238 3030819F 300D0609 2A864886 F70D0101 01050003 818D0030 81890281
    81009378 2E139D79 DCA59865 14AB3398 870362B7 40BB9C13 A5DC5315 6108DF92
    5E78CF06 A40D4DB5 B66D410E FAFE75AC 764997B1 5C551A47 CFA00109 520352EC
    33A69E24 B3C1175B 136FC62A 8BE4637E B834059B FC7CAA6E 957DA0BB 66D8DC49
    80F82890 981FFCFE 0DC7E6F9 53287989 3887C5F6 AF59D0BE B502E11E FD16F556
    DBB90203 010001A3 74307230 0F060355 1D130101 FF040530 030101FF 301F0603
    551D1104 18301682 14626F78 65722E79 6F757264 6F6D6169 6E2E636F 6D301F06
    03551D23 04183016 80143541 7934E424 4B9A60DB E6C908C3 C20BAA17 D058301D
    0603551D 0E041604 14354179 34E4244B 9A60DBE6 C908C3C2 0BAA17D0 58300D06
    092A8648 86F70D01 01040500 03818100 3D222AB5 177D452F 153DCA26 1D7ECB49
    58BCBF60 DA18DC04 94B82EA3 76884EBC D7131641 08687C04 6C6645DF 78B2D2F8
    409BCAD7 50AF5091 B99614FD C2424D89 407A9109 BCA20473 F4CE33D4 4B126483
    C240C0B9 7A628E53 E419FEC3 B8853671 03113F5E 47FA8120 9F9A7A9D 11498FE0
    82C96578 8FD9770A EBD27F73 DF2E1487
    quit
    voice-card 0
    !
    !
    !
    !
    !
    !
    !
    license udi pid CISCO2911/K9 sn FTX1422A077
    hw-module pvdm 0/0
    !
    hw-module sm 1
    !
    !
    !
    username jack privilege 15 secret 5 $1$c5QR$fYGTbhWRKsBZ1JpNyIQGG1
    username marco privilege 15 secret 5 $1$amqq$5pI0T7mUViDL5Y.NqX/yz.
    !
    redundancy
    !
    !
    !
    !
    !
    !
    interface GigabitEthernet0/0
    description To tusqa network
    ip address 172.17.17.130 255.255.248.0
    duplex auto
    speed auto
    !
    interface GigabitEthernet0/1
    no ip address
    shutdown
    duplex auto
    speed auto
    !
    interface GigabitEthernet0/2
    no ip address
    shutdown
    duplex auto
    speed auto
    !
    interface SM1/0
    ip unnumbered GigabitEthernet0/0
    service-module ip address 172.17.17.129 255.255.248.0
    !Application: SRE-V Running on SMV
    service-module ip default-gateway 172.17.17.130
    service-module mgf ip address 10.62.64.1 255.255.255.0
    service-module mgf ip default-gateway 10.62.64.2
    !
    interface SM1/1
    description Internal switch interface connected to Service Module
    switchport mode trunk
    !
    interface Vlan1
    ip address 10.62.64.2 255.255.255.0
    !
    ip forward-protocol nd
    !
    ip http server
    ip http access-class 23
    ip http authentication local
    ip http secure-server
    ip http timeout-policy idle 60 life 86400 requests 10000
    !
    ip route 172.17.17.129 255.255.255.255 SM1/0
    !
    !
    !
    !
    control-plane
    !
    !
    voice-port 0/0/0
    !
    voice-port 0/0/1
    !
    voice-port 0/1/0
    !
    voice-port 0/1/1
    !
    !
    !
    mgcp profile default
    !
    !
    !
    !
    !
    gatekeeper
    shutdown
    !
    !
    banner exec ^C
    % Password expiration warning.
    -----------------------------------------------------------------------
    Cisco Configuration Professional (Cisco CP) is installed on this device
    and it provides the default username "cisco" for one-time use. If you have
    already used the username "cisco" to login to the router and your IOS image
    supports the "one-time" user option, then this username has already expired.
    You will not be able to login to the router with this username after you exit
    this session.
    It is strongly suggested that you create a new username with a privilege level
    of 15 using the following command.
    username <myuser> privilege 15 secret 0 <mypassword>
    Replace <myuser> and <mypassword> with the username and password you want to
    use.
    -----------------------------------------------------------------------
    ^C
    banner login ^C
    -----------------------------------------------------------------------
    Cisco Configuration Professional (Cisco CP) is installed on this device.
    This feature requires the one-time use of the username "cisco" with the
    password "cisco". These default credentials have a privilege level of 15.
    YOU MUST USE CISCO CP or the CISCO IOS CLI TO CHANGE THESE PUBLICLY-KNOWN
    CREDENTIALS
    Here are the Cisco IOS commands.
    username <myuser> privilege 15 secret 0 <mypassword>
    no username cisco
    Replace <myuser> and <mypassword> with the username and password you want
    to use.
    IF YOU DO NOT CHANGE THE PUBLICLY-KNOWN CREDENTIALS, YOU WILL NOT BE ABLE
    TO LOG INTO THE DEVICE AGAIN AFTER YOU HAVE LOGGED OFF.
    For more information about Cisco CP please follow the instructions in the
    QUICK START GUIDE for your router or go to http://www.cisco.com/go/ciscocp
    -----------------------------------------------------------------------
    ^C
    !
    line con 0
    login local
    line aux 0
    line 67
    no activation-character
    no exec
    transport preferred none
    transport input all
    transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
    stopbits 1
    flowcontrol software
    line vty 0 4
    privilege level 15
    login local
    transport input telnet
    line vty 5 15
    privilege level 15
    login local
    transport input telnet ssh
    !
    exception data-corruption buffer truncate
    scheduler allocate 20000 1000
    end



    Ken, Thanks for trying out the image for us. We are trying to reproduce this on our end but have had no luck so far. Can you please send us the output of show running-config from your router.



    Also we have one more image that we would like you to try it out before the debusg session would that be ok?



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Monday, November 01, 2010 10:22 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------

    Radhika,

    I tried the new OS and still getting same IOS crash.
    As mentioned I will work around your schedule so let me if you were able to get someone from the IOS team to help troubleshoot today.

    Thanks in advance,

    Ken Romo


    Ken,

    I am trying to get some help from the IOS team since this a router crash. So I will setup the webex session to debug for some time Monday so we can collect all the information and try out any suggestion from them.



    For Now We will post a newer IOS image to the beta Site and can you give that a try to see if that will solve the issue.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Friday, October 29, 2010 8:24 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    I will work around your schedule, anytime you are available, I will make myself available.
    email:
    kromo@opentext.com

    Thanks in advance,

    Ken Romo

    +++++++++++++++++++++++++++++++++

    Ken,

    Would a webex session tomorrow morning (any time between 10:00 and 1:00) work for you? Let me know the time that would work for you and also your email address so I can send you a webex invite.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Thursday, October 28, 2010 3:12 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Radhika Miriyala in Service Ready Engine Virtualizatio



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    No worries, we are trying to work this out together and I appreciate the help.
    s/m 1/1 is set as trunk but I went ahead and reconfigured to truank again and reloaded OS and get the same crash when I ping to the MGF interface from the SRE (I attached the errors at the bottom of this message).

    Ken,

    Sorry I just realized the mistake. I meant to say make the interface sm 1/1 as trunk.

    Sorry about the confusion.



    Please try it out.



    Thanks,

    Radhika



    boxer#
    %ALIGN-1-FATAL: Illegal access to a low address 22:02:10 UTC Thu Oct 28 2010
    addr=0x14, pc=0x22765BD8z , ra=0x22765B84z , sp=0x3022FBB8
    %ALIGN-1-FATAL: Illegal access to a low address 22:02:11 UTC Thu Oct 28 2010
    addr=0x14, pc=0x22765BD8z , ra=0x22765B84z , sp=0x3022FBB8

    22:02:11 UTC Thu Oct 28 2010: TLB (store) exception, CPU signal 10, PC = 0x22768478

    --------------------------------------------------------------------
    Possible software fault. Upon reccurence, please collect
    crashinfo, "show tech" and contact Cisco Technical Support.
    --------------------------------------------------------------------

    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z
    $0 : 00000000 00000000, AT : 00000000 29130000, v0 : 00000000 00000001, v1 : 00000000 0D8B8540
    a0 : 00000000 00000000, a1 : 00000000 0D8B8584, a2 : 00000000 2A2F8ABC, a3 : 00000000 00000004
    t0 : 00000000 00000020, t1 : 00000000 500099E1, t2 : 00000000 500081E0, t3 : FFFFFFFF FFFFFFF2
    t4 : 00000000 0000000E, t5 : 00000000 00000000, t6 : 00000000 0D95F890, t7 : 00000000 000001FF
    s0 : 00000000 00000000, s1 : 00000000 2A2FDB40, s2 : FFFFFFFF FFFFFFEC, s3 : 00000000 3080C980
    s4 : 00000000 0D95F89E, s5 : 00000000 2A300EE0, s6 : 00000000 00000000, s7 : 00000000 0000000E
    t8 : 00000000 000007FC, t9 : 00000000 2A300200, k0 : 00000000 00000000, k1 : 00000000 00000000
    gp : 00000000 29133C00, sp : 00000000 3022FBB8, s8 : 00000000 00000054, ra : 00000000 22768424
    EPC : 22768478, ErrorEPC : 80412AB4, SREG : 500099E3
    MDLO : 87126668, MDHI : D990ADBB, BadVaddr : 00000014
    CacheErr_Icache : 0x007F7F00 - 000040D8, CacheErr_Dcache : 0x00000000 - 00001FA0
    TagLo_Icache : 0x00000000 - 23642303, DataLo_Icache : 0xAFBF0018 - 0D81ADDB
    DataHi_Icache: 0x00000000 - 00000001
    TagLo_Dcache : 0x00000000 - 2277E583, TagHi_Dcache : 0x00000000 - 0912BD81
    DataLo_Dcache: 0x00000001 - 2368110C, DataHi_Dcache : 0x00000000 - 0000001C
    TEXT_START : 0x21003178
    DATA_START : 0x260888A0
    Cause 0000040C (Code 0x3): TLB (store) exception

    22:02:11 UTC Thu Oct 28 2010: TLB (store) exception, CPU signal 10, PC = 0x22768478

    --------------------------------------------------------------------
    Possible software fault. Upon reccurence, please collect
    crashinfo, "show tech" and contact Cisco Technical Support.
    --------------------------------------------------------------------

    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z
    $0 : 00000000 00000000, AT : 00000000 29130000, v0 : 00000000 00000001, v1 : 00000000 0D8B8540
    a0 : 00000000 00000000, a1 : 00000000 0D8B8584, a2 : 00000000 2A2F8ABC, a3 : 00000000 00000004
    t0 : 00000000 00000020, t1 : 00000000 500099E1, t2 : 00000000 500081E0, t3 : FFFFFFFF FFFFFFF2
    t4 : 00000000 0000000E, t5 : 00000000 00000000, t6 : 00000000 0D95F890, t7 : 00000000 000001FF
    s0 : 00000000 00000000, s1 : 00000000 2A2FDB40, s2 : FFFFFFFF FFFFFFEC, s3 : 00000000 3080C980
    s4 : 00000000 0D95F89E, s5 : 00000000 2A300EE0, s6 : 00000000 00000000, s7 : 00000000 0000000E
    t8 : 00000000 000007FC, t9 : 00000000 2A300200, k0 : 00000000 00000000, k1 : 00000000 00000000
    gp : 00000000 29133C00, sp : 00000000 3022FBB8, s8 : 00000000 00000054, ra : 00000000 22768424
    EPC : 22768478, ErrorEPC : 80412AB4, SREG : 500099E3
    MDLO : 87126668, MDHI : D990ADBB, BadVaddr : 00000014
    CacheErr_Icache : 0x007F7F00 - 000040D8, CacheErr_Dcache : 0x00000000 - 00001FA0
    TagLo_Icache : 0x00000000 - 23642303, DataLo_Icache : 0xAFBF0018 - 0D81ADDB
    DataHi_Icache: 0x00000000 - 00000001
    TagLo_Dcache : 0x00000000 - 2277E583, TagHi_Dcache : 0x00000000 - 0912BD81
    DataLo_Dcache: 0x00000001 - 2368110C, DataHi_Dcache : 0x00000000 - 0000001C
    TEXT_START : 0x21003178
    DATA_START : 0x260888A0
    Cause 0000040C (Code 0x3): TLB (store) exception
    Writing crashinfo to flash:crashinfo_20101028-220211-UTC
    22:02:11 UTC Thu Oct 28 2010: TLB (store) exception, CPU signal 10, PC = 0x22768478

    --------------------------------------------------------------------
    Possible software fault. Upon reccurence, please collect
    crashinfo, "show tech" and contact Cisco Technical Support.
    --------------------------------------------------------------------

    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z
    $0 : 00000000 00000000, AT : 00000000 29130000, v0 : 00000000 00000001, v1 : 00000000 0D8B8540
    a0 : 00000000 00000000, a1 : 00000000 0D8B8584, a2 : 00000000 2A2F8ABC, a3 : 00000000 00000004
    t0 : 00000000 00000020, t1 : 00000000 500099E1, t2 : 00000000 500081E0, t3 : FFFFFFFF FFFFFFF2
    t4 : 00000000 0000000E, t5 : 00000000 00000000, t6 : 00000000 0D95F890, t7 : 00000000 000001FF
    s0 : 00000000 00000000, s1 : 00000000 2A2FDB40, s2 : FFFFFFFF FFFFFFEC, s3 : 00000000 3080C980
    s4 : 00000000 0D95F89E, s5 : 00000000 2A300EE0, s6 : 00000000 00000000, s7 : 00000000 0000000E
    t8 : 00000000 000007FC, t9 : 00000000 2A300200, k0 : 00000000 00000000, k1 : 00000000 00000000
    gp : 00000000 29133C00, sp : 00000000 3022FBB8, s8 : 00000000 00000054, ra : 00000000 22768424
    EPC : 22768478, ErrorEPC : 80412AB4, SREG : 500099E3
    MDLO : 87126668, MDHI : D990ADBB, BadVaddr : 00000014
    CacheErr_Icache : 0x007F7F00 - 000040D8, CacheErr_Dcache : 0x00000000 - 00001FA0
    TagLo_Icache : 0x00000000 - 23642303, DataLo_Icache : 0xAFBF0018 - 0D81ADDB
    DataHi_Icache: 0x00000000 - 00000001
    TagLo_Dcache : 0x00000000 - 2277E583, TagHi_Dcache : 0x00000000 - 0912BD81
    DataLo_Dcache: 0x00000001 - 2368110C, DataHi_Dcache : 0x00000000 - 0000001C
    TEXT_START : 0x21003178
    DATA_START : 0x260888A0
    Cause 0000040C (Code 0x3): TLB (store) exception
    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z

    === Flushing messages (22:02:12 UTC Thu Oct 28 2010) ===
    Buffered messages:
    *Oct 28 20:52:40.075: %LINK-3-UPDOWN: Interface SM1/0, changed state to up
    *Oct 28 20:52:42.195: %LINK-3-UPDOWN: Interface GigabitEthernet0/0, changed state to up
    *Oct 28 20:52:42.195: %LINK-3-UPDOWN: Interface GigabitEthernet0/1, changed state to down
    *Oct 28 20:52:42.195: %LINK-3-UPDOWN: Interface GigabitEthernet0/2, changed state to down
    *Oct 28 20:52:44.631: %LINK-3-UPDOWN: Interface SM1/1, changed state to up
    *Oct 28 20:53:01.655: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/0, changed state to up
    *Oct 28 20:53:01.923: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/1, changed state to up
    *Oct 28 20:53:02.075: %LINK-3-UPDOWN: Interface Foreign Exchange Station 0/1/0, changed state to up
    *Oct 28 20:53:02.075: %LINK-3-UPDOWN: Interface Foreign Exchange Station 0/1/1, changed state to up
    *Oct 28 20:53:43.739: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/0, changed state to operational status down due to cable removal
    *Oct 28 20:53:44.739: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/1, changed state to operational status down due to cable removal
    Queued messages:
    No warm reboot Storage
    *** System received a Bus Error exception ***
    signal= 0xa, code= 0x40c, context= 0x29726b74
    PC = 0x22768478, SP = 0x3022fbb8, RA = 0x22768424
    Cause Reg = 0x0000040c, Status Reg = 0x500099e3
    System Bootstrap, Version 15.0(1r)M6, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 2010 by cisco Systems, Inc.
    Total memory size = 512 MB - On-board = 512 MB, DIMM0 = 0 MB
    CISCO2911/K9 platform with 524288 Kbytes of main memory
    Main memory is configured to 72/-1(On-board/DIMM0) bit mode with ECC enabled

    Readonly ROMMON initialized
    program load complete, entry point: 0x80803000, size: 0x1b340

    IOS Image Load Test
    ___________________
    Digitally Signed Development Software
    program load complete, entry point: 0x81000000, size: 0x40b6b74
    Self decompressing the image : #############################################################################################################

    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2691036>
    or simply reply to this email.
    -- --
    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2691978>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2699015>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2699042>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2699089>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2699640>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2704890>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2703353>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2708817>
    or simply reply to this email.


    Subject: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-
    Replied by: Radhika Miriyala on 20-11-2010 01:34:38 AM
    Ken,

    Yes the IOS team was able to reproduce it. They are working on fixing the issue.  Also one quick question the IOS team wanted to know was if the have used the PVDM successfully before the using sre-v.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Thursday, November 04, 2010 9:45 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    Do you know if the IOS team has been able to reproduce this yet?

    Thanks in advance,

    Ken Romo


    Ken,

    The IOS team is trying to reproduce this in their setup. I will let you know what the finding are or if we need a debug session with you (if they can¿t reproduce in their setup)



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Wednesday, November 03, 2010 9:03 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    Anything new here today?

    Thanks again,

    Ken



    Ken,

    Right now it looks an IOS bug but we need to reproduce this in house so we can confirm for sure. I will keep you in the loop on what we find. If it turns out to be an issue with this particular PVDM I will let you know.



    Appreciate all your help with this.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Tuesday, November 02, 2010 9:51 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    So what is the root cause?

    The IOS or the PVDMS?

    Do I need to RMA my PVDMS?

    Let me know thank you.

    Ken


    Ken,

    Thanks for the information. We will check internally if this has been tested. I will cancel the debug session for today since we most likely have the root cause for the issue. We will try to reproduce this internally and if we need further information from you will setup a different session.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Tuesday, November 02, 2010 8:49 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    The PVDMS is:

    PVDM3-16 V01
    S/N FOC14200FNK

    Is this what you were looking for?

    Ken


    Ken,

    I am not sure if it is the PVDM that is bad but it could be a bug in the IOS image also where you have pvdm and the SRE module it could be some issue. For now can you continute to do beta for SRE-v without the PVDMS.



    I will check with the team and get back to you as to how to proceed.



    Can you let me know what PVDM models you have so we can try to reproduce this in our lab.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Monday, November 01, 2010 3:59 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    I pulled the PVDM and it is working.

    Does this mean the PVDM is bad?

    Ken


    Ken,

    Please try out the new image sent by Brett to you when you get a chance. Also one difference we noticed is that you have PVDM¿s in your setup that we don not have in our test setup. Would it be possible to remove the PVDMS temporarily and try the ping? This may help us root cause the issue.



    I will also schedule a WebEx for tomorrow morning 10:30 PST with the IOS developer so we can take a look if the change of IOS image and removal of PVDM¿s does not solve the issue. Please let me know if that time slot does not work for you.



    Thanks,

    Radhika





    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Monday, November 01, 2010 11:19 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    Here you go:

    boxer#show vlan-switch
    VLAN Name Status Ports
    ---- -------------------------------- --------- -------------------------------
    1 default active
    1002 fddi-default act/unsup
    1003 token-ring-default act/unsup
    1004 fddinet-default act/unsup
    1005 trnet-default act/unsup
    VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2
    ---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------
    1 enet 100001 1500 - - - - - 1002 1003
    1002 fddi 101002 1500 - - - - - 1 1003
    1003 tr 101003 1500 1005 0 - - srb 1 1002
    1004 fdnet 101004 1500 - - 1 ibm - 0 0
    1005 trnet 101005 1500 - - 1 ibm - 0 0


    boxer#sh platform mgf module
    Registered Module Information
    Code: NR - Not Registered, TM - Trust Mode, SP - Scheduling Profile
    BL - Buffer Level, TR - Traffic Rate, PT - Pause Threshold
    slot vlan type/ID TM SP BL TR PT
    ---- ---- ---------- ------- --- ------ ----- ----
    ISM NR
    EHWIC-0 NR
    EHWIC-1 NR
    EHWIC-2 NR
    EHWIC-3 NR
    PVDM-0 2 PVDM/5 UP 1 low 1000 low
    PVDM-1 2 PVDM/5 UP 1 low 1000 low
    SM-1 1 Switch/3 UP 1 low 1000 high




    Thanks Ken. Can you also give us the output of the following.



    1) show vlan-switch

    2) ¿show platform mgf module¿ before the crash happens.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Monday, November 01, 2010 10:50 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    I will try whatever you suggest, just let me know when you have posted the new IOS.

    Below is my config:

    boxer#sh run
    Building configuration...

    Current configuration : 5777 bytes
    !
    version 15.1
    service timestamps debug datetime msec
    service timestamps log datetime msec
    no service password-encryption
    !
    hostname boxer
    !
    boot-start-marker
    boot system flash0 c2900-universalk9-mz.SSA.151-2.19.T
    boot-end-marker
    !
    !
    logging buffered 51200 warnings
    !
    no aaa new-model
    !
    no ipv6 cef
    ip source-route
    ip cef
    !
    !
    !
    !
    !
    ip domain name yourdomain.com
    multilink bundle-name authenticated
    !
    !
    !
    !
    !
    crypto pki token default removal timeout 0
    !
    crypto pki trustpoint TP-self-signed-1999750280
    enrollment selfsigned
    subject-name cn=IOS-Self-Signed-Certificate-1999750280
    revocation-check none
    rsakeypair TP-self-signed-1999750280
    !
    !
    crypto pki certificate chain TP-self-signed-1999750280
    certificate self-signed 01
    3082024C 308201B5 A0030201 02020101 300D0609 2A864886 F70D0101 04050030
    31312F30 2D060355 04031326 494F532D 53656C66 2D536967 6E65642D 43657274
    69666963 6174652D 31393939 37353032 3830301E 170D3130 31303230 32323335
    32365A17 0D323030 31303130 30303030 305A3031 312F302D 06035504 03132649
    4F532D53 656C662D 5369676E 65642D43 65727469 66696361 74652D31 39393937
    35303238 3030819F 300D0609 2A864886 F70D0101 01050003 818D0030 81890281
    81009378 2E139D79 DCA59865 14AB3398 870362B7 40BB9C13 A5DC5315 6108DF92
    5E78CF06 A40D4DB5 B66D410E FAFE75AC 764997B1 5C551A47 CFA00109 520352EC
    33A69E24 B3C1175B 136FC62A 8BE4637E B834059B FC7CAA6E 957DA0BB 66D8DC49
    80F82890 981FFCFE 0DC7E6F9 53287989 3887C5F6 AF59D0BE B502E11E FD16F556
    DBB90203 010001A3 74307230 0F060355 1D130101 FF040530 030101FF 301F0603
    551D1104 18301682 14626F78 65722E79 6F757264 6F6D6169 6E2E636F 6D301F06
    03551D23 04183016 80143541 7934E424 4B9A60DB E6C908C3 C20BAA17 D058301D
    0603551D 0E041604 14354179 34E4244B 9A60DBE6 C908C3C2 0BAA17D0 58300D06
    092A8648 86F70D01 01040500 03818100 3D222AB5 177D452F 153DCA26 1D7ECB49
    58BCBF60 DA18DC04 94B82EA3 76884EBC D7131641 08687C04 6C6645DF 78B2D2F8
    409BCAD7 50AF5091 B99614FD C2424D89 407A9109 BCA20473 F4CE33D4 4B126483
    C240C0B9 7A628E53 E419FEC3 B8853671 03113F5E 47FA8120 9F9A7A9D 11498FE0
    82C96578 8FD9770A EBD27F73 DF2E1487
    quit
    voice-card 0
    !
    !
    !
    !
    !
    !
    !
    license udi pid CISCO2911/K9 sn FTX1422A077
    hw-module pvdm 0/0
    !
    hw-module sm 1
    !
    !
    !
    username jack privilege 15 secret 5 $1$c5QR$fYGTbhWRKsBZ1JpNyIQGG1
    username marco privilege 15 secret 5 $1$amqq$5pI0T7mUViDL5Y.NqX/yz.
    !
    redundancy
    !
    !
    !
    !
    !
    !
    interface GigabitEthernet0/0
    description To tusqa network
    ip address 172.17.17.130 255.255.248.0
    duplex auto
    speed auto
    !
    interface GigabitEthernet0/1
    no ip address
    shutdown
    duplex auto
    speed auto
    !
    interface GigabitEthernet0/2
    no ip address
    shutdown
    duplex auto
    speed auto
    !
    interface SM1/0
    ip unnumbered GigabitEthernet0/0
    service-module ip address 172.17.17.129 255.255.248.0
    !Application: SRE-V Running on SMV
    service-module ip default-gateway 172.17.17.130
    service-module mgf ip address 10.62.64.1 255.255.255.0
    service-module mgf ip default-gateway 10.62.64.2
    !
    interface SM1/1
    description Internal switch interface connected to Service Module
    switchport mode trunk
    !
    interface Vlan1
    ip address 10.62.64.2 255.255.255.0
    !
    ip forward-protocol nd
    !
    ip http server
    ip http access-class 23
    ip http authentication local
    ip http secure-server
    ip http timeout-policy idle 60 life 86400 requests 10000
    !
    ip route 172.17.17.129 255.255.255.255 SM1/0
    !
    !
    !
    !
    control-plane
    !
    !
    voice-port 0/0/0
    !
    voice-port 0/0/1
    !
    voice-port 0/1/0
    !
    voice-port 0/1/1
    !
    !
    !
    mgcp profile default
    !
    !
    !
    !
    !
    gatekeeper
    shutdown
    !
    !
    banner exec ^C
    % Password expiration warning.
    -----------------------------------------------------------------------
    Cisco Configuration Professional (Cisco CP) is installed on this device
    and it provides the default username "cisco" for one-time use. If you have
    already used the username "cisco" to login to the router and your IOS image
    supports the "one-time" user option, then this username has already expired.
    You will not be able to login to the router with this username after you exit
    this session.
    It is strongly suggested that you create a new username with a privilege level
    of 15 using the following command.
    username <myuser> privilege 15 secret 0 <mypassword>
    Replace <myuser> and <mypassword> with the username and password you want to
    use.
    -----------------------------------------------------------------------
    ^C
    banner login ^C
    -----------------------------------------------------------------------
    Cisco Configuration Professional (Cisco CP) is installed on this device.
    This feature requires the one-time use of the username "cisco" with the
    password "cisco". These default credentials have a privilege level of 15.
    YOU MUST USE CISCO CP or the CISCO IOS CLI TO CHANGE THESE PUBLICLY-KNOWN
    CREDENTIALS
    Here are the Cisco IOS commands.
    username <myuser> privilege 15 secret 0 <mypassword>
    no username cisco
    Replace <myuser> and <mypassword> with the username and password you want
    to use.
    IF YOU DO NOT CHANGE THE PUBLICLY-KNOWN CREDENTIALS, YOU WILL NOT BE ABLE
    TO LOG INTO THE DEVICE AGAIN AFTER YOU HAVE LOGGED OFF.
    For more information about Cisco CP please follow the instructions in the
    QUICK START GUIDE for your router or go to http://www.cisco.com/go/ciscocp
    -----------------------------------------------------------------------
    ^C
    !
    line con 0
    login local
    line aux 0
    line 67
    no activation-character
    no exec
    transport preferred none
    transport input all
    transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
    stopbits 1
    flowcontrol software
    line vty 0 4
    privilege level 15
    login local
    transport input telnet
    line vty 5 15
    privilege level 15
    login local
    transport input telnet ssh
    !
    exception data-corruption buffer truncate
    scheduler allocate 20000 1000
    end



    Ken, Thanks for trying out the image for us. We are trying to reproduce this on our end but have had no luck so far. Can you please send us the output of show running-config from your router.



    Also we have one more image that we would like you to try it out before the debusg session would that be ok?



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Monday, November 01, 2010 10:22 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------

    Radhika,

    I tried the new OS and still getting same IOS crash.
    As mentioned I will work around your schedule so let me if you were able to get someone from the IOS team to help troubleshoot today.

    Thanks in advance,

    Ken Romo


    Ken,

    I am trying to get some help from the IOS team since this a router crash. So I will setup the webex session to debug for some time Monday so we can collect all the information and try out any suggestion from them.



    For Now We will post a newer IOS image to the beta Site and can you give that a try to see if that will solve the issue.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Friday, October 29, 2010 8:24 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    I will work around your schedule, anytime you are available, I will make myself available.
    email:
    kromo@opentext.com

    Thanks in advance,

    Ken Romo

    +++++++++++++++++++++++++++++++++

    Ken,

    Would a webex session tomorrow morning (any time between 10:00 and 1:00) work for you? Let me know the time that would work for you and also your email address so I can send you a webex invite.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Thursday, October 28, 2010 3:12 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Radhika Miriyala in Service Ready Engine Virtualizatio



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    No worries, we are trying to work this out together and I appreciate the help.
    s/m 1/1 is set as trunk but I went ahead and reconfigured to truank again and reloaded OS and get the same crash when I ping to the MGF interface from the SRE (I attached the errors at the bottom of this message).

    Ken,

    Sorry I just realized the mistake. I meant to say make the interface sm 1/1 as trunk.

    Sorry about the confusion.



    Please try it out.



    Thanks,

    Radhika



    boxer#
    %ALIGN-1-FATAL: Illegal access to a low address 22:02:10 UTC Thu Oct 28 2010
    addr=0x14, pc=0x22765BD8z , ra=0x22765B84z , sp=0x3022FBB8
    %ALIGN-1-FATAL: Illegal access to a low address 22:02:11 UTC Thu Oct 28 2010
    addr=0x14, pc=0x22765BD8z , ra=0x22765B84z , sp=0x3022FBB8

    22:02:11 UTC Thu Oct 28 2010: TLB (store) exception, CPU signal 10, PC = 0x22768478

    --------------------------------------------------------------------
    Possible software fault. Upon reccurence, please collect
    crashinfo, "show tech" and contact Cisco Technical Support.
    --------------------------------------------------------------------

    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z
    $0 : 00000000 00000000, AT : 00000000 29130000, v0 : 00000000 00000001, v1 : 00000000 0D8B8540
    a0 : 00000000 00000000, a1 : 00000000 0D8B8584, a2 : 00000000 2A2F8ABC, a3 : 00000000 00000004
    t0 : 00000000 00000020, t1 : 00000000 500099E1, t2 : 00000000 500081E0, t3 : FFFFFFFF FFFFFFF2
    t4 : 00000000 0000000E, t5 : 00000000 00000000, t6 : 00000000 0D95F890, t7 : 00000000 000001FF
    s0 : 00000000 00000000, s1 : 00000000 2A2FDB40, s2 : FFFFFFFF FFFFFFEC, s3 : 00000000 3080C980
    s4 : 00000000 0D95F89E, s5 : 00000000 2A300EE0, s6 : 00000000 00000000, s7 : 00000000 0000000E
    t8 : 00000000 000007FC, t9 : 00000000 2A300200, k0 : 00000000 00000000, k1 : 00000000 00000000
    gp : 00000000 29133C00, sp : 00000000 3022FBB8, s8 : 00000000 00000054, ra : 00000000 22768424
    EPC : 22768478, ErrorEPC : 80412AB4, SREG : 500099E3
    MDLO : 87126668, MDHI : D990ADBB, BadVaddr : 00000014
    CacheErr_Icache : 0x007F7F00 - 000040D8, CacheErr_Dcache : 0x00000000 - 00001FA0
    TagLo_Icache : 0x00000000 - 23642303, DataLo_Icache : 0xAFBF0018 - 0D81ADDB
    DataHi_Icache: 0x00000000 - 00000001
    TagLo_Dcache : 0x00000000 - 2277E583, TagHi_Dcache : 0x00000000 - 0912BD81
    DataLo_Dcache: 0x00000001 - 2368110C, DataHi_Dcache : 0x00000000 - 0000001C
    TEXT_START : 0x21003178
    DATA_START : 0x260888A0
    Cause 0000040C (Code 0x3): TLB (store) exception

    22:02:11 UTC Thu Oct 28 2010: TLB (store) exception, CPU signal 10, PC = 0x22768478

    --------------------------------------------------------------------
    Possible software fault. Upon reccurence, please collect
    crashinfo, "show tech" and contact Cisco Technical Support.
    --------------------------------------------------------------------

    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z
    $0 : 00000000 00000000, AT : 00000000 29130000, v0 : 00000000 00000001, v1 : 00000000 0D8B8540
    a0 : 00000000 00000000, a1 : 00000000 0D8B8584, a2 : 00000000 2A2F8ABC, a3 : 00000000 00000004
    t0 : 00000000 00000020, t1 : 00000000 500099E1, t2 : 00000000 500081E0, t3 : FFFFFFFF FFFFFFF2
    t4 : 00000000 0000000E, t5 : 00000000 00000000, t6 : 00000000 0D95F890, t7 : 00000000 000001FF
    s0 : 00000000 00000000, s1 : 00000000 2A2FDB40, s2 : FFFFFFFF FFFFFFEC, s3 : 00000000 3080C980
    s4 : 00000000 0D95F89E, s5 : 00000000 2A300EE0, s6 : 00000000 00000000, s7 : 00000000 0000000E
    t8 : 00000000 000007FC, t9 : 00000000 2A300200, k0 : 00000000 00000000, k1 : 00000000 00000000
    gp : 00000000 29133C00, sp : 00000000 3022FBB8, s8 : 00000000 00000054, ra : 00000000 22768424
    EPC : 22768478, ErrorEPC : 80412AB4, SREG : 500099E3
    MDLO : 87126668, MDHI : D990ADBB, BadVaddr : 00000014
    CacheErr_Icache : 0x007F7F00 - 000040D8, CacheErr_Dcache : 0x00000000 - 00001FA0
    TagLo_Icache : 0x00000000 - 23642303, DataLo_Icache : 0xAFBF0018 - 0D81ADDB
    DataHi_Icache: 0x00000000 - 00000001
    TagLo_Dcache : 0x00000000 - 2277E583, TagHi_Dcache : 0x00000000 - 0912BD81
    DataLo_Dcache: 0x00000001 - 2368110C, DataHi_Dcache : 0x00000000 - 0000001C
    TEXT_START : 0x21003178
    DATA_START : 0x260888A0
    Cause 0000040C (Code 0x3): TLB (store) exception
    Writing crashinfo to flash:crashinfo_20101028-220211-UTC
    22:02:11 UTC Thu Oct 28 2010: TLB (store) exception, CPU signal 10, PC = 0x22768478

    --------------------------------------------------------------------
    Possible software fault. Upon reccurence, please collect
    crashinfo, "show tech" and contact Cisco Technical Support.
    --------------------------------------------------------------------

    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z
    $0 : 00000000 00000000, AT : 00000000 29130000, v0 : 00000000 00000001, v1 : 00000000 0D8B8540
    a0 : 00000000 00000000, a1 : 00000000 0D8B8584, a2 : 00000000 2A2F8ABC, a3 : 00000000 00000004
    t0 : 00000000 00000020, t1 : 00000000 500099E1, t2 : 00000000 500081E0, t3 : FFFFFFFF FFFFFFF2
    t4 : 00000000 0000000E, t5 : 00000000 00000000, t6 : 00000000 0D95F890, t7 : 00000000 000001FF
    s0 : 00000000 00000000, s1 : 00000000 2A2FDB40, s2 : FFFFFFFF FFFFFFEC, s3 : 00000000 3080C980
    s4 : 00000000 0D95F89E, s5 : 00000000 2A300EE0, s6 : 00000000 00000000, s7 : 00000000 0000000E
    t8 : 00000000 000007FC, t9 : 00000000 2A300200, k0 : 00000000 00000000, k1 : 00000000 00000000
    gp : 00000000 29133C00, sp : 00000000 3022FBB8, s8 : 00000000 00000054, ra : 00000000 22768424
    EPC : 22768478, ErrorEPC : 80412AB4, SREG : 500099E3
    MDLO : 87126668, MDHI : D990ADBB, BadVaddr : 00000014
    CacheErr_Icache : 0x007F7F00 - 000040D8, CacheErr_Dcache : 0x00000000 - 00001FA0
    TagLo_Icache : 0x00000000 - 23642303, DataLo_Icache : 0xAFBF0018 - 0D81ADDB
    DataHi_Icache: 0x00000000 - 00000001
    TagLo_Dcache : 0x00000000 - 2277E583, TagHi_Dcache : 0x00000000 - 0912BD81
    DataLo_Dcache: 0x00000001 - 2368110C, DataHi_Dcache : 0x00000000 - 0000001C
    TEXT_START : 0x21003178
    DATA_START : 0x260888A0
    Cause 0000040C (Code 0x3): TLB (store) exception
    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z

    === Flushing messages (22:02:12 UTC Thu Oct 28 2010) ===
    Buffered messages:
    *Oct 28 20:52:40.075: %LINK-3-UPDOWN: Interface SM1/0, changed state to up
    *Oct 28 20:52:42.195: %LINK-3-UPDOWN: Interface GigabitEthernet0/0, changed state to up
    *Oct 28 20:52:42.195: %LINK-3-UPDOWN: Interface GigabitEthernet0/1, changed state to down
    *Oct 28 20:52:42.195: %LINK-3-UPDOWN: Interface GigabitEthernet0/2, changed state to down
    *Oct 28 20:52:44.631: %LINK-3-UPDOWN: Interface SM1/1, changed state to up
    *Oct 28 20:53:01.655: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/0, changed state to up
    *Oct 28 20:53:01.923: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/1, changed state to up
    *Oct 28 20:53:02.075: %LINK-3-UPDOWN: Interface Foreign Exchange Station 0/1/0, changed state to up
    *Oct 28 20:53:02.075: %LINK-3-UPDOWN: Interface Foreign Exchange Station 0/1/1, changed state to up
    *Oct 28 20:53:43.739: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/0, changed state to operational status down due to cable removal
    *Oct 28 20:53:44.739: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/1, changed state to operational status down due to cable removal
    Queued messages:
    No warm reboot Storage
    *** System received a Bus Error exception ***
    signal= 0xa, code= 0x40c, context= 0x29726b74
    PC = 0x22768478, SP = 0x3022fbb8, RA = 0x22768424
    Cause Reg = 0x0000040c, Status Reg = 0x500099e3
    System Bootstrap, Version 15.0(1r)M6, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 2010 by cisco Systems, Inc.
    Total memory size = 512 MB - On-board = 512 MB, DIMM0 = 0 MB
    CISCO2911/K9 platform with 524288 Kbytes of main memory
    Main memory is configured to 72/-1(On-board/DIMM0) bit mode with ECC enabled

    Readonly ROMMON initialized
    program load complete, entry point: 0x80803000, size: 0x1b340

    IOS Image Load Test
    ___________________
    Digitally Signed Development Software
    program load complete, entry point: 0x81000000, size: 0x40b6b74
    Self decompressing the image : #############################################################################################################

    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2691036>
    or simply reply to this email.
    -- --
    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2691978>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2699015>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2699042>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2699089>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2699640>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2704890>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2703353>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2708817>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2712882>
    or simply reply to this email.

    Subject: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-
    Replied by: Ken Romo on 20-11-2010 01:34:38 AM
    Radhika,
     
    I never tried using the router with the PVDM, do you want to try and see if the router works with it?
     
    Ken
     
     
    Ken,

    Yes the IOS team was able to reproduce it. They are working on fixing the issue. Also one quick question the IOS team wanted to know was if the have used the PVDM successfully before the using sre-v.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Thursday, November 04, 2010 9:45 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    Do you know if the IOS team has been able to reproduce this yet?

    Thanks in advance,

    Ken Romo


    Ken,

    The IOS team is trying to reproduce this in their setup. I will let you know what the finding are or if we need a debug session with you (if they can¿t reproduce in their setup)



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Wednesday, November 03, 2010 9:03 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    Anything new here today?

    Thanks again,

    Ken



    Ken,

    Right now it looks an IOS bug but we need to reproduce this in house so we can confirm for sure. I will keep you in the loop on what we find. If it turns out to be an issue with this particular PVDM I will let you know.



    Appreciate all your help with this.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Tuesday, November 02, 2010 9:51 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    So what is the root cause?

    The IOS or the PVDMS?

    Do I need to RMA my PVDMS?

    Let me know thank you.

    Ken


    Ken,

    Thanks for the information. We will check internally if this has been tested. I will cancel the debug session for today since we most likely have the root cause for the issue. We will try to reproduce this internally and if we need further information from you will setup a different session.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Tuesday, November 02, 2010 8:49 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    The PVDMS is:

    PVDM3-16 V01
    S/N FOC14200FNK

    Is this what you were looking for?

    Ken


    Ken,

    I am not sure if it is the PVDM that is bad but it could be a bug in the IOS image also where you have pvdm and the SRE module it could be some issue. For now can you continute to do beta for SRE-v without the PVDMS.



    I will check with the team and get back to you as to how to proceed.



    Can you let me know what PVDM models you have so we can try to reproduce this in our lab.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Monday, November 01, 2010 3:59 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    I pulled the PVDM and it is working.

    Does this mean the PVDM is bad?

    Ken


    Ken,

    Please try out the new image sent by Brett to you when you get a chance. Also one difference we noticed is that you have PVDM¿s in your setup that we don not have in our test setup. Would it be possible to remove the PVDMS temporarily and try the ping? This may help us root cause the issue.



    I will also schedule a WebEx for tomorrow morning 10:30 PST with the IOS developer so we can take a look if the change of IOS image and removal of PVDM¿s does not solve the issue. Please let me know if that time slot does not work for you.



    Thanks,

    Radhika





    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Monday, November 01, 2010 11:19 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    Here you go:

    boxer#show vlan-switch
    VLAN Name Status Ports
    ---- -------------------------------- --------- -------------------------------
    1 default active
    1002 fddi-default act/unsup
    1003 token-ring-default act/unsup
    1004 fddinet-default act/unsup
    1005 trnet-default act/unsup
    VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2
    ---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------
    1 enet 100001 1500 - - - - - 1002 1003
    1002 fddi 101002 1500 - - - - - 1 1003
    1003 tr 101003 1500 1005 0 - - srb 1 1002
    1004 fdnet 101004 1500 - - 1 ibm - 0 0
    1005 trnet 101005 1500 - - 1 ibm - 0 0


    boxer#sh platform mgf module
    Registered Module Information
    Code: NR - Not Registered, TM - Trust Mode, SP - Scheduling Profile
    BL - Buffer Level, TR - Traffic Rate, PT - Pause Threshold
    slot vlan type/ID TM SP BL TR PT
    ---- ---- ---------- ------- --- ------ ----- ----
    ISM NR
    EHWIC-0 NR
    EHWIC-1 NR
    EHWIC-2 NR
    EHWIC-3 NR
    PVDM-0 2 PVDM/5 UP 1 low 1000 low
    PVDM-1 2 PVDM/5 UP 1 low 1000 low
    SM-1 1 Switch/3 UP 1 low 1000 high




    Thanks Ken. Can you also give us the output of the following.



    1) show vlan-switch

    2) ¿show platform mgf module¿ before the crash happens.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Monday, November 01, 2010 10:50 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    I will try whatever you suggest, just let me know when you have posted the new IOS.

    Below is my config:

    boxer#sh run
    Building configuration...

    Current configuration : 5777 bytes
    !
    version 15.1
    service timestamps debug datetime msec
    service timestamps log datetime msec
    no service password-encryption
    !
    hostname boxer
    !
    boot-start-marker
    boot system flash0 c2900-universalk9-mz.SSA.151-2.19.T
    boot-end-marker
    !
    !
    logging buffered 51200 warnings
    !
    no aaa new-model
    !
    no ipv6 cef
    ip source-route
    ip cef
    !
    !
    !
    !
    !
    ip domain name yourdomain.com
    multilink bundle-name authenticated
    !
    !
    !
    !
    !
    crypto pki token default removal timeout 0
    !
    crypto pki trustpoint TP-self-signed-1999750280
    enrollment selfsigned
    subject-name cn=IOS-Self-Signed-Certificate-1999750280
    revocation-check none
    rsakeypair TP-self-signed-1999750280
    !
    !
    crypto pki certificate chain TP-self-signed-1999750280
    certificate self-signed 01
    3082024C 308201B5 A0030201 02020101 300D0609 2A864886 F70D0101 04050030
    31312F30 2D060355 04031326 494F532D 53656C66 2D536967 6E65642D 43657274
    69666963 6174652D 31393939 37353032 3830301E 170D3130 31303230 32323335
    32365A17 0D323030 31303130 30303030 305A3031 312F302D 06035504 03132649
    4F532D53 656C662D 5369676E 65642D43 65727469 66696361 74652D31 39393937
    35303238 3030819F 300D0609 2A864886 F70D0101 01050003 818D0030 81890281
    81009378 2E139D79 DCA59865 14AB3398 870362B7 40BB9C13 A5DC5315 6108DF92
    5E78CF06 A40D4DB5 B66D410E FAFE75AC 764997B1 5C551A47 CFA00109 520352EC
    33A69E24 B3C1175B 136FC62A 8BE4637E B834059B FC7CAA6E 957DA0BB 66D8DC49
    80F82890 981FFCFE 0DC7E6F9 53287989 3887C5F6 AF59D0BE B502E11E FD16F556
    DBB90203 010001A3 74307230 0F060355 1D130101 FF040530 030101FF 301F0603
    551D1104 18301682 14626F78 65722E79 6F757264 6F6D6169 6E2E636F 6D301F06
    03551D23 04183016 80143541 7934E424 4B9A60DB E6C908C3 C20BAA17 D058301D
    0603551D 0E041604 14354179 34E4244B 9A60DBE6 C908C3C2 0BAA17D0 58300D06
    092A8648 86F70D01 01040500 03818100 3D222AB5 177D452F 153DCA26 1D7ECB49
    58BCBF60 DA18DC04 94B82EA3 76884EBC D7131641 08687C04 6C6645DF 78B2D2F8
    409BCAD7 50AF5091 B99614FD C2424D89 407A9109 BCA20473 F4CE33D4 4B126483
    C240C0B9 7A628E53 E419FEC3 B8853671 03113F5E 47FA8120 9F9A7A9D 11498FE0
    82C96578 8FD9770A EBD27F73 DF2E1487
    quit
    voice-card 0
    !
    !
    !
    !
    !
    !
    !
    license udi pid CISCO2911/K9 sn FTX1422A077
    hw-module pvdm 0/0
    !
    hw-module sm 1
    !
    !
    !
    username jack privilege 15 secret 5 $1$c5QR$fYGTbhWRKsBZ1JpNyIQGG1
    username marco privilege 15 secret 5 $1$amqq$5pI0T7mUViDL5Y.NqX/yz.
    !
    redundancy
    !
    !
    !
    !
    !
    !
    interface GigabitEthernet0/0
    description To tusqa network
    ip address 172.17.17.130 255.255.248.0
    duplex auto
    speed auto
    !
    interface GigabitEthernet0/1
    no ip address
    shutdown
    duplex auto
    speed auto
    !
    interface GigabitEthernet0/2
    no ip address
    shutdown
    duplex auto
    speed auto
    !
    interface SM1/0
    ip unnumbered GigabitEthernet0/0
    service-module ip address 172.17.17.129 255.255.248.0
    !Application: SRE-V Running on SMV
    service-module ip default-gateway 172.17.17.130
    service-module mgf ip address 10.62.64.1 255.255.255.0
    service-module mgf ip default-gateway 10.62.64.2
    !
    interface SM1/1
    description Internal switch interface connected to Service Module
    switchport mode trunk
    !
    interface Vlan1
    ip address 10.62.64.2 255.255.255.0
    !
    ip forward-protocol nd
    !
    ip http server
    ip http access-class 23
    ip http authentication local
    ip http secure-server
    ip http timeout-policy idle 60 life 86400 requests 10000
    !
    ip route 172.17.17.129 255.255.255.255 SM1/0
    !
    !
    !
    !
    control-plane
    !
    !
    voice-port 0/0/0
    !
    voice-port 0/0/1
    !
    voice-port 0/1/0
    !
    voice-port 0/1/1
    !
    !
    !
    mgcp profile default
    !
    !
    !
    !
    !
    gatekeeper
    shutdown
    !
    !
    banner exec ^C
    % Password expiration warning.
    -----------------------------------------------------------------------
    Cisco Configuration Professional (Cisco CP) is installed on this device
    and it provides the default username "cisco" for one-time use. If you have
    already used the username "cisco" to login to the router and your IOS image
    supports the "one-time" user option, then this username has already expired.
    You will not be able to login to the router with this username after you exit
    this session.
    It is strongly suggested that you create a new username with a privilege level
    of 15 using the following command.
    username <myuser> privilege 15 secret 0 <mypassword>
    Replace <myuser> and <mypassword> with the username and password you want to
    use.
    -----------------------------------------------------------------------
    ^C
    banner login ^C
    -----------------------------------------------------------------------
    Cisco Configuration Professional (Cisco CP) is installed on this device.
    This feature requires the one-time use of the username "cisco" with the
    password "cisco". These default credentials have a privilege level of 15.
    YOU MUST USE CISCO CP or the CISCO IOS CLI TO CHANGE THESE PUBLICLY-KNOWN
    CREDENTIALS
    Here are the Cisco IOS commands.
    username <myuser> privilege 15 secret 0 <mypassword>
    no username cisco
    Replace <myuser> and <mypassword> with the username and password you want
    to use.
    IF YOU DO NOT CHANGE THE PUBLICLY-KNOWN CREDENTIALS, YOU WILL NOT BE ABLE
    TO LOG INTO THE DEVICE AGAIN AFTER YOU HAVE LOGGED OFF.
    For more information about Cisco CP please follow the instructions in the
    QUICK START GUIDE for your router or go to http://www.cisco.com/go/ciscocp
    -----------------------------------------------------------------------
    ^C
    !
    line con 0
    login local
    line aux 0
    line 67
    no activation-character
    no exec
    transport preferred none
    transport input all
    transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
    stopbits 1
    flowcontrol software
    line vty 0 4
    privilege level 15
    login local
    transport input telnet
    line vty 5 15
    privilege level 15
    login local
    transport input telnet ssh
    !
    exception data-corruption buffer truncate
    scheduler allocate 20000 1000
    end



    Ken, Thanks for trying out the image for us. We are trying to reproduce this on our end but have had no luck so far. Can you please send us the output of show running-config from your router.



    Also we have one more image that we would like you to try it out before the debusg session would that be ok?



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Monday, November 01, 2010 10:22 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------

    Radhika,

    I tried the new OS and still getting same IOS crash.
    As mentioned I will work around your schedule so let me if you were able to get someone from the IOS team to help troubleshoot today.

    Thanks in advance,

    Ken Romo


    Ken,

    I am trying to get some help from the IOS team since this a router crash. So I will setup the webex session to debug for some time Monday so we can collect all the information and try out any suggestion from them.



    For Now We will post a newer IOS image to the beta Site and can you give that a try to see if that will solve the issue.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Friday, October 29, 2010 8:24 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    I will work around your schedule, anytime you are available, I will make myself available.
    email:
    kromo@opentext.com

    Thanks in advance,

    Ken Romo

    +++++++++++++++++++++++++++++++++

    Ken,

    Would a webex session tomorrow morning (any time between 10:00 and 1:00) work for you? Let me know the time that would work for you and also your email address so I can send you a webex invite.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Thursday, October 28, 2010 3:12 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Radhika Miriyala in Service Ready Engine Virtualizatio



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    No worries, we are trying to work this out together and I appreciate the help.
    s/m 1/1 is set as trunk but I went ahead and reconfigured to truank again and reloaded OS and get the same crash when I ping to the MGF interface from the SRE (I attached the errors at the bottom of this message).

    Ken,

    Sorry I just realized the mistake. I meant to say make the interface sm 1/1 as trunk.

    Sorry about the confusion.



    Please try it out.



    Thanks,

    Radhika



    boxer#
    %ALIGN-1-FATAL: Illegal access to a low address 22:02:10 UTC Thu Oct 28 2010
    addr=0x14, pc=0x22765BD8z , ra=0x22765B84z , sp=0x3022FBB8
    %ALIGN-1-FATAL: Illegal access to a low address 22:02:11 UTC Thu Oct 28 2010
    addr=0x14, pc=0x22765BD8z , ra=0x22765B84z , sp=0x3022FBB8

    22:02:11 UTC Thu Oct 28 2010: TLB (store) exception, CPU signal 10, PC = 0x22768478

    --------------------------------------------------------------------
    Possible software fault. Upon reccurence, please collect
    crashinfo, "show tech" and contact Cisco Technical Support.
    --------------------------------------------------------------------

    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z
    $0 : 00000000 00000000, AT : 00000000 29130000, v0 : 00000000 00000001, v1 : 00000000 0D8B8540
    a0 : 00000000 00000000, a1 : 00000000 0D8B8584, a2 : 00000000 2A2F8ABC, a3 : 00000000 00000004
    t0 : 00000000 00000020, t1 : 00000000 500099E1, t2 : 00000000 500081E0, t3 : FFFFFFFF FFFFFFF2
    t4 : 00000000 0000000E, t5 : 00000000 00000000, t6 : 00000000 0D95F890, t7 : 00000000 000001FF
    s0 : 00000000 00000000, s1 : 00000000 2A2FDB40, s2 : FFFFFFFF FFFFFFEC, s3 : 00000000 3080C980
    s4 : 00000000 0D95F89E, s5 : 00000000 2A300EE0, s6 : 00000000 00000000, s7 : 00000000 0000000E
    t8 : 00000000 000007FC, t9 : 00000000 2A300200, k0 : 00000000 00000000, k1 : 00000000 00000000
    gp : 00000000 29133C00, sp : 00000000 3022FBB8, s8 : 00000000 00000054, ra : 00000000 22768424
    EPC : 22768478, ErrorEPC : 80412AB4, SREG : 500099E3
    MDLO : 87126668, MDHI : D990ADBB, BadVaddr : 00000014
    CacheErr_Icache : 0x007F7F00 - 000040D8, CacheErr_Dcache : 0x00000000 - 00001FA0
    TagLo_Icache : 0x00000000 - 23642303, DataLo_Icache : 0xAFBF0018 - 0D81ADDB
    DataHi_Icache: 0x00000000 - 00000001
    TagLo_Dcache : 0x00000000 - 2277E583, TagHi_Dcache : 0x00000000 - 0912BD81
    DataLo_Dcache: 0x00000001 - 2368110C, DataHi_Dcache : 0x00000000 - 0000001C
    TEXT_START : 0x21003178
    DATA_START : 0x260888A0
    Cause 0000040C (Code 0x3): TLB (store) exception

    22:02:11 UTC Thu Oct 28 2010: TLB (store) exception, CPU signal 10, PC = 0x22768478

    --------------------------------------------------------------------
    Possible software fault. Upon reccurence, please collect
    crashinfo, "show tech" and contact Cisco Technical Support.
    --------------------------------------------------------------------

    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z
    $0 : 00000000 00000000, AT : 00000000 29130000, v0 : 00000000 00000001, v1 : 00000000 0D8B8540
    a0 : 00000000 00000000, a1 : 00000000 0D8B8584, a2 : 00000000 2A2F8ABC, a3 : 00000000 00000004
    t0 : 00000000 00000020, t1 : 00000000 500099E1, t2 : 00000000 500081E0, t3 : FFFFFFFF FFFFFFF2
    t4 : 00000000 0000000E, t5 : 00000000 00000000, t6 : 00000000 0D95F890, t7 : 00000000 000001FF
    s0 : 00000000 00000000, s1 : 00000000 2A2FDB40, s2 : FFFFFFFF FFFFFFEC, s3 : 00000000 3080C980
    s4 : 00000000 0D95F89E, s5 : 00000000 2A300EE0, s6 : 00000000 00000000, s7 : 00000000 0000000E
    t8 : 00000000 000007FC, t9 : 00000000 2A300200, k0 : 00000000 00000000, k1 : 00000000 00000000
    gp : 00000000 29133C00, sp : 00000000 3022FBB8, s8 : 00000000 00000054, ra : 00000000 22768424
    EPC : 22768478, ErrorEPC : 80412AB4, SREG : 500099E3
    MDLO : 87126668, MDHI : D990ADBB, BadVaddr : 00000014
    CacheErr_Icache : 0x007F7F00 - 000040D8, CacheErr_Dcache : 0x00000000 - 00001FA0
    TagLo_Icache : 0x00000000 - 23642303, DataLo_Icache : 0xAFBF0018 - 0D81ADDB
    DataHi_Icache: 0x00000000 - 00000001
    TagLo_Dcache : 0x00000000 - 2277E583, TagHi_Dcache : 0x00000000 - 0912BD81
    DataLo_Dcache: 0x00000001 - 2368110C, DataHi_Dcache : 0x00000000 - 0000001C
    TEXT_START : 0x21003178
    DATA_START : 0x260888A0
    Cause 0000040C (Code 0x3): TLB (store) exception
    Writing crashinfo to flash:crashinfo_20101028-220211-UTC
    22:02:11 UTC Thu Oct 28 2010: TLB (store) exception, CPU signal 10, PC = 0x22768478

    --------------------------------------------------------------------
    Possible software fault. Upon reccurence, please collect
    crashinfo, "show tech" and contact Cisco Technical Support.
    --------------------------------------------------------------------

    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z
    $0 : 00000000 00000000, AT : 00000000 29130000, v0 : 00000000 00000001, v1 : 00000000 0D8B8540
    a0 : 00000000 00000000, a1 : 00000000 0D8B8584, a2 : 00000000 2A2F8ABC, a3 : 00000000 00000004
    t0 : 00000000 00000020, t1 : 00000000 500099E1, t2 : 00000000 500081E0, t3 : FFFFFFFF FFFFFFF2
    t4 : 00000000 0000000E, t5 : 00000000 00000000, t6 : 00000000 0D95F890, t7 : 00000000 000001FF
    s0 : 00000000 00000000, s1 : 00000000 2A2FDB40, s2 : FFFFFFFF FFFFFFEC, s3 : 00000000 3080C980
    s4 : 00000000 0D95F89E, s5 : 00000000 2A300EE0, s6 : 00000000 00000000, s7 : 00000000 0000000E
    t8 : 00000000 000007FC, t9 : 00000000 2A300200, k0 : 00000000 00000000, k1 : 00000000 00000000
    gp : 00000000 29133C00, sp : 00000000 3022FBB8, s8 : 00000000 00000054, ra : 00000000 22768424
    EPC : 22768478, ErrorEPC : 80412AB4, SREG : 500099E3
    MDLO : 87126668, MDHI : D990ADBB, BadVaddr : 00000014
    CacheErr_Icache : 0x007F7F00 - 000040D8, CacheErr_Dcache : 0x00000000 - 00001FA0
    TagLo_Icache : 0x00000000 - 23642303, DataLo_Icache : 0xAFBF0018 - 0D81ADDB
    DataHi_Icache: 0x00000000 - 00000001
    TagLo_Dcache : 0x00000000 - 2277E583, TagHi_Dcache : 0x00000000 - 0912BD81
    DataLo_Dcache: 0x00000001 - 2368110C, DataHi_Dcache : 0x00000000 - 0000001C
    TEXT_START : 0x21003178
    DATA_START : 0x260888A0
    Cause 0000040C (Code 0x3): TLB (store) exception
    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z

    === Flushing messages (22:02:12 UTC Thu Oct 28 2010) ===
    Buffered messages:
    *Oct 28 20:52:40.075: %LINK-3-UPDOWN: Interface SM1/0, changed state to up
    *Oct 28 20:52:42.195: %LINK-3-UPDOWN: Interface GigabitEthernet0/0, changed state to up
    *Oct 28 20:52:42.195: %LINK-3-UPDOWN: Interface GigabitEthernet0/1, changed state to down
    *Oct 28 20:52:42.195: %LINK-3-UPDOWN: Interface GigabitEthernet0/2, changed state to down
    *Oct 28 20:52:44.631: %LINK-3-UPDOWN: Interface SM1/1, changed state to up
    *Oct 28 20:53:01.655: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/0, changed state to up
    *Oct 28 20:53:01.923: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/1, changed state to up
    *Oct 28 20:53:02.075: %LINK-3-UPDOWN: Interface Foreign Exchange Station 0/1/0, changed state to up
    *Oct 28 20:53:02.075: %LINK-3-UPDOWN: Interface Foreign Exchange Station 0/1/1, changed state to up
    *Oct 28 20:53:43.739: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/0, changed state to operational status down due to cable removal
    *Oct 28 20:53:44.739: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/1, changed state to operational status down due to cable removal
    Queued messages:
    No warm reboot Storage
    *** System received a Bus Error exception ***
    signal= 0xa, code= 0x40c, context= 0x29726b74
    PC = 0x22768478, SP = 0x3022fbb8, RA = 0x22768424
    Cause Reg = 0x0000040c, Status Reg = 0x500099e3
    System Bootstrap, Version 15.0(1r)M6, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 2010 by cisco Systems, Inc.
    Total memory size = 512 MB - On-board = 512 MB, DIMM0 = 0 MB
    CISCO2911/K9 platform with 524288 Kbytes of main memory
    Main memory is configured to 72/-1(On-board/DIMM0) bit mode with ECC enabled

    Readonly ROMMON initialized
    program load complete, entry point: 0x80803000, size: 0x1b340

    IOS Image Load Test
    ___________________
    Digitally Signed Development Software
    program load complete, entry point: 0x81000000, size: 0x40b6b74
    Self decompressing the image : #############################################################################################################

    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2691036>
    or simply reply to this email.
    -- --
    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2691978>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2699015>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2699042>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2699089>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2699640>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2704890>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2703353>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2708817>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2712882>
    or simply reply to this email.


    Subject: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-
    Replied by: Ken Romo on 20-11-2010 01:34:38 AM
    Radhika,
     
    The router seemed to work with the PVDM before configuring the sre-v, is there a particular test they would like me to try?
     
    Ken
     
     

    Ken,

    Yes the IOS team was able to reproduce it. They are working on fixing the issue. Also one quick question the IOS team wanted to know was if the have used the PVDM successfully before the using sre-v.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Thursday, November 04, 2010 9:45 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    Do you know if the IOS team has been able to reproduce this yet?

    Thanks in advance,

    Ken Romo


    Ken,

    The IOS team is trying to reproduce this in their setup. I will let you know what the finding are or if we need a debug session with you (if they can¿t reproduce in their setup)



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Wednesday, November 03, 2010 9:03 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    Anything new here today?

    Thanks again,

    Ken



    Ken,

    Right now it looks an IOS bug but we need to reproduce this in house so we can confirm for sure. I will keep you in the loop on what we find. If it turns out to be an issue with this particular PVDM I will let you know.



    Appreciate all your help with this.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Tuesday, November 02, 2010 9:51 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    So what is the root cause?

    The IOS or the PVDMS?

    Do I need to RMA my PVDMS?

    Let me know thank you.

    Ken


    Ken,

    Thanks for the information. We will check internally if this has been tested. I will cancel the debug session for today since we most likely have the root cause for the issue. We will try to reproduce this internally and if we need further information from you will setup a different session.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Tuesday, November 02, 2010 8:49 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    The PVDMS is:

    PVDM3-16 V01
    S/N FOC14200FNK

    Is this what you were looking for?

    Ken


    Ken,

    I am not sure if it is the PVDM that is bad but it could be a bug in the IOS image also where you have pvdm and the SRE module it could be some issue. For now can you continute to do beta for SRE-v without the PVDMS.



    I will check with the team and get back to you as to how to proceed.



    Can you let me know what PVDM models you have so we can try to reproduce this in our lab.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Monday, November 01, 2010 3:59 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    I pulled the PVDM and it is working.

    Does this mean the PVDM is bad?

    Ken


    Ken,

    Please try out the new image sent by Brett to you when you get a chance. Also one difference we noticed is that you have PVDM¿s in your setup that we don not have in our test setup. Would it be possible to remove the PVDMS temporarily and try the ping? This may help us root cause the issue.



    I will also schedule a WebEx for tomorrow morning 10:30 PST with the IOS developer so we can take a look if the change of IOS image and removal of PVDM¿s does not solve the issue. Please let me know if that time slot does not work for you.



    Thanks,

    Radhika





    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Monday, November 01, 2010 11:19 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    Here you go:

    boxer#show vlan-switch
    VLAN Name Status Ports
    ---- -------------------------------- --------- -------------------------------
    1 default active
    1002 fddi-default act/unsup
    1003 token-ring-default act/unsup
    1004 fddinet-default act/unsup
    1005 trnet-default act/unsup
    VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2
    ---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------
    1 enet 100001 1500 - - - - - 1002 1003
    1002 fddi 101002 1500 - - - - - 1 1003
    1003 tr 101003 1500 1005 0 - - srb 1 1002
    1004 fdnet 101004 1500 - - 1 ibm - 0 0
    1005 trnet 101005 1500 - - 1 ibm - 0 0


    boxer#sh platform mgf module
    Registered Module Information
    Code: NR - Not Registered, TM - Trust Mode, SP - Scheduling Profile
    BL - Buffer Level, TR - Traffic Rate, PT - Pause Threshold
    slot vlan type/ID TM SP BL TR PT
    ---- ---- ---------- ------- --- ------ ----- ----
    ISM NR
    EHWIC-0 NR
    EHWIC-1 NR
    EHWIC-2 NR
    EHWIC-3 NR
    PVDM-0 2 PVDM/5 UP 1 low 1000 low
    PVDM-1 2 PVDM/5 UP 1 low 1000 low
    SM-1 1 Switch/3 UP 1 low 1000 high




    Thanks Ken. Can you also give us the output of the following.



    1) show vlan-switch

    2) ¿show platform mgf module¿ before the crash happens.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Monday, November 01, 2010 10:50 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    I will try whatever you suggest, just let me know when you have posted the new IOS.

    Below is my config:

    boxer#sh run
    Building configuration...

    Current configuration : 5777 bytes
    !
    version 15.1
    service timestamps debug datetime msec
    service timestamps log datetime msec
    no service password-encryption
    !
    hostname boxer
    !
    boot-start-marker
    boot system flash0 c2900-universalk9-mz.SSA.151-2.19.T
    boot-end-marker
    !
    !
    logging buffered 51200 warnings
    !
    no aaa new-model
    !
    no ipv6 cef
    ip source-route
    ip cef
    !
    !
    !
    !
    !
    ip domain name yourdomain.com
    multilink bundle-name authenticated
    !
    !
    !
    !
    !
    crypto pki token default removal timeout 0
    !
    crypto pki trustpoint TP-self-signed-1999750280
    enrollment selfsigned
    subject-name cn=IOS-Self-Signed-Certificate-1999750280
    revocation-check none
    rsakeypair TP-self-signed-1999750280
    !
    !
    crypto pki certificate chain TP-self-signed-1999750280
    certificate self-signed 01
    3082024C 308201B5 A0030201 02020101 300D0609 2A864886 F70D0101 04050030
    31312F30 2D060355 04031326 494F532D 53656C66 2D536967 6E65642D 43657274
    69666963 6174652D 31393939 37353032 3830301E 170D3130 31303230 32323335
    32365A17 0D323030 31303130 30303030 305A3031 312F302D 06035504 03132649
    4F532D53 656C662D 5369676E 65642D43 65727469 66696361 74652D31 39393937
    35303238 3030819F 300D0609 2A864886 F70D0101 01050003 818D0030 81890281
    81009378 2E139D79 DCA59865 14AB3398 870362B7 40BB9C13 A5DC5315 6108DF92
    5E78CF06 A40D4DB5 B66D410E FAFE75AC 764997B1 5C551A47 CFA00109 520352EC
    33A69E24 B3C1175B 136FC62A 8BE4637E B834059B FC7CAA6E 957DA0BB 66D8DC49
    80F82890 981FFCFE 0DC7E6F9 53287989 3887C5F6 AF59D0BE B502E11E FD16F556
    DBB90203 010001A3 74307230 0F060355 1D130101 FF040530 030101FF 301F0603
    551D1104 18301682 14626F78 65722E79 6F757264 6F6D6169 6E2E636F 6D301F06
    03551D23 04183016 80143541 7934E424 4B9A60DB E6C908C3 C20BAA17 D058301D
    0603551D 0E041604 14354179 34E4244B 9A60DBE6 C908C3C2 0BAA17D0 58300D06
    092A8648 86F70D01 01040500 03818100 3D222AB5 177D452F 153DCA26 1D7ECB49
    58BCBF60 DA18DC04 94B82EA3 76884EBC D7131641 08687C04 6C6645DF 78B2D2F8
    409BCAD7 50AF5091 B99614FD C2424D89 407A9109 BCA20473 F4CE33D4 4B126483
    C240C0B9 7A628E53 E419FEC3 B8853671 03113F5E 47FA8120 9F9A7A9D 11498FE0
    82C96578 8FD9770A EBD27F73 DF2E1487
    quit
    voice-card 0
    !
    !
    !
    !
    !
    !
    !
    license udi pid CISCO2911/K9 sn FTX1422A077
    hw-module pvdm 0/0
    !
    hw-module sm 1
    !
    !
    !
    username jack privilege 15 secret 5 $1$c5QR$fYGTbhWRKsBZ1JpNyIQGG1
    username marco privilege 15 secret 5 $1$amqq$5pI0T7mUViDL5Y.NqX/yz.
    !
    redundancy
    !
    !
    !
    !
    !
    !
    interface GigabitEthernet0/0
    description To tusqa network
    ip address 172.17.17.130 255.255.248.0
    duplex auto
    speed auto
    !
    interface GigabitEthernet0/1
    no ip address
    shutdown
    duplex auto
    speed auto
    !
    interface GigabitEthernet0/2
    no ip address
    shutdown
    duplex auto
    speed auto
    !
    interface SM1/0
    ip unnumbered GigabitEthernet0/0
    service-module ip address 172.17.17.129 255.255.248.0
    !Application: SRE-V Running on SMV
    service-module ip default-gateway 172.17.17.130
    service-module mgf ip address 10.62.64.1 255.255.255.0
    service-module mgf ip default-gateway 10.62.64.2
    !
    interface SM1/1
    description Internal switch interface connected to Service Module
    switchport mode trunk
    !
    interface Vlan1
    ip address 10.62.64.2 255.255.255.0
    !
    ip forward-protocol nd
    !
    ip http server
    ip http access-class 23
    ip http authentication local
    ip http secure-server
    ip http timeout-policy idle 60 life 86400 requests 10000
    !
    ip route 172.17.17.129 255.255.255.255 SM1/0
    !
    !
    !
    !
    control-plane
    !
    !
    voice-port 0/0/0
    !
    voice-port 0/0/1
    !
    voice-port 0/1/0
    !
    voice-port 0/1/1
    !
    !
    !
    mgcp profile default
    !
    !
    !
    !
    !
    gatekeeper
    shutdown
    !
    !
    banner exec ^C
    % Password expiration warning.
    -----------------------------------------------------------------------
    Cisco Configuration Professional (Cisco CP) is installed on this device
    and it provides the default username "cisco" for one-time use. If you have
    already used the username "cisco" to login to the router and your IOS image
    supports the "one-time" user option, then this username has already expired.
    You will not be able to login to the router with this username after you exit
    this session.
    It is strongly suggested that you create a new username with a privilege level
    of 15 using the following command.
    username <myuser> privilege 15 secret 0 <mypassword>
    Replace <myuser> and <mypassword> with the username and password you want to
    use.
    -----------------------------------------------------------------------
    ^C
    banner login ^C
    -----------------------------------------------------------------------
    Cisco Configuration Professional (Cisco CP) is installed on this device.
    This feature requires the one-time use of the username "cisco" with the
    password "cisco". These default credentials have a privilege level of 15.
    YOU MUST USE CISCO CP or the CISCO IOS CLI TO CHANGE THESE PUBLICLY-KNOWN
    CREDENTIALS
    Here are the Cisco IOS commands.
    username <myuser> privilege 15 secret 0 <mypassword>
    no username cisco
    Replace <myuser> and <mypassword> with the username and password you want
    to use.
    IF YOU DO NOT CHANGE THE PUBLICLY-KNOWN CREDENTIALS, YOU WILL NOT BE ABLE
    TO LOG INTO THE DEVICE AGAIN AFTER YOU HAVE LOGGED OFF.
    For more information about Cisco CP please follow the instructions in the
    QUICK START GUIDE for your router or go to http://www.cisco.com/go/ciscocp
    -----------------------------------------------------------------------
    ^C
    !
    line con 0
    login local
    line aux 0
    line 67
    no activation-character
    no exec
    transport preferred none
    transport input all
    transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
    stopbits 1
    flowcontrol software
    line vty 0 4
    privilege level 15
    login local
    transport input telnet
    line vty 5 15
    privilege level 15
    login local
    transport input telnet ssh
    !
    exception data-corruption buffer truncate
    scheduler allocate 20000 1000
    end



    Ken, Thanks for trying out the image for us. We are trying to reproduce this on our end but have had no luck so far. Can you please send us the output of show running-config from your router.



    Also we have one more image that we would like you to try it out before the debusg session would that be ok?



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Monday, November 01, 2010 10:22 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------

    Radhika,

    I tried the new OS and still getting same IOS crash.
    As mentioned I will work around your schedule so let me if you were able to get someone from the IOS team to help troubleshoot today.

    Thanks in advance,

    Ken Romo


    Ken,

    I am trying to get some help from the IOS team since this a router crash. So I will setup the webex session to debug for some time Monday so we can collect all the information and try out any suggestion from them.



    For Now We will post a newer IOS image to the beta Site and can you give that a try to see if that will solve the issue.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Friday, October 29, 2010 8:24 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    I will work around your schedule, anytime you are available, I will make myself available.
    email:
    kromo@opentext.com

    Thanks in advance,

    Ken Romo

    +++++++++++++++++++++++++++++++++

    Ken,

    Would a webex session tomorrow morning (any time between 10:00 and 1:00) work for you? Let me know the time that would work for you and also your email address so I can send you a webex invite.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Thursday, October 28, 2010 3:12 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Radhika Miriyala in Service Ready Engine Virtualizatio



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    No worries, we are trying to work this out together and I appreciate the help.
    s/m 1/1 is set as trunk but I went ahead and reconfigured to truank again and reloaded OS and get the same crash when I ping to the MGF interface from the SRE (I attached the errors at the bottom of this message).

    Ken,

    Sorry I just realized the mistake. I meant to say make the interface sm 1/1 as trunk.

    Sorry about the confusion.



    Please try it out.



    Thanks,

    Radhika



    boxer#
    %ALIGN-1-FATAL: Illegal access to a low address 22:02:10 UTC Thu Oct 28 2010
    addr=0x14, pc=0x22765BD8z , ra=0x22765B84z , sp=0x3022FBB8
    %ALIGN-1-FATAL: Illegal access to a low address 22:02:11 UTC Thu Oct 28 2010
    addr=0x14, pc=0x22765BD8z , ra=0x22765B84z , sp=0x3022FBB8

    22:02:11 UTC Thu Oct 28 2010: TLB (store) exception, CPU signal 10, PC = 0x22768478

    --------------------------------------------------------------------
    Possible software fault. Upon reccurence, please collect
    crashinfo, "show tech" and contact Cisco Technical Support.
    --------------------------------------------------------------------

    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z
    $0 : 00000000 00000000, AT : 00000000 29130000, v0 : 00000000 00000001, v1 : 00000000 0D8B8540
    a0 : 00000000 00000000, a1 : 00000000 0D8B8584, a2 : 00000000 2A2F8ABC, a3 : 00000000 00000004
    t0 : 00000000 00000020, t1 : 00000000 500099E1, t2 : 00000000 500081E0, t3 : FFFFFFFF FFFFFFF2
    t4 : 00000000 0000000E, t5 : 00000000 00000000, t6 : 00000000 0D95F890, t7 : 00000000 000001FF
    s0 : 00000000 00000000, s1 : 00000000 2A2FDB40, s2 : FFFFFFFF FFFFFFEC, s3 : 00000000 3080C980
    s4 : 00000000 0D95F89E, s5 : 00000000 2A300EE0, s6 : 00000000 00000000, s7 : 00000000 0000000E
    t8 : 00000000 000007FC, t9 : 00000000 2A300200, k0 : 00000000 00000000, k1 : 00000000 00000000
    gp : 00000000 29133C00, sp : 00000000 3022FBB8, s8 : 00000000 00000054, ra : 00000000 22768424
    EPC : 22768478, ErrorEPC : 80412AB4, SREG : 500099E3
    MDLO : 87126668, MDHI : D990ADBB, BadVaddr : 00000014
    CacheErr_Icache : 0x007F7F00 - 000040D8, CacheErr_Dcache : 0x00000000 - 00001FA0
    TagLo_Icache : 0x00000000 - 23642303, DataLo_Icache : 0xAFBF0018 - 0D81ADDB
    DataHi_Icache: 0x00000000 - 00000001
    TagLo_Dcache : 0x00000000 - 2277E583, TagHi_Dcache : 0x00000000 - 0912BD81
    DataLo_Dcache: 0x00000001 - 2368110C, DataHi_Dcache : 0x00000000 - 0000001C
    TEXT_START : 0x21003178
    DATA_START : 0x260888A0
    Cause 0000040C (Code 0x3): TLB (store) exception

    22:02:11 UTC Thu Oct 28 2010: TLB (store) exception, CPU signal 10, PC = 0x22768478

    --------------------------------------------------------------------
    Possible software fault. Upon reccurence, please collect
    crashinfo, "show tech" and contact Cisco Technical Support.
    --------------------------------------------------------------------

    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z
    $0 : 00000000 00000000, AT : 00000000 29130000, v0 : 00000000 00000001, v1 : 00000000 0D8B8540
    a0 : 00000000 00000000, a1 : 00000000 0D8B8584, a2 : 00000000 2A2F8ABC, a3 : 00000000 00000004
    t0 : 00000000 00000020, t1 : 00000000 500099E1, t2 : 00000000 500081E0, t3 : FFFFFFFF FFFFFFF2
    t4 : 00000000 0000000E, t5 : 00000000 00000000, t6 : 00000000 0D95F890, t7 : 00000000 000001FF
    s0 : 00000000 00000000, s1 : 00000000 2A2FDB40, s2 : FFFFFFFF FFFFFFEC, s3 : 00000000 3080C980
    s4 : 00000000 0D95F89E, s5 : 00000000 2A300EE0, s6 : 00000000 00000000, s7 : 00000000 0000000E
    t8 : 00000000 000007FC, t9 : 00000000 2A300200, k0 : 00000000 00000000, k1 : 00000000 00000000
    gp : 00000000 29133C00, sp : 00000000 3022FBB8, s8 : 00000000 00000054, ra : 00000000 22768424
    EPC : 22768478, ErrorEPC : 80412AB4, SREG : 500099E3
    MDLO : 87126668, MDHI : D990ADBB, BadVaddr : 00000014
    CacheErr_Icache : 0x007F7F00 - 000040D8, CacheErr_Dcache : 0x00000000 - 00001FA0
    TagLo_Icache : 0x00000000 - 23642303, DataLo_Icache : 0xAFBF0018 - 0D81ADDB
    DataHi_Icache: 0x00000000 - 00000001
    TagLo_Dcache : 0x00000000 - 2277E583, TagHi_Dcache : 0x00000000 - 0912BD81
    DataLo_Dcache: 0x00000001 - 2368110C, DataHi_Dcache : 0x00000000 - 0000001C
    TEXT_START : 0x21003178
    DATA_START : 0x260888A0
    Cause 0000040C (Code 0x3): TLB (store) exception
    Writing crashinfo to flash:crashinfo_20101028-220211-UTC
    22:02:11 UTC Thu Oct 28 2010: TLB (store) exception, CPU signal 10, PC = 0x22768478

    --------------------------------------------------------------------
    Possible software fault. Upon reccurence, please collect
    crashinfo, "show tech" and contact Cisco Technical Support.
    --------------------------------------------------------------------

    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z
    $0 : 00000000 00000000, AT : 00000000 29130000, v0 : 00000000 00000001, v1 : 00000000 0D8B8540
    a0 : 00000000 00000000, a1 : 00000000 0D8B8584, a2 : 00000000 2A2F8ABC, a3 : 00000000 00000004
    t0 : 00000000 00000020, t1 : 00000000 500099E1, t2 : 00000000 500081E0, t3 : FFFFFFFF FFFFFFF2
    t4 : 00000000 0000000E, t5 : 00000000 00000000, t6 : 00000000 0D95F890, t7 : 00000000 000001FF
    s0 : 00000000 00000000, s1 : 00000000 2A2FDB40, s2 : FFFFFFFF FFFFFFEC, s3 : 00000000 3080C980
    s4 : 00000000 0D95F89E, s5 : 00000000 2A300EE0, s6 : 00000000 00000000, s7 : 00000000 0000000E
    t8 : 00000000 000007FC, t9 : 00000000 2A300200, k0 : 00000000 00000000, k1 : 00000000 00000000
    gp : 00000000 29133C00, sp : 00000000 3022FBB8, s8 : 00000000 00000054, ra : 00000000 22768424
    EPC : 22768478, ErrorEPC : 80412AB4, SREG : 500099E3
    MDLO : 87126668, MDHI : D990ADBB, BadVaddr : 00000014
    CacheErr_Icache : 0x007F7F00 - 000040D8, CacheErr_Dcache : 0x00000000 - 00001FA0
    TagLo_Icache : 0x00000000 - 23642303, DataLo_Icache : 0xAFBF0018 - 0D81ADDB
    DataHi_Icache: 0x00000000 - 00000001
    TagLo_Dcache : 0x00000000 - 2277E583, TagHi_Dcache : 0x00000000 - 0912BD81
    DataLo_Dcache: 0x00000001 - 2368110C, DataHi_Dcache : 0x00000000 - 0000001C
    TEXT_START : 0x21003178
    DATA_START : 0x260888A0
    Cause 0000040C (Code 0x3): TLB (store) exception
    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z

    === Flushing messages (22:02:12 UTC Thu Oct 28 2010) ===
    Buffered messages:
    *Oct 28 20:52:40.075: %LINK-3-UPDOWN: Interface SM1/0, changed state to up
    *Oct 28 20:52:42.195: %LINK-3-UPDOWN: Interface GigabitEthernet0/0, changed state to up
    *Oct 28 20:52:42.195: %LINK-3-UPDOWN: Interface GigabitEthernet0/1, changed state to down
    *Oct 28 20:52:42.195: %LINK-3-UPDOWN: Interface GigabitEthernet0/2, changed state to down
    *Oct 28 20:52:44.631: %LINK-3-UPDOWN: Interface SM1/1, changed state to up
    *Oct 28 20:53:01.655: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/0, changed state to up
    *Oct 28 20:53:01.923: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/1, changed state to up
    *Oct 28 20:53:02.075: %LINK-3-UPDOWN: Interface Foreign Exchange Station 0/1/0, changed state to up
    *Oct 28 20:53:02.075: %LINK-3-UPDOWN: Interface Foreign Exchange Station 0/1/1, changed state to up
    *Oct 28 20:53:43.739: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/0, changed state to operational status down due to cable removal
    *Oct 28 20:53:44.739: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/1, changed state to operational status down due to cable removal
    Queued messages:
    No warm reboot Storage
    *** System received a Bus Error exception ***
    signal= 0xa, code= 0x40c, context= 0x29726b74
    PC = 0x22768478, SP = 0x3022fbb8, RA = 0x22768424
    Cause Reg = 0x0000040c, Status Reg = 0x500099e3
    System Bootstrap, Version 15.0(1r)M6, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 2010 by cisco Systems, Inc.
    Total memory size = 512 MB - On-board = 512 MB, DIMM0 = 0 MB
    CISCO2911/K9 platform with 524288 Kbytes of main memory
    Main memory is configured to 72/-1(On-board/DIMM0) bit mode with ECC enabled

    Readonly ROMMON initialized
    program load complete, entry point: 0x80803000, size: 0x1b340

    IOS Image Load Test
    ___________________
    Digitally Signed Development Software
    program load complete, entry point: 0x81000000, size: 0x40b6b74
    Self decompressing the image : #############################################################################################################

    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2691036>
    or simply reply to this email.
    -- --
    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2691978>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2699015>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2699042>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2699089>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2699640>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2704890>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2703353>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2708817>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2712882>
    or simply reply to this email.



    Subject: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-
    Replied by: Radhika Miriyala on 20-11-2010 01:34:38 AM
    Ken,

    I think what you did is fine but I will check with IOs team to confirm if they want any additional tests.



    Appreciate your trying all the tests for us.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Thursday, November 04, 2010 11:00 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    The router seemed to work with the PVDM before configuring the sre-v, is there a particular test they would like me to try?

    Ken



    Ken,

    Yes the IOS team was able to reproduce it. They are working on fixing the issue. Also one quick question the IOS team wanted to know was if the have used the PVDM successfully before the using sre-v.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Thursday, November 04, 2010 9:45 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    Do you know if the IOS team has been able to reproduce this yet?

    Thanks in advance,

    Ken Romo


    Ken,

    The IOS team is trying to reproduce this in their setup. I will let you know what the finding are or if we need a debug session with you (if they can¿t reproduce in their setup)



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Wednesday, November 03, 2010 9:03 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    Anything new here today?

    Thanks again,

    Ken



    Ken,

    Right now it looks an IOS bug but we need to reproduce this in house so we can confirm for sure. I will keep you in the loop on what we find. If it turns out to be an issue with this particular PVDM I will let you know.



    Appreciate all your help with this.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Tuesday, November 02, 2010 9:51 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    So what is the root cause?

    The IOS or the PVDMS?

    Do I need to RMA my PVDMS?

    Let me know thank you.

    Ken


    Ken,

    Thanks for the information. We will check internally if this has been tested. I will cancel the debug session for today since we most likely have the root cause for the issue. We will try to reproduce this internally and if we need further information from you will setup a different session.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Tuesday, November 02, 2010 8:49 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    The PVDMS is:

    PVDM3-16 V01
    S/N FOC14200FNK

    Is this what you were looking for?

    Ken


    Ken,

    I am not sure if it is the PVDM that is bad but it could be a bug in the IOS image also where you have pvdm and the SRE module it could be some issue. For now can you continute to do beta for SRE-v without the PVDMS.



    I will check with the team and get back to you as to how to proceed.



    Can you let me know what PVDM models you have so we can try to reproduce this in our lab.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Monday, November 01, 2010 3:59 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    I pulled the PVDM and it is working.

    Does this mean the PVDM is bad?

    Ken


    Ken,

    Please try out the new image sent by Brett to you when you get a chance. Also one difference we noticed is that you have PVDM¿s in your setup that we don not have in our test setup. Would it be possible to remove the PVDMS temporarily and try the ping? This may help us root cause the issue.



    I will also schedule a WebEx for tomorrow morning 10:30 PST with the IOS developer so we can take a look if the change of IOS image and removal of PVDM¿s does not solve the issue. Please let me know if that time slot does not work for you.



    Thanks,

    Radhika





    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Monday, November 01, 2010 11:19 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    Here you go:

    boxer#show vlan-switch
    VLAN Name Status Ports
    ---- -------------------------------- --------- -------------------------------
    1 default active
    1002 fddi-default act/unsup
    1003 token-ring-default act/unsup
    1004 fddinet-default act/unsup
    1005 trnet-default act/unsup
    VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2
    ---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------
    1 enet 100001 1500 - - - - - 1002 1003
    1002 fddi 101002 1500 - - - - - 1 1003
    1003 tr 101003 1500 1005 0 - - srb 1 1002
    1004 fdnet 101004 1500 - - 1 ibm - 0 0
    1005 trnet 101005 1500 - - 1 ibm - 0 0


    boxer#sh platform mgf module
    Registered Module Information
    Code: NR - Not Registered, TM - Trust Mode, SP - Scheduling Profile
    BL - Buffer Level, TR - Traffic Rate, PT - Pause Threshold
    slot vlan type/ID TM SP BL TR PT
    ---- ---- ---------- ------- --- ------ ----- ----
    ISM NR
    EHWIC-0 NR
    EHWIC-1 NR
    EHWIC-2 NR
    EHWIC-3 NR
    PVDM-0 2 PVDM/5 UP 1 low 1000 low
    PVDM-1 2 PVDM/5 UP 1 low 1000 low
    SM-1 1 Switch/3 UP 1 low 1000 high




    Thanks Ken. Can you also give us the output of the following.



    1) show vlan-switch

    2) ¿show platform mgf module¿ before the crash happens.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Monday, November 01, 2010 10:50 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    I will try whatever you suggest, just let me know when you have posted the new IOS.

    Below is my config:

    boxer#sh run
    Building configuration...

    Current configuration : 5777 bytes
    !
    version 15.1
    service timestamps debug datetime msec
    service timestamps log datetime msec
    no service password-encryption
    !
    hostname boxer
    !
    boot-start-marker
    boot system flash0 c2900-universalk9-mz.SSA.151-2.19.T
    boot-end-marker
    !
    !
    logging buffered 51200 warnings
    !
    no aaa new-model
    !
    no ipv6 cef
    ip source-route
    ip cef
    !
    !
    !
    !
    !
    ip domain name yourdomain.com
    multilink bundle-name authenticated
    !
    !
    !
    !
    !
    crypto pki token default removal timeout 0
    !
    crypto pki trustpoint TP-self-signed-1999750280
    enrollment selfsigned
    subject-name cn=IOS-Self-Signed-Certificate-1999750280
    revocation-check none
    rsakeypair TP-self-signed-1999750280
    !
    !
    crypto pki certificate chain TP-self-signed-1999750280
    certificate self-signed 01
    3082024C 308201B5 A0030201 02020101 300D0609 2A864886 F70D0101 04050030
    31312F30 2D060355 04031326 494F532D 53656C66 2D536967 6E65642D 43657274
    69666963 6174652D 31393939 37353032 3830301E 170D3130 31303230 32323335
    32365A17 0D323030 31303130 30303030 305A3031 312F302D 06035504 03132649
    4F532D53 656C662D 5369676E 65642D43 65727469 66696361 74652D31 39393937
    35303238 3030819F 300D0609 2A864886 F70D0101 01050003 818D0030 81890281
    81009378 2E139D79 DCA59865 14AB3398 870362B7 40BB9C13 A5DC5315 6108DF92
    5E78CF06 A40D4DB5 B66D410E FAFE75AC 764997B1 5C551A47 CFA00109 520352EC
    33A69E24 B3C1175B 136FC62A 8BE4637E B834059B FC7CAA6E 957DA0BB 66D8DC49
    80F82890 981FFCFE 0DC7E6F9 53287989 3887C5F6 AF59D0BE B502E11E FD16F556
    DBB90203 010001A3 74307230 0F060355 1D130101 FF040530 030101FF 301F0603
    551D1104 18301682 14626F78 65722E79 6F757264 6F6D6169 6E2E636F 6D301F06
    03551D23 04183016 80143541 7934E424 4B9A60DB E6C908C3 C20BAA17 D058301D
    0603551D 0E041604 14354179 34E4244B 9A60DBE6 C908C3C2 0BAA17D0 58300D06
    092A8648 86F70D01 01040500 03818100 3D222AB5 177D452F 153DCA26 1D7ECB49
    58BCBF60 DA18DC04 94B82EA3 76884EBC D7131641 08687C04 6C6645DF 78B2D2F8
    409BCAD7 50AF5091 B99614FD C2424D89 407A9109 BCA20473 F4CE33D4 4B126483
    C240C0B9 7A628E53 E419FEC3 B8853671 03113F5E 47FA8120 9F9A7A9D 11498FE0
    82C96578 8FD9770A EBD27F73 DF2E1487
    quit
    voice-card 0
    !
    !
    !
    !
    !
    !
    !
    license udi pid CISCO2911/K9 sn FTX1422A077
    hw-module pvdm 0/0
    !
    hw-module sm 1
    !
    !
    !
    username jack privilege 15 secret 5 $1$c5QR$fYGTbhWRKsBZ1JpNyIQGG1
    username marco privilege 15 secret 5 $1$amqq$5pI0T7mUViDL5Y.NqX/yz.
    !
    redundancy
    !
    !
    !
    !
    !
    !
    interface GigabitEthernet0/0
    description To tusqa network
    ip address 172.17.17.130 255.255.248.0
    duplex auto
    speed auto
    !
    interface GigabitEthernet0/1
    no ip address
    shutdown
    duplex auto
    speed auto
    !
    interface GigabitEthernet0/2
    no ip address
    shutdown
    duplex auto
    speed auto
    !
    interface SM1/0
    ip unnumbered GigabitEthernet0/0
    service-module ip address 172.17.17.129 255.255.248.0
    !Application: SRE-V Running on SMV
    service-module ip default-gateway 172.17.17.130
    service-module mgf ip address 10.62.64.1 255.255.255.0
    service-module mgf ip default-gateway 10.62.64.2
    !
    interface SM1/1
    description Internal switch interface connected to Service Module
    switchport mode trunk
    !
    interface Vlan1
    ip address 10.62.64.2 255.255.255.0
    !
    ip forward-protocol nd
    !
    ip http server
    ip http access-class 23
    ip http authentication local
    ip http secure-server
    ip http timeout-policy idle 60 life 86400 requests 10000
    !
    ip route 172.17.17.129 255.255.255.255 SM1/0
    !
    !
    !
    !
    control-plane
    !
    !
    voice-port 0/0/0
    !
    voice-port 0/0/1
    !
    voice-port 0/1/0
    !
    voice-port 0/1/1
    !
    !
    !
    mgcp profile default
    !
    !
    !
    !
    !
    gatekeeper
    shutdown
    !
    !
    banner exec ^C
    % Password expiration warning.
    -----------------------------------------------------------------------
    Cisco Configuration Professional (Cisco CP) is installed on this device
    and it provides the default username "cisco" for one-time use. If you have
    already used the username "cisco" to login to the router and your IOS image
    supports the "one-time" user option, then this username has already expired.
    You will not be able to login to the router with this username after you exit
    this session.
    It is strongly suggested that you create a new username with a privilege level
    of 15 using the following command.
    username <myuser> privilege 15 secret 0 <mypassword>
    Replace <myuser> and <mypassword> with the username and password you want to
    use.
    -----------------------------------------------------------------------
    ^C
    banner login ^C
    -----------------------------------------------------------------------
    Cisco Configuration Professional (Cisco CP) is installed on this device.
    This feature requires the one-time use of the username "cisco" with the
    password "cisco". These default credentials have a privilege level of 15.
    YOU MUST USE CISCO CP or the CISCO IOS CLI TO CHANGE THESE PUBLICLY-KNOWN
    CREDENTIALS
    Here are the Cisco IOS commands.
    username <myuser> privilege 15 secret 0 <mypassword>
    no username cisco
    Replace <myuser> and <mypassword> with the username and password you want
    to use.
    IF YOU DO NOT CHANGE THE PUBLICLY-KNOWN CREDENTIALS, YOU WILL NOT BE ABLE
    TO LOG INTO THE DEVICE AGAIN AFTER YOU HAVE LOGGED OFF.
    For more information about Cisco CP please follow the instructions in the
    QUICK START GUIDE for your router or go to http://www.cisco.com/go/ciscocp
    -----------------------------------------------------------------------
    ^C
    !
    line con 0
    login local
    line aux 0
    line 67
    no activation-character
    no exec
    transport preferred none
    transport input all
    transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
    stopbits 1
    flowcontrol software
    line vty 0 4
    privilege level 15
    login local
    transport input telnet
    line vty 5 15
    privilege level 15
    login local
    transport input telnet ssh
    !
    exception data-corruption buffer truncate
    scheduler allocate 20000 1000
    end



    Ken, Thanks for trying out the image for us. We are trying to reproduce this on our end but have had no luck so far. Can you please send us the output of show running-config from your router.



    Also we have one more image that we would like you to try it out before the debusg session would that be ok?



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Monday, November 01, 2010 10:22 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------

    Radhika,

    I tried the new OS and still getting same IOS crash.
    As mentioned I will work around your schedule so let me if you were able to get someone from the IOS team to help troubleshoot today.

    Thanks in advance,

    Ken Romo


    Ken,

    I am trying to get some help from the IOS team since this a router crash. So I will setup the webex session to debug for some time Monday so we can collect all the information and try out any suggestion from them.



    For Now We will post a newer IOS image to the beta Site and can you give that a try to see if that will solve the issue.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Friday, October 29, 2010 8:24 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    I will work around your schedule, anytime you are available, I will make myself available.
    email:
    kromo@opentext.com

    Thanks in advance,

    Ken Romo

    +++++++++++++++++++++++++++++++++

    Ken,

    Would a webex session tomorrow morning (any time between 10:00 and 1:00) work for you? Let me know the time that would work for you and also your email address so I can send you a webex invite.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Thursday, October 28, 2010 3:12 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Radhika Miriyala in Service Ready Engine Virtualizatio



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    No worries, we are trying to work this out together and I appreciate the help.
    s/m 1/1 is set as trunk but I went ahead and reconfigured to truank again and reloaded OS and get the same crash when I ping to the MGF interface from the SRE (I attached the errors at the bottom of this message).

    Ken,

    Sorry I just realized the mistake. I meant to say make the interface sm 1/1 as trunk.

    Sorry about the confusion.



    Please try it out.



    Thanks,

    Radhika



    boxer#
    %ALIGN-1-FATAL: Illegal access to a low address 22:02:10 UTC Thu Oct 28 2010
    addr=0x14, pc=0x22765BD8z , ra=0x22765B84z , sp=0x3022FBB8
    %ALIGN-1-FATAL: Illegal access to a low address 22:02:11 UTC Thu Oct 28 2010
    addr=0x14, pc=0x22765BD8z , ra=0x22765B84z , sp=0x3022FBB8

    22:02:11 UTC Thu Oct 28 2010: TLB (store) exception, CPU signal 10, PC = 0x22768478

    --------------------------------------------------------------------
    Possible software fault. Upon reccurence, please collect
    crashinfo, "show tech" and contact Cisco Technical Support.
    --------------------------------------------------------------------

    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z
    $0 : 00000000 00000000, AT : 00000000 29130000, v0 : 00000000 00000001, v1 : 00000000 0D8B8540
    a0 : 00000000 00000000, a1 : 00000000 0D8B8584, a2 : 00000000 2A2F8ABC, a3 : 00000000 00000004
    t0 : 00000000 00000020, t1 : 00000000 500099E1, t2 : 00000000 500081E0, t3 : FFFFFFFF FFFFFFF2
    t4 : 00000000 0000000E, t5 : 00000000 00000000, t6 : 00000000 0D95F890, t7 : 00000000 000001FF
    s0 : 00000000 00000000, s1 : 00000000 2A2FDB40, s2 : FFFFFFFF FFFFFFEC, s3 : 00000000 3080C980
    s4 : 00000000 0D95F89E, s5 : 00000000 2A300EE0, s6 : 00000000 00000000, s7 : 00000000 0000000E
    t8 : 00000000 000007FC, t9 : 00000000 2A300200, k0 : 00000000 00000000, k1 : 00000000 00000000
    gp : 00000000 29133C00, sp : 00000000 3022FBB8, s8 : 00000000 00000054, ra : 00000000 22768424
    EPC : 22768478, ErrorEPC : 80412AB4, SREG : 500099E3
    MDLO : 87126668, MDHI : D990ADBB, BadVaddr : 00000014
    CacheErr_Icache : 0x007F7F00 - 000040D8, CacheErr_Dcache : 0x00000000 - 00001FA0
    TagLo_Icache : 0x00000000 - 23642303, DataLo_Icache : 0xAFBF0018 - 0D81ADDB
    DataHi_Icache: 0x00000000 - 00000001
    TagLo_Dcache : 0x00000000 - 2277E583, TagHi_Dcache : 0x00000000 - 0912BD81
    DataLo_Dcache: 0x00000001 - 2368110C, DataHi_Dcache : 0x00000000 - 0000001C
    TEXT_START : 0x21003178
    DATA_START : 0x260888A0
    Cause 0000040C (Code 0x3): TLB (store) exception

    22:02:11 UTC Thu Oct 28 2010: TLB (store) exception, CPU signal 10, PC = 0x22768478

    --------------------------------------------------------------------
    Possible software fault. Upon reccurence, please collect
    crashinfo, "show tech" and contact Cisco Technical Support.
    --------------------------------------------------------------------

    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z
    $0 : 00000000 00000000, AT : 00000000 29130000, v0 : 00000000 00000001, v1 : 00000000 0D8B8540
    a0 : 00000000 00000000, a1 : 00000000 0D8B8584, a2 : 00000000 2A2F8ABC, a3 : 00000000 00000004
    t0 : 00000000 00000020, t1 : 00000000 500099E1, t2 : 00000000 500081E0, t3 : FFFFFFFF FFFFFFF2
    t4 : 00000000 0000000E, t5 : 00000000 00000000, t6 : 00000000 0D95F890, t7 : 00000000 000001FF
    s0 : 00000000 00000000, s1 : 00000000 2A2FDB40, s2 : FFFFFFFF FFFFFFEC, s3 : 00000000 3080C980
    s4 : 00000000 0D95F89E, s5 : 00000000 2A300EE0, s6 : 00000000 00000000, s7 : 00000000 0000000E
    t8 : 00000000 000007FC, t9 : 00000000 2A300200, k0 : 00000000 00000000, k1 : 00000000 00000000
    gp : 00000000 29133C00, sp : 00000000 3022FBB8, s8 : 00000000 00000054, ra : 00000000 22768424
    EPC : 22768478, ErrorEPC : 80412AB4, SREG : 500099E3
    MDLO : 87126668, MDHI : D990ADBB, BadVaddr : 00000014
    CacheErr_Icache : 0x007F7F00 - 000040D8, CacheErr_Dcache : 0x00000000 - 00001FA0
    TagLo_Icache : 0x00000000 - 23642303, DataLo_Icache : 0xAFBF0018 - 0D81ADDB
    DataHi_Icache: 0x00000000 - 00000001
    TagLo_Dcache : 0x00000000 - 2277E583, TagHi_Dcache : 0x00000000 - 0912BD81
    DataLo_Dcache: 0x00000001 - 2368110C, DataHi_Dcache : 0x00000000 - 0000001C
    TEXT_START : 0x21003178
    DATA_START : 0x260888A0
    Cause 0000040C (Code 0x3): TLB (store) exception
    Writing crashinfo to flash:crashinfo_20101028-220211-UTC
    22:02:11 UTC Thu Oct 28 2010: TLB (store) exception, CPU signal 10, PC = 0x22768478

    --------------------------------------------------------------------
    Possible software fault. Upon reccurence, please collect
    crashinfo, "show tech" and contact Cisco Technical Support.
    --------------------------------------------------------------------

    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z
    $0 : 00000000 00000000, AT : 00000000 29130000, v0 : 00000000 00000001, v1 : 00000000 0D8B8540
    a0 : 00000000 00000000, a1 : 00000000 0D8B8584, a2 : 00000000 2A2F8ABC, a3 : 00000000 00000004
    t0 : 00000000 00000020, t1 : 00000000 500099E1, t2 : 00000000 500081E0, t3 : FFFFFFFF FFFFFFF2
    t4 : 00000000 0000000E, t5 : 00000000 00000000, t6 : 00000000 0D95F890, t7 : 00000000 000001FF
    s0 : 00000000 00000000, s1 : 00000000 2A2FDB40, s2 : FFFFFFFF FFFFFFEC, s3 : 00000000 3080C980
    s4 : 00000000 0D95F89E, s5 : 00000000 2A300EE0, s6 : 00000000 00000000, s7 : 00000000 0000000E
    t8 : 00000000 000007FC, t9 : 00000000 2A300200, k0 : 00000000 00000000, k1 : 00000000 00000000
    gp : 00000000 29133C00, sp : 00000000 3022FBB8, s8 : 00000000 00000054, ra : 00000000 22768424
    EPC : 22768478, ErrorEPC : 80412AB4, SREG : 500099E3
    MDLO : 87126668, MDHI : D990ADBB, BadVaddr : 00000014
    CacheErr_Icache : 0x007F7F00 - 000040D8, CacheErr_Dcache : 0x00000000 - 00001FA0
    TagLo_Icache : 0x00000000 - 23642303, DataLo_Icache : 0xAFBF0018 - 0D81ADDB
    DataHi_Icache: 0x00000000 - 00000001
    TagLo_Dcache : 0x00000000 - 2277E583, TagHi_Dcache : 0x00000000 - 0912BD81
    DataLo_Dcache: 0x00000001 - 2368110C, DataHi_Dcache : 0x00000000 - 0000001C
    TEXT_START : 0x21003178
    DATA_START : 0x260888A0
    Cause 0000040C (Code 0x3): TLB (store) exception
    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z

    === Flushing messages (22:02:12 UTC Thu Oct 28 2010) ===
    Buffered messages:
    *Oct 28 20:52:40.075: %LINK-3-UPDOWN: Interface SM1/0, changed state to up
    *Oct 28 20:52:42.195: %LINK-3-UPDOWN: Interface GigabitEthernet0/0, changed state to up
    *Oct 28 20:52:42.195: %LINK-3-UPDOWN: Interface GigabitEthernet0/1, changed state to down
    *Oct 28 20:52:42.195: %LINK-3-UPDOWN: Interface GigabitEthernet0/2, changed state to down
    *Oct 28 20:52:44.631: %LINK-3-UPDOWN: Interface SM1/1, changed state to up
    *Oct 28 20:53:01.655: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/0, changed state to up
    *Oct 28 20:53:01.923: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/1, changed state to up
    *Oct 28 20:53:02.075: %LINK-3-UPDOWN: Interface Foreign Exchange Station 0/1/0, changed state to up
    *Oct 28 20:53:02.075: %LINK-3-UPDOWN: Interface Foreign Exchange Station 0/1/1, changed state to up
    *Oct 28 20:53:43.739: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/0, changed state to operational status down due to cable removal
    *Oct 28 20:53:44.739: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/1, changed state to operational status down due to cable removal
    Queued messages:
    No warm reboot Storage
    *** System received a Bus Error exception ***
    signal= 0xa, code= 0x40c, context= 0x29726b74
    PC = 0x22768478, SP = 0x3022fbb8, RA = 0x22768424
    Cause Reg = 0x0000040c, Status Reg = 0x500099e3
    System Bootstrap, Version 15.0(1r)M6, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 2010 by cisco Systems, Inc.
    Total memory size = 512 MB - On-board = 512 MB, DIMM0 = 0 MB
    CISCO2911/K9 platform with 524288 Kbytes of main memory
    Main memory is configured to 72/-1(On-board/DIMM0) bit mode with ECC enabled

    Readonly ROMMON initialized
    program load complete, entry point: 0x80803000, size: 0x1b340

    IOS Image Load Test
    ___________________
    Digitally Signed Development Software
    program load complete, entry point: 0x81000000, size: 0x40b6b74
    Self decompressing the image : #############################################################################################################

    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2691036>
    or simply reply to this email.
    -- --
    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2691978>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2699015>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2699042>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2699089>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2699640>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2704890>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2703353>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2708817>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2712882>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2713045>
    or simply reply to this email.

    Subject: Re: New Message from Radhika Miriyala in Service Ready Engine Virtualizatio
    Replied by: Anurag Gurtu on 20-11-2010 01:34:38 AM
    What are we using PVDMs for? Voice, video?

    Thanks

    Anurag Gurtu

    Subject: RE: New Message from Radhika Miriyala in Service Ready Engine Virtualizatio
    Replied by: Radhika Miriyala on 20-11-2010 01:34:38 AM
    Ken,

    Can you try the following to make sure the PVDM is working as expected.


    A) sh voice dsp group slot 0
    dsp 1:
    State: UP, firmware: 28.0.126  <<<<  (out put would be something like this)
    ...

    debug vpm dsp

    Thanks,

    Radhika





    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Thursday, November 04, 2010 11:12 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Radhika Miriyala in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Radhika Miriyala has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Ken,

    I think what you did is fine but I will check with IOs team to confirm if they want any additional tests.



    Appreciate your trying all the tests for us.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Thursday, November 04, 2010 11:00 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    The router seemed to work with the PVDM before configuring the sre-v, is there a particular test they would like me to try?

    Ken



    Ken,

    Yes the IOS team was able to reproduce it. They are working on fixing the issue. Also one quick question the IOS team wanted to know was if the have used the PVDM successfully before the using sre-v.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Thursday, November 04, 2010 9:45 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    Do you know if the IOS team has been able to reproduce this yet?

    Thanks in advance,

    Ken Romo


    Ken,

    The IOS team is trying to reproduce this in their setup. I will let you know what the finding are or if we need a debug session with you (if they can¿t reproduce in their setup)



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Wednesday, November 03, 2010 9:03 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    Anything new here today?

    Thanks again,

    Ken



    Ken,

    Right now it looks an IOS bug but we need to reproduce this in house so we can confirm for sure. I will keep you in the loop on what we find. If it turns out to be an issue with this particular PVDM I will let you know.



    Appreciate all your help with this.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Tuesday, November 02, 2010 9:51 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    So what is the root cause?

    The IOS or the PVDMS?

    Do I need to RMA my PVDMS?

    Let me know thank you.

    Ken


    Ken,

    Thanks for the information. We will check internally if this has been tested. I will cancel the debug session for today since we most likely have the root cause for the issue. We will try to reproduce this internally and if we need further information from you will setup a different session.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Tuesday, November 02, 2010 8:49 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    The PVDMS is:

    PVDM3-16 V01
    S/N FOC14200FNK

    Is this what you were looking for?

    Ken


    Ken,

    I am not sure if it is the PVDM that is bad but it could be a bug in the IOS image also where you have pvdm and the SRE module it could be some issue. For now can you continute to do beta for SRE-v without the PVDMS.



    I will check with the team and get back to you as to how to proceed.



    Can you let me know what PVDM models you have so we can try to reproduce this in our lab.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Monday, November 01, 2010 3:59 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    I pulled the PVDM and it is working.

    Does this mean the PVDM is bad?

    Ken


    Ken,

    Please try out the new image sent by Brett to you when you get a chance. Also one difference we noticed is that you have PVDM¿s in your setup that we don not have in our test setup. Would it be possible to remove the PVDMS temporarily and try the ping? This may help us root cause the issue.



    I will also schedule a WebEx for tomorrow morning 10:30 PST with the IOS developer so we can take a look if the change of IOS image and removal of PVDM¿s does not solve the issue. Please let me know if that time slot does not work for you.



    Thanks,

    Radhika





    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Monday, November 01, 2010 11:19 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    Here you go:

    boxer#show vlan-switch
    VLAN Name Status Ports
    ---- -------------------------------- --------- -------------------------------
    1 default active
    1002 fddi-default act/unsup
    1003 token-ring-default act/unsup
    1004 fddinet-default act/unsup
    1005 trnet-default act/unsup
    VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2
    ---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------
    1 enet 100001 1500 - - - - - 1002 1003
    1002 fddi 101002 1500 - - - - - 1 1003
    1003 tr 101003 1500 1005 0 - - srb 1 1002
    1004 fdnet 101004 1500 - - 1 ibm - 0 0
    1005 trnet 101005 1500 - - 1 ibm - 0 0


    boxer#sh platform mgf module
    Registered Module Information
    Code: NR - Not Registered, TM - Trust Mode, SP - Scheduling Profile
    BL - Buffer Level, TR - Traffic Rate, PT - Pause Threshold
    slot vlan type/ID TM SP BL TR PT
    ---- ---- ---------- ------- --- ------ ----- ----
    ISM NR
    EHWIC-0 NR
    EHWIC-1 NR
    EHWIC-2 NR
    EHWIC-3 NR
    PVDM-0 2 PVDM/5 UP 1 low 1000 low
    PVDM-1 2 PVDM/5 UP 1 low 1000 low
    SM-1 1 Switch/3 UP 1 low 1000 high




    Thanks Ken. Can you also give us the output of the following.



    1) show vlan-switch

    2) ¿show platform mgf module¿ before the crash happens.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Monday, November 01, 2010 10:50 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    I will try whatever you suggest, just let me know when you have posted the new IOS.

    Below is my config:

    boxer#sh run
    Building configuration...

    Current configuration : 5777 bytes
    !
    version 15.1
    service timestamps debug datetime msec
    service timestamps log datetime msec
    no service password-encryption
    !
    hostname boxer
    !
    boot-start-marker
    boot system flash0 c2900-universalk9-mz.SSA.151-2.19.T
    boot-end-marker
    !
    !
    logging buffered 51200 warnings
    !
    no aaa new-model
    !
    no ipv6 cef
    ip source-route
    ip cef
    !
    !
    !
    !
    !
    ip domain name yourdomain.com
    multilink bundle-name authenticated
    !
    !
    !
    !
    !
    crypto pki token default removal timeout 0
    !
    crypto pki trustpoint TP-self-signed-1999750280
    enrollment selfsigned
    subject-name cn=IOS-Self-Signed-Certificate-1999750280
    revocation-check none
    rsakeypair TP-self-signed-1999750280
    !
    !
    crypto pki certificate chain TP-self-signed-1999750280
    certificate self-signed 01
    3082024C 308201B5 A0030201 02020101 300D0609 2A864886 F70D0101 04050030
    31312F30 2D060355 04031326 494F532D 53656C66 2D536967 6E65642D 43657274
    69666963 6174652D 31393939 37353032 3830301E 170D3130 31303230 32323335
    32365A17 0D323030 31303130 30303030 305A3031 312F302D 06035504 03132649
    4F532D53 656C662D 5369676E 65642D43 65727469 66696361 74652D31 39393937
    35303238 3030819F 300D0609 2A864886 F70D0101 01050003 818D0030 81890281
    81009378 2E139D79 DCA59865 14AB3398 870362B7 40BB9C13 A5DC5315 6108DF92
    5E78CF06 A40D4DB5 B66D410E FAFE75AC 764997B1 5C551A47 CFA00109 520352EC
    33A69E24 B3C1175B 136FC62A 8BE4637E B834059B FC7CAA6E 957DA0BB 66D8DC49
    80F82890 981FFCFE 0DC7E6F9 53287989 3887C5F6 AF59D0BE B502E11E FD16F556
    DBB90203 010001A3 74307230 0F060355 1D130101 FF040530 030101FF 301F0603
    551D1104 18301682 14626F78 65722E79 6F757264 6F6D6169 6E2E636F 6D301F06
    03551D23 04183016 80143541 7934E424 4B9A60DB E6C908C3 C20BAA17 D058301D
    0603551D 0E041604 14354179 34E4244B 9A60DBE6 C908C3C2 0BAA17D0 58300D06
    092A8648 86F70D01 01040500 03818100 3D222AB5 177D452F 153DCA26 1D7ECB49
    58BCBF60 DA18DC04 94B82EA3 76884EBC D7131641 08687C04 6C6645DF 78B2D2F8
    409BCAD7 50AF5091 B99614FD C2424D89 407A9109 BCA20473 F4CE33D4 4B126483
    C240C0B9 7A628E53 E419FEC3 B8853671 03113F5E 47FA8120 9F9A7A9D 11498FE0
    82C96578 8FD9770A EBD27F73 DF2E1487
    quit
    voice-card 0
    !
    !
    !
    !
    !
    !
    !
    license udi pid CISCO2911/K9 sn FTX1422A077
    hw-module pvdm 0/0
    !
    hw-module sm 1
    !
    !
    !
    username jack privilege 15 secret 5 $1$c5QR$fYGTbhWRKsBZ1JpNyIQGG1
    username marco privilege 15 secret 5 $1$amqq$5pI0T7mUViDL5Y.NqX/yz.
    !
    redundancy
    !
    !
    !
    !
    !
    !
    interface GigabitEthernet0/0
    description To tusqa network
    ip address 172.17.17.130 255.255.248.0
    duplex auto
    speed auto
    !
    interface GigabitEthernet0/1
    no ip address
    shutdown
    duplex auto
    speed auto
    !
    interface GigabitEthernet0/2
    no ip address
    shutdown
    duplex auto
    speed auto
    !
    interface SM1/0
    ip unnumbered GigabitEthernet0/0
    service-module ip address 172.17.17.129 255.255.248.0
    !Application: SRE-V Running on SMV
    service-module ip default-gateway 172.17.17.130
    service-module mgf ip address 10.62.64.1 255.255.255.0
    service-module mgf ip default-gateway 10.62.64.2
    !
    interface SM1/1
    description Internal switch interface connected to Service Module
    switchport mode trunk
    !
    interface Vlan1
    ip address 10.62.64.2 255.255.255.0
    !
    ip forward-protocol nd
    !
    ip http server
    ip http access-class 23
    ip http authentication local
    ip http secure-server
    ip http timeout-policy idle 60 life 86400 requests 10000
    !
    ip route 172.17.17.129 255.255.255.255 SM1/0
    !
    !
    !
    !
    control-plane
    !
    !
    voice-port 0/0/0
    !
    voice-port 0/0/1
    !
    voice-port 0/1/0
    !
    voice-port 0/1/1
    !
    !
    !
    mgcp profile default
    !
    !
    !
    !
    !
    gatekeeper
    shutdown
    !
    !
    banner exec ^C
    % Password expiration warning.
    -----------------------------------------------------------------------
    Cisco Configuration Professional (Cisco CP) is installed on this device
    and it provides the default username "cisco" for one-time use. If you have
    already used the username "cisco" to login to the router and your IOS image
    supports the "one-time" user option, then this username has already expired.
    You will not be able to login to the router with this username after you exit
    this session.
    It is strongly suggested that you create a new username with a privilege level
    of 15 using the following command.
    username <myuser> privilege 15 secret 0 <mypassword>
    Replace <myuser> and <mypassword> with the username and password you want to
    use.
    -----------------------------------------------------------------------
    ^C
    banner login ^C
    -----------------------------------------------------------------------
    Cisco Configuration Professional (Cisco CP) is installed on this device.
    This feature requires the one-time use of the username "cisco" with the
    password "cisco". These default credentials have a privilege level of 15.
    YOU MUST USE CISCO CP or the CISCO IOS CLI TO CHANGE THESE PUBLICLY-KNOWN
    CREDENTIALS
    Here are the Cisco IOS commands.
    username <myuser> privilege 15 secret 0 <mypassword>
    no username cisco
    Replace <myuser> and <mypassword> with the username and password you want
    to use.
    IF YOU DO NOT CHANGE THE PUBLICLY-KNOWN CREDENTIALS, YOU WILL NOT BE ABLE
    TO LOG INTO THE DEVICE AGAIN AFTER YOU HAVE LOGGED OFF.
    For more information about Cisco CP please follow the instructions in the
    QUICK START GUIDE for your router or go to http://www.cisco.com/go/ciscocp
    -----------------------------------------------------------------------
    ^C
    !
    line con 0
    login local
    line aux 0
    line 67
    no activation-character
    no exec
    transport preferred none
    transport input all
    transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
    stopbits 1
    flowcontrol software
    line vty 0 4
    privilege level 15
    login local
    transport input telnet
    line vty 5 15
    privilege level 15
    login local
    transport input telnet ssh
    !
    exception data-corruption buffer truncate
    scheduler allocate 20000 1000
    end



    Ken, Thanks for trying out the image for us. We are trying to reproduce this on our end but have had no luck so far. Can you please send us the output of show running-config from your router.



    Also we have one more image that we would like you to try it out before the debusg session would that be ok?



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Monday, November 01, 2010 10:22 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------

    Radhika,

    I tried the new OS and still getting same IOS crash.
    As mentioned I will work around your schedule so let me if you were able to get someone from the IOS team to help troubleshoot today.

    Thanks in advance,

    Ken Romo


    Ken,

    I am trying to get some help from the IOS team since this a router crash. So I will setup the webex session to debug for some time Monday so we can collect all the information and try out any suggestion from them.



    For Now We will post a newer IOS image to the beta Site and can you give that a try to see if that will solve the issue.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Friday, October 29, 2010 8:24 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    I will work around your schedule, anytime you are available, I will make myself available.
    email:
    kromo@opentext.com

    Thanks in advance,

    Ken Romo

    +++++++++++++++++++++++++++++++++

    Ken,

    Would a webex session tomorrow morning (any time between 10:00 and 1:00) work for you? Let me know the time that would work for you and also your email address so I can send you a webex invite.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Thursday, October 28, 2010 3:12 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Radhika Miriyala in Service Ready Engine Virtualizatio



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    No worries, we are trying to work this out together and I appreciate the help.
    s/m 1/1 is set as trunk but I went ahead and reconfigured to truank again and reloaded OS and get the same crash when I ping to the MGF interface from the SRE (I attached the errors at the bottom of this message).

    Ken,

    Sorry I just realized the mistake. I meant to say make the interface sm 1/1 as trunk.

    Sorry about the confusion.



    Please try it out.



    Thanks,

    Radhika



    boxer#
    %ALIGN-1-FATAL: Illegal access to a low address 22:02:10 UTC Thu Oct 28 2010
    addr=0x14, pc=0x22765BD8z , ra=0x22765B84z , sp=0x3022FBB8
    %ALIGN-1-FATAL: Illegal access to a low address 22:02:11 UTC Thu Oct 28 2010
    addr=0x14, pc=0x22765BD8z , ra=0x22765B84z , sp=0x3022FBB8

    22:02:11 UTC Thu Oct 28 2010: TLB (store) exception, CPU signal 10, PC = 0x22768478

    --------------------------------------------------------------------
    Possible software fault. Upon reccurence, please collect
    crashinfo, "show tech" and contact Cisco Technical Support.
    --------------------------------------------------------------------

    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z
    $0 : 00000000 00000000, AT : 00000000 29130000, v0 : 00000000 00000001, v1 : 00000000 0D8B8540
    a0 : 00000000 00000000, a1 : 00000000 0D8B8584, a2 : 00000000 2A2F8ABC, a3 : 00000000 00000004
    t0 : 00000000 00000020, t1 : 00000000 500099E1, t2 : 00000000 500081E0, t3 : FFFFFFFF FFFFFFF2
    t4 : 00000000 0000000E, t5 : 00000000 00000000, t6 : 00000000 0D95F890, t7 : 00000000 000001FF
    s0 : 00000000 00000000, s1 : 00000000 2A2FDB40, s2 : FFFFFFFF FFFFFFEC, s3 : 00000000 3080C980
    s4 : 00000000 0D95F89E, s5 : 00000000 2A300EE0, s6 : 00000000 00000000, s7 : 00000000 0000000E
    t8 : 00000000 000007FC, t9 : 00000000 2A300200, k0 : 00000000 00000000, k1 : 00000000 00000000
    gp : 00000000 29133C00, sp : 00000000 3022FBB8, s8 : 00000000 00000054, ra : 00000000 22768424
    EPC : 22768478, ErrorEPC : 80412AB4, SREG : 500099E3
    MDLO : 87126668, MDHI : D990ADBB, BadVaddr : 00000014
    CacheErr_Icache : 0x007F7F00 - 000040D8, CacheErr_Dcache : 0x00000000 - 00001FA0
    TagLo_Icache : 0x00000000 - 23642303, DataLo_Icache : 0xAFBF0018 - 0D81ADDB
    DataHi_Icache: 0x00000000 - 00000001
    TagLo_Dcache : 0x00000000 - 2277E583, TagHi_Dcache : 0x00000000 - 0912BD81
    DataLo_Dcache: 0x00000001 - 2368110C, DataHi_Dcache : 0x00000000 - 0000001C
    TEXT_START : 0x21003178
    DATA_START : 0x260888A0
    Cause 0000040C (Code 0x3): TLB (store) exception

    22:02:11 UTC Thu Oct 28 2010: TLB (store) exception, CPU signal 10, PC = 0x22768478

    --------------------------------------------------------------------
    Possible software fault. Upon reccurence, please collect
    crashinfo, "show tech" and contact Cisco Technical Support.
    --------------------------------------------------------------------

    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z
    $0 : 00000000 00000000, AT : 00000000 29130000, v0 : 00000000 00000001, v1 : 00000000 0D8B8540
    a0 : 00000000 00000000, a1 : 00000000 0D8B8584, a2 : 00000000 2A2F8ABC, a3 : 00000000 00000004
    t0 : 00000000 00000020, t1 : 00000000 500099E1, t2 : 00000000 500081E0, t3 : FFFFFFFF FFFFFFF2
    t4 : 00000000 0000000E, t5 : 00000000 00000000, t6 : 00000000 0D95F890, t7 : 00000000 000001FF
    s0 : 00000000 00000000, s1 : 00000000 2A2FDB40, s2 : FFFFFFFF FFFFFFEC, s3 : 00000000 3080C980
    s4 : 00000000 0D95F89E, s5 : 00000000 2A300EE0, s6 : 00000000 00000000, s7 : 00000000 0000000E
    t8 : 00000000 000007FC, t9 : 00000000 2A300200, k0 : 00000000 00000000, k1 : 00000000 00000000
    gp : 00000000 29133C00, sp : 00000000 3022FBB8, s8 : 00000000 00000054, ra : 00000000 22768424
    EPC : 22768478, ErrorEPC : 80412AB4, SREG : 500099E3
    MDLO : 87126668, MDHI : D990ADBB, BadVaddr : 00000014
    CacheErr_Icache : 0x007F7F00 - 000040D8, CacheErr_Dcache : 0x00000000 - 00001FA0
    TagLo_Icache : 0x00000000 - 23642303, DataLo_Icache : 0xAFBF0018 - 0D81ADDB
    DataHi_Icache: 0x00000000 - 00000001
    TagLo_Dcache : 0x00000000 - 2277E583, TagHi_Dcache : 0x00000000 - 0912BD81
    DataLo_Dcache: 0x00000001 - 2368110C, DataHi_Dcache : 0x00000000 - 0000001C
    TEXT_START : 0x21003178
    DATA_START : 0x260888A0
    Cause 0000040C (Code 0x3): TLB (store) exception
    Writing crashinfo to flash:crashinfo_20101028-220211-UTC
    22:02:11 UTC Thu Oct 28 2010: TLB (store) exception, CPU signal 10, PC = 0x22768478

    --------------------------------------------------------------------
    Possible software fault. Upon reccurence, please collect
    crashinfo, "show tech" and contact Cisco Technical Support.
    --------------------------------------------------------------------

    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z
    $0 : 00000000 00000000, AT : 00000000 29130000, v0 : 00000000 00000001, v1 : 00000000 0D8B8540
    a0 : 00000000 00000000, a1 : 00000000 0D8B8584, a2 : 00000000 2A2F8ABC, a3 : 00000000 00000004
    t0 : 00000000 00000020, t1 : 00000000 500099E1, t2 : 00000000 500081E0, t3 : FFFFFFFF FFFFFFF2
    t4 : 00000000 0000000E, t5 : 00000000 00000000, t6 : 00000000 0D95F890, t7 : 00000000 000001FF
    s0 : 00000000 00000000, s1 : 00000000 2A2FDB40, s2 : FFFFFFFF FFFFFFEC, s3 : 00000000 3080C980
    s4 : 00000000 0D95F89E, s5 : 00000000 2A300EE0, s6 : 00000000 00000000, s7 : 00000000 0000000E
    t8 : 00000000 000007FC, t9 : 00000000 2A300200, k0 : 00000000 00000000, k1 : 00000000 00000000
    gp : 00000000 29133C00, sp : 00000000 3022FBB8, s8 : 00000000 00000054, ra : 00000000 22768424
    EPC : 22768478, ErrorEPC : 80412AB4, SREG : 500099E3
    MDLO : 87126668, MDHI : D990ADBB, BadVaddr : 00000014
    CacheErr_Icache : 0x007F7F00 - 000040D8, CacheErr_Dcache : 0x00000000 - 00001FA0
    TagLo_Icache : 0x00000000 - 23642303, DataLo_Icache : 0xAFBF0018 - 0D81ADDB
    DataHi_Icache: 0x00000000 - 00000001
    TagLo_Dcache : 0x00000000 - 2277E583, TagHi_Dcache : 0x00000000 - 0912BD81
    DataLo_Dcache: 0x00000001 - 2368110C, DataHi_Dcache : 0x00000000 - 0000001C
    TEXT_START : 0x21003178
    DATA_START : 0x260888A0
    Cause 0000040C (Code 0x3): TLB (store) exception
    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z

    === Flushing messages (22:02:12 UTC Thu Oct 28 2010) ===
    Buffered messages:
    *Oct 28 20:52:40.075: %LINK-3-UPDOWN: Interface SM1/0, changed state to up
    *Oct 28 20:52:42.195: %LINK-3-UPDOWN: Interface GigabitEthernet0/0, changed state to up
    *Oct 28 20:52:42.195: %LINK-3-UPDOWN: Interface GigabitEthernet0/1, changed state to down
    *Oct 28 20:52:42.195: %LINK-3-UPDOWN: Interface GigabitEthernet0/2, changed state to down
    *Oct 28 20:52:44.631: %LINK-3-UPDOWN: Interface SM1/1, changed state to up
    *Oct 28 20:53:01.655: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/0, changed state to up
    *Oct 28 20:53:01.923: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/1, changed state to up
    *Oct 28 20:53:02.075: %LINK-3-UPDOWN: Interface Foreign Exchange Station 0/1/0, changed state to up
    *Oct 28 20:53:02.075: %LINK-3-UPDOWN: Interface Foreign Exchange Station 0/1/1, changed state to up
    *Oct 28 20:53:43.739: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/0, changed state to operational status down due to cable removal
    *Oct 28 20:53:44.739: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/1, changed state to operational status down due to cable removal
    Queued messages:
    No warm reboot Storage
    *** System received a Bus Error exception ***
    signal= 0xa, code= 0x40c, context= 0x29726b74
    PC = 0x22768478, SP = 0x3022fbb8, RA = 0x22768424
    Cause Reg = 0x0000040c, Status Reg = 0x500099e3
    System Bootstrap, Version 15.0(1r)M6, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 2010 by cisco Systems, Inc.
    Total memory size = 512 MB - On-board = 512 MB, DIMM0 = 0 MB
    CISCO2911/K9 platform with 524288 Kbytes of main memory
    Main memory is configured to 72/-1(On-board/DIMM0) bit mode with ECC enabled

    Readonly ROMMON initialized
    program load complete, entry point: 0x80803000, size: 0x1b340

    IOS Image Load Test
    ___________________
    Digitally Signed Development Software
    program load complete, entry point: 0x81000000, size: 0x40b6b74
    Self decompressing the image : #############################################################################################################

    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2691036>
    or simply reply to this email.
    -- --
    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2691978>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2699015>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2699042>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2699089>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2699640>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2704890>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2703353>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2708817>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2712882>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2713045>
    or simply reply to this email.
    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2713062>
    or simply reply to this email.

    Subject: RE: Re: New Message from Radhika Miriyala in Service Ready Engine Virtualiz
    Replied by: Ken Romo on 20-11-2010 01:34:38 AM
    Anurag,
     
    Voice
     
    Ken
     
    What are we using PVDMs for? Voice, video?

    Thanks

    Anurag Gurtu


    Subject: RE: New Message from Radhika Miriyala in Service Ready Engine Virtualizatio
    Replied by: Ken Romo on 20-11-2010 01:34:38 AM
    Radhika,
     
    I have it running with debug on and not sure what I am supposed to be looking for.
    Here is the command you asked me to run:
     
    boxer#sh voice dsp group slot 0
    dsp 1:
      State: UP, firmware: 27.2.0
      Max signal/voice channel: 16/16
      Max credits: 240
      num_of_sig_chnls_allocated: 4
      Transcoding channels allocated: 0
      Group: FLEX_GROUP_VOICE, complexity: FLEX
        Shared credits: 240, reserved credits: 0
        Signaling channels allocated: 4
        Voice channels allocated: 0
        Credits used (rounded-up): 0
      Slot: 0
      Device idx: 0
      PVDM Slot: 0
      Dsp Type: SP2600
     
    Ken,

    Can you try the following to make sure the PVDM is working as expected.


    A) sh voice dsp group slot 0
    dsp 1:
    State: UP, firmware: 28.0.126 <<<< (out put would be something like this)
    ...

    debug vpm dsp

    Thanks,

    Radhika





    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Thursday, November 04, 2010 11:12 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Radhika Miriyala in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Radhika Miriyala has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Ken,

    I think what you did is fine but I will check with IOs team to confirm if they want any additional tests.



    Appreciate your trying all the tests for us.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Thursday, November 04, 2010 11:00 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    The router seemed to work with the PVDM before configuring the sre-v, is there a particular test they would like me to try?

    Ken



    Ken,

    Yes the IOS team was able to reproduce it. They are working on fixing the issue. Also one quick question the IOS team wanted to know was if the have used the PVDM successfully before the using sre-v.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Thursday, November 04, 2010 9:45 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    Do you know if the IOS team has been able to reproduce this yet?

    Thanks in advance,

    Ken Romo


    Ken,

    The IOS team is trying to reproduce this in their setup. I will let you know what the finding are or if we need a debug session with you (if they can¿t reproduce in their setup)



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Wednesday, November 03, 2010 9:03 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    Anything new here today?

    Thanks again,

    Ken



    Ken,

    Right now it looks an IOS bug but we need to reproduce this in house so we can confirm for sure. I will keep you in the loop on what we find. If it turns out to be an issue with this particular PVDM I will let you know.



    Appreciate all your help with this.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Tuesday, November 02, 2010 9:51 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    So what is the root cause?

    The IOS or the PVDMS?

    Do I need to RMA my PVDMS?

    Let me know thank you.

    Ken


    Ken,

    Thanks for the information. We will check internally if this has been tested. I will cancel the debug session for today since we most likely have the root cause for the issue. We will try to reproduce this internally and if we need further information from you will setup a different session.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Tuesday, November 02, 2010 8:49 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    The PVDMS is:

    PVDM3-16 V01
    S/N FOC14200FNK

    Is this what you were looking for?

    Ken


    Ken,

    I am not sure if it is the PVDM that is bad but it could be a bug in the IOS image also where you have pvdm and the SRE module it could be some issue. For now can you continute to do beta for SRE-v without the PVDMS.



    I will check with the team and get back to you as to how to proceed.



    Can you let me know what PVDM models you have so we can try to reproduce this in our lab.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Monday, November 01, 2010 3:59 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    I pulled the PVDM and it is working.

    Does this mean the PVDM is bad?

    Ken


    Ken,

    Please try out the new image sent by Brett to you when you get a chance. Also one difference we noticed is that you have PVDM¿s in your setup that we don not have in our test setup. Would it be possible to remove the PVDMS temporarily and try the ping? This may help us root cause the issue.



    I will also schedule a WebEx for tomorrow morning 10:30 PST with the IOS developer so we can take a look if the change of IOS image and removal of PVDM¿s does not solve the issue. Please let me know if that time slot does not work for you.



    Thanks,

    Radhika





    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Monday, November 01, 2010 11:19 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    Here you go:

    boxer#show vlan-switch
    VLAN Name Status Ports
    ---- -------------------------------- --------- -------------------------------
    1 default active
    1002 fddi-default act/unsup
    1003 token-ring-default act/unsup
    1004 fddinet-default act/unsup
    1005 trnet-default act/unsup
    VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2
    ---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------
    1 enet 100001 1500 - - - - - 1002 1003
    1002 fddi 101002 1500 - - - - - 1 1003
    1003 tr 101003 1500 1005 0 - - srb 1 1002
    1004 fdnet 101004 1500 - - 1 ibm - 0 0
    1005 trnet 101005 1500 - - 1 ibm - 0 0


    boxer#sh platform mgf module
    Registered Module Information
    Code: NR - Not Registered, TM - Trust Mode, SP - Scheduling Profile
    BL - Buffer Level, TR - Traffic Rate, PT - Pause Threshold
    slot vlan type/ID TM SP BL TR PT
    ---- ---- ---------- ------- --- ------ ----- ----
    ISM NR
    EHWIC-0 NR
    EHWIC-1 NR
    EHWIC-2 NR
    EHWIC-3 NR
    PVDM-0 2 PVDM/5 UP 1 low 1000 low
    PVDM-1 2 PVDM/5 UP 1 low 1000 low
    SM-1 1 Switch/3 UP 1 low 1000 high




    Thanks Ken. Can you also give us the output of the following.



    1) show vlan-switch

    2) ¿show platform mgf module¿ before the crash happens.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Monday, November 01, 2010 10:50 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    I will try whatever you suggest, just let me know when you have posted the new IOS.

    Below is my config:

    boxer#sh run
    Building configuration...

    Current configuration : 5777 bytes
    !
    version 15.1
    service timestamps debug datetime msec
    service timestamps log datetime msec
    no service password-encryption
    !
    hostname boxer
    !
    boot-start-marker
    boot system flash0 c2900-universalk9-mz.SSA.151-2.19.T
    boot-end-marker
    !
    !
    logging buffered 51200 warnings
    !
    no aaa new-model
    !
    no ipv6 cef
    ip source-route
    ip cef
    !
    !
    !
    !
    !
    ip domain name yourdomain.com
    multilink bundle-name authenticated
    !
    !
    !
    !
    !
    crypto pki token default removal timeout 0
    !
    crypto pki trustpoint TP-self-signed-1999750280
    enrollment selfsigned
    subject-name cn=IOS-Self-Signed-Certificate-1999750280
    revocation-check none
    rsakeypair TP-self-signed-1999750280
    !
    !
    crypto pki certificate chain TP-self-signed-1999750280
    certificate self-signed 01
    3082024C 308201B5 A0030201 02020101 300D0609 2A864886 F70D0101 04050030
    31312F30 2D060355 04031326 494F532D 53656C66 2D536967 6E65642D 43657274
    69666963 6174652D 31393939 37353032 3830301E 170D3130 31303230 32323335
    32365A17 0D323030 31303130 30303030 305A3031 312F302D 06035504 03132649
    4F532D53 656C662D 5369676E 65642D43 65727469 66696361 74652D31 39393937
    35303238 3030819F 300D0609 2A864886 F70D0101 01050003 818D0030 81890281
    81009378 2E139D79 DCA59865 14AB3398 870362B7 40BB9C13 A5DC5315 6108DF92
    5E78CF06 A40D4DB5 B66D410E FAFE75AC 764997B1 5C551A47 CFA00109 520352EC
    33A69E24 B3C1175B 136FC62A 8BE4637E B834059B FC7CAA6E 957DA0BB 66D8DC49
    80F82890 981FFCFE 0DC7E6F9 53287989 3887C5F6 AF59D0BE B502E11E FD16F556
    DBB90203 010001A3 74307230 0F060355 1D130101 FF040530 030101FF 301F0603
    551D1104 18301682 14626F78 65722E79 6F757264 6F6D6169 6E2E636F 6D301F06
    03551D23 04183016 80143541 7934E424 4B9A60DB E6C908C3 C20BAA17 D058301D
    0603551D 0E041604 14354179 34E4244B 9A60DBE6 C908C3C2 0BAA17D0 58300D06
    092A8648 86F70D01 01040500 03818100 3D222AB5 177D452F 153DCA26 1D7ECB49
    58BCBF60 DA18DC04 94B82EA3 76884EBC D7131641 08687C04 6C6645DF 78B2D2F8
    409BCAD7 50AF5091 B99614FD C2424D89 407A9109 BCA20473 F4CE33D4 4B126483
    C240C0B9 7A628E53 E419FEC3 B8853671 03113F5E 47FA8120 9F9A7A9D 11498FE0
    82C96578 8FD9770A EBD27F73 DF2E1487
    quit
    voice-card 0
    !
    !
    !
    !
    !
    !
    !
    license udi pid CISCO2911/K9 sn FTX1422A077
    hw-module pvdm 0/0
    !
    hw-module sm 1
    !
    !
    !
    username jack privilege 15 secret 5 $1$c5QR$fYGTbhWRKsBZ1JpNyIQGG1
    username marco privilege 15 secret 5 $1$amqq$5pI0T7mUViDL5Y.NqX/yz.
    !
    redundancy
    !
    !
    !
    !
    !
    !
    interface GigabitEthernet0/0
    description To tusqa network
    ip address 172.17.17.130 255.255.248.0
    duplex auto
    speed auto
    !
    interface GigabitEthernet0/1
    no ip address
    shutdown
    duplex auto
    speed auto
    !
    interface GigabitEthernet0/2
    no ip address
    shutdown
    duplex auto
    speed auto
    !
    interface SM1/0
    ip unnumbered GigabitEthernet0/0
    service-module ip address 172.17.17.129 255.255.248.0
    !Application: SRE-V Running on SMV
    service-module ip default-gateway 172.17.17.130
    service-module mgf ip address 10.62.64.1 255.255.255.0
    service-module mgf ip default-gateway 10.62.64.2
    !
    interface SM1/1
    description Internal switch interface connected to Service Module
    switchport mode trunk
    !
    interface Vlan1
    ip address 10.62.64.2 255.255.255.0
    !
    ip forward-protocol nd
    !
    ip http server
    ip http access-class 23
    ip http authentication local
    ip http secure-server
    ip http timeout-policy idle 60 life 86400 requests 10000
    !
    ip route 172.17.17.129 255.255.255.255 SM1/0
    !
    !
    !
    !
    control-plane
    !
    !
    voice-port 0/0/0
    !
    voice-port 0/0/1
    !
    voice-port 0/1/0
    !
    voice-port 0/1/1
    !
    !
    !
    mgcp profile default
    !
    !
    !
    !
    !
    gatekeeper
    shutdown
    !
    !
    banner exec ^C
    % Password expiration warning.
    -----------------------------------------------------------------------
    Cisco Configuration Professional (Cisco CP) is installed on this device
    and it provides the default username "cisco" for one-time use. If you have
    already used the username "cisco" to login to the router and your IOS image
    supports the "one-time" user option, then this username has already expired.
    You will not be able to login to the router with this username after you exit
    this session.
    It is strongly suggested that you create a new username with a privilege level
    of 15 using the following command.
    username <myuser> privilege 15 secret 0 <mypassword>
    Replace <myuser> and <mypassword> with the username and password you want to
    use.
    -----------------------------------------------------------------------
    ^C
    banner login ^C
    -----------------------------------------------------------------------
    Cisco Configuration Professional (Cisco CP) is installed on this device.
    This feature requires the one-time use of the username "cisco" with the
    password "cisco". These default credentials have a privilege level of 15.
    YOU MUST USE CISCO CP or the CISCO IOS CLI TO CHANGE THESE PUBLICLY-KNOWN
    CREDENTIALS
    Here are the Cisco IOS commands.
    username <myuser> privilege 15 secret 0 <mypassword>
    no username cisco
    Replace <myuser> and <mypassword> with the username and password you want
    to use.
    IF YOU DO NOT CHANGE THE PUBLICLY-KNOWN CREDENTIALS, YOU WILL NOT BE ABLE
    TO LOG INTO THE DEVICE AGAIN AFTER YOU HAVE LOGGED OFF.
    For more information about Cisco CP please follow the instructions in the
    QUICK START GUIDE for your router or go to http://www.cisco.com/go/ciscocp
    -----------------------------------------------------------------------
    ^C
    !
    line con 0
    login local
    line aux 0
    line 67
    no activation-character
    no exec
    transport preferred none
    transport input all
    transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
    stopbits 1
    flowcontrol software
    line vty 0 4
    privilege level 15
    login local
    transport input telnet
    line vty 5 15
    privilege level 15
    login local
    transport input telnet ssh
    !
    exception data-corruption buffer truncate
    scheduler allocate 20000 1000
    end



    Ken, Thanks for trying out the image for us. We are trying to reproduce this on our end but have had no luck so far. Can you please send us the output of show running-config from your router.



    Also we have one more image that we would like you to try it out before the debusg session would that be ok?



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Monday, November 01, 2010 10:22 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------

    Radhika,

    I tried the new OS and still getting same IOS crash.
    As mentioned I will work around your schedule so let me if you were able to get someone from the IOS team to help troubleshoot today.

    Thanks in advance,

    Ken Romo


    Ken,

    I am trying to get some help from the IOS team since this a router crash. So I will setup the webex session to debug for some time Monday so we can collect all the information and try out any suggestion from them.



    For Now We will post a newer IOS image to the beta Site and can you give that a try to see if that will solve the issue.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Friday, October 29, 2010 8:24 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    I will work around your schedule, anytime you are available, I will make myself available.
    email:
    kromo@opentext.com

    Thanks in advance,

    Ken Romo

    +++++++++++++++++++++++++++++++++

    Ken,

    Would a webex session tomorrow morning (any time between 10:00 and 1:00) work for you? Let me know the time that would work for you and also your email address so I can send you a webex invite.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Thursday, October 28, 2010 3:12 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Radhika Miriyala in Service Ready Engine Virtualizatio



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    No worries, we are trying to work this out together and I appreciate the help.
    s/m 1/1 is set as trunk but I went ahead and reconfigured to truank again and reloaded OS and get the same crash when I ping to the MGF interface from the SRE (I attached the errors at the bottom of this message).

    Ken,

    Sorry I just realized the mistake. I meant to say make the interface sm 1/1 as trunk.

    Sorry about the confusion.



    Please try it out.



    Thanks,

    Radhika



    boxer#
    %ALIGN-1-FATAL: Illegal access to a low address 22:02:10 UTC Thu Oct 28 2010
    addr=0x14, pc=0x22765BD8z , ra=0x22765B84z , sp=0x3022FBB8
    %ALIGN-1-FATAL: Illegal access to a low address 22:02:11 UTC Thu Oct 28 2010
    addr=0x14, pc=0x22765BD8z , ra=0x22765B84z , sp=0x3022FBB8

    22:02:11 UTC Thu Oct 28 2010: TLB (store) exception, CPU signal 10, PC = 0x22768478

    --------------------------------------------------------------------
    Possible software fault. Upon reccurence, please collect
    crashinfo, "show tech" and contact Cisco Technical Support.
    --------------------------------------------------------------------

    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z
    $0 : 00000000 00000000, AT : 00000000 29130000, v0 : 00000000 00000001, v1 : 00000000 0D8B8540
    a0 : 00000000 00000000, a1 : 00000000 0D8B8584, a2 : 00000000 2A2F8ABC, a3 : 00000000 00000004
    t0 : 00000000 00000020, t1 : 00000000 500099E1, t2 : 00000000 500081E0, t3 : FFFFFFFF FFFFFFF2
    t4 : 00000000 0000000E, t5 : 00000000 00000000, t6 : 00000000 0D95F890, t7 : 00000000 000001FF
    s0 : 00000000 00000000, s1 : 00000000 2A2FDB40, s2 : FFFFFFFF FFFFFFEC, s3 : 00000000 3080C980
    s4 : 00000000 0D95F89E, s5 : 00000000 2A300EE0, s6 : 00000000 00000000, s7 : 00000000 0000000E
    t8 : 00000000 000007FC, t9 : 00000000 2A300200, k0 : 00000000 00000000, k1 : 00000000 00000000
    gp : 00000000 29133C00, sp : 00000000 3022FBB8, s8 : 00000000 00000054, ra : 00000000 22768424
    EPC : 22768478, ErrorEPC : 80412AB4, SREG : 500099E3
    MDLO : 87126668, MDHI : D990ADBB, BadVaddr : 00000014
    CacheErr_Icache : 0x007F7F00 - 000040D8, CacheErr_Dcache : 0x00000000 - 00001FA0
    TagLo_Icache : 0x00000000 - 23642303, DataLo_Icache : 0xAFBF0018 - 0D81ADDB
    DataHi_Icache: 0x00000000 - 00000001
    TagLo_Dcache : 0x00000000 - 2277E583, TagHi_Dcache : 0x00000000 - 0912BD81
    DataLo_Dcache: 0x00000001 - 2368110C, DataHi_Dcache : 0x00000000 - 0000001C
    TEXT_START : 0x21003178
    DATA_START : 0x260888A0
    Cause 0000040C (Code 0x3): TLB (store) exception

    22:02:11 UTC Thu Oct 28 2010: TLB (store) exception, CPU signal 10, PC = 0x22768478

    --------------------------------------------------------------------
    Possible software fault. Upon reccurence, please collect
    crashinfo, "show tech" and contact Cisco Technical Support.
    --------------------------------------------------------------------

    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z
    $0 : 00000000 00000000, AT : 00000000 29130000, v0 : 00000000 00000001, v1 : 00000000 0D8B8540
    a0 : 00000000 00000000, a1 : 00000000 0D8B8584, a2 : 00000000 2A2F8ABC, a3 : 00000000 00000004
    t0 : 00000000 00000020, t1 : 00000000 500099E1, t2 : 00000000 500081E0, t3 : FFFFFFFF FFFFFFF2
    t4 : 00000000 0000000E, t5 : 00000000 00000000, t6 : 00000000 0D95F890, t7 : 00000000 000001FF
    s0 : 00000000 00000000, s1 : 00000000 2A2FDB40, s2 : FFFFFFFF FFFFFFEC, s3 : 00000000 3080C980
    s4 : 00000000 0D95F89E, s5 : 00000000 2A300EE0, s6 : 00000000 00000000, s7 : 00000000 0000000E
    t8 : 00000000 000007FC, t9 : 00000000 2A300200, k0 : 00000000 00000000, k1 : 00000000 00000000
    gp : 00000000 29133C00, sp : 00000000 3022FBB8, s8 : 00000000 00000054, ra : 00000000 22768424
    EPC : 22768478, ErrorEPC : 80412AB4, SREG : 500099E3
    MDLO : 87126668, MDHI : D990ADBB, BadVaddr : 00000014
    CacheErr_Icache : 0x007F7F00 - 000040D8, CacheErr_Dcache : 0x00000000 - 00001FA0
    TagLo_Icache : 0x00000000 - 23642303, DataLo_Icache : 0xAFBF0018 - 0D81ADDB
    DataHi_Icache: 0x00000000 - 00000001
    TagLo_Dcache : 0x00000000 - 2277E583, TagHi_Dcache : 0x00000000 - 0912BD81
    DataLo_Dcache: 0x00000001 - 2368110C, DataHi_Dcache : 0x00000000 - 0000001C
    TEXT_START : 0x21003178
    DATA_START : 0x260888A0
    Cause 0000040C (Code 0x3): TLB (store) exception
    Writing crashinfo to flash:crashinfo_20101028-220211-UTC
    22:02:11 UTC Thu Oct 28 2010: TLB (store) exception, CPU signal 10, PC = 0x22768478

    --------------------------------------------------------------------
    Possible software fault. Upon reccurence, please collect
    crashinfo, "show tech" and contact Cisco Technical Support.
    --------------------------------------------------------------------

    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z
    $0 : 00000000 00000000, AT : 00000000 29130000, v0 : 00000000 00000001, v1 : 00000000 0D8B8540
    a0 : 00000000 00000000, a1 : 00000000 0D8B8584, a2 : 00000000 2A2F8ABC, a3 : 00000000 00000004
    t0 : 00000000 00000020, t1 : 00000000 500099E1, t2 : 00000000 500081E0, t3 : FFFFFFFF FFFFFFF2
    t4 : 00000000 0000000E, t5 : 00000000 00000000, t6 : 00000000 0D95F890, t7 : 00000000 000001FF
    s0 : 00000000 00000000, s1 : 00000000 2A2FDB40, s2 : FFFFFFFF FFFFFFEC, s3 : 00000000 3080C980
    s4 : 00000000 0D95F89E, s5 : 00000000 2A300EE0, s6 : 00000000 00000000, s7 : 00000000 0000000E
    t8 : 00000000 000007FC, t9 : 00000000 2A300200, k0 : 00000000 00000000, k1 : 00000000 00000000
    gp : 00000000 29133C00, sp : 00000000 3022FBB8, s8 : 00000000 00000054, ra : 00000000 22768424
    EPC : 22768478, ErrorEPC : 80412AB4, SREG : 500099E3
    MDLO : 87126668, MDHI : D990ADBB, BadVaddr : 00000014
    CacheErr_Icache : 0x007F7F00 - 000040D8, CacheErr_Dcache : 0x00000000 - 00001FA0
    TagLo_Icache : 0x00000000 - 23642303, DataLo_Icache : 0xAFBF0018 - 0D81ADDB
    DataHi_Icache: 0x00000000 - 00000001
    TagLo_Dcache : 0x00000000 - 2277E583, TagHi_Dcache : 0x00000000 - 0912BD81
    DataLo_Dcache: 0x00000001 - 2368110C, DataHi_Dcache : 0x00000000 - 0000001C
    TEXT_START : 0x21003178
    DATA_START : 0x260888A0
    Cause 0000040C (Code 0x3): TLB (store) exception
    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z

    === Flushing messages (22:02:12 UTC Thu Oct 28 2010) ===
    Buffered messages:
    *Oct 28 20:52:40.075: %LINK-3-UPDOWN: Interface SM1/0, changed state to up
    *Oct 28 20:52:42.195: %LINK-3-UPDOWN: Interface GigabitEthernet0/0, changed state to up
    *Oct 28 20:52:42.195: %LINK-3-UPDOWN: Interface GigabitEthernet0/1, changed state to down
    *Oct 28 20:52:42.195: %LINK-3-UPDOWN: Interface GigabitEthernet0/2, changed state to down
    *Oct 28 20:52:44.631: %LINK-3-UPDOWN: Interface SM1/1, changed state to up
    *Oct 28 20:53:01.655: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/0, changed state to up
    *Oct 28 20:53:01.923: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/1, changed state to up
    *Oct 28 20:53:02.075: %LINK-3-UPDOWN: Interface Foreign Exchange Station 0/1/0, changed state to up
    *Oct 28 20:53:02.075: %LINK-3-UPDOWN: Interface Foreign Exchange Station 0/1/1, changed state to up
    *Oct 28 20:53:43.739: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/0, changed state to operational status down due to cable removal
    *Oct 28 20:53:44.739: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/1, changed state to operational status down due to cable removal
    Queued messages:
    No warm reboot Storage
    *** System received a Bus Error exception ***
    signal= 0xa, code= 0x40c, context= 0x29726b74
    PC = 0x22768478, SP = 0x3022fbb8, RA = 0x22768424
    Cause Reg = 0x0000040c, Status Reg = 0x500099e3
    System Bootstrap, Version 15.0(1r)M6, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 2010 by cisco Systems, Inc.
    Total memory size = 512 MB - On-board = 512 MB, DIMM0 = 0 MB
    CISCO2911/K9 platform with 524288 Kbytes of main memory
    Main memory is configured to 72/-1(On-board/DIMM0) bit mode with ECC enabled

    Readonly ROMMON initialized
    program load complete, entry point: 0x80803000, size: 0x1b340

    IOS Image Load Test
    ___________________
    Digitally Signed Development Software
    program load complete, entry point: 0x81000000, size: 0x40b6b74
    Self decompressing the image : #############################################################################################################

    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2691036>
    or simply reply to this email.
    -- --
    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2691978>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2699015>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2699042>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2699089>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2699640>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2704890>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2703353>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2708817>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2712882>
    or simply reply to this email.
    -- --
    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2713045>
    or simply reply to this email.
    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2713062>
    or simply reply to this email.


    Subject: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-
    Replied by: Radhika Miriyala on 20-11-2010 01:34:38 AM
    Thanks Ken.  The information you have below is good enough.



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Thursday, November 04, 2010 2:26 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Radhika Miriyala in Service Ready Engine Virtualizatio



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    I have it running with debug on and not sure what I am supposed to be looking for.
    Here is the command you asked me to run:

    boxer#sh voice dsp group slot 0
    dsp 1:
      State: UP, firmware: 27.2.0
      Max signal/voice channel: 16/16
      Max credits: 240
      num_of_sig_chnls_allocated: 4
      Transcoding channels allocated: 0
      Group: FLEX_GROUP_VOICE, complexity: FLEX
        Shared credits: 240, reserved credits: 0
        Signaling channels allocated: 4
        Voice channels allocated: 0
        Credits used (rounded-up): 0
      Slot: 0
      Device idx: 0
      PVDM Slot: 0
      Dsp Type: SP2600


    Ken,

    Can you try the following to make sure the PVDM is working as expected.


    A) sh voice dsp group slot 0
    dsp 1:
    State: UP, firmware: 28.0.126 <<<< (out put would be something like this)
    ...

    <http://mce_host/html/js/editor/@theme_images_path@/emoticons/cool.gif> debug vpm dsp

    Thanks,

    Radhika





    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Thursday, November 04, 2010 11:12 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Radhika Miriyala in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Radhika Miriyala has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Ken,

    I think what you did is fine but I will check with IOs team to confirm if they want any additional tests.



    Appreciate your trying all the tests for us.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Thursday, November 04, 2010 11:00 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    The router seemed to work with the PVDM before configuring the sre-v, is there a particular test they would like me to try?

    Ken



    Ken,

    Yes the IOS team was able to reproduce it. They are working on fixing the issue. Also one quick question the IOS team wanted to know was if the have used the PVDM successfully before the using sre-v.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Thursday, November 04, 2010 9:45 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    Do you know if the IOS team has been able to reproduce this yet?

    Thanks in advance,

    Ken Romo


    Ken,

    The IOS team is trying to reproduce this in their setup. I will let you know what the finding are or if we need a debug session with you (if they can¿t reproduce in their setup)



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Wednesday, November 03, 2010 9:03 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    Anything new here today?

    Thanks again,

    Ken



    Ken,

    Right now it looks an IOS bug but we need to reproduce this in house so we can confirm for sure. I will keep you in the loop on what we find. If it turns out to be an issue with this particular PVDM I will let you know.



    Appreciate all your help with this.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Tuesday, November 02, 2010 9:51 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    So what is the root cause?

    The IOS or the PVDMS?

    Do I need to RMA my PVDMS?

    Let me know thank you.

    Ken


    Ken,

    Thanks for the information. We will check internally if this has been tested. I will cancel the debug session for today since we most likely have the root cause for the issue. We will try to reproduce this internally and if we need further information from you will setup a different session.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Tuesday, November 02, 2010 8:49 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    The PVDMS is:

    PVDM3-16 V01
    S/N FOC14200FNK

    Is this what you were looking for?

    Ken


    Ken,

    I am not sure if it is the PVDM that is bad but it could be a bug in the IOS image also where you have pvdm and the SRE module it could be some issue. For now can you continute to do beta for SRE-v without the PVDMS.



    I will check with the team and get back to you as to how to proceed.



    Can you let me know what PVDM models you have so we can try to reproduce this in our lab.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Monday, November 01, 2010 3:59 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    I pulled the PVDM and it is working.

    Does this mean the PVDM is bad?

    Ken


    Ken,

    Please try out the new image sent by Brett to you when you get a chance. Also one difference we noticed is that you have PVDM¿s in your setup that we don not have in our test setup. Would it be possible to remove the PVDMS temporarily and try the ping? This may help us root cause the issue.



    I will also schedule a WebEx for tomorrow morning 10:30 PST with the IOS developer so we can take a look if the change of IOS image and removal of PVDM¿s does not solve the issue. Please let me know if that time slot does not work for you.



    Thanks,

    Radhika





    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Monday, November 01, 2010 11:19 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    Here you go:

    boxer#show vlan-switch
    VLAN Name Status Ports
    ---- -------------------------------- --------- -------------------------------
    1 default active
    1002 fddi-default act/unsup
    1003 token-ring-default act/unsup
    1004 fddinet-default act/unsup
    1005 trnet-default act/unsup
    VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2
    ---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------
    1 enet 100001 1500 - - - - - 1002 1003
    1002 fddi 101002 1500 - - - - - 1 1003
    1003 tr 101003 1500 1005 0 - - srb 1 1002
    1004 fdnet 101004 1500 - - 1 ibm - 0 0
    1005 trnet 101005 1500 - - 1 ibm - 0 0


    boxer#sh platform mgf module
    Registered Module Information
    Code: NR - Not Registered, TM - Trust Mode, SP - Scheduling Profile
    BL - Buffer Level, TR - Traffic Rate, PT - Pause Threshold
    slot vlan type/ID TM SP BL TR PT
    ---- ---- ---------- ------- --- ------ ----- ----
    ISM NR
    EHWIC-0 NR
    EHWIC-1 NR
    EHWIC-2 NR
    EHWIC-3 NR
    PVDM-0 2 PVDM/5 UP 1 low 1000 low
    PVDM-1 2 PVDM/5 UP 1 low 1000 low
    SM-1 1 Switch/3 UP 1 low 1000 high




    Thanks Ken. Can you also give us the output of the following.



    1) show vlan-switch

    2) ¿show platform mgf module¿ before the crash happens.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Monday, November 01, 2010 10:50 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    I will try whatever you suggest, just let me know when you have posted the new IOS.

    Below is my config:

    boxer#sh run
    Building configuration...

    Current configuration : 5777 bytes
    !
    version 15.1
    service timestamps debug datetime msec
    service timestamps log datetime msec
    no service password-encryption
    !
    hostname boxer
    !
    boot-start-marker
    boot system flash0 c2900-universalk9-mz.SSA.151-2.19.T
    boot-end-marker
    !
    !
    logging buffered 51200 warnings
    !
    no aaa new-model
    !
    no ipv6 cef
    ip source-route
    ip cef
    !
    !
    !
    !
    !
    ip domain name yourdomain.com
    multilink bundle-name authenticated
    !
    !
    !
    !
    !
    crypto pki token default removal timeout 0
    !
    crypto pki trustpoint TP-self-signed-1999750280
    enrollment selfsigned
    subject-name cn=IOS-Self-Signed-Certificate-1999750280
    revocation-check none
    rsakeypair TP-self-signed-1999750280
    !
    !
    crypto pki certificate chain TP-self-signed-1999750280
    certificate self-signed 01
    3082024C 308201B5 A0030201 02020101 300D0609 2A864886 F70D0101 04050030
    31312F30 2D060355 04031326 494F532D 53656C66 2D536967 6E65642D 43657274
    69666963 6174652D 31393939 37353032 3830301E 170D3130 31303230 32323335
    32365A17 0D323030 31303130 30303030 305A3031 312F302D 06035504 03132649
    4F532D53 656C662D 5369676E 65642D43 65727469 66696361 74652D31 39393937
    35303238 3030819F 300D0609 2A864886 F70D0101 01050003 818D0030 81890281
    81009378 2E139D79 DCA59865 14AB3398 870362B7 40BB9C13 A5DC5315 6108DF92
    5E78CF06 A40D4DB5 B66D410E FAFE75AC 764997B1 5C551A47 CFA00109 520352EC
    33A69E24 B3C1175B 136FC62A 8BE4637E B834059B FC7CAA6E 957DA0BB 66D8DC49
    80F82890 981FFCFE 0DC7E6F9 53287989 3887C5F6 AF59D0BE B502E11E FD16F556
    DBB90203 010001A3 74307230 0F060355 1D130101 FF040530 030101FF 301F0603
    551D1104 18301682 14626F78 65722E79 6F757264 6F6D6169 6E2E636F 6D301F06
    03551D23 04183016 80143541 7934E424 4B9A60DB E6C908C3 C20BAA17 D058301D
    0603551D 0E041604 14354179 34E4244B 9A60DBE6 C908C3C2 0BAA17D0 58300D06
    092A8648 86F70D01 01040500 03818100 3D222AB5 177D452F 153DCA26 1D7ECB49
    58BCBF60 DA18DC04 94B82EA3 76884EBC D7131641 08687C04 6C6645DF 78B2D2F8
    409BCAD7 50AF5091 B99614FD C2424D89 407A9109 BCA20473 F4CE33D4 4B126483
    C240C0B9 7A628E53 E419FEC3 B8853671 03113F5E 47FA8120 9F9A7A9D 11498FE0
    82C96578 8FD9770A EBD27F73 DF2E1487
    quit
    voice-card 0
    !
    !
    !
    !
    !
    !
    !
    license udi pid CISCO2911/K9 sn FTX1422A077
    hw-module pvdm 0/0
    !
    hw-module sm 1
    !
    !
    !
    username jack privilege 15 secret 5 $1$c5QR$fYGTbhWRKsBZ1JpNyIQGG1
    username marco privilege 15 secret 5 $1$amqq$5pI0T7mUViDL5Y.NqX/yz.
    !
    redundancy
    !
    !
    !
    !
    !
    !
    interface GigabitEthernet0/0
    description To tusqa network
    ip address 172.17.17.130 255.255.248.0
    duplex auto
    speed auto
    !
    interface GigabitEthernet0/1
    no ip address
    shutdown
    duplex auto
    speed auto
    !
    interface GigabitEthernet0/2
    no ip address
    shutdown
    duplex auto
    speed auto
    !
    interface SM1/0
    ip unnumbered GigabitEthernet0/0
    service-module ip address 172.17.17.129 255.255.248.0
    !Application: SRE-V Running on SMV
    service-module ip default-gateway 172.17.17.130
    service-module mgf ip address 10.62.64.1 255.255.255.0
    service-module mgf ip default-gateway 10.62.64.2
    !
    interface SM1/1
    description Internal switch interface connected to Service Module
    switchport mode trunk
    !
    interface Vlan1
    ip address 10.62.64.2 255.255.255.0
    !
    ip forward-protocol nd
    !
    ip http server
    ip http access-class 23
    ip http authentication local
    ip http secure-server
    ip http timeout-policy idle 60 life 86400 requests 10000
    !
    ip route 172.17.17.129 255.255.255.255 SM1/0
    !
    !
    !
    !
    control-plane
    !
    !
    voice-port 0/0/0
    !
    voice-port 0/0/1
    !
    voice-port 0/1/0
    !
    voice-port 0/1/1
    !
    !
    !
    mgcp profile default
    !
    !
    !
    !
    !
    gatekeeper
    shutdown
    !
    !
    banner exec ^C
    % Password expiration warning.
    -----------------------------------------------------------------------
    Cisco Configuration Professional (Cisco CP) is installed on this device
    and it provides the default username "cisco" for one-time use. If you have
    already used the username "cisco" to login to the router and your IOS image
    supports the "one-time" user option, then this username has already expired.
    You will not be able to login to the router with this username after you exit
    this session.
    It is strongly suggested that you create a new username with a privilege level
    of 15 using the following command.
    username <myuser> privilege 15 secret 0 <mypassword>
    Replace <myuser> and <mypassword> with the username and password you want to
    use.
    -----------------------------------------------------------------------
    ^C
    banner login ^C
    -----------------------------------------------------------------------
    Cisco Configuration Professional (Cisco CP) is installed on this device.
    This feature requires the one-time use of the username "cisco" with the
    password "cisco". These default credentials have a privilege level of 15.
    YOU MUST USE CISCO CP or the CISCO IOS CLI TO CHANGE THESE PUBLICLY-KNOWN
    CREDENTIALS
    Here are the Cisco IOS commands.
    username <myuser> privilege 15 secret 0 <mypassword>
    no username cisco
    Replace <myuser> and <mypassword> with the username and password you want
    to use.
    IF YOU DO NOT CHANGE THE PUBLICLY-KNOWN CREDENTIALS, YOU WILL NOT BE ABLE
    TO LOG INTO THE DEVICE AGAIN AFTER YOU HAVE LOGGED OFF.
    For more information about Cisco CP please follow the instructions in the
    QUICK START GUIDE for your router or go to http://www.cisco.com/go/ciscocp
    -----------------------------------------------------------------------
    ^C
    !
    line con 0
    login local
    line aux 0
    line 67
    no activation-character
    no exec
    transport preferred none
    transport input all
    transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
    stopbits 1
    flowcontrol software
    line vty 0 4
    privilege level 15
    login local
    transport input telnet
    line vty 5 15
    privilege level 15
    login local
    transport input telnet ssh
    !
    exception data-corruption buffer truncate
    scheduler allocate 20000 1000
    end



    Ken, Thanks for trying out the image for us. We are trying to reproduce this on our end but have had no luck so far. Can you please send us the output of show running-config from your router.



    Also we have one more image that we would like you to try it out before the debusg session would that be ok?



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Monday, November 01, 2010 10:22 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------

    Radhika,

    I tried the new OS and still getting same IOS crash.
    As mentioned I will work around your schedule so let me if you were able to get someone from the IOS team to help troubleshoot today.

    Thanks in advance,

    Ken Romo


    Ken,

    I am trying to get some help from the IOS team since this a router crash. So I will setup the webex session to debug for some time Monday so we can collect all the information and try out any suggestion from them.



    For Now We will post a newer IOS image to the beta Site and can you give that a try to see if that will solve the issue.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Friday, October 29, 2010 8:24 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    I will work around your schedule, anytime you are available, I will make myself available.
    email:
    kromo@opentext.com

    Thanks in advance,

    Ken Romo

    +++++++++++++++++++++++++++++++++

    Ken,

    Would a webex session tomorrow morning (any time between 10:00 and 1:00) work for you? Let me know the time that would work for you and also your email address so I can send you a webex invite.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Thursday, October 28, 2010 3:12 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Radhika Miriyala in Service Ready Engine Virtualizatio



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    No worries, we are trying to work this out together and I appreciate the help.
    s/m 1/1 is set as trunk but I went ahead and reconfigured to truank again and reloaded OS and get the same crash when I ping to the MGF interface from the SRE (I attached the errors at the bottom of this message).

    Ken,

    Sorry I just realized the mistake. I meant to say make the interface sm 1/1 as trunk.

    Sorry about the confusion.



    Please try it out.



    Thanks,

    Radhika



    boxer#
    %ALIGN-1-FATAL: Illegal access to a low address 22:02:10 UTC Thu Oct 28 2010
    addr=0x14, pc=0x22765BD8z , ra=0x22765B84z , sp=0x3022FBB8
    %ALIGN-1-FATAL: Illegal access to a low address 22:02:11 UTC Thu Oct 28 2010
    addr=0x14, pc=0x22765BD8z , ra=0x22765B84z , sp=0x3022FBB8

    22:02:11 UTC Thu Oct 28 2010: TLB (store) exception, CPU signal 10, PC = 0x22768478

    --------------------------------------------------------------------
    Possible software fault. Upon reccurence, please collect
    crashinfo, "show tech" and contact Cisco Technical Support.
    --------------------------------------------------------------------

    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z
    $0 : 00000000 00000000, AT : 00000000 29130000, v0 : 00000000 00000001, v1 : 00000000 0D8B8540
    a0 : 00000000 00000000, a1 : 00000000 0D8B8584, a2 : 00000000 2A2F8ABC, a3 : 00000000 00000004
    t0 : 00000000 00000020, t1 : 00000000 500099E1, t2 : 00000000 500081E0, t3 : FFFFFFFF FFFFFFF2
    t4 : 00000000 0000000E, t5 : 00000000 00000000, t6 : 00000000 0D95F890, t7 : 00000000 000001FF
    s0 : 00000000 00000000, s1 : 00000000 2A2FDB40, s2 : FFFFFFFF FFFFFFEC, s3 : 00000000 3080C980
    s4 : 00000000 0D95F89E, s5 : 00000000 2A300EE0, s6 : 00000000 00000000, s7 : 00000000 0000000E
    t8 : 00000000 000007FC, t9 : 00000000 2A300200, k0 : 00000000 00000000, k1 : 00000000 00000000
    gp : 00000000 29133C00, sp : 00000000 3022FBB8, s8 : 00000000 00000054, ra : 00000000 22768424
    EPC : 22768478, ErrorEPC : 80412AB4, SREG : 500099E3
    MDLO : 87126668, MDHI : D990ADBB, BadVaddr : 00000014
    CacheErr_Icache : 0x007F7F00 - 000040D8, CacheErr_Dcache : 0x00000000 - 00001FA0
    TagLo_Icache : 0x00000000 - 23642303, DataLo_Icache : 0xAFBF0018 - 0D81ADDB
    DataHi_Icache: 0x00000000 - 00000001
    TagLo_Dcache : 0x00000000 - 2277E583, TagHi_Dcache : 0x00000000 - 0912BD81
    DataLo_Dcache: 0x00000001 - 2368110C, DataHi_Dcache : 0x00000000 - 0000001C
    TEXT_START : 0x21003178
    DATA_START : 0x260888A0
    Cause 0000040C (Code 0x3): TLB (store) exception

    22:02:11 UTC Thu Oct 28 2010: TLB (store) exception, CPU signal 10, PC = 0x22768478

    --------------------------------------------------------------------
    Possible software fault. Upon reccurence, please collect
    crashinfo, "show tech" and contact Cisco Technical Support.
    --------------------------------------------------------------------

    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z
    $0 : 00000000 00000000, AT : 00000000 29130000, v0 : 00000000 00000001, v1 : 00000000 0D8B8540
    a0 : 00000000 00000000, a1 : 00000000 0D8B8584, a2 : 00000000 2A2F8ABC, a3 : 00000000 00000004
    t0 : 00000000 00000020, t1 : 00000000 500099E1, t2 : 00000000 500081E0, t3 : FFFFFFFF FFFFFFF2
    t4 : 00000000 0000000E, t5 : 00000000 00000000, t6 : 00000000 0D95F890, t7 : 00000000 000001FF
    s0 : 00000000 00000000, s1 : 00000000 2A2FDB40, s2 : FFFFFFFF FFFFFFEC, s3 : 00000000 3080C980
    s4 : 00000000 0D95F89E, s5 : 00000000 2A300EE0, s6 : 00000000 00000000, s7 : 00000000 0000000E
    t8 : 00000000 000007FC, t9 : 00000000 2A300200, k0 : 00000000 00000000, k1 : 00000000 00000000
    gp : 00000000 29133C00, sp : 00000000 3022FBB8, s8 : 00000000 00000054, ra : 00000000 22768424
    EPC : 22768478, ErrorEPC : 80412AB4, SREG : 500099E3
    MDLO : 87126668, MDHI : D990ADBB, BadVaddr : 00000014
    CacheErr_Icache : 0x007F7F00 - 000040D8, CacheErr_Dcache : 0x00000000 - 00001FA0
    TagLo_Icache : 0x00000000 - 23642303, DataLo_Icache : 0xAFBF0018 - 0D81ADDB
    DataHi_Icache: 0x00000000 - 00000001
    TagLo_Dcache : 0x00000000 - 2277E583, TagHi_Dcache : 0x00000000 - 0912BD81
    DataLo_Dcache: 0x00000001 - 2368110C, DataHi_Dcache : 0x00000000 - 0000001C
    TEXT_START : 0x21003178
    DATA_START : 0x260888A0
    Cause 0000040C (Code 0x3): TLB (store) exception
    Writing crashinfo to flash:crashinfo_20101028-220211-UTC
    22:02:11 UTC Thu Oct 28 2010: TLB (store) exception, CPU signal 10, PC = 0x22768478

    --------------------------------------------------------------------
    Possible software fault. Upon reccurence, please collect
    crashinfo, "show tech" and contact Cisco Technical Support.
    --------------------------------------------------------------------

    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z
    $0 : 00000000 00000000, AT : 00000000 29130000, v0 : 00000000 00000001, v1 : 00000000 0D8B8540
    a0 : 00000000 00000000, a1 : 00000000 0D8B8584, a2 : 00000000 2A2F8ABC, a3 : 00000000 00000004
    t0 : 00000000 00000020, t1 : 00000000 500099E1, t2 : 00000000 500081E0, t3 : FFFFFFFF FFFFFFF2
    t4 : 00000000 0000000E, t5 : 00000000 00000000, t6 : 00000000 0D95F890, t7 : 00000000 000001FF
    s0 : 00000000 00000000, s1 : 00000000 2A2FDB40, s2 : FFFFFFFF FFFFFFEC, s3 : 00000000 3080C980
    s4 : 00000000 0D95F89E, s5 : 00000000 2A300EE0, s6 : 00000000 00000000, s7 : 00000000 0000000E
    t8 : 00000000 000007FC, t9 : 00000000 2A300200, k0 : 00000000 00000000, k1 : 00000000 00000000
    gp : 00000000 29133C00, sp : 00000000 3022FBB8, s8 : 00000000 00000054, ra : 00000000 22768424
    EPC : 22768478, ErrorEPC : 80412AB4, SREG : 500099E3
    MDLO : 87126668, MDHI : D990ADBB, BadVaddr : 00000014
    CacheErr_Icache : 0x007F7F00 - 000040D8, CacheErr_Dcache : 0x00000000 - 00001FA0
    TagLo_Icache : 0x00000000 - 23642303, DataLo_Icache : 0xAFBF0018 - 0D81ADDB
    DataHi_Icache: 0x00000000 - 00000001
    TagLo_Dcache : 0x00000000 - 2277E583, TagHi_Dcache : 0x00000000 - 0912BD81
    DataLo_Dcache: 0x00000001 - 2368110C, DataHi_Dcache : 0x00000000 - 0000001C
    TEXT_START : 0x21003178
    DATA_START : 0x260888A0
    Cause 0000040C (Code 0x3): TLB (store) exception
    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z

    === Flushing messages (22:02:12 UTC Thu Oct 28 2010) ===
    Buffered messages:
    *Oct 28 20:52:40.075: %LINK-3-UPDOWN: Interface SM1/0, changed state to up
    *Oct 28 20:52:42.195: %LINK-3-UPDOWN: Interface GigabitEthernet0/0, changed state to up
    *Oct 28 20:52:42.195: %LINK-3-UPDOWN: Interface GigabitEthernet0/1, changed state to down
    *Oct 28 20:52:42.195: %LINK-3-UPDOWN: Interface GigabitEthernet0/2, changed state to down
    *Oct 28 20:52:44.631: %LINK-3-UPDOWN: Interface SM1/1, changed state to up
    *Oct 28 20:53:01.655: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/0, changed state to up
    *Oct 28 20:53:01.923: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/1, changed state to up
    *Oct 28 20:53:02.075: %LINK-3-UPDOWN: Interface Foreign Exchange Station 0/1/0, changed state to up
    *Oct 28 20:53:02.075: %LINK-3-UPDOWN: Interface Foreign Exchange Station 0/1/1, changed state to up
    *Oct 28 20:53:43.739: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/0, changed state to operational status down due to cable removal
    *Oct 28 20:53:44.739: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/1, changed state to operational status down due to cable removal
    Queued messages:
    No warm reboot Storage
    *** System received a Bus Error exception ***
    signal= 0xa, code= 0x40c, context= 0x29726b74
    PC = 0x22768478, SP = 0x3022fbb8, RA = 0x22768424
    Cause Reg = 0x0000040c, Status Reg = 0x500099e3
    System Bootstrap, Version 15.0(1r)M6, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 2010 by cisco Systems, Inc.
    Total memory size = 512 MB - On-board = 512 MB, DIMM0 = 0 MB
    CISCO2911/K9 platform with 524288 Kbytes of main memory
    Main memory is configured to 72/-1(On-board/DIMM0) bit mode with ECC enabled

    Readonly ROMMON initialized
    program load complete, entry point: 0x80803000, size: 0x1b340

    IOS Image Load Test
    ___________________
    Digitally Signed Development Software
    program load complete, entry point: 0x81000000, size: 0x40b6b74
    Self decompressing the image : #############################################################################################################

    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2691036>
    or simply reply to this email.
    -- --
    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2691978>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2699015>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2699042>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2699089>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2699640>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2704890>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2703353>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2708817>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2712882>
    or simply reply to this email.
    -- --
    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2713045>
    or simply reply to this email.
    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2713062>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2713416>
    or simply reply to this email.

    Subject: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-
    Replied by: Ken Romo on 20-11-2010 01:34:39 AM
    Radhika,
     
    Any new status today on new IOS?
     
    Thanks in advance,
     
    Ken
     
    Thanks Ken. The information you have below is good enough.



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Thursday, November 04, 2010 2:26 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Radhika Miriyala in Service Ready Engine Virtualizatio



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    I have it running with debug on and not sure what I am supposed to be looking for.
    Here is the command you asked me to run:

    boxer#sh voice dsp group slot 0
    dsp 1:
    State: UP, firmware: 27.2.0
    Max signal/voice channel: 16/16
    Max credits: 240
    num_of_sig_chnls_allocated: 4
    Transcoding channels allocated: 0
    Group: FLEX_GROUP_VOICE, complexity: FLEX
    Shared credits: 240, reserved credits: 0
    Signaling channels allocated: 4
    Voice channels allocated: 0
    Credits used (rounded-up): 0
    Slot: 0
    Device idx: 0
    PVDM Slot: 0
    Dsp Type: SP2600


    Ken,

    Can you try the following to make sure the PVDM is working as expected.


    A) sh voice dsp group slot 0
    dsp 1:
    State: UP, firmware: 28.0.126 <<<< (out put would be something like this)
    ...

    <http://mce_host/html/js/editor/@theme_images_path@/emoticons/cool.gif> debug vpm dsp

    Thanks,

    Radhika





    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Thursday, November 04, 2010 11:12 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Radhika Miriyala in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Radhika Miriyala has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Ken,

    I think what you did is fine but I will check with IOs team to confirm if they want any additional tests.



    Appreciate your trying all the tests for us.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Thursday, November 04, 2010 11:00 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    The router seemed to work with the PVDM before configuring the sre-v, is there a particular test they would like me to try?

    Ken



    Ken,

    Yes the IOS team was able to reproduce it. They are working on fixing the issue. Also one quick question the IOS team wanted to know was if the have used the PVDM successfully before the using sre-v.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Thursday, November 04, 2010 9:45 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    Do you know if the IOS team has been able to reproduce this yet?

    Thanks in advance,

    Ken Romo


    Ken,

    The IOS team is trying to reproduce this in their setup. I will let you know what the finding are or if we need a debug session with you (if they can¿t reproduce in their setup)



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Wednesday, November 03, 2010 9:03 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    Anything new here today?

    Thanks again,

    Ken



    Ken,

    Right now it looks an IOS bug but we need to reproduce this in house so we can confirm for sure. I will keep you in the loop on what we find. If it turns out to be an issue with this particular PVDM I will let you know.



    Appreciate all your help with this.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Tuesday, November 02, 2010 9:51 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    So what is the root cause?

    The IOS or the PVDMS?

    Do I need to RMA my PVDMS?

    Let me know thank you.

    Ken


    Ken,

    Thanks for the information. We will check internally if this has been tested. I will cancel the debug session for today since we most likely have the root cause for the issue. We will try to reproduce this internally and if we need further information from you will setup a different session.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Tuesday, November 02, 2010 8:49 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    The PVDMS is:

    PVDM3-16 V01
    S/N FOC14200FNK

    Is this what you were looking for?

    Ken


    Ken,

    I am not sure if it is the PVDM that is bad but it could be a bug in the IOS image also where you have pvdm and the SRE module it could be some issue. For now can you continute to do beta for SRE-v without the PVDMS.



    I will check with the team and get back to you as to how to proceed.



    Can you let me know what PVDM models you have so we can try to reproduce this in our lab.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Monday, November 01, 2010 3:59 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    I pulled the PVDM and it is working.

    Does this mean the PVDM is bad?

    Ken


    Ken,

    Please try out the new image sent by Brett to you when you get a chance. Also one difference we noticed is that you have PVDM¿s in your setup that we don not have in our test setup. Would it be possible to remove the PVDMS temporarily and try the ping? This may help us root cause the issue.



    I will also schedule a WebEx for tomorrow morning 10:30 PST with the IOS developer so we can take a look if the change of IOS image and removal of PVDM¿s does not solve the issue. Please let me know if that time slot does not work for you.



    Thanks,

    Radhika





    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Monday, November 01, 2010 11:19 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    Here you go:

    boxer#show vlan-switch
    VLAN Name Status Ports
    ---- -------------------------------- --------- -------------------------------
    1 default active
    1002 fddi-default act/unsup
    1003 token-ring-default act/unsup
    1004 fddinet-default act/unsup
    1005 trnet-default act/unsup
    VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2
    ---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------
    1 enet 100001 1500 - - - - - 1002 1003
    1002 fddi 101002 1500 - - - - - 1 1003
    1003 tr 101003 1500 1005 0 - - srb 1 1002
    1004 fdnet 101004 1500 - - 1 ibm - 0 0
    1005 trnet 101005 1500 - - 1 ibm - 0 0


    boxer#sh platform mgf module
    Registered Module Information
    Code: NR - Not Registered, TM - Trust Mode, SP - Scheduling Profile
    BL - Buffer Level, TR - Traffic Rate, PT - Pause Threshold
    slot vlan type/ID TM SP BL TR PT
    ---- ---- ---------- ------- --- ------ ----- ----
    ISM NR
    EHWIC-0 NR
    EHWIC-1 NR
    EHWIC-2 NR
    EHWIC-3 NR
    PVDM-0 2 PVDM/5 UP 1 low 1000 low
    PVDM-1 2 PVDM/5 UP 1 low 1000 low
    SM-1 1 Switch/3 UP 1 low 1000 high




    Thanks Ken. Can you also give us the output of the following.



    1) show vlan-switch

    2) ¿show platform mgf module¿ before the crash happens.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Monday, November 01, 2010 10:50 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    I will try whatever you suggest, just let me know when you have posted the new IOS.

    Below is my config:

    boxer#sh run
    Building configuration...

    Current configuration : 5777 bytes
    !
    version 15.1
    service timestamps debug datetime msec
    service timestamps log datetime msec
    no service password-encryption
    !
    hostname boxer
    !
    boot-start-marker
    boot system flash0 c2900-universalk9-mz.SSA.151-2.19.T
    boot-end-marker
    !
    !
    logging buffered 51200 warnings
    !
    no aaa new-model
    !
    no ipv6 cef
    ip source-route
    ip cef
    !
    !
    !
    !
    !
    ip domain name yourdomain.com
    multilink bundle-name authenticated
    !
    !
    !
    !
    !
    crypto pki token default removal timeout 0
    !
    crypto pki trustpoint TP-self-signed-1999750280
    enrollment selfsigned
    subject-name cn=IOS-Self-Signed-Certificate-1999750280
    revocation-check none
    rsakeypair TP-self-signed-1999750280
    !
    !
    crypto pki certificate chain TP-self-signed-1999750280
    certificate self-signed 01
    3082024C 308201B5 A0030201 02020101 300D0609 2A864886 F70D0101 04050030
    31312F30 2D060355 04031326 494F532D 53656C66 2D536967 6E65642D 43657274
    69666963 6174652D 31393939 37353032 3830301E 170D3130 31303230 32323335
    32365A17 0D323030 31303130 30303030 305A3031 312F302D 06035504 03132649
    4F532D53 656C662D 5369676E 65642D43 65727469 66696361 74652D31 39393937
    35303238 3030819F 300D0609 2A864886 F70D0101 01050003 818D0030 81890281
    81009378 2E139D79 DCA59865 14AB3398 870362B7 40BB9C13 A5DC5315 6108DF92
    5E78CF06 A40D4DB5 B66D410E FAFE75AC 764997B1 5C551A47 CFA00109 520352EC
    33A69E24 B3C1175B 136FC62A 8BE4637E B834059B FC7CAA6E 957DA0BB 66D8DC49
    80F82890 981FFCFE 0DC7E6F9 53287989 3887C5F6 AF59D0BE B502E11E FD16F556
    DBB90203 010001A3 74307230 0F060355 1D130101 FF040530 030101FF 301F0603
    551D1104 18301682 14626F78 65722E79 6F757264 6F6D6169 6E2E636F 6D301F06
    03551D23 04183016 80143541 7934E424 4B9A60DB E6C908C3 C20BAA17 D058301D
    0603551D 0E041604 14354179 34E4244B 9A60DBE6 C908C3C2 0BAA17D0 58300D06
    092A8648 86F70D01 01040500 03818100 3D222AB5 177D452F 153DCA26 1D7ECB49
    58BCBF60 DA18DC04 94B82EA3 76884EBC D7131641 08687C04 6C6645DF 78B2D2F8
    409BCAD7 50AF5091 B99614FD C2424D89 407A9109 BCA20473 F4CE33D4 4B126483
    C240C0B9 7A628E53 E419FEC3 B8853671 03113F5E 47FA8120 9F9A7A9D 11498FE0
    82C96578 8FD9770A EBD27F73 DF2E1487
    quit
    voice-card 0
    !
    !
    !
    !
    !
    !
    !
    license udi pid CISCO2911/K9 sn FTX1422A077
    hw-module pvdm 0/0
    !
    hw-module sm 1
    !
    !
    !
    username jack privilege 15 secret 5 $1$c5QR$fYGTbhWRKsBZ1JpNyIQGG1
    username marco privilege 15 secret 5 $1$amqq$5pI0T7mUViDL5Y.NqX/yz.
    !
    redundancy
    !
    !
    !
    !
    !
    !
    interface GigabitEthernet0/0
    description To tusqa network
    ip address 172.17.17.130 255.255.248.0
    duplex auto
    speed auto
    !
    interface GigabitEthernet0/1
    no ip address
    shutdown
    duplex auto
    speed auto
    !
    interface GigabitEthernet0/2
    no ip address
    shutdown
    duplex auto
    speed auto
    !
    interface SM1/0
    ip unnumbered GigabitEthernet0/0
    service-module ip address 172.17.17.129 255.255.248.0
    !Application: SRE-V Running on SMV
    service-module ip default-gateway 172.17.17.130
    service-module mgf ip address 10.62.64.1 255.255.255.0
    service-module mgf ip default-gateway 10.62.64.2
    !
    interface SM1/1
    description Internal switch interface connected to Service Module
    switchport mode trunk
    !
    interface Vlan1
    ip address 10.62.64.2 255.255.255.0
    !
    ip forward-protocol nd
    !
    ip http server
    ip http access-class 23
    ip http authentication local
    ip http secure-server
    ip http timeout-policy idle 60 life 86400 requests 10000
    !
    ip route 172.17.17.129 255.255.255.255 SM1/0
    !
    !
    !
    !
    control-plane
    !
    !
    voice-port 0/0/0
    !
    voice-port 0/0/1
    !
    voice-port 0/1/0
    !
    voice-port 0/1/1
    !
    !
    !
    mgcp profile default
    !
    !
    !
    !
    !
    gatekeeper
    shutdown
    !
    !
    banner exec ^C
    % Password expiration warning.
    -----------------------------------------------------------------------
    Cisco Configuration Professional (Cisco CP) is installed on this device
    and it provides the default username "cisco" for one-time use. If you have
    already used the username "cisco" to login to the router and your IOS image
    supports the "one-time" user option, then this username has already expired.
    You will not be able to login to the router with this username after you exit
    this session.
    It is strongly suggested that you create a new username with a privilege level
    of 15 using the following command.
    username <myuser> privilege 15 secret 0 <mypassword>
    Replace <myuser> and <mypassword> with the username and password you want to
    use.
    -----------------------------------------------------------------------
    ^C
    banner login ^C
    -----------------------------------------------------------------------
    Cisco Configuration Professional (Cisco CP) is installed on this device.
    This feature requires the one-time use of the username "cisco" with the
    password "cisco". These default credentials have a privilege level of 15.
    YOU MUST USE CISCO CP or the CISCO IOS CLI TO CHANGE THESE PUBLICLY-KNOWN
    CREDENTIALS
    Here are the Cisco IOS commands.
    username <myuser> privilege 15 secret 0 <mypassword>
    no username cisco
    Replace <myuser> and <mypassword> with the username and password you want
    to use.
    IF YOU DO NOT CHANGE THE PUBLICLY-KNOWN CREDENTIALS, YOU WILL NOT BE ABLE
    TO LOG INTO THE DEVICE AGAIN AFTER YOU HAVE LOGGED OFF.
    For more information about Cisco CP please follow the instructions in the
    QUICK START GUIDE for your router or go to http://www.cisco.com/go/ciscocp
    -----------------------------------------------------------------------
    ^C
    !
    line con 0
    login local
    line aux 0
    line 67
    no activation-character
    no exec
    transport preferred none
    transport input all
    transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
    stopbits 1
    flowcontrol software
    line vty 0 4
    privilege level 15
    login local
    transport input telnet
    line vty 5 15
    privilege level 15
    login local
    transport input telnet ssh
    !
    exception data-corruption buffer truncate
    scheduler allocate 20000 1000
    end



    Ken, Thanks for trying out the image for us. We are trying to reproduce this on our end but have had no luck so far. Can you please send us the output of show running-config from your router.



    Also we have one more image that we would like you to try it out before the debusg session would that be ok?



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Monday, November 01, 2010 10:22 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------

    Radhika,

    I tried the new OS and still getting same IOS crash.
    As mentioned I will work around your schedule so let me if you were able to get someone from the IOS team to help troubleshoot today.

    Thanks in advance,

    Ken Romo


    Ken,

    I am trying to get some help from the IOS team since this a router crash. So I will setup the webex session to debug for some time Monday so we can collect all the information and try out any suggestion from them.



    For Now We will post a newer IOS image to the beta Site and can you give that a try to see if that will solve the issue.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Friday, October 29, 2010 8:24 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    I will work around your schedule, anytime you are available, I will make myself available.
    email:
    kromo@opentext.com

    Thanks in advance,

    Ken Romo

    +++++++++++++++++++++++++++++++++

    Ken,

    Would a webex session tomorrow morning (any time between 10:00 and 1:00) work for you? Let me know the time that would work for you and also your email address so I can send you a webex invite.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Thursday, October 28, 2010 3:12 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Radhika Miriyala in Service Ready Engine Virtualizatio



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    No worries, we are trying to work this out together and I appreciate the help.
    s/m 1/1 is set as trunk but I went ahead and reconfigured to truank again and reloaded OS and get the same crash when I ping to the MGF interface from the SRE (I attached the errors at the bottom of this message).

    Ken,

    Sorry I just realized the mistake. I meant to say make the interface sm 1/1 as trunk.

    Sorry about the confusion.



    Please try it out.



    Thanks,

    Radhika



    boxer#
    %ALIGN-1-FATAL: Illegal access to a low address 22:02:10 UTC Thu Oct 28 2010
    addr=0x14, pc=0x22765BD8z , ra=0x22765B84z , sp=0x3022FBB8
    %ALIGN-1-FATAL: Illegal access to a low address 22:02:11 UTC Thu Oct 28 2010
    addr=0x14, pc=0x22765BD8z , ra=0x22765B84z , sp=0x3022FBB8

    22:02:11 UTC Thu Oct 28 2010: TLB (store) exception, CPU signal 10, PC = 0x22768478

    --------------------------------------------------------------------
    Possible software fault. Upon reccurence, please collect
    crashinfo, "show tech" and contact Cisco Technical Support.
    --------------------------------------------------------------------

    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z
    $0 : 00000000 00000000, AT : 00000000 29130000, v0 : 00000000 00000001, v1 : 00000000 0D8B8540
    a0 : 00000000 00000000, a1 : 00000000 0D8B8584, a2 : 00000000 2A2F8ABC, a3 : 00000000 00000004
    t0 : 00000000 00000020, t1 : 00000000 500099E1, t2 : 00000000 500081E0, t3 : FFFFFFFF FFFFFFF2
    t4 : 00000000 0000000E, t5 : 00000000 00000000, t6 : 00000000 0D95F890, t7 : 00000000 000001FF
    s0 : 00000000 00000000, s1 : 00000000 2A2FDB40, s2 : FFFFFFFF FFFFFFEC, s3 : 00000000 3080C980
    s4 : 00000000 0D95F89E, s5 : 00000000 2A300EE0, s6 : 00000000 00000000, s7 : 00000000 0000000E
    t8 : 00000000 000007FC, t9 : 00000000 2A300200, k0 : 00000000 00000000, k1 : 00000000 00000000
    gp : 00000000 29133C00, sp : 00000000 3022FBB8, s8 : 00000000 00000054, ra : 00000000 22768424
    EPC : 22768478, ErrorEPC : 80412AB4, SREG : 500099E3
    MDLO : 87126668, MDHI : D990ADBB, BadVaddr : 00000014
    CacheErr_Icache : 0x007F7F00 - 000040D8, CacheErr_Dcache : 0x00000000 - 00001FA0
    TagLo_Icache : 0x00000000 - 23642303, DataLo_Icache : 0xAFBF0018 - 0D81ADDB
    DataHi_Icache: 0x00000000 - 00000001
    TagLo_Dcache : 0x00000000 - 2277E583, TagHi_Dcache : 0x00000000 - 0912BD81
    DataLo_Dcache: 0x00000001 - 2368110C, DataHi_Dcache : 0x00000000 - 0000001C
    TEXT_START : 0x21003178
    DATA_START : 0x260888A0
    Cause 0000040C (Code 0x3): TLB (store) exception

    22:02:11 UTC Thu Oct 28 2010: TLB (store) exception, CPU signal 10, PC = 0x22768478

    --------------------------------------------------------------------
    Possible software fault. Upon reccurence, please collect
    crashinfo, "show tech" and contact Cisco Technical Support.
    --------------------------------------------------------------------

    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z
    $0 : 00000000 00000000, AT : 00000000 29130000, v0 : 00000000 00000001, v1 : 00000000 0D8B8540
    a0 : 00000000 00000000, a1 : 00000000 0D8B8584, a2 : 00000000 2A2F8ABC, a3 : 00000000 00000004
    t0 : 00000000 00000020, t1 : 00000000 500099E1, t2 : 00000000 500081E0, t3 : FFFFFFFF FFFFFFF2
    t4 : 00000000 0000000E, t5 : 00000000 00000000, t6 : 00000000 0D95F890, t7 : 00000000 000001FF
    s0 : 00000000 00000000, s1 : 00000000 2A2FDB40, s2 : FFFFFFFF FFFFFFEC, s3 : 00000000 3080C980
    s4 : 00000000 0D95F89E, s5 : 00000000 2A300EE0, s6 : 00000000 00000000, s7 : 00000000 0000000E
    t8 : 00000000 000007FC, t9 : 00000000 2A300200, k0 : 00000000 00000000, k1 : 00000000 00000000
    gp : 00000000 29133C00, sp : 00000000 3022FBB8, s8 : 00000000 00000054, ra : 00000000 22768424
    EPC : 22768478, ErrorEPC : 80412AB4, SREG : 500099E3
    MDLO : 87126668, MDHI : D990ADBB, BadVaddr : 00000014
    CacheErr_Icache : 0x007F7F00 - 000040D8, CacheErr_Dcache : 0x00000000 - 00001FA0
    TagLo_Icache : 0x00000000 - 23642303, DataLo_Icache : 0xAFBF0018 - 0D81ADDB
    DataHi_Icache: 0x00000000 - 00000001
    TagLo_Dcache : 0x00000000 - 2277E583, TagHi_Dcache : 0x00000000 - 0912BD81
    DataLo_Dcache: 0x00000001 - 2368110C, DataHi_Dcache : 0x00000000 - 0000001C
    TEXT_START : 0x21003178
    DATA_START : 0x260888A0
    Cause 0000040C (Code 0x3): TLB (store) exception
    Writing crashinfo to flash:crashinfo_20101028-220211-UTC
    22:02:11 UTC Thu Oct 28 2010: TLB (store) exception, CPU signal 10, PC = 0x22768478

    --------------------------------------------------------------------
    Possible software fault. Upon reccurence, please collect
    crashinfo, "show tech" and contact Cisco Technical Support.
    --------------------------------------------------------------------

    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z
    $0 : 00000000 00000000, AT : 00000000 29130000, v0 : 00000000 00000001, v1 : 00000000 0D8B8540
    a0 : 00000000 00000000, a1 : 00000000 0D8B8584, a2 : 00000000 2A2F8ABC, a3 : 00000000 00000004
    t0 : 00000000 00000020, t1 : 00000000 500099E1, t2 : 00000000 500081E0, t3 : FFFFFFFF FFFFFFF2
    t4 : 00000000 0000000E, t5 : 00000000 00000000, t6 : 00000000 0D95F890, t7 : 00000000 000001FF
    s0 : 00000000 00000000, s1 : 00000000 2A2FDB40, s2 : FFFFFFFF FFFFFFEC, s3 : 00000000 3080C980
    s4 : 00000000 0D95F89E, s5 : 00000000 2A300EE0, s6 : 00000000 00000000, s7 : 00000000 0000000E
    t8 : 00000000 000007FC, t9 : 00000000 2A300200, k0 : 00000000 00000000, k1 : 00000000 00000000
    gp : 00000000 29133C00, sp : 00000000 3022FBB8, s8 : 00000000 00000054, ra : 00000000 22768424
    EPC : 22768478, ErrorEPC : 80412AB4, SREG : 500099E3
    MDLO : 87126668, MDHI : D990ADBB, BadVaddr : 00000014
    CacheErr_Icache : 0x007F7F00 - 000040D8, CacheErr_Dcache : 0x00000000 - 00001FA0
    TagLo_Icache : 0x00000000 - 23642303, DataLo_Icache : 0xAFBF0018 - 0D81ADDB
    DataHi_Icache: 0x00000000 - 00000001
    TagLo_Dcache : 0x00000000 - 2277E583, TagHi_Dcache : 0x00000000 - 0912BD81
    DataLo_Dcache: 0x00000001 - 2368110C, DataHi_Dcache : 0x00000000 - 0000001C
    TEXT_START : 0x21003178
    DATA_START : 0x260888A0
    Cause 0000040C (Code 0x3): TLB (store) exception
    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z

    === Flushing messages (22:02:12 UTC Thu Oct 28 2010) ===
    Buffered messages:
    *Oct 28 20:52:40.075: %LINK-3-UPDOWN: Interface SM1/0, changed state to up
    *Oct 28 20:52:42.195: %LINK-3-UPDOWN: Interface GigabitEthernet0/0, changed state to up
    *Oct 28 20:52:42.195: %LINK-3-UPDOWN: Interface GigabitEthernet0/1, changed state to down
    *Oct 28 20:52:42.195: %LINK-3-UPDOWN: Interface GigabitEthernet0/2, changed state to down
    *Oct 28 20:52:44.631: %LINK-3-UPDOWN: Interface SM1/1, changed state to up
    *Oct 28 20:53:01.655: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/0, changed state to up
    *Oct 28 20:53:01.923: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/1, changed state to up
    *Oct 28 20:53:02.075: %LINK-3-UPDOWN: Interface Foreign Exchange Station 0/1/0, changed state to up
    *Oct 28 20:53:02.075: %LINK-3-UPDOWN: Interface Foreign Exchange Station 0/1/1, changed state to up
    *Oct 28 20:53:43.739: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/0, changed state to operational status down due to cable removal
    *Oct 28 20:53:44.739: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/1, changed state to operational status down due to cable removal
    Queued messages:
    No warm reboot Storage
    *** System received a Bus Error exception ***
    signal= 0xa, code= 0x40c, context= 0x29726b74
    PC = 0x22768478, SP = 0x3022fbb8, RA = 0x22768424
    Cause Reg = 0x0000040c, Status Reg = 0x500099e3
    System Bootstrap, Version 15.0(1r)M6, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 2010 by cisco Systems, Inc.
    Total memory size = 512 MB - On-board = 512 MB, DIMM0 = 0 MB
    CISCO2911/K9 platform with 524288 Kbytes of main memory
    Main memory is configured to 72/-1(On-board/DIMM0) bit mode with ECC enabled

    Readonly ROMMON initialized
    program load complete, entry point: 0x80803000, size: 0x1b340

    IOS Image Load Test
    ___________________
    Digitally Signed Development Software
    program load complete, entry point: 0x81000000, size: 0x40b6b74
    Self decompressing the image : #############################################################################################################

    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2691036>
    or simply reply to this email.
    -- --
    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2691978>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2699015>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2699042>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2699089>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2699640>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2704890>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2703353>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2708817>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2712882>
    or simply reply to this email.
    -- --
    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2713045>
    or simply reply to this email.
    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2713062>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2713416>
    or simply reply to this email.


    Subject: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-
    Replied by: Radhika Miriyala on 20-11-2010 01:34:39 AM
    Ken,

    They are still looking into it. I will keep you posted on any new information.  Can you continue with trying out SRE-v with out the PVDM in your setup?



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Friday, November 05, 2010 9:26 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    Any new status today on new IOS?

    Thanks in advance,

    Ken


    Thanks Ken. The information you have below is good enough.



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Thursday, November 04, 2010 2:26 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Radhika Miriyala in Service Ready Engine Virtualizatio



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    I have it running with debug on and not sure what I am supposed to be looking for.
    Here is the command you asked me to run:

    boxer#sh voice dsp group slot 0
    dsp 1:
    State: UP, firmware: 27.2.0
    Max signal/voice channel: 16/16
    Max credits: 240
    num_of_sig_chnls_allocated: 4
    Transcoding channels allocated: 0
    Group: FLEX_GROUP_VOICE, complexity: FLEX
    Shared credits: 240, reserved credits: 0
    Signaling channels allocated: 4
    Voice channels allocated: 0
    Credits used (rounded-up): 0
    Slot: 0
    Device idx: 0
    PVDM Slot: 0
    Dsp Type: SP2600


    Ken,

    Can you try the following to make sure the PVDM is working as expected.


    A) sh voice dsp group slot 0
    dsp 1:
    State: UP, firmware: 28.0.126 <<<< (out put would be something like this)
    ...

    <http://mce_host/html/js/editor/@theme_images_path@/emoticons/cool.gif> debug vpm dsp

    Thanks,

    Radhika





    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Thursday, November 04, 2010 11:12 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Radhika Miriyala in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Radhika Miriyala has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Ken,

    I think what you did is fine but I will check with IOs team to confirm if they want any additional tests.



    Appreciate your trying all the tests for us.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Thursday, November 04, 2010 11:00 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    The router seemed to work with the PVDM before configuring the sre-v, is there a particular test they would like me to try?

    Ken



    Ken,

    Yes the IOS team was able to reproduce it. They are working on fixing the issue. Also one quick question the IOS team wanted to know was if the have used the PVDM successfully before the using sre-v.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Thursday, November 04, 2010 9:45 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    Do you know if the IOS team has been able to reproduce this yet?

    Thanks in advance,

    Ken Romo


    Ken,

    The IOS team is trying to reproduce this in their setup. I will let you know what the finding are or if we need a debug session with you (if they can¿t reproduce in their setup)



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Wednesday, November 03, 2010 9:03 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    Anything new here today?

    Thanks again,

    Ken



    Ken,

    Right now it looks an IOS bug but we need to reproduce this in house so we can confirm for sure. I will keep you in the loop on what we find. If it turns out to be an issue with this particular PVDM I will let you know.



    Appreciate all your help with this.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Tuesday, November 02, 2010 9:51 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    So what is the root cause?

    The IOS or the PVDMS?

    Do I need to RMA my PVDMS?

    Let me know thank you.

    Ken


    Ken,

    Thanks for the information. We will check internally if this has been tested. I will cancel the debug session for today since we most likely have the root cause for the issue. We will try to reproduce this internally and if we need further information from you will setup a different session.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Tuesday, November 02, 2010 8:49 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    The PVDMS is:

    PVDM3-16 V01
    S/N FOC14200FNK

    Is this what you were looking for?

    Ken


    Ken,

    I am not sure if it is the PVDM that is bad but it could be a bug in the IOS image also where you have pvdm and the SRE module it could be some issue. For now can you continute to do beta for SRE-v without the PVDMS.



    I will check with the team and get back to you as to how to proceed.



    Can you let me know what PVDM models you have so we can try to reproduce this in our lab.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Monday, November 01, 2010 3:59 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    I pulled the PVDM and it is working.

    Does this mean the PVDM is bad?

    Ken


    Ken,

    Please try out the new image sent by Brett to you when you get a chance. Also one difference we noticed is that you have PVDM¿s in your setup that we don not have in our test setup. Would it be possible to remove the PVDMS temporarily and try the ping? This may help us root cause the issue.



    I will also schedule a WebEx for tomorrow morning 10:30 PST with the IOS developer so we can take a look if the change of IOS image and removal of PVDM¿s does not solve the issue. Please let me know if that time slot does not work for you.



    Thanks,

    Radhika





    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Monday, November 01, 2010 11:19 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    Here you go:

    boxer#show vlan-switch
    VLAN Name Status Ports
    ---- -------------------------------- --------- -------------------------------
    1 default active
    1002 fddi-default act/unsup
    1003 token-ring-default act/unsup
    1004 fddinet-default act/unsup
    1005 trnet-default act/unsup
    VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2
    ---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------
    1 enet 100001 1500 - - - - - 1002 1003
    1002 fddi 101002 1500 - - - - - 1 1003
    1003 tr 101003 1500 1005 0 - - srb 1 1002
    1004 fdnet 101004 1500 - - 1 ibm - 0 0
    1005 trnet 101005 1500 - - 1 ibm - 0 0


    boxer#sh platform mgf module
    Registered Module Information
    Code: NR - Not Registered, TM - Trust Mode, SP - Scheduling Profile
    BL - Buffer Level, TR - Traffic Rate, PT - Pause Threshold
    slot vlan type/ID TM SP BL TR PT
    ---- ---- ---------- ------- --- ------ ----- ----
    ISM NR
    EHWIC-0 NR
    EHWIC-1 NR
    EHWIC-2 NR
    EHWIC-3 NR
    PVDM-0 2 PVDM/5 UP 1 low 1000 low
    PVDM-1 2 PVDM/5 UP 1 low 1000 low
    SM-1 1 Switch/3 UP 1 low 1000 high




    Thanks Ken. Can you also give us the output of the following.



    1) show vlan-switch

    2) ¿show platform mgf module¿ before the crash happens.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Monday, November 01, 2010 10:50 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    I will try whatever you suggest, just let me know when you have posted the new IOS.

    Below is my config:

    boxer#sh run
    Building configuration...

    Current configuration : 5777 bytes
    !
    version 15.1
    service timestamps debug datetime msec
    service timestamps log datetime msec
    no service password-encryption
    !
    hostname boxer
    !
    boot-start-marker
    boot system flash0 c2900-universalk9-mz.SSA.151-2.19.T
    boot-end-marker
    !
    !
    logging buffered 51200 warnings
    !
    no aaa new-model
    !
    no ipv6 cef
    ip source-route
    ip cef
    !
    !
    !
    !
    !
    ip domain name yourdomain.com
    multilink bundle-name authenticated
    !
    !
    !
    !
    !
    crypto pki token default removal timeout 0
    !
    crypto pki trustpoint TP-self-signed-1999750280
    enrollment selfsigned
    subject-name cn=IOS-Self-Signed-Certificate-1999750280
    revocation-check none
    rsakeypair TP-self-signed-1999750280
    !
    !
    crypto pki certificate chain TP-self-signed-1999750280
    certificate self-signed 01
    3082024C 308201B5 A0030201 02020101 300D0609 2A864886 F70D0101 04050030
    31312F30 2D060355 04031326 494F532D 53656C66 2D536967 6E65642D 43657274
    69666963 6174652D 31393939 37353032 3830301E 170D3130 31303230 32323335
    32365A17 0D323030 31303130 30303030 305A3031 312F302D 06035504 03132649
    4F532D53 656C662D 5369676E 65642D43 65727469 66696361 74652D31 39393937
    35303238 3030819F 300D0609 2A864886 F70D0101 01050003 818D0030 81890281
    81009378 2E139D79 DCA59865 14AB3398 870362B7 40BB9C13 A5DC5315 6108DF92
    5E78CF06 A40D4DB5 B66D410E FAFE75AC 764997B1 5C551A47 CFA00109 520352EC
    33A69E24 B3C1175B 136FC62A 8BE4637E B834059B FC7CAA6E 957DA0BB 66D8DC49
    80F82890 981FFCFE 0DC7E6F9 53287989 3887C5F6 AF59D0BE B502E11E FD16F556
    DBB90203 010001A3 74307230 0F060355 1D130101 FF040530 030101FF 301F0603
    551D1104 18301682 14626F78 65722E79 6F757264 6F6D6169 6E2E636F 6D301F06
    03551D23 04183016 80143541 7934E424 4B9A60DB E6C908C3 C20BAA17 D058301D
    0603551D 0E041604 14354179 34E4244B 9A60DBE6 C908C3C2 0BAA17D0 58300D06
    092A8648 86F70D01 01040500 03818100 3D222AB5 177D452F 153DCA26 1D7ECB49
    58BCBF60 DA18DC04 94B82EA3 76884EBC D7131641 08687C04 6C6645DF 78B2D2F8
    409BCAD7 50AF5091 B99614FD C2424D89 407A9109 BCA20473 F4CE33D4 4B126483
    C240C0B9 7A628E53 E419FEC3 B8853671 03113F5E 47FA8120 9F9A7A9D 11498FE0
    82C96578 8FD9770A EBD27F73 DF2E1487
    quit
    voice-card 0
    !
    !
    !
    !
    !
    !
    !
    license udi pid CISCO2911/K9 sn FTX1422A077
    hw-module pvdm 0/0
    !
    hw-module sm 1
    !
    !
    !
    username jack privilege 15 secret 5 $1$c5QR$fYGTbhWRKsBZ1JpNyIQGG1
    username marco privilege 15 secret 5 $1$amqq$5pI0T7mUViDL5Y.NqX/yz.
    !
    redundancy
    !
    !
    !
    !
    !
    !
    interface GigabitEthernet0/0
    description To tusqa network
    ip address 172.17.17.130 255.255.248.0
    duplex auto
    speed auto
    !
    interface GigabitEthernet0/1
    no ip address
    shutdown
    duplex auto
    speed auto
    !
    interface GigabitEthernet0/2
    no ip address
    shutdown
    duplex auto
    speed auto
    !
    interface SM1/0
    ip unnumbered GigabitEthernet0/0
    service-module ip address 172.17.17.129 255.255.248.0
    !Application: SRE-V Running on SMV
    service-module ip default-gateway 172.17.17.130
    service-module mgf ip address 10.62.64.1 255.255.255.0
    service-module mgf ip default-gateway 10.62.64.2
    !
    interface SM1/1
    description Internal switch interface connected to Service Module
    switchport mode trunk
    !
    interface Vlan1
    ip address 10.62.64.2 255.255.255.0
    !
    ip forward-protocol nd
    !
    ip http server
    ip http access-class 23
    ip http authentication local
    ip http secure-server
    ip http timeout-policy idle 60 life 86400 requests 10000
    !
    ip route 172.17.17.129 255.255.255.255 SM1/0
    !
    !
    !
    !
    control-plane
    !
    !
    voice-port 0/0/0
    !
    voice-port 0/0/1
    !
    voice-port 0/1/0
    !
    voice-port 0/1/1
    !
    !
    !
    mgcp profile default
    !
    !
    !
    !
    !
    gatekeeper
    shutdown
    !
    !
    banner exec ^C
    % Password expiration warning.
    -----------------------------------------------------------------------
    Cisco Configuration Professional (Cisco CP) is installed on this device
    and it provides the default username "cisco" for one-time use. If you have
    already used the username "cisco" to login to the router and your IOS image
    supports the "one-time" user option, then this username has already expired.
    You will not be able to login to the router with this username after you exit
    this session.
    It is strongly suggested that you create a new username with a privilege level
    of 15 using the following command.
    username <myuser> privilege 15 secret 0 <mypassword>
    Replace <myuser> and <mypassword> with the username and password you want to
    use.
    -----------------------------------------------------------------------
    ^C
    banner login ^C
    -----------------------------------------------------------------------
    Cisco Configuration Professional (Cisco CP) is installed on this device.
    This feature requires the one-time use of the username "cisco" with the
    password "cisco". These default credentials have a privilege level of 15.
    YOU MUST USE CISCO CP or the CISCO IOS CLI TO CHANGE THESE PUBLICLY-KNOWN
    CREDENTIALS
    Here are the Cisco IOS commands.
    username <myuser> privilege 15 secret 0 <mypassword>
    no username cisco
    Replace <myuser> and <mypassword> with the username and password you want
    to use.
    IF YOU DO NOT CHANGE THE PUBLICLY-KNOWN CREDENTIALS, YOU WILL NOT BE ABLE
    TO LOG INTO THE DEVICE AGAIN AFTER YOU HAVE LOGGED OFF.
    For more information about Cisco CP please follow the instructions in the
    QUICK START GUIDE for your router or go to http://www.cisco.com/go/ciscocp
    -----------------------------------------------------------------------
    ^C
    !
    line con 0
    login local
    line aux 0
    line 67
    no activation-character
    no exec
    transport preferred none
    transport input all
    transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
    stopbits 1
    flowcontrol software
    line vty 0 4
    privilege level 15
    login local
    transport input telnet
    line vty 5 15
    privilege level 15
    login local
    transport input telnet ssh
    !
    exception data-corruption buffer truncate
    scheduler allocate 20000 1000
    end



    Ken, Thanks for trying out the image for us. We are trying to reproduce this on our end but have had no luck so far. Can you please send us the output of show running-config from your router.



    Also we have one more image that we would like you to try it out before the debusg session would that be ok?



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Monday, November 01, 2010 10:22 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------

    Radhika,

    I tried the new OS and still getting same IOS crash.
    As mentioned I will work around your schedule so let me if you were able to get someone from the IOS team to help troubleshoot today.

    Thanks in advance,

    Ken Romo


    Ken,

    I am trying to get some help from the IOS team since this a router crash. So I will setup the webex session to debug for some time Monday so we can collect all the information and try out any suggestion from them.



    For Now We will post a newer IOS image to the beta Site and can you give that a try to see if that will solve the issue.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Friday, October 29, 2010 8:24 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    I will work around your schedule, anytime you are available, I will make myself available.
    email:
    kromo@opentext.com

    Thanks in advance,

    Ken Romo

    +++++++++++++++++++++++++++++++++

    Ken,

    Would a webex session tomorrow morning (any time between 10:00 and 1:00) work for you? Let me know the time that would work for you and also your email address so I can send you a webex invite.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Thursday, October 28, 2010 3:12 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Radhika Miriyala in Service Ready Engine Virtualizatio



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    No worries, we are trying to work this out together and I appreciate the help.
    s/m 1/1 is set as trunk but I went ahead and reconfigured to truank again and reloaded OS and get the same crash when I ping to the MGF interface from the SRE (I attached the errors at the bottom of this message).

    Ken,

    Sorry I just realized the mistake. I meant to say make the interface sm 1/1 as trunk.

    Sorry about the confusion.



    Please try it out.



    Thanks,

    Radhika



    boxer#
    %ALIGN-1-FATAL: Illegal access to a low address 22:02:10 UTC Thu Oct 28 2010
    addr=0x14, pc=0x22765BD8z , ra=0x22765B84z , sp=0x3022FBB8
    %ALIGN-1-FATAL: Illegal access to a low address 22:02:11 UTC Thu Oct 28 2010
    addr=0x14, pc=0x22765BD8z , ra=0x22765B84z , sp=0x3022FBB8

    22:02:11 UTC Thu Oct 28 2010: TLB (store) exception, CPU signal 10, PC = 0x22768478

    --------------------------------------------------------------------
    Possible software fault. Upon reccurence, please collect
    crashinfo, "show tech" and contact Cisco Technical Support.
    --------------------------------------------------------------------

    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z
    $0 : 00000000 00000000, AT : 00000000 29130000, v0 : 00000000 00000001, v1 : 00000000 0D8B8540
    a0 : 00000000 00000000, a1 : 00000000 0D8B8584, a2 : 00000000 2A2F8ABC, a3 : 00000000 00000004
    t0 : 00000000 00000020, t1 : 00000000 500099E1, t2 : 00000000 500081E0, t3 : FFFFFFFF FFFFFFF2
    t4 : 00000000 0000000E, t5 : 00000000 00000000, t6 : 00000000 0D95F890, t7 : 00000000 000001FF
    s0 : 00000000 00000000, s1 : 00000000 2A2FDB40, s2 : FFFFFFFF FFFFFFEC, s3 : 00000000 3080C980
    s4 : 00000000 0D95F89E, s5 : 00000000 2A300EE0, s6 : 00000000 00000000, s7 : 00000000 0000000E
    t8 : 00000000 000007FC, t9 : 00000000 2A300200, k0 : 00000000 00000000, k1 : 00000000 00000000
    gp : 00000000 29133C00, sp : 00000000 3022FBB8, s8 : 00000000 00000054, ra : 00000000 22768424
    EPC : 22768478, ErrorEPC : 80412AB4, SREG : 500099E3
    MDLO : 87126668, MDHI : D990ADBB, BadVaddr : 00000014
    CacheErr_Icache : 0x007F7F00 - 000040D8, CacheErr_Dcache : 0x00000000 - 00001FA0
    TagLo_Icache : 0x00000000 - 23642303, DataLo_Icache : 0xAFBF0018 - 0D81ADDB
    DataHi_Icache: 0x00000000 - 00000001
    TagLo_Dcache : 0x00000000 - 2277E583, TagHi_Dcache : 0x00000000 - 0912BD81
    DataLo_Dcache: 0x00000001 - 2368110C, DataHi_Dcache : 0x00000000 - 0000001C
    TEXT_START : 0x21003178
    DATA_START : 0x260888A0
    Cause 0000040C (Code 0x3): TLB (store) exception

    22:02:11 UTC Thu Oct 28 2010: TLB (store) exception, CPU signal 10, PC = 0x22768478

    --------------------------------------------------------------------
    Possible software fault. Upon reccurence, please collect
    crashinfo, "show tech" and contact Cisco Technical Support.
    --------------------------------------------------------------------

    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z
    $0 : 00000000 00000000, AT : 00000000 29130000, v0 : 00000000 00000001, v1 : 00000000 0D8B8540
    a0 : 00000000 00000000, a1 : 00000000 0D8B8584, a2 : 00000000 2A2F8ABC, a3 : 00000000 00000004
    t0 : 00000000 00000020, t1 : 00000000 500099E1, t2 : 00000000 500081E0, t3 : FFFFFFFF FFFFFFF2
    t4 : 00000000 0000000E, t5 : 00000000 00000000, t6 : 00000000 0D95F890, t7 : 00000000 000001FF
    s0 : 00000000 00000000, s1 : 00000000 2A2FDB40, s2 : FFFFFFFF FFFFFFEC, s3 : 00000000 3080C980
    s4 : 00000000 0D95F89E, s5 : 00000000 2A300EE0, s6 : 00000000 00000000, s7 : 00000000 0000000E
    t8 : 00000000 000007FC, t9 : 00000000 2A300200, k0 : 00000000 00000000, k1 : 00000000 00000000
    gp : 00000000 29133C00, sp : 00000000 3022FBB8, s8 : 00000000 00000054, ra : 00000000 22768424
    EPC : 22768478, ErrorEPC : 80412AB4, SREG : 500099E3
    MDLO : 87126668, MDHI : D990ADBB, BadVaddr : 00000014
    CacheErr_Icache : 0x007F7F00 - 000040D8, CacheErr_Dcache : 0x00000000 - 00001FA0
    TagLo_Icache : 0x00000000 - 23642303, DataLo_Icache : 0xAFBF0018 - 0D81ADDB
    DataHi_Icache: 0x00000000 - 00000001
    TagLo_Dcache : 0x00000000 - 2277E583, TagHi_Dcache : 0x00000000 - 0912BD81
    DataLo_Dcache: 0x00000001 - 2368110C, DataHi_Dcache : 0x00000000 - 0000001C
    TEXT_START : 0x21003178
    DATA_START : 0x260888A0
    Cause 0000040C (Code 0x3): TLB (store) exception
    Writing crashinfo to flash:crashinfo_20101028-220211-UTC
    22:02:11 UTC Thu Oct 28 2010: TLB (store) exception, CPU signal 10, PC = 0x22768478

    --------------------------------------------------------------------
    Possible software fault. Upon reccurence, please collect
    crashinfo, "show tech" and contact Cisco Technical Support.
    --------------------------------------------------------------------

    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z
    $0 : 00000000 00000000, AT : 00000000 29130000, v0 : 00000000 00000001, v1 : 00000000 0D8B8540
    a0 : 00000000 00000000, a1 : 00000000 0D8B8584, a2 : 00000000 2A2F8ABC, a3 : 00000000 00000004
    t0 : 00000000 00000020, t1 : 00000000 500099E1, t2 : 00000000 500081E0, t3 : FFFFFFFF FFFFFFF2
    t4 : 00000000 0000000E, t5 : 00000000 00000000, t6 : 00000000 0D95F890, t7 : 00000000 000001FF
    s0 : 00000000 00000000, s1 : 00000000 2A2FDB40, s2 : FFFFFFFF FFFFFFEC, s3 : 00000000 3080C980
    s4 : 00000000 0D95F89E, s5 : 00000000 2A300EE0, s6 : 00000000 00000000, s7 : 00000000 0000000E
    t8 : 00000000 000007FC, t9 : 00000000 2A300200, k0 : 00000000 00000000, k1 : 00000000 00000000
    gp : 00000000 29133C00, sp : 00000000 3022FBB8, s8 : 00000000 00000054, ra : 00000000 22768424
    EPC : 22768478, ErrorEPC : 80412AB4, SREG : 500099E3
    MDLO : 87126668, MDHI : D990ADBB, BadVaddr : 00000014
    CacheErr_Icache : 0x007F7F00 - 000040D8, CacheErr_Dcache : 0x00000000 - 00001FA0
    TagLo_Icache : 0x00000000 - 23642303, DataLo_Icache : 0xAFBF0018 - 0D81ADDB
    DataHi_Icache: 0x00000000 - 00000001
    TagLo_Dcache : 0x00000000 - 2277E583, TagHi_Dcache : 0x00000000 - 0912BD81
    DataLo_Dcache: 0x00000001 - 2368110C, DataHi_Dcache : 0x00000000 - 0000001C
    TEXT_START : 0x21003178
    DATA_START : 0x260888A0
    Cause 0000040C (Code 0x3): TLB (store) exception
    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z

    === Flushing messages (22:02:12 UTC Thu Oct 28 2010) ===
    Buffered messages:
    *Oct 28 20:52:40.075: %LINK-3-UPDOWN: Interface SM1/0, changed state to up
    *Oct 28 20:52:42.195: %LINK-3-UPDOWN: Interface GigabitEthernet0/0, changed state to up
    *Oct 28 20:52:42.195: %LINK-3-UPDOWN: Interface GigabitEthernet0/1, changed state to down
    *Oct 28 20:52:42.195: %LINK-3-UPDOWN: Interface GigabitEthernet0/2, changed state to down
    *Oct 28 20:52:44.631: %LINK-3-UPDOWN: Interface SM1/1, changed state to up
    *Oct 28 20:53:01.655: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/0, changed state to up
    *Oct 28 20:53:01.923: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/1, changed state to up
    *Oct 28 20:53:02.075: %LINK-3-UPDOWN: Interface Foreign Exchange Station 0/1/0, changed state to up
    *Oct 28 20:53:02.075: %LINK-3-UPDOWN: Interface Foreign Exchange Station 0/1/1, changed state to up
    *Oct 28 20:53:43.739: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/0, changed state to operational status down due to cable removal
    *Oct 28 20:53:44.739: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/1, changed state to operational status down due to cable removal
    Queued messages:
    No warm reboot Storage
    *** System received a Bus Error exception ***
    signal= 0xa, code= 0x40c, context= 0x29726b74
    PC = 0x22768478, SP = 0x3022fbb8, RA = 0x22768424
    Cause Reg = 0x0000040c, Status Reg = 0x500099e3
    System Bootstrap, Version 15.0(1r)M6, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 2010 by cisco Systems, Inc.
    Total memory size = 512 MB - On-board = 512 MB, DIMM0 = 0 MB
    CISCO2911/K9 platform with 524288 Kbytes of main memory
    Main memory is configured to 72/-1(On-board/DIMM0) bit mode with ECC enabled

    Readonly ROMMON initialized
    program load complete, entry point: 0x80803000, size: 0x1b340

    IOS Image Load Test
    ___________________
    Digitally Signed Development Software
    program load complete, entry point: 0x81000000, size: 0x40b6b74
    Self decompressing the image : #############################################################################################################

    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2691036>
    or simply reply to this email.
    -- --
    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2691978>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2699015>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2699042>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2699089>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2699640>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2704890>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2703353>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2708817>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2712882>
    or simply reply to this email.
    -- --
    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2713045>
    or simply reply to this email.
    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2713062>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2713416>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2716531>
    or simply reply to this email.

    Subject: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-
    Replied by: Ken Romo on 20-11-2010 01:34:39 AM
    Radhika,
     
    I have my application running on a virtual machine on the sre-v but  I need to use the FXO and FXS ports on the router to complete my testing and those ports will not start without the PVDM.

    Ken
     
    Ken,

    They are still looking into it. I will keep you posted on any new information. Can you continue with trying out SRE-v with out the PVDM in your setup?



    Thanks,

    Radhika

    Subject: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-
    Replied by: Radhika Miriyala on 20-11-2010 01:34:39 AM
    Ok Ken thanks for updating us. We will try to get a fix as soon as we can.



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Friday, November 05, 2010 9:57 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    I have my application running on a virtual machine on the sre-v but  I need to use the FXO and FXS ports on the router to complete my testing and those ports will not start without the PVDM.

    Ken

    Ken,

    They are still looking into it. I will keep you posted on any new information. Can you continue with trying out SRE-v with out the PVDM in your setup?



    Thanks,

    Radhika
    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2716602>
    or simply reply to this email.

    Subject: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-
    Replied by: Ken Romo on 20-11-2010 01:34:39 AM
    Radhika,
     
    As you mentioned I am continuing testing on the SRE-V until you get a fix for the IOS. I have installed and configured our application in a VM on the SRE however I am having trouble accessing an external network from the VM (running Windows 2003 server).
    I would like to access the 172.17.17.0 255.255.255.248 from my VM. Below are the settings from my VM and ISR/SRE, do I need to add a route on the ISR for this to happen?
     
     
    VM (I can ping the GigEth 0/0 from my VM)
     
    IP address ¿ 10.62.64.10
    Subnet ¿ 255.255.255.0
    Gateway 10.62.64.2
     
    ISR
     
    interface GigabitEthernet0/0
     
     ip address 172.17.17.130 255.255.248.0
     duplex auto
     speed auto
     
    interface SM1/0
     ip unnumbered GigabitEthernet0/0
     service-module ip address 172.17.17.129 255.255.248.0
     !Application: SRE-V Running on SMV
     service-module ip default-gateway 172.17.17.130
     service-module mgf ip address 10.62.64.1 255.255.255.0
     service-module mgf ip default-gateway 10.62.64.2
    !
    interface SM1/1
     description Internal switch interface connected to Service Module
     switchport mode trunk
    !
    interface Vlan1
     ip address 10.62.64.2 255.255.255.0
    !
    !
    ip route 172.17.17.129 255.255.255.255 SM1/0

     
    Ken,

    They are still looking into it. I will keep you posted on any new information. Can you continue with trying out SRE-v with out the PVDM in your setup?



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Friday, November 05, 2010 9:26 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    Any new status today on new IOS?

    Thanks in advance,

    Ken


    Thanks Ken. The information you have below is good enough.



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Thursday, November 04, 2010 2:26 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Radhika Miriyala in Service Ready Engine Virtualizatio



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    I have it running with debug on and not sure what I am supposed to be looking for.
    Here is the command you asked me to run:

    boxer#sh voice dsp group slot 0
    dsp 1:
    State: UP, firmware: 27.2.0
    Max signal/voice channel: 16/16
    Max credits: 240
    num_of_sig_chnls_allocated: 4
    Transcoding channels allocated: 0
    Group: FLEX_GROUP_VOICE, complexity: FLEX
    Shared credits: 240, reserved credits: 0
    Signaling channels allocated: 4
    Voice channels allocated: 0
    Credits used (rounded-up): 0
    Slot: 0
    Device idx: 0
    PVDM Slot: 0
    Dsp Type: SP2600


    Ken,

    Can you try the following to make sure the PVDM is working as expected.


    A) sh voice dsp group slot 0
    dsp 1:
    State: UP, firmware: 28.0.126 <<<< (out put would be something like this)
    ...

    <http://mce_host/html/js/editor/@theme_images_path@/emoticons/cool.gif> debug vpm dsp

    Thanks,

    Radhika





    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Thursday, November 04, 2010 11:12 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Radhika Miriyala in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Radhika Miriyala has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Ken,

    I think what you did is fine but I will check with IOs team to confirm if they want any additional tests.



    Appreciate your trying all the tests for us.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Thursday, November 04, 2010 11:00 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    The router seemed to work with the PVDM before configuring the sre-v, is there a particular test they would like me to try?

    Ken



    Ken,

    Yes the IOS team was able to reproduce it. They are working on fixing the issue. Also one quick question the IOS team wanted to know was if the have used the PVDM successfully before the using sre-v.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Thursday, November 04, 2010 9:45 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    Do you know if the IOS team has been able to reproduce this yet?

    Thanks in advance,

    Ken Romo


    Ken,

    The IOS team is trying to reproduce this in their setup. I will let you know what the finding are or if we need a debug session with you (if they can¿t reproduce in their setup)



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Wednesday, November 03, 2010 9:03 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    Anything new here today?

    Thanks again,

    Ken



    Ken,

    Right now it looks an IOS bug but we need to reproduce this in house so we can confirm for sure. I will keep you in the loop on what we find. If it turns out to be an issue with this particular PVDM I will let you know.



    Appreciate all your help with this.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Tuesday, November 02, 2010 9:51 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    So what is the root cause?

    The IOS or the PVDMS?

    Do I need to RMA my PVDMS?

    Let me know thank you.

    Ken


    Ken,

    Thanks for the information. We will check internally if this has been tested. I will cancel the debug session for today since we most likely have the root cause for the issue. We will try to reproduce this internally and if we need further information from you will setup a different session.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Tuesday, November 02, 2010 8:49 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    The PVDMS is:

    PVDM3-16 V01
    S/N FOC14200FNK

    Is this what you were looking for?

    Ken


    Ken,

    I am not sure if it is the PVDM that is bad but it could be a bug in the IOS image also where you have pvdm and the SRE module it could be some issue. For now can you continute to do beta for SRE-v without the PVDMS.



    I will check with the team and get back to you as to how to proceed.



    Can you let me know what PVDM models you have so we can try to reproduce this in our lab.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Monday, November 01, 2010 3:59 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    I pulled the PVDM and it is working.

    Does this mean the PVDM is bad?

    Ken


    Ken,

    Please try out the new image sent by Brett to you when you get a chance. Also one difference we noticed is that you have PVDM¿s in your setup that we don not have in our test setup. Would it be possible to remove the PVDMS temporarily and try the ping? This may help us root cause the issue.



    I will also schedule a WebEx for tomorrow morning 10:30 PST with the IOS developer so we can take a look if the change of IOS image and removal of PVDM¿s does not solve the issue. Please let me know if that time slot does not work for you.



    Thanks,

    Radhika





    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Monday, November 01, 2010 11:19 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    Here you go:

    boxer#show vlan-switch
    VLAN Name Status Ports
    ---- -------------------------------- --------- -------------------------------
    1 default active
    1002 fddi-default act/unsup
    1003 token-ring-default act/unsup
    1004 fddinet-default act/unsup
    1005 trnet-default act/unsup
    VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2
    ---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------
    1 enet 100001 1500 - - - - - 1002 1003
    1002 fddi 101002 1500 - - - - - 1 1003
    1003 tr 101003 1500 1005 0 - - srb 1 1002
    1004 fdnet 101004 1500 - - 1 ibm - 0 0
    1005 trnet 101005 1500 - - 1 ibm - 0 0


    boxer#sh platform mgf module
    Registered Module Information
    Code: NR - Not Registered, TM - Trust Mode, SP - Scheduling Profile
    BL - Buffer Level, TR - Traffic Rate, PT - Pause Threshold
    slot vlan type/ID TM SP BL TR PT
    ---- ---- ---------- ------- --- ------ ----- ----
    ISM NR
    EHWIC-0 NR
    EHWIC-1 NR
    EHWIC-2 NR
    EHWIC-3 NR
    PVDM-0 2 PVDM/5 UP 1 low 1000 low
    PVDM-1 2 PVDM/5 UP 1 low 1000 low
    SM-1 1 Switch/3 UP 1 low 1000 high




    Thanks Ken. Can you also give us the output of the following.



    1) show vlan-switch

    2) ¿show platform mgf module¿ before the crash happens.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Monday, November 01, 2010 10:50 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    I will try whatever you suggest, just let me know when you have posted the new IOS.

    Below is my config:

    boxer#sh run
    Building configuration...

    Current configuration : 5777 bytes
    !
    version 15.1
    service timestamps debug datetime msec
    service timestamps log datetime msec
    no service password-encryption
    !
    hostname boxer
    !
    boot-start-marker
    boot system flash0 c2900-universalk9-mz.SSA.151-2.19.T
    boot-end-marker
    !
    !
    logging buffered 51200 warnings
    !
    no aaa new-model
    !
    no ipv6 cef
    ip source-route
    ip cef
    !
    !
    !
    !
    !
    ip domain name yourdomain.com
    multilink bundle-name authenticated
    !
    !
    !
    !
    !
    crypto pki token default removal timeout 0
    !
    crypto pki trustpoint TP-self-signed-1999750280
    enrollment selfsigned
    subject-name cn=IOS-Self-Signed-Certificate-1999750280
    revocation-check none
    rsakeypair TP-self-signed-1999750280
    !
    !
    crypto pki certificate chain TP-self-signed-1999750280
    certificate self-signed 01
    3082024C 308201B5 A0030201 02020101 300D0609 2A864886 F70D0101 04050030
    31312F30 2D060355 04031326 494F532D 53656C66 2D536967 6E65642D 43657274
    69666963 6174652D 31393939 37353032 3830301E 170D3130 31303230 32323335
    32365A17 0D323030 31303130 30303030 305A3031 312F302D 06035504 03132649
    4F532D53 656C662D 5369676E 65642D43 65727469 66696361 74652D31 39393937
    35303238 3030819F 300D0609 2A864886 F70D0101 01050003 818D0030 81890281
    81009378 2E139D79 DCA59865 14AB3398 870362B7 40BB9C13 A5DC5315 6108DF92
    5E78CF06 A40D4DB5 B66D410E FAFE75AC 764997B1 5C551A47 CFA00109 520352EC
    33A69E24 B3C1175B 136FC62A 8BE4637E B834059B FC7CAA6E 957DA0BB 66D8DC49
    80F82890 981FFCFE 0DC7E6F9 53287989 3887C5F6 AF59D0BE B502E11E FD16F556
    DBB90203 010001A3 74307230 0F060355 1D130101 FF040530 030101FF 301F0603
    551D1104 18301682 14626F78 65722E79 6F757264 6F6D6169 6E2E636F 6D301F06
    03551D23 04183016 80143541 7934E424 4B9A60DB E6C908C3 C20BAA17 D058301D
    0603551D 0E041604 14354179 34E4244B 9A60DBE6 C908C3C2 0BAA17D0 58300D06
    092A8648 86F70D01 01040500 03818100 3D222AB5 177D452F 153DCA26 1D7ECB49
    58BCBF60 DA18DC04 94B82EA3 76884EBC D7131641 08687C04 6C6645DF 78B2D2F8
    409BCAD7 50AF5091 B99614FD C2424D89 407A9109 BCA20473 F4CE33D4 4B126483
    C240C0B9 7A628E53 E419FEC3 B8853671 03113F5E 47FA8120 9F9A7A9D 11498FE0
    82C96578 8FD9770A EBD27F73 DF2E1487
    quit
    voice-card 0
    !
    !
    !
    !
    !
    !
    !
    license udi pid CISCO2911/K9 sn FTX1422A077
    hw-module pvdm 0/0
    !
    hw-module sm 1
    !
    !
    !
    username jack privilege 15 secret 5 $1$c5QR$fYGTbhWRKsBZ1JpNyIQGG1
    username marco privilege 15 secret 5 $1$amqq$5pI0T7mUViDL5Y.NqX/yz.
    !
    redundancy
    !
    !
    !
    !
    !
    !
    interface GigabitEthernet0/0
    description To tusqa network
    ip address 172.17.17.130 255.255.248.0
    duplex auto
    speed auto
    !
    interface GigabitEthernet0/1
    no ip address
    shutdown
    duplex auto
    speed auto
    !
    interface GigabitEthernet0/2
    no ip address
    shutdown
    duplex auto
    speed auto
    !
    interface SM1/0
    ip unnumbered GigabitEthernet0/0
    service-module ip address 172.17.17.129 255.255.248.0
    !Application: SRE-V Running on SMV
    service-module ip default-gateway 172.17.17.130
    service-module mgf ip address 10.62.64.1 255.255.255.0
    service-module mgf ip default-gateway 10.62.64.2
    !
    interface SM1/1
    description Internal switch interface connected to Service Module
    switchport mode trunk
    !
    interface Vlan1
    ip address 10.62.64.2 255.255.255.0
    !
    ip forward-protocol nd
    !
    ip http server
    ip http access-class 23
    ip http authentication local
    ip http secure-server
    ip http timeout-policy idle 60 life 86400 requests 10000
    !
    ip route 172.17.17.129 255.255.255.255 SM1/0
    !
    !
    !
    !
    control-plane
    !
    !
    voice-port 0/0/0
    !
    voice-port 0/0/1
    !
    voice-port 0/1/0
    !
    voice-port 0/1/1
    !
    !
    !
    mgcp profile default
    !
    !
    !
    !
    !
    gatekeeper
    shutdown
    !
    !
    banner exec ^C
    % Password expiration warning.
    -----------------------------------------------------------------------
    Cisco Configuration Professional (Cisco CP) is installed on this device
    and it provides the default username "cisco" for one-time use. If you have
    already used the username "cisco" to login to the router and your IOS image
    supports the "one-time" user option, then this username has already expired.
    You will not be able to login to the router with this username after you exit
    this session.
    It is strongly suggested that you create a new username with a privilege level
    of 15 using the following command.
    username <myuser> privilege 15 secret 0 <mypassword>
    Replace <myuser> and <mypassword> with the username and password you want to
    use.
    -----------------------------------------------------------------------
    ^C
    banner login ^C
    -----------------------------------------------------------------------
    Cisco Configuration Professional (Cisco CP) is installed on this device.
    This feature requires the one-time use of the username "cisco" with the
    password "cisco". These default credentials have a privilege level of 15.
    YOU MUST USE CISCO CP or the CISCO IOS CLI TO CHANGE THESE PUBLICLY-KNOWN
    CREDENTIALS
    Here are the Cisco IOS commands.
    username <myuser> privilege 15 secret 0 <mypassword>
    no username cisco
    Replace <myuser> and <mypassword> with the username and password you want
    to use.
    IF YOU DO NOT CHANGE THE PUBLICLY-KNOWN CREDENTIALS, YOU WILL NOT BE ABLE
    TO LOG INTO THE DEVICE AGAIN AFTER YOU HAVE LOGGED OFF.
    For more information about Cisco CP please follow the instructions in the
    QUICK START GUIDE for your router or go to http://www.cisco.com/go/ciscocp
    -----------------------------------------------------------------------
    ^C
    !
    line con 0
    login local
    line aux 0
    line 67
    no activation-character
    no exec
    transport preferred none
    transport input all
    transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
    stopbits 1
    flowcontrol software
    line vty 0 4
    privilege level 15
    login local
    transport input telnet
    line vty 5 15
    privilege level 15
    login local
    transport input telnet ssh
    !
    exception data-corruption buffer truncate
    scheduler allocate 20000 1000
    end



    Ken, Thanks for trying out the image for us. We are trying to reproduce this on our end but have had no luck so far. Can you please send us the output of show running-config from your router.



    Also we have one more image that we would like you to try it out before the debusg session would that be ok?



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Monday, November 01, 2010 10:22 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------

    Radhika,

    I tried the new OS and still getting same IOS crash.
    As mentioned I will work around your schedule so let me if you were able to get someone from the IOS team to help troubleshoot today.

    Thanks in advance,

    Ken Romo


    Ken,

    I am trying to get some help from the IOS team since this a router crash. So I will setup the webex session to debug for some time Monday so we can collect all the information and try out any suggestion from them.



    For Now We will post a newer IOS image to the beta Site and can you give that a try to see if that will solve the issue.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Friday, October 29, 2010 8:24 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    I will work around your schedule, anytime you are available, I will make myself available.
    email:
    kromo@opentext.com

    Thanks in advance,

    Ken Romo

    +++++++++++++++++++++++++++++++++

    Ken,

    Would a webex session tomorrow morning (any time between 10:00 and 1:00) work for you? Let me know the time that would work for you and also your email address so I can send you a webex invite.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Thursday, October 28, 2010 3:12 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Radhika Miriyala in Service Ready Engine Virtualizatio



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    No worries, we are trying to work this out together and I appreciate the help.
    s/m 1/1 is set as trunk but I went ahead and reconfigured to truank again and reloaded OS and get the same crash when I ping to the MGF interface from the SRE (I attached the errors at the bottom of this message).

    Ken,

    Sorry I just realized the mistake. I meant to say make the interface sm 1/1 as trunk.

    Sorry about the confusion.



    Please try it out.



    Thanks,

    Radhika



    boxer#
    %ALIGN-1-FATAL: Illegal access to a low address 22:02:10 UTC Thu Oct 28 2010
    addr=0x14, pc=0x22765BD8z , ra=0x22765B84z , sp=0x3022FBB8
    %ALIGN-1-FATAL: Illegal access to a low address 22:02:11 UTC Thu Oct 28 2010
    addr=0x14, pc=0x22765BD8z , ra=0x22765B84z , sp=0x3022FBB8

    22:02:11 UTC Thu Oct 28 2010: TLB (store) exception, CPU signal 10, PC = 0x22768478

    --------------------------------------------------------------------
    Possible software fault. Upon reccurence, please collect
    crashinfo, "show tech" and contact Cisco Technical Support.
    --------------------------------------------------------------------

    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z
    $0 : 00000000 00000000, AT : 00000000 29130000, v0 : 00000000 00000001, v1 : 00000000 0D8B8540
    a0 : 00000000 00000000, a1 : 00000000 0D8B8584, a2 : 00000000 2A2F8ABC, a3 : 00000000 00000004
    t0 : 00000000 00000020, t1 : 00000000 500099E1, t2 : 00000000 500081E0, t3 : FFFFFFFF FFFFFFF2
    t4 : 00000000 0000000E, t5 : 00000000 00000000, t6 : 00000000 0D95F890, t7 : 00000000 000001FF
    s0 : 00000000 00000000, s1 : 00000000 2A2FDB40, s2 : FFFFFFFF FFFFFFEC, s3 : 00000000 3080C980
    s4 : 00000000 0D95F89E, s5 : 00000000 2A300EE0, s6 : 00000000 00000000, s7 : 00000000 0000000E
    t8 : 00000000 000007FC, t9 : 00000000 2A300200, k0 : 00000000 00000000, k1 : 00000000 00000000
    gp : 00000000 29133C00, sp : 00000000 3022FBB8, s8 : 00000000 00000054, ra : 00000000 22768424
    EPC : 22768478, ErrorEPC : 80412AB4, SREG : 500099E3
    MDLO : 87126668, MDHI : D990ADBB, BadVaddr : 00000014
    CacheErr_Icache : 0x007F7F00 - 000040D8, CacheErr_Dcache : 0x00000000 - 00001FA0
    TagLo_Icache : 0x00000000 - 23642303, DataLo_Icache : 0xAFBF0018 - 0D81ADDB
    DataHi_Icache: 0x00000000 - 00000001
    TagLo_Dcache : 0x00000000 - 2277E583, TagHi_Dcache : 0x00000000 - 0912BD81
    DataLo_Dcache: 0x00000001 - 2368110C, DataHi_Dcache : 0x00000000 - 0000001C
    TEXT_START : 0x21003178
    DATA_START : 0x260888A0
    Cause 0000040C (Code 0x3): TLB (store) exception

    22:02:11 UTC Thu Oct 28 2010: TLB (store) exception, CPU signal 10, PC = 0x22768478

    --------------------------------------------------------------------
    Possible software fault. Upon reccurence, please collect
    crashinfo, "show tech" and contact Cisco Technical Support.
    --------------------------------------------------------------------

    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z
    $0 : 00000000 00000000, AT : 00000000 29130000, v0 : 00000000 00000001, v1 : 00000000 0D8B8540
    a0 : 00000000 00000000, a1 : 00000000 0D8B8584, a2 : 00000000 2A2F8ABC, a3 : 00000000 00000004
    t0 : 00000000 00000020, t1 : 00000000 500099E1, t2 : 00000000 500081E0, t3 : FFFFFFFF FFFFFFF2
    t4 : 00000000 0000000E, t5 : 00000000 00000000, t6 : 00000000 0D95F890, t7 : 00000000 000001FF
    s0 : 00000000 00000000, s1 : 00000000 2A2FDB40, s2 : FFFFFFFF FFFFFFEC, s3 : 00000000 3080C980
    s4 : 00000000 0D95F89E, s5 : 00000000 2A300EE0, s6 : 00000000 00000000, s7 : 00000000 0000000E
    t8 : 00000000 000007FC, t9 : 00000000 2A300200, k0 : 00000000 00000000, k1 : 00000000 00000000
    gp : 00000000 29133C00, sp : 00000000 3022FBB8, s8 : 00000000 00000054, ra : 00000000 22768424
    EPC : 22768478, ErrorEPC : 80412AB4, SREG : 500099E3
    MDLO : 87126668, MDHI : D990ADBB, BadVaddr : 00000014
    CacheErr_Icache : 0x007F7F00 - 000040D8, CacheErr_Dcache : 0x00000000 - 00001FA0
    TagLo_Icache : 0x00000000 - 23642303, DataLo_Icache : 0xAFBF0018 - 0D81ADDB
    DataHi_Icache: 0x00000000 - 00000001
    TagLo_Dcache : 0x00000000 - 2277E583, TagHi_Dcache : 0x00000000 - 0912BD81
    DataLo_Dcache: 0x00000001 - 2368110C, DataHi_Dcache : 0x00000000 - 0000001C
    TEXT_START : 0x21003178
    DATA_START : 0x260888A0
    Cause 0000040C (Code 0x3): TLB (store) exception
    Writing crashinfo to flash:crashinfo_20101028-220211-UTC
    22:02:11 UTC Thu Oct 28 2010: TLB (store) exception, CPU signal 10, PC = 0x22768478

    --------------------------------------------------------------------
    Possible software fault. Upon reccurence, please collect
    crashinfo, "show tech" and contact Cisco Technical Support.
    --------------------------------------------------------------------

    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z
    $0 : 00000000 00000000, AT : 00000000 29130000, v0 : 00000000 00000001, v1 : 00000000 0D8B8540
    a0 : 00000000 00000000, a1 : 00000000 0D8B8584, a2 : 00000000 2A2F8ABC, a3 : 00000000 00000004
    t0 : 00000000 00000020, t1 : 00000000 500099E1, t2 : 00000000 500081E0, t3 : FFFFFFFF FFFFFFF2
    t4 : 00000000 0000000E, t5 : 00000000 00000000, t6 : 00000000 0D95F890, t7 : 00000000 000001FF
    s0 : 00000000 00000000, s1 : 00000000 2A2FDB40, s2 : FFFFFFFF FFFFFFEC, s3 : 00000000 3080C980
    s4 : 00000000 0D95F89E, s5 : 00000000 2A300EE0, s6 : 00000000 00000000, s7 : 00000000 0000000E
    t8 : 00000000 000007FC, t9 : 00000000 2A300200, k0 : 00000000 00000000, k1 : 00000000 00000000
    gp : 00000000 29133C00, sp : 00000000 3022FBB8, s8 : 00000000 00000054, ra : 00000000 22768424
    EPC : 22768478, ErrorEPC : 80412AB4, SREG : 500099E3
    MDLO : 87126668, MDHI : D990ADBB, BadVaddr : 00000014
    CacheErr_Icache : 0x007F7F00 - 000040D8, CacheErr_Dcache : 0x00000000 - 00001FA0
    TagLo_Icache : 0x00000000 - 23642303, DataLo_Icache : 0xAFBF0018 - 0D81ADDB
    DataHi_Icache: 0x00000000 - 00000001
    TagLo_Dcache : 0x00000000 - 2277E583, TagHi_Dcache : 0x00000000 - 0912BD81
    DataLo_Dcache: 0x00000001 - 2368110C, DataHi_Dcache : 0x00000000 - 0000001C
    TEXT_START : 0x21003178
    DATA_START : 0x260888A0
    Cause 0000040C (Code 0x3): TLB (store) exception
    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z

    === Flushing messages (22:02:12 UTC Thu Oct 28 2010) ===
    Buffered messages:
    *Oct 28 20:52:40.075: %LINK-3-UPDOWN: Interface SM1/0, changed state to up
    *Oct 28 20:52:42.195: %LINK-3-UPDOWN: Interface GigabitEthernet0/0, changed state to up
    *Oct 28 20:52:42.195: %LINK-3-UPDOWN: Interface GigabitEthernet0/1, changed state to down
    *Oct 28 20:52:42.195: %LINK-3-UPDOWN: Interface GigabitEthernet0/2, changed state to down
    *Oct 28 20:52:44.631: %LINK-3-UPDOWN: Interface SM1/1, changed state to up
    *Oct 28 20:53:01.655: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/0, changed state to up
    *Oct 28 20:53:01.923: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/1, changed state to up
    *Oct 28 20:53:02.075: %LINK-3-UPDOWN: Interface Foreign Exchange Station 0/1/0, changed state to up
    *Oct 28 20:53:02.075: %LINK-3-UPDOWN: Interface Foreign Exchange Station 0/1/1, changed state to up
    *Oct 28 20:53:43.739: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/0, changed state to operational status down due to cable removal
    *Oct 28 20:53:44.739: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/1, changed state to operational status down due to cable removal
    Queued messages:
    No warm reboot Storage
    *** System received a Bus Error exception ***
    signal= 0xa, code= 0x40c, context= 0x29726b74
    PC = 0x22768478, SP = 0x3022fbb8, RA = 0x22768424
    Cause Reg = 0x0000040c, Status Reg = 0x500099e3
    System Bootstrap, Version 15.0(1r)M6, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 2010 by cisco Systems, Inc.
    Total memory size = 512 MB - On-board = 512 MB, DIMM0 = 0 MB
    CISCO2911/K9 platform with 524288 Kbytes of main memory
    Main memory is configured to 72/-1(On-board/DIMM0) bit mode with ECC enabled

    Readonly ROMMON initialized
    program load complete, entry point: 0x80803000, size: 0x1b340

    IOS Image Load Test
    ___________________
    Digitally Signed Development Software
    program load complete, entry point: 0x81000000, size: 0x40b6b74
    Self decompressing the image : #############################################################################################################

    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2691036>
    or simply reply to this email.
    -- --
    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2691978>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2699015>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2699042>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2699089>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2699640>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2704890>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2703353>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2708817>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2712882>
    or simply reply to this email.
    -- --
    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2713045>
    or simply reply to this email.
    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2713062>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2713416>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2716531>
    or simply reply to this email.


    Subject: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-
    Replied by: Radhika Miriyala on 20-11-2010 01:34:39 AM
    Ken,

    Are you trying to ping  some particular system in your network? What is the default gateway for that system? The issue you are having most like is the the Vlan 1 network is private to the this particular ISR and your other systems/switches are not aware of this Vlan1.



    So what I would do is add a route for this 10.62.64.0 network to point to your gige 0/0 on the ISR.



    Please try that out and let me know if you still have issues.



    Thanks,

    Radhika





    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Thursday, November 11, 2010 8:38 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    As you mentioned I am continuing testing on the SRE-V until you get a fix for the IOS. I have installed and configured our application in a VM on the SRE however I am having trouble accessing an external network from the VM (running Windows 2003 server).
    I would like to access the 172.17.17.0 255.255.255.248 from my VM. Below are the settings from my VM and ISR/SRE, do I need to add a route on the ISR for this to happen?


    VM (I can ping the GigEth 0/0 from my VM)

    IP address ¿ 10.62.64.10
    Subnet ¿ 255.255.255.0
    Gateway 10.62.64.2

    ISR

    interface GigabitEthernet0/0

    ip address 172.17.17.130 255.255.248.0
    duplex auto
    speed auto

    interface SM1/0
    ip unnumbered GigabitEthernet0/0
    service-module ip address 172.17.17.129 255.255.248.0
    !Application: SRE-V Running on SMV
    service-module ip default-gateway 172.17.17.130
    service-module mgf ip address 10.62.64.1 255.255.255.0
    service-module mgf ip default-gateway 10.62.64.2
    !
    interface SM1/1
    description Internal switch interface connected to Service Module
    switchport mode trunk
    !
    interface Vlan1
    ip address 10.62.64.2 255.255.255.0
    !
    !
    ip route 172.17.17.129 255.255.255.255 SM1/0



    Ken,

    They are still looking into it. I will keep you posted on any new information. Can you continue with trying out SRE-v with out the PVDM in your setup?



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Friday, November 05, 2010 9:26 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    Any new status today on new IOS?

    Thanks in advance,

    Ken


    Thanks Ken. The information you have below is good enough.



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Thursday, November 04, 2010 2:26 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Radhika Miriyala in Service Ready Engine Virtualizatio



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    I have it running with debug on and not sure what I am supposed to be looking for.
    Here is the command you asked me to run:

    boxer#sh voice dsp group slot 0
    dsp 1:
    State: UP, firmware: 27.2.0
    Max signal/voice channel: 16/16
    Max credits: 240
    num_of_sig_chnls_allocated: 4
    Transcoding channels allocated: 0
    Group: FLEX_GROUP_VOICE, complexity: FLEX
    Shared credits: 240, reserved credits: 0
    Signaling channels allocated: 4
    Voice channels allocated: 0
    Credits used (rounded-up): 0
    Slot: 0
    Device idx: 0
    PVDM Slot: 0
    Dsp Type: SP2600


    Ken,

    Can you try the following to make sure the PVDM is working as expected.


    A) sh voice dsp group slot 0
    dsp 1:
    State: UP, firmware: 28.0.126 <<<< (out put would be something like this)
    ...

    <http://mce_host/html/js/editor/@theme_images_path@/emoticons/cool.gif> debug vpm dsp

    Thanks,

    Radhika





    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Thursday, November 04, 2010 11:12 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Radhika Miriyala in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Radhika Miriyala has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Ken,

    I think what you did is fine but I will check with IOs team to confirm if they want any additional tests.



    Appreciate your trying all the tests for us.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Thursday, November 04, 2010 11:00 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    The router seemed to work with the PVDM before configuring the sre-v, is there a particular test they would like me to try?

    Ken



    Ken,

    Yes the IOS team was able to reproduce it. They are working on fixing the issue. Also one quick question the IOS team wanted to know was if the have used the PVDM successfully before the using sre-v.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Thursday, November 04, 2010 9:45 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    Do you know if the IOS team has been able to reproduce this yet?

    Thanks in advance,

    Ken Romo


    Ken,

    The IOS team is trying to reproduce this in their setup. I will let you know what the finding are or if we need a debug session with you (if they can¿t reproduce in their setup)



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Wednesday, November 03, 2010 9:03 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    Anything new here today?

    Thanks again,

    Ken



    Ken,

    Right now it looks an IOS bug but we need to reproduce this in house so we can confirm for sure. I will keep you in the loop on what we find. If it turns out to be an issue with this particular PVDM I will let you know.



    Appreciate all your help with this.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Tuesday, November 02, 2010 9:51 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    So what is the root cause?

    The IOS or the PVDMS?

    Do I need to RMA my PVDMS?

    Let me know thank you.

    Ken


    Ken,

    Thanks for the information. We will check internally if this has been tested. I will cancel the debug session for today since we most likely have the root cause for the issue. We will try to reproduce this internally and if we need further information from you will setup a different session.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Tuesday, November 02, 2010 8:49 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    The PVDMS is:

    PVDM3-16 V01
    S/N FOC14200FNK

    Is this what you were looking for?

    Ken


    Ken,

    I am not sure if it is the PVDM that is bad but it could be a bug in the IOS image also where you have pvdm and the SRE module it could be some issue. For now can you continute to do beta for SRE-v without the PVDMS.



    I will check with the team and get back to you as to how to proceed.



    Can you let me know what PVDM models you have so we can try to reproduce this in our lab.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Monday, November 01, 2010 3:59 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    I pulled the PVDM and it is working.

    Does this mean the PVDM is bad?

    Ken


    Ken,

    Please try out the new image sent by Brett to you when you get a chance. Also one difference we noticed is that you have PVDM¿s in your setup that we don not have in our test setup. Would it be possible to remove the PVDMS temporarily and try the ping? This may help us root cause the issue.



    I will also schedule a WebEx for tomorrow morning 10:30 PST with the IOS developer so we can take a look if the change of IOS image and removal of PVDM¿s does not solve the issue. Please let me know if that time slot does not work for you.



    Thanks,

    Radhika





    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Monday, November 01, 2010 11:19 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    Here you go:

    boxer#show vlan-switch
    VLAN Name Status Ports
    ---- -------------------------------- --------- -------------------------------
    1 default active
    1002 fddi-default act/unsup
    1003 token-ring-default act/unsup
    1004 fddinet-default act/unsup
    1005 trnet-default act/unsup
    VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2
    ---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------
    1 enet 100001 1500 - - - - - 1002 1003
    1002 fddi 101002 1500 - - - - - 1 1003
    1003 tr 101003 1500 1005 0 - - srb 1 1002
    1004 fdnet 101004 1500 - - 1 ibm - 0 0
    1005 trnet 101005 1500 - - 1 ibm - 0 0


    boxer#sh platform mgf module
    Registered Module Information
    Code: NR - Not Registered, TM - Trust Mode, SP - Scheduling Profile
    BL - Buffer Level, TR - Traffic Rate, PT - Pause Threshold
    slot vlan type/ID TM SP BL TR PT
    ---- ---- ---------- ------- --- ------ ----- ----
    ISM NR
    EHWIC-0 NR
    EHWIC-1 NR
    EHWIC-2 NR
    EHWIC-3 NR
    PVDM-0 2 PVDM/5 UP 1 low 1000 low
    PVDM-1 2 PVDM/5 UP 1 low 1000 low
    SM-1 1 Switch/3 UP 1 low 1000 high




    Thanks Ken. Can you also give us the output of the following.



    1) show vlan-switch

    2) ¿show platform mgf module¿ before the crash happens.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Monday, November 01, 2010 10:50 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    I will try whatever you suggest, just let me know when you have posted the new IOS.

    Below is my config:

    boxer#sh run
    Building configuration...

    Current configuration : 5777 bytes
    !
    version 15.1
    service timestamps debug datetime msec
    service timestamps log datetime msec
    no service password-encryption
    !
    hostname boxer
    !
    boot-start-marker
    boot system flash0 c2900-universalk9-mz.SSA.151-2.19.T
    boot-end-marker
    !
    !
    logging buffered 51200 warnings
    !
    no aaa new-model
    !
    no ipv6 cef
    ip source-route
    ip cef
    !
    !
    !
    !
    !
    ip domain name yourdomain.com
    multilink bundle-name authenticated
    !
    !
    !
    !
    !
    crypto pki token default removal timeout 0
    !
    crypto pki trustpoint TP-self-signed-1999750280
    enrollment selfsigned
    subject-name cn=IOS-Self-Signed-Certificate-1999750280
    revocation-check none
    rsakeypair TP-self-signed-1999750280
    !
    !
    crypto pki certificate chain TP-self-signed-1999750280
    certificate self-signed 01
    3082024C 308201B5 A0030201 02020101 300D0609 2A864886 F70D0101 04050030
    31312F30 2D060355 04031326 494F532D 53656C66 2D536967 6E65642D 43657274
    69666963 6174652D 31393939 37353032 3830301E 170D3130 31303230 32323335
    32365A17 0D323030 31303130 30303030 305A3031 312F302D 06035504 03132649
    4F532D53 656C662D 5369676E 65642D43 65727469 66696361 74652D31 39393937
    35303238 3030819F 300D0609 2A864886 F70D0101 01050003 818D0030 81890281
    81009378 2E139D79 DCA59865 14AB3398 870362B7 40BB9C13 A5DC5315 6108DF92
    5E78CF06 A40D4DB5 B66D410E FAFE75AC 764997B1 5C551A47 CFA00109 520352EC
    33A69E24 B3C1175B 136FC62A 8BE4637E B834059B FC7CAA6E 957DA0BB 66D8DC49
    80F82890 981FFCFE 0DC7E6F9 53287989 3887C5F6 AF59D0BE B502E11E FD16F556
    DBB90203 010001A3 74307230 0F060355 1D130101 FF040530 030101FF 301F0603
    551D1104 18301682 14626F78 65722E79 6F757264 6F6D6169 6E2E636F 6D301F06
    03551D23 04183016 80143541 7934E424 4B9A60DB E6C908C3 C20BAA17 D058301D
    0603551D 0E041604 14354179 34E4244B 9A60DBE6 C908C3C2 0BAA17D0 58300D06
    092A8648 86F70D01 01040500 03818100 3D222AB5 177D452F 153DCA26 1D7ECB49
    58BCBF60 DA18DC04 94B82EA3 76884EBC D7131641 08687C04 6C6645DF 78B2D2F8
    409BCAD7 50AF5091 B99614FD C2424D89 407A9109 BCA20473 F4CE33D4 4B126483
    C240C0B9 7A628E53 E419FEC3 B8853671 03113F5E 47FA8120 9F9A7A9D 11498FE0
    82C96578 8FD9770A EBD27F73 DF2E1487
    quit
    voice-card 0
    !
    !
    !
    !
    !
    !
    !
    license udi pid CISCO2911/K9 sn FTX1422A077
    hw-module pvdm 0/0
    !
    hw-module sm 1
    !
    !
    !
    username jack privilege 15 secret 5 $1$c5QR$fYGTbhWRKsBZ1JpNyIQGG1
    username marco privilege 15 secret 5 $1$amqq$5pI0T7mUViDL5Y.NqX/yz.
    !
    redundancy
    !
    !
    !
    !
    !
    !
    interface GigabitEthernet0/0
    description To tusqa network
    ip address 172.17.17.130 255.255.248.0
    duplex auto
    speed auto
    !
    interface GigabitEthernet0/1
    no ip address
    shutdown
    duplex auto
    speed auto
    !
    interface GigabitEthernet0/2
    no ip address
    shutdown
    duplex auto
    speed auto
    !
    interface SM1/0
    ip unnumbered GigabitEthernet0/0
    service-module ip address 172.17.17.129 255.255.248.0
    !Application: SRE-V Running on SMV
    service-module ip default-gateway 172.17.17.130
    service-module mgf ip address 10.62.64.1 255.255.255.0
    service-module mgf ip default-gateway 10.62.64.2
    !
    interface SM1/1
    description Internal switch interface connected to Service Module
    switchport mode trunk
    !
    interface Vlan1
    ip address 10.62.64.2 255.255.255.0
    !
    ip forward-protocol nd
    !
    ip http server
    ip http access-class 23
    ip http authentication local
    ip http secure-server
    ip http timeout-policy idle 60 life 86400 requests 10000
    !
    ip route 172.17.17.129 255.255.255.255 SM1/0
    !
    !
    !
    !
    control-plane
    !
    !
    voice-port 0/0/0
    !
    voice-port 0/0/1
    !
    voice-port 0/1/0
    !
    voice-port 0/1/1
    !
    !
    !
    mgcp profile default
    !
    !
    !
    !
    !
    gatekeeper
    shutdown
    !
    !
    banner exec ^C
    % Password expiration warning.
    -----------------------------------------------------------------------
    Cisco Configuration Professional (Cisco CP) is installed on this device
    and it provides the default username "cisco" for one-time use. If you have
    already used the username "cisco" to login to the router and your IOS image
    supports the "one-time" user option, then this username has already expired.
    You will not be able to login to the router with this username after you exit
    this session.
    It is strongly suggested that you create a new username with a privilege level
    of 15 using the following command.
    username <myuser> privilege 15 secret 0 <mypassword>
    Replace <myuser> and <mypassword> with the username and password you want to
    use.
    -----------------------------------------------------------------------
    ^C
    banner login ^C
    -----------------------------------------------------------------------
    Cisco Configuration Professional (Cisco CP) is installed on this device.
    This feature requires the one-time use of the username "cisco" with the
    password "cisco". These default credentials have a privilege level of 15.
    YOU MUST USE CISCO CP or the CISCO IOS CLI TO CHANGE THESE PUBLICLY-KNOWN
    CREDENTIALS
    Here are the Cisco IOS commands.
    username <myuser> privilege 15 secret 0 <mypassword>
    no username cisco
    Replace <myuser> and <mypassword> with the username and password you want
    to use.
    IF YOU DO NOT CHANGE THE PUBLICLY-KNOWN CREDENTIALS, YOU WILL NOT BE ABLE
    TO LOG INTO THE DEVICE AGAIN AFTER YOU HAVE LOGGED OFF.
    For more information about Cisco CP please follow the instructions in the
    QUICK START GUIDE for your router or go to http://www.cisco.com/go/ciscocp
    -----------------------------------------------------------------------
    ^C
    !
    line con 0
    login local
    line aux 0
    line 67
    no activation-character
    no exec
    transport preferred none
    transport input all
    transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
    stopbits 1
    flowcontrol software
    line vty 0 4
    privilege level 15
    login local
    transport input telnet
    line vty 5 15
    privilege level 15
    login local
    transport input telnet ssh
    !
    exception data-corruption buffer truncate
    scheduler allocate 20000 1000
    end



    Ken, Thanks for trying out the image for us. We are trying to reproduce this on our end but have had no luck so far. Can you please send us the output of show running-config from your router.



    Also we have one more image that we would like you to try it out before the debusg session would that be ok?



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Monday, November 01, 2010 10:22 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------

    Radhika,

    I tried the new OS and still getting same IOS crash.
    As mentioned I will work around your schedule so let me if you were able to get someone from the IOS team to help troubleshoot today.

    Thanks in advance,

    Ken Romo


    Ken,

    I am trying to get some help from the IOS team since this a router crash. So I will setup the webex session to debug for some time Monday so we can collect all the information and try out any suggestion from them.



    For Now We will post a newer IOS image to the beta Site and can you give that a try to see if that will solve the issue.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Friday, October 29, 2010 8:24 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    I will work around your schedule, anytime you are available, I will make myself available.
    email:
    kromo@opentext.com

    Thanks in advance,

    Ken Romo

    +++++++++++++++++++++++++++++++++

    Ken,

    Would a webex session tomorrow morning (any time between 10:00 and 1:00) work for you? Let me know the time that would work for you and also your email address so I can send you a webex invite.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Thursday, October 28, 2010 3:12 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Radhika Miriyala in Service Ready Engine Virtualizatio



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    No worries, we are trying to work this out together and I appreciate the help.
    s/m 1/1 is set as trunk but I went ahead and reconfigured to truank again and reloaded OS and get the same crash when I ping to the MGF interface from the SRE (I attached the errors at the bottom of this message).

    Ken,

    Sorry I just realized the mistake. I meant to say make the interface sm 1/1 as trunk.

    Sorry about the confusion.



    Please try it out.



    Thanks,

    Radhika



    boxer#
    %ALIGN-1-FATAL: Illegal access to a low address 22:02:10 UTC Thu Oct 28 2010
    addr=0x14, pc=0x22765BD8z , ra=0x22765B84z , sp=0x3022FBB8
    %ALIGN-1-FATAL: Illegal access to a low address 22:02:11 UTC Thu Oct 28 2010
    addr=0x14, pc=0x22765BD8z , ra=0x22765B84z , sp=0x3022FBB8

    22:02:11 UTC Thu Oct 28 2010: TLB (store) exception, CPU signal 10, PC = 0x22768478

    --------------------------------------------------------------------
    Possible software fault. Upon reccurence, please collect
    crashinfo, "show tech" and contact Cisco Technical Support.
    --------------------------------------------------------------------

    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z
    $0 : 00000000 00000000, AT : 00000000 29130000, v0 : 00000000 00000001, v1 : 00000000 0D8B8540
    a0 : 00000000 00000000, a1 : 00000000 0D8B8584, a2 : 00000000 2A2F8ABC, a3 : 00000000 00000004
    t0 : 00000000 00000020, t1 : 00000000 500099E1, t2 : 00000000 500081E0, t3 : FFFFFFFF FFFFFFF2
    t4 : 00000000 0000000E, t5 : 00000000 00000000, t6 : 00000000 0D95F890, t7 : 00000000 000001FF
    s0 : 00000000 00000000, s1 : 00000000 2A2FDB40, s2 : FFFFFFFF FFFFFFEC, s3 : 00000000 3080C980
    s4 : 00000000 0D95F89E, s5 : 00000000 2A300EE0, s6 : 00000000 00000000, s7 : 00000000 0000000E
    t8 : 00000000 000007FC, t9 : 00000000 2A300200, k0 : 00000000 00000000, k1 : 00000000 00000000
    gp : 00000000 29133C00, sp : 00000000 3022FBB8, s8 : 00000000 00000054, ra : 00000000 22768424
    EPC : 22768478, ErrorEPC : 80412AB4, SREG : 500099E3
    MDLO : 87126668, MDHI : D990ADBB, BadVaddr : 00000014
    CacheErr_Icache : 0x007F7F00 - 000040D8, CacheErr_Dcache : 0x00000000 - 00001FA0
    TagLo_Icache : 0x00000000 - 23642303, DataLo_Icache : 0xAFBF0018 - 0D81ADDB
    DataHi_Icache: 0x00000000 - 00000001
    TagLo_Dcache : 0x00000000 - 2277E583, TagHi_Dcache : 0x00000000 - 0912BD81
    DataLo_Dcache: 0x00000001 - 2368110C, DataHi_Dcache : 0x00000000 - 0000001C
    TEXT_START : 0x21003178
    DATA_START : 0x260888A0
    Cause 0000040C (Code 0x3): TLB (store) exception

    22:02:11 UTC Thu Oct 28 2010: TLB (store) exception, CPU signal 10, PC = 0x22768478

    --------------------------------------------------------------------
    Possible software fault. Upon reccurence, please collect
    crashinfo, "show tech" and contact Cisco Technical Support.
    --------------------------------------------------------------------

    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z
    $0 : 00000000 00000000, AT : 00000000 29130000, v0 : 00000000 00000001, v1 : 00000000 0D8B8540
    a0 : 00000000 00000000, a1 : 00000000 0D8B8584, a2 : 00000000 2A2F8ABC, a3 : 00000000 00000004
    t0 : 00000000 00000020, t1 : 00000000 500099E1, t2 : 00000000 500081E0, t3 : FFFFFFFF FFFFFFF2
    t4 : 00000000 0000000E, t5 : 00000000 00000000, t6 : 00000000 0D95F890, t7 : 00000000 000001FF
    s0 : 00000000 00000000, s1 : 00000000 2A2FDB40, s2 : FFFFFFFF FFFFFFEC, s3 : 00000000 3080C980
    s4 : 00000000 0D95F89E, s5 : 00000000 2A300EE0, s6 : 00000000 00000000, s7 : 00000000 0000000E
    t8 : 00000000 000007FC, t9 : 00000000 2A300200, k0 : 00000000 00000000, k1 : 00000000 00000000
    gp : 00000000 29133C00, sp : 00000000 3022FBB8, s8 : 00000000 00000054, ra : 00000000 22768424
    EPC : 22768478, ErrorEPC : 80412AB4, SREG : 500099E3
    MDLO : 87126668, MDHI : D990ADBB, BadVaddr : 00000014
    CacheErr_Icache : 0x007F7F00 - 000040D8, CacheErr_Dcache : 0x00000000 - 00001FA0
    TagLo_Icache : 0x00000000 - 23642303, DataLo_Icache : 0xAFBF0018 - 0D81ADDB
    DataHi_Icache: 0x00000000 - 00000001
    TagLo_Dcache : 0x00000000 - 2277E583, TagHi_Dcache : 0x00000000 - 0912BD81
    DataLo_Dcache: 0x00000001 - 2368110C, DataHi_Dcache : 0x00000000 - 0000001C
    TEXT_START : 0x21003178
    DATA_START : 0x260888A0
    Cause 0000040C (Code 0x3): TLB (store) exception
    Writing crashinfo to flash:crashinfo_20101028-220211-UTC
    22:02:11 UTC Thu Oct 28 2010: TLB (store) exception, CPU signal 10, PC = 0x22768478

    --------------------------------------------------------------------
    Possible software fault. Upon reccurence, please collect
    crashinfo, "show tech" and contact Cisco Technical Support.
    --------------------------------------------------------------------

    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z
    $0 : 00000000 00000000, AT : 00000000 29130000, v0 : 00000000 00000001, v1 : 00000000 0D8B8540
    a0 : 00000000 00000000, a1 : 00000000 0D8B8584, a2 : 00000000 2A2F8ABC, a3 : 00000000 00000004
    t0 : 00000000 00000020, t1 : 00000000 500099E1, t2 : 00000000 500081E0, t3 : FFFFFFFF FFFFFFF2
    t4 : 00000000 0000000E, t5 : 00000000 00000000, t6 : 00000000 0D95F890, t7 : 00000000 000001FF
    s0 : 00000000 00000000, s1 : 00000000 2A2FDB40, s2 : FFFFFFFF FFFFFFEC, s3 : 00000000 3080C980
    s4 : 00000000 0D95F89E, s5 : 00000000 2A300EE0, s6 : 00000000 00000000, s7 : 00000000 0000000E
    t8 : 00000000 000007FC, t9 : 00000000 2A300200, k0 : 00000000 00000000, k1 : 00000000 00000000
    gp : 00000000 29133C00, sp : 00000000 3022FBB8, s8 : 00000000 00000054, ra : 00000000 22768424
    EPC : 22768478, ErrorEPC : 80412AB4, SREG : 500099E3
    MDLO : 87126668, MDHI : D990ADBB, BadVaddr : 00000014
    CacheErr_Icache : 0x007F7F00 - 000040D8, CacheErr_Dcache : 0x00000000 - 00001FA0
    TagLo_Icache : 0x00000000 - 23642303, DataLo_Icache : 0xAFBF0018 - 0D81ADDB
    DataHi_Icache: 0x00000000 - 00000001
    TagLo_Dcache : 0x00000000 - 2277E583, TagHi_Dcache : 0x00000000 - 0912BD81
    DataLo_Dcache: 0x00000001 - 2368110C, DataHi_Dcache : 0x00000000 - 0000001C
    TEXT_START : 0x21003178
    DATA_START : 0x260888A0
    Cause 0000040C (Code 0x3): TLB (store) exception
    -Traceback= 0x22765BD8z 0x2277BD38z 0x216B1D3Cz 0x2161F25Cz 0x2117F618z 0x211810C4z 0x2115AFACz 0x21A6814Cz 0x22DC9A60z

    === Flushing messages (22:02:12 UTC Thu Oct 28 2010) ===
    Buffered messages:
    *Oct 28 20:52:40.075: %LINK-3-UPDOWN: Interface SM1/0, changed state to up
    *Oct 28 20:52:42.195: %LINK-3-UPDOWN: Interface GigabitEthernet0/0, changed state to up
    *Oct 28 20:52:42.195: %LINK-3-UPDOWN: Interface GigabitEthernet0/1, changed state to down
    *Oct 28 20:52:42.195: %LINK-3-UPDOWN: Interface GigabitEthernet0/2, changed state to down
    *Oct 28 20:52:44.631: %LINK-3-UPDOWN: Interface SM1/1, changed state to up
    *Oct 28 20:53:01.655: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/0, changed state to up
    *Oct 28 20:53:01.923: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/1, changed state to up
    *Oct 28 20:53:02.075: %LINK-3-UPDOWN: Interface Foreign Exchange Station 0/1/0, changed state to up
    *Oct 28 20:53:02.075: %LINK-3-UPDOWN: Interface Foreign Exchange Station 0/1/1, changed state to up
    *Oct 28 20:53:43.739: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/0, changed state to operational status down due to cable removal
    *Oct 28 20:53:44.739: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/1, changed state to operational status down due to cable removal
    Queued messages:
    No warm reboot Storage
    *** System received a Bus Error exception ***
    signal= 0xa, code= 0x40c, context= 0x29726b74
    PC = 0x22768478, SP = 0x3022fbb8, RA = 0x22768424
    Cause Reg = 0x0000040c, Status Reg = 0x500099e3
    System Bootstrap, Version 15.0(1r)M6, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 2010 by cisco Systems, Inc.
    Total memory size = 512 MB - On-board = 512 MB, DIMM0 = 0 MB
    CISCO2911/K9 platform with 524288 Kbytes of main memory
    Main memory is configured to 72/-1(On-board/DIMM0) bit mode with ECC enabled

    Readonly ROMMON initialized
    program load complete, entry point: 0x80803000, size: 0x1b340

    IOS Image Load Test
    ___________________
    Digitally Signed Development Software
    program load complete, entry point: 0x81000000, size: 0x40b6b74
    Self decompressing the image : #############################################################################################################

    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2691036>
    or simply reply to this email.
    -- --
    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2691978>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2699015>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2699042>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2699089>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2699640>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2704890>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2703353>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2708817>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2712882>
    or simply reply to this email.
    -- --
    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2713045>
    or simply reply to this email.
    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2713062>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2713416>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2716531>
    or simply reply to this email.


    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2734857>
    or simply reply to this email.

    Subject: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-
    Replied by: Ken Romo on 20-11-2010 01:34:40 AM
    Radhika,
     
    I added:
     
    ip route 10.62.64.0 255.255.255.255 GigabitEthernet0/0
     
    to the ISR and I still can't ping the 172.17.17.0 255.255.248.0 network
     
     
    Ken
     
    Ken,

    Are you trying to ping some particular system in your network? What is the default gateway for that system? The issue you are having most like is the the Vlan 1 network is private to the this particular ISR and your other systems/switches are not aware of this Vlan1.



    So what I would do is add a route for this 10.62.64.0 network to point to your gige 0/0 on the ISR.



    Please try that out and let me know if you still have issues.



    Thanks,

    Radhika





    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Thursday, November 11, 2010 8:38 AM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Ken Romo in Service Ready Engine Virtualization - SRE-



    Ken Romo has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,

    As you mentioned I am continuing testing on the SRE-V until you get a fix for the IOS. I have installed and configured our application in a VM on the SRE however I am having trouble accessing an external network from the VM (running Windows 2003 server).
    I would like to access the 172.17.17.0 255.255.255.248 from my VM. Below are the settings from my VM and ISR/SRE, do I need to add a route on the ISR for this to happen?


    VM (I can ping the GigEth 0/0 from my VM)

    IP address ¿ 10.62.64.10
    Subnet ¿ 255.255.255.0
    Gateway 10.62.64.2

    ISR

    interface GigabitEthernet0/0

    ip address 172.17.17.130 255.255.248.0
    duplex auto
    speed auto

    interface SM1/0
    ip unnumbered GigabitEthernet0/0
    service-module ip address 172.17.17.129 255.255.248.0
    !Application: SRE-V Running on SMV
    service-module ip default-gateway 172.17.17.130
    service-module mgf ip address 10.62.64.1 255.255.255.0
    service-module mgf ip default-gateway 10.62.64.2
    !
    interface SM1/1
    description Internal switch interface connected to Service Module
    switchport mode trunk
    !
    interface Vlan1
    ip address 10.62.64.2 255.255.255.0
    !
    !
    ip route 172.17.17.129 255.255.255.255 SM1/0



    Ken,

    They are still looking into it. I will keep you posted on any new information. Can you continue with trying out SRE-v with out the PVDM in your setup?



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Friday, November 05, 2010 9:26 AM
    To: cdicuser@developer.cisco.c