Multiple SREs in 3945

Version 1
    This document was generated from CDN thread

    Created by: Kevin Marraccini on 20-11-2010 01:34:15 AM
    I can't seem to be able to configure a 2nd SRE on the ISR.  I have ESX running on SM1/0-1.  When i try to configure SM3/0-1, i cannot get the Service-module ip address to work:
     
     
    ! <KDM> This SM works
    interface SM1/0 
     ip address 192.168.5.1 255.255.255.0
     service-module ip address 192.168.5.11 255.255.255.0
     !Application: SRE-V Running on SMV
     service-module ip default-gateway 192.168.5.1
     service-module mgf ip address 192.168.6.11 255.255.255.0
     service-module mgf ip default-gateway 192.168.6.1
    !
    interface SM1/1
     description Internal switch interface connected to Service Module
     switchport mode trunk
    !
    interface SM2/0
     no ip address
     shutdown
     service-module fail-open
    !
    interface SM2/1
     description Internal switch interface connected to Service Module
     shutdown
    !
    ! <KDM>  This one doesn't seem to want to work. 
    interface SM3/0
     ip address 192.168.8.1 255.255.255.0
     service-module ip address 192.168.8.11 255.255.255.0
     service-module ip default-gateway 192.168.8.1
     service-module mgf ip address 192.168.6.13 255.255.255.0
     service-module mgf ip default-gateway 192.168.6.1
    !
    interface SM3/1
     description Internal switch interface connected to Service Module
     switchport mode trunk
     
    Any issues loading up multiple SREs with this code? (or maybe i just missed something silly?)
    Thanks
    Kevin

    Subject: RE: New Message from Kevin Marraccini in Service Ready Engine Virtualizatio
    Replied by: Radhika Miriyala on 20-11-2010 01:34:16 AM
    Kevin,

    When you say you cannot get the service-module Ip address to be working what do you mean?

    1)      Where you able to install the image on sm 3/0?

    2)      If you were able to install than can you provide the output of ¿show hypervisor ip¿



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Wednesday, October 06, 2010 1:53 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Kevin Marraccini in Service Ready Engine Virtualization - SRE-V Beta Testing: Multiple SREs in 3945



    Kevin Marraccini has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    I can't seem to be able to configure a 2nd SRE on the ISR.  I have ESX running on SM1/0-1.  When i try to configure SM3/0-1, i cannot get the Service-module ip address to work:


    ! <KDM> This SM works
    interface SM1/0
    ip address 192.168.5.1 255.255.255.0
    service-module ip address 192.168.5.11 255.255.255.0
    !Application: SRE-V Running on SMV
    service-module ip default-gateway 192.168.5.1
    service-module mgf ip address 192.168.6.11 255.255.255.0
    service-module mgf ip default-gateway 192.168.6.1
    !
    interface SM1/1
    description Internal switch interface connected to Service Module
    switchport mode trunk
    !
    interface SM2/0
    no ip address
    shutdown
    service-module fail-open
    !
    interface SM2/1
    description Internal switch interface connected to Service Module
    shutdown
    !
    ! <KDM>  This one doesn't seem to want to work. 
    interface SM3/0
    ip address 192.168.8.1 255.255.255.0
    service-module ip address 192.168.8.11 255.255.255.0
    service-module ip default-gateway 192.168.8.1
    service-module mgf ip address 192.168.6.13 255.255.255.0
    service-module mgf ip default-gateway 192.168.6.1
    !
    interface SM3/1
    description Internal switch interface connected to Service Module
    switchport mode trunk

    Any issues loading up multiple SREs with this code? (or maybe i just missed something silly?)
    Thanks
    Kevin
    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2613259>
    or simply reply to this email.

    Subject: RE: New Message from Kevin Marraccini in Service Ready Engine Virtualizatio
    Replied by: Tony Anderson on 20-11-2010 01:34:16 AM
    I am running in to the same issue.
     
    interface SM1/0
     ip address 172.28.207.17 255.255.255.252
     service-module ip address 172.28.207.18 255.255.255.252
     !Application: SRE-V Running on SMV
     service-module ip default-gateway 172.28.207.17
     service-module mgf ip address 172.28.207.34 255.255.255.252
     service-module mgf ip default-gateway 172.28.207.33
    !
    interface SM1/1
     description Internal switch interface connected to Service Module
     switchport mode trunk
    !
    interface SM2/0
     ip address 172.28.207.21 255.255.255.252
     service-module ip address 172.28.207.22 255.255.255.252
     !Application: SRE-V Running on SMV
     service-module ip default-gateway 172.28.207.21
     service-module mgf ip address 172.28.207.38 255.255.255.252
     service-module mgf ip default-gateway 172.28.207.37
    !        
    interface SM2/1
     description Internal switch interface connected to Service Module
     switchport mode trunk
     
    se-172-28-207-18# sh hypervisor ip
    Hostname:               localhost
    Domain Name:            None
    IP Config:              172.28.207.34(Subnet Mask: 255.255.255.248)
                            169.254.1.1(Subnet Mask: 255.255.255.0)
    Default Gateway:        172.28.207.33
    Preferred DNS Server:   None
    Alternative DNS Server: None
     
    se-172-28-207-22# sh hypervisor ip
    Hostname:               localhost
    Domain Name:            None
    IP Config:              172.28.207.38(Subnet Mask: 255.255.255.252)
                            169.254.1.1(Subnet Mask: 255.255.255.0)
    Default Gateway:        172.28.207.37
    Preferred DNS Server:   None
    Alternative DNS Server: None

     
    Thanks,
    Tony

    Subject: RE: New Message from Kevin Marraccini in Service Ready Engine Virtualizatio
    Replied by: Tony Anderson on 20-11-2010 01:34:16 AM
    Maybe I misread this.  On my router the service module address works (I can ping the address configured in the router), but I can't ping the hypervisor address.

    Subject: RE: New Message from Tony Anderson in Service Ready Engine Virtualization -
    Replied by: Michael Kinzlmaier on 20-11-2010 01:34:16 AM
    Hi Tony,



    Have you enabled the evaluation license using the ¿license activate sreVHost¿ command ?



    Mike





    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Thursday, October 07, 2010 3:08 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Tony Anderson in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Kevin Marraccini in Service Ready Engine Virtualizatio



    Tony Anderson has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Maybe I misread this.  On my router the service module address works (I can ping the address configured in the router), but I can't ping the hypervisor address.
    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2617622>
    or simply reply to this email.

    Subject: RE: New Message from Tony Anderson in Service Ready Engine Virtualization -
    Replied by: Radhika Miriyala on 20-11-2010 01:34:16 AM
    Tony,

    1)      Can you please give your interface vlan1 config?

    2)      Can you ping the Hypervisor Ip from the router?

    3)      Output of show license in-use

    4)      Output of ¿show hypervisor nics¿ for sm 2/0



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Thursday, October 07, 2010 12:05 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Tony Anderson in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Kevin Marraccini in Service Ready Engine Virtualizatio



    Tony Anderson has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    I am running in to the same issue.

    interface SM1/0
    ip address 172.28.207.17 255.255.255.252
    service-module ip address 172.28.207.18 255.255.255.252
    !Application: SRE-V Running on SMV
    service-module ip default-gateway 172.28.207.17
    service-module mgf ip address 172.28.207.34 255.255.255.252
    service-module mgf ip default-gateway 172.28.207.33
    !
    interface SM1/1
    description Internal switch interface connected to Service Module
    switchport mode trunk
    !
    interface SM2/0
    ip address 172.28.207.21 255.255.255.252
    service-module ip address 172.28.207.22 255.255.255.252
    !Application: SRE-V Running on SMV
    service-module ip default-gateway 172.28.207.21
    service-module mgf ip address 172.28.207.38 255.255.255.252
    service-module mgf ip default-gateway 172.28.207.37
    !        
    interface SM2/1
    description Internal switch interface connected to Service Module
    switchport mode trunk

    se-172-28-207-18# sh hypervisor ip
    Hostname:               localhost
    Domain Name:            None
    IP Config:              172.28.207.34(Subnet Mask: 255.255.255.248)
                            169.254.1.1(Subnet Mask: 255.255.255.0)
    Default Gateway:        172.28.207.33
    Preferred DNS Server:   None
    Alternative DNS Server: None

    se-172-28-207-22# sh hypervisor ip
    Hostname:               localhost
    Domain Name:            None
    IP Config:              172.28.207.38(Subnet Mask: 255.255.255.252)
                            169.254.1.1(Subnet Mask: 255.255.255.0)
    Default Gateway:        172.28.207.37
    Preferred DNS Server:   None
    Alternative DNS Server: None


    Thanks,
    Tony
    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2617617>
    or simply reply to this email.

    Subject: RE: New Message from Radhika Miriyala in Service Ready Engine Virtualizatio
    Replied by: Tony Anderson on 20-11-2010 01:34:17 AM
    Hi Radhika,



    This router is in a Cisco lab in Building 17.  If having access to it would help, I can do that easily, or if you¿d like to discuss the issue, that is easy too!



    Thanks,

    Tony



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Thursday, October 07, 2010 3:51 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Radhika Miriyala in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Tony Anderson in Service Ready Engine Virtualization -



    Radhika Miriyala has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Tony,

    1) Can you please give your interface vlan1 config?



    interface Vlan1

    description SM2 MGF

    ip address 172.28.207.33 255.255.255.252


    2) Can you ping the Hypervisor Ip from the router?

    no

    3) Output of show license in-use

    StoreIndex:  0  Feature: SRE-V-HOST-LIC                    Version: 1.0

            License Type: Evaluation

            License State: Active, In Use

                Evaluation total period:  8 weeks  4 days

                Evaluation period left:  8 weeks  4 days

                Expiry date: Sat Mar  1 01:41:30 2008

            License Count: Non-Counted

            License Priority: Low.


    4) Output of ¿show hypervisor nics¿ for sm 2/0
    Name    PCI           Driver      Link Speed     Duplex MAC Address       MTU

    vmnic1  0000:01:00.00 e1000e      Down 0Mbps     Half   c8:4c:75:23:a2:61 1500

    vmnic2  0000:02:00.00 bnx2        Up   1000Mbps  Full   68:ef:bd:f9:9a:41 1500

    vmnic3  0000:02:00.01 bnx2        Up   1000Mbps  Full   68:ef:bd:f9:9a:40 1500


    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Thursday, October 07, 2010 12:05 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Tony Anderson in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Kevin Marraccini in Service Ready Engine Virtualizatio



    Tony Anderson has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    I am running in to the same issue.

    interface SM1/0
    ip address 172.28.207.17 255.255.255.252
    service-module ip address 172.28.207.18 255.255.255.252
    !Application: SRE-V Running on SMV
    service-module ip default-gateway 172.28.207.17
    service-module mgf ip address 172.28.207.34 255.255.255.252
    service-module mgf ip default-gateway 172.28.207.33
    !
    interface SM1/1
    description Internal switch interface connected to Service Module
    switchport mode trunk
    !
    interface SM2/0
    ip address 172.28.207.21 255.255.255.252
    service-module ip address 172.28.207.22 255.255.255.252
    !Application: SRE-V Running on SMV
    service-module ip default-gateway 172.28.207.21
    service-module mgf ip address 172.28.207.38 255.255.255.252
    service-module mgf ip default-gateway 172.28.207.37
    !
    interface SM2/1
    description Internal switch interface connected to Service Module
    switchport mode trunk

    se-172-28-207-18# sh hypervisor ip
    Hostname: localhost
    Domain Name: None
    IP Config: 172.28.207.34(Subnet Mask: 255.255.255.248)
    169.254.1.1(Subnet Mask: 255.255.255.0)
    Default Gateway: 172.28.207.33
    Preferred DNS Server: None
    Alternative DNS Server: None

    se-172-28-207-22# sh hypervisor ip
    Hostname: localhost
    Domain Name: None
    IP Config: 172.28.207.38(Subnet Mask: 255.255.255.252)
    169.254.1.1(Subnet Mask: 255.255.255.0)
    Default Gateway: 172.28.207.37
    Preferred DNS Server: None
    Alternative DNS Server: None


    Thanks,
    Tony
    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2617617>
    or simply reply to this email.
    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2617650>
    or simply reply to this email.

    Subject: RE: New Message from Tony Anderson in Service Ready Engine Virtualization -
    Replied by: Radhika Miriyala on 20-11-2010 01:34:17 AM
    Tony,

    Can we do a quick webex meeting where we can look at the setup and also discuss it that would be great. If webex will not work then please give me access to the router and I will take a look.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Thursday, October 07, 2010 1:12 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Tony Anderson in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Radhika Miriyala in Service Ready Engine Virtualizatio



    Tony Anderson has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Hi Radhika,



    This router is in a Cisco lab in Building 17. If having access to it would help, I can do that easily, or if you¿d like to discuss the issue, that is easy too!



    Thanks,

    Tony



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Thursday, October 07, 2010 3:51 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Radhika Miriyala in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Tony Anderson in Service Ready Engine Virtualization -



    Radhika Miriyala has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Tony,

    1) Can you please give your interface vlan1 config?



    interface Vlan1

    description SM2 MGF

    ip address 172.28.207.33 255.255.255.252


    2) Can you ping the Hypervisor Ip from the router?

    no

    3) Output of show license in-use

    StoreIndex: 0 Feature: SRE-V-HOST-LIC Version: 1.0

    License Type: Evaluation

    License State: Active, In Use

    Evaluation total period: 8 weeks 4 days

    Evaluation period left: 8 weeks 4 days

    Expiry date: Sat Mar 1 01:41:30 2008

    License Count: Non-Counted

    License Priority: Low.


    4) Output of ¿show hypervisor nics¿ for sm 2/0
    Name PCI Driver Link Speed Duplex MAC Address MTU

    vmnic1 0000:01:00.00 e1000e Down 0Mbps Half c8:4c:75:23:a2:61 1500

    vmnic2 0000:02:00.00 bnx2 Up 1000Mbps Full 68:ef:bd:f9:9a:41 1500

    vmnic3 0000:02:00.01 bnx2 Up 1000Mbps Full 68:ef:bd:f9:9a:40 1500


    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Thursday, October 07, 2010 12:05 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Tony Anderson in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Kevin Marraccini in Service Ready Engine Virtualizatio



    Tony Anderson has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    I am running in to the same issue.

    interface SM1/0
    ip address 172.28.207.17 255.255.255.252
    service-module ip address 172.28.207.18 255.255.255.252
    !Application: SRE-V Running on SMV
    service-module ip default-gateway 172.28.207.17
    service-module mgf ip address 172.28.207.34 255.255.255.252
    service-module mgf ip default-gateway 172.28.207.33
    !
    interface SM1/1
    description Internal switch interface connected to Service Module
    switchport mode trunk
    !
    interface SM2/0
    ip address 172.28.207.21 255.255.255.252
    service-module ip address 172.28.207.22 255.255.255.252
    !Application: SRE-V Running on SMV
    service-module ip default-gateway 172.28.207.21
    service-module mgf ip address 172.28.207.38 255.255.255.252
    service-module mgf ip default-gateway 172.28.207.37
    !
    interface SM2/1
    description Internal switch interface connected to Service Module
    switchport mode trunk

    se-172-28-207-18# sh hypervisor ip
    Hostname: localhost
    Domain Name: None
    IP Config: 172.28.207.34(Subnet Mask: 255.255.255.248)
    169.254.1.1(Subnet Mask: 255.255.255.0)
    Default Gateway: 172.28.207.33
    Preferred DNS Server: None
    Alternative DNS Server: None

    se-172-28-207-22# sh hypervisor ip
    Hostname: localhost
    Domain Name: None
    IP Config: 172.28.207.38(Subnet Mask: 255.255.255.252)
    169.254.1.1(Subnet Mask: 255.255.255.0)
    Default Gateway: 172.28.207.37
    Preferred DNS Server: None
    Alternative DNS Server: None


    Thanks,
    Tony
    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2617617>
    or simply reply to this email.
    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2617650>
    or simply reply to this email.
    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2617710>
    or simply reply to this email.

    Subject: RE: New Message from Radhika Miriyala in Service Ready Engine Virtualizatio
    Replied by: Tony Anderson on 20-11-2010 01:34:17 AM
    Radhika,



    Webex works.  Can you do it now?



    Thanks,

    Tony



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Thursday, October 07, 2010 4:16 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Radhika Miriyala in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Tony Anderson in Service Ready Engine Virtualization -



    Radhika Miriyala has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Tony,

    Can we do a quick webex meeting where we can look at the setup and also discuss it that would be great. If webex will not work then please give me access to the router and I will take a look.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Thursday, October 07, 2010 1:12 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Tony Anderson in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Radhika Miriyala in Service Ready Engine Virtualizatio



    Tony Anderson has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Hi Radhika,



    This router is in a Cisco lab in Building 17. If having access to it would help, I can do that easily, or if you¿d like to discuss the issue, that is easy too!



    Thanks,

    Tony



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Thursday, October 07, 2010 3:51 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Radhika Miriyala in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Tony Anderson in Service Ready Engine Virtualization -



    Radhika Miriyala has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Tony,

    1) Can you please give your interface vlan1 config?



    interface Vlan1

    description SM2 MGF

    ip address 172.28.207.33 255.255.255.252


    2) Can you ping the Hypervisor Ip from the router?

    no

    3) Output of show license in-use

    StoreIndex: 0 Feature: SRE-V-HOST-LIC Version: 1.0

    License Type: Evaluation

    License State: Active, In Use

    Evaluation total period: 8 weeks 4 days

    Evaluation period left: 8 weeks 4 days

    Expiry date: Sat Mar 1 01:41:30 2008

    License Count: Non-Counted

    License Priority: Low.


    4) Output of ¿show hypervisor nics¿ for sm 2/0
    Name PCI Driver Link Speed Duplex MAC Address MTU

    vmnic1 0000:01:00.00 e1000e Down 0Mbps Half c8:4c:75:23:a2:61 1500

    vmnic2 0000:02:00.00 bnx2 Up 1000Mbps Full 68:ef:bd:f9:9a:41 1500

    vmnic3 0000:02:00.01 bnx2 Up 1000Mbps Full 68:ef:bd:f9:9a:40 1500


    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Thursday, October 07, 2010 12:05 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Tony Anderson in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Kevin Marraccini in Service Ready Engine Virtualizatio



    Tony Anderson has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    I am running in to the same issue.

    interface SM1/0
    ip address 172.28.207.17 255.255.255.252
    service-module ip address 172.28.207.18 255.255.255.252
    !Application: SRE-V Running on SMV
    service-module ip default-gateway 172.28.207.17
    service-module mgf ip address 172.28.207.34 255.255.255.252
    service-module mgf ip default-gateway 172.28.207.33
    !
    interface SM1/1
    description Internal switch interface connected to Service Module
    switchport mode trunk
    !
    interface SM2/0
    ip address 172.28.207.21 255.255.255.252
    service-module ip address 172.28.207.22 255.255.255.252
    !Application: SRE-V Running on SMV
    service-module ip default-gateway 172.28.207.21
    service-module mgf ip address 172.28.207.38 255.255.255.252
    service-module mgf ip default-gateway 172.28.207.37
    !
    interface SM2/1
    description Internal switch interface connected to Service Module
    switchport mode trunk

    se-172-28-207-18# sh hypervisor ip
    Hostname: localhost
    Domain Name: None
    IP Config: 172.28.207.34(Subnet Mask: 255.255.255.248)
    169.254.1.1(Subnet Mask: 255.255.255.0)
    Default Gateway: 172.28.207.33
    Preferred DNS Server: None
    Alternative DNS Server: None

    se-172-28-207-22# sh hypervisor ip
    Hostname: localhost
    Domain Name: None
    IP Config: 172.28.207.38(Subnet Mask: 255.255.255.252)
    169.254.1.1(Subnet Mask: 255.255.255.0)
    Default Gateway: 172.28.207.37
    Preferred DNS Server: None
    Alternative DNS Server: None


    Thanks,
    Tony
    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2617617>
    or simply reply to this email.
    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2617650>
    or simply reply to this email.
    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2617710>
    or simply reply to this email.
    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2617712>
    or simply reply to this email.

    Subject: RE: New Message from Tony Anderson in Service Ready Engine Virtualization -
    Replied by: Radhika Miriyala on 20-11-2010 01:34:17 AM
    Tony, I will send out the webex for 2:00 to 2:30 hopefully this works for you .

    Thanks,

    Radhika

    Subject: RE: New Message from Radhika Miriyala in Service Ready Engine Virtualizatio
    Replied by: Tony Anderson on 20-11-2010 01:34:17 AM
    Hi Radhika,



    No go!  The hypervisor is picking up the wrong subnet mask and not picking up the default gateway (which makes a little sense, since the default gateway address is out of the subnet for the mask it¿s picking up).



    interface SM1/0

    ip address 172.28.207.17 255.255.255.252

    service-module ip address 172.28.207.18 255.255.255.252

    !Application: SRE-V Running on SMV

    service-module ip default-gateway 172.28.207.17

    service-module mgf ip address 172.28.207.34 255.255.255.248

    service-module mgf ip default-gateway 172.28.207.33

    !

    interface SM1/1

    description Internal switch interface connected to Service Module

    switchport mode trunk

    !        

    interface SM2/0

    ip address 172.28.207.21 255.255.255.252

    service-module ip address 172.28.207.22 255.255.255.252

    !Application: SRE-V Running on SMV

    service-module ip default-gateway 172.28.207.21

    service-module mgf ip address 172.28.207.38 255.255.255.248

    service-module mgf ip default-gateway 172.28.207.33

    !

    interface SM2/1

    description Internal switch interface connected to Service Module

    switchport mode trunk



    interface Vlan1

    description SM1 MGF

    ip address 172.28.207.33 255.255.255.248



    SM1

    se-172-28-207-18# sh hypervisor ip

    Hostname:               localhost

    Domain Name:            None

    IP Config:              172.28.207.34(Subnet Mask: 255.255.255.248)

                            169.254.1.1(Subnet Mask: 255.255.255.0)

    Default Gateway:        172.28.207.33

    Preferred DNS Server:   None

    Alternative DNS Server: None



    SM2

    se-172-28-207-22# sh hypervisor ip

    Hostname:               localhost

    Domain Name:            None

    IP Config:              172.28.207.38(Subnet Mask: 255.255.255.252)

                            169.254.1.1(Subnet Mask: 255.255.255.0)

    Default Gateway:        None

    Preferred DNS Server:   None

    Alternative DNS Server: None



    I reset twice to make sure it wasn¿t a glitch.  Is there a way I can configure it on the SRE module?



    Thanks,
    Tony

    Subject: RE: New Message from Tony Anderson in Service Ready Engine Virtualization -
    Replied by: Radhika Miriyala on 20-11-2010 01:34:17 AM
    Tony,

    So after you changed the ip addressing and subnet mask on the router you rebooted the sm2/0? If after this also it is not getting the new subnet mask than it could be a bug. Can you please try a reload of the sm2/0 now and let me know if the issue still persists?



    Thanks,

    Radhika





    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Thursday, October 07, 2010 2:50 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Tony Anderson in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Radhika Miriyala in Service Ready Engine Virtualizatio



    Tony Anderson has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Hi Radhika,



    No go! The hypervisor is picking up the wrong subnet mask and not picking up the default gateway (which makes a little sense, since the default gateway address is out of the subnet for the mask it¿s picking up).



    interface SM1/0

    ip address 172.28.207.17 255.255.255.252

    service-module ip address 172.28.207.18 255.255.255.252

    !Application: SRE-V Running on SMV

    service-module ip default-gateway 172.28.207.17

    service-module mgf ip address 172.28.207.34 255.255.255.248

    service-module mgf ip default-gateway 172.28.207.33

    !

    interface SM1/1

    description Internal switch interface connected to Service Module

    switchport mode trunk

    !

    interface SM2/0

    ip address 172.28.207.21 255.255.255.252

    service-module ip address 172.28.207.22 255.255.255.252

    !Application: SRE-V Running on SMV

    service-module ip default-gateway 172.28.207.21

    service-module mgf ip address 172.28.207.38 255.255.255.248

    service-module mgf ip default-gateway 172.28.207.33

    !

    interface SM2/1

    description Internal switch interface connected to Service Module

    switchport mode trunk



    interface Vlan1

    description SM1 MGF

    ip address 172.28.207.33 255.255.255.248



    SM1

    se-172-28-207-18# sh hypervisor ip

    Hostname: localhost

    Domain Name: None

    IP Config: 172.28.207.34(Subnet Mask: 255.255.255.248)

    169.254.1.1(Subnet Mask: 255.255.255.0)

    Default Gateway: 172.28.207.33

    Preferred DNS Server: None

    Alternative DNS Server: None



    SM2

    se-172-28-207-22# sh hypervisor ip

    Hostname: localhost

    Domain Name: None

    IP Config: 172.28.207.38(Subnet Mask: 255.255.255.252)

    169.254.1.1(Subnet Mask: 255.255.255.0)

    Default Gateway: None

    Preferred DNS Server: None

    Alternative DNS Server: None



    I reset twice to make sure it wasn¿t a glitch. Is there a way I can configure it on the SRE module?



    Thanks,
    Tony



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Thursday, October 07, 2010 4:42 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Radhika Miriyala in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Tony Anderson in Service Ready Engine Virtualization -



    Radhika Miriyala has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Tony, I will send out the webex for 2:00 to 2:30 hopefully this works for you .



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Thursday, October 07, 2010 1:38 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Tony Anderson in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Radhika Miriyala in Service Ready Engine Virtualizatio



    Tony Anderson has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Radhika,



    Webex works. Can you do it now?



    Thanks,

    Tony



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Thursday, October 07, 2010 4:16 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Radhika Miriyala in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Tony Anderson in Service Ready Engine Virtualization -



    Radhika Miriyala has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Tony,

    Can we do a quick webex meeting where we can look at the setup and also discuss it that would be great. If webex will not work then please give me access to the router and I will take a look.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Thursday, October 07, 2010 1:12 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Tony Anderson in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Radhika Miriyala in Service Ready Engine Virtualizatio



    Tony Anderson has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Hi Radhika,



    This router is in a Cisco lab in Building 17. If having access to it would help, I can do that easily, or if you¿d like to discuss the issue, that is easy too!



    Thanks,

    Tony



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Thursday, October 07, 2010 3:51 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Radhika Miriyala in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Tony Anderson in Service Ready Engine Virtualization -



    Radhika Miriyala has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Tony,

    1) Can you please give your interface vlan1 config?



    interface Vlan1

    description SM2 MGF

    ip address 172.28.207.33 255.255.255.252


    2) Can you ping the Hypervisor Ip from the router?

    no

    3) Output of show license in-use

    StoreIndex: 0 Feature: SRE-V-HOST-LIC Version: 1.0

    License Type: Evaluation

    License State: Active, In Use

    Evaluation total period: 8 weeks 4 days

    Evaluation period left: 8 weeks 4 days

    Expiry date: Sat Mar 1 01:41:30 2008

    License Count: Non-Counted

    License Priority: Low.


    4) Output of ¿show hypervisor nics¿ for sm 2/0
    Name PCI Driver Link Speed Duplex MAC Address MTU

    vmnic1 0000:01:00.00 e1000e Down 0Mbps Half c8:4c:75:23:a2:61 1500

    vmnic2 0000:02:00.00 bnx2 Up 1000Mbps Full 68:ef:bd:f9:9a:41 1500

    vmnic3 0000:02:00.01 bnx2 Up 1000Mbps Full 68:ef:bd:f9:9a:40 1500


    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Thursday, October 07, 2010 12:05 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Tony Anderson in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Kevin Marraccini in Service Ready Engine Virtualizatio



    Tony Anderson has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    I am running in to the same issue.

    interface SM1/0
    ip address 172.28.207.17 255.255.255.252
    service-module ip address 172.28.207.18 255.255.255.252
    !Application: SRE-V Running on SMV
    service-module ip default-gateway 172.28.207.17
    service-module mgf ip address 172.28.207.34 255.255.255.252
    service-module mgf ip default-gateway 172.28.207.33
    !
    interface SM1/1
    description Internal switch interface connected to Service Module
    switchport mode trunk
    !
    interface SM2/0
    ip address 172.28.207.21 255.255.255.252
    service-module ip address 172.28.207.22 255.255.255.252
    !Application: SRE-V Running on SMV
    service-module ip default-gateway 172.28.207.21
    service-module mgf ip address 172.28.207.38 255.255.255.252
    service-module mgf ip default-gateway 172.28.207.37
    !
    interface SM2/1
    description Internal switch interface connected to Service Module
    switchport mode trunk

    se-172-28-207-18# sh hypervisor ip
    Hostname: localhost
    Domain Name: None
    IP Config: 172.28.207.34(Subnet Mask: 255.255.255.248)
    169.254.1.1(Subnet Mask: 255.255.255.0)
    Default Gateway: 172.28.207.33
    Preferred DNS Server: None
    Alternative DNS Server: None

    se-172-28-207-22# sh hypervisor ip
    Hostname: localhost
    Domain Name: None
    IP Config: 172.28.207.38(Subnet Mask: 255.255.255.252)
    169.254.1.1(Subnet Mask: 255.255.255.0)
    Default Gateway: 172.28.207.37
    Preferred DNS Server: None
    Alternative DNS Server: None


    Thanks,
    Tony
    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2617617>
    or simply reply to this email.
    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2617650>
    or simply reply to this email.
    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2617710>
    or simply reply to this email.
    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2617712>
    or simply reply to this email.
    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2621479>
    or simply reply to this email.
    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2617748>
    or simply reply to this email.
    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2621576>
    or simply reply to this email.

    Subject: RE: New Message from Kevin Marraccini in Service Ready Engine Virtualizatio
    Replied by: Brett Tiller on 20-11-2010 01:34:17 AM
    Kevin,
     
    Please make sure you've set up a vlan 1 interface and that the mfg interface ip default-gateway is synch up with it.  I don't see this in the data you provided.
     
    Brett

    Subject: RE: New Message from Radhika Miriyala in Service Ready Engine Virtualizatio
    Replied by: Radhika Miriyala on 20-11-2010 01:34:17 AM
    One more thing you can set the default gateway on the module using the cli ¿hypervisor set ip default-gateway x.x.x.x¿ there is no way to set the subnet on the module using cli. You can do it from the Vsphere client but if you have networking issues obviously that won¿t work.

    Subject: RE: New Message from Brett Tiller in Service Ready Engine Virtualization -
    Replied by: Tony Anderson on 20-11-2010 01:34:17 AM
    Hi Brett,



    Vlan 1 config was after the SM 2/1 config and before the show hypervisor IP output.



    Thanks,

    Tony



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Thursday, October 07, 2010 5:56 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Brett Tiller in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Kevin Marraccini in Service Ready Engine Virtualizatio



    Brett Tiller has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Kevin,

    Please make sure you've set up a vlan 1 interface and that the mfg interface ip default-gateway is synch up with it.  I don't see this in the data you provided.

    Brett
    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2621580>
    or simply reply to this email.

    Subject: RE: New Message from Radhika Miriyala in Service Ready Engine Virtualizatio
    Replied by: Tony Anderson on 20-11-2010 01:34:17 AM
    I rebooted the SM twice, and just rebooted the router and reset each SRE again.  Same symptom.  I have a request in to my lab guy to power cycle the router.  One of the disadvantages of being on the other coast. J  It wouldn¿t let me set the default gateway.  ¿Failed to set the ip default gateway. Error: Unable to set VMkernel gateway address to 172.28.207.33 as there are no VMkernel interfaces on the same network with that IP address.¿



    I¿ll let you know if power cycling the router works, as soon as it gets cycled.



    Thanks,

    Tony

    Subject: RE: New Message from Tony Anderson in Service Ready Engine Virtualization -
    Replied by: Radhika Miriyala on 20-11-2010 01:34:17 AM
    Can you please list the exact steps you did to change the Ip addess and gateway on the ios side?  I would like to see if I can reproduce it in case it is a bug.



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Thursday, October 07, 2010 3:16 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from Tony Anderson in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from Radhika Miriyala in Service Ready Engine Virtualizatio



    Tony Anderson has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    I rebooted the SM twice, and just rebooted the router and reset each SRE again. Same symptom. I have a request in to my lab guy to power cycle the router. One of the disadvantages of being on the other coast. J It wouldn¿t let me set the default gateway. ¿Failed to set the ip default gateway. Error: Unable to set VMkernel gateway address to 172.28.207.33 as there are no VMkernel interfaces on the same network with that IP address.¿



    I¿ll let you know if power cycling the router works, as soon as it gets cycled.



    Thanks,

    Tony

    Subject: RE: New Message from Radhika Miriyala in Service Ready Engine Virtualizatio
    Replied by: Tony Anderson on 20-11-2010 01:34:18 AM
    You bet!



    Conf t

    Interface sm 1/0

    No service-module mfg ip default-gateway 172.28.207.3

    No service-module mfg ip address 172.28.207.34 255.255.255.252

    Service-module mfg ip address 172.28.207.34 255.255.255.248

    Service-module mfg default-gateway 172.28.207.33



    Interface sm 2/0

    No service-module mfg ip default-gateway 172.28.207.37

    No service-module mfg ip address 172.28.207.38 255.255.255.252

    Service-module mfg ip address 172.28.207.38 255.255.255.248

    Service-module mfg default-gateway 172.28.207.33



    Interface vlan 1

    No ip address 172.28.207.33 255.255.255.252

    Ip address 172.28.207.33 255.255.255.248



    Thanks,

    Tony

    Subject: RE: New Message from Radhika Miriyala in Service Ready Engine Virtualizatio
    Replied by: Tony Anderson on 20-11-2010 01:34:18 AM
    Got it!  When I was typing in the steps below I remembered I didn¿t change the cgf ip address, just the mask and the default gateway.  I just changed the cgf ip and reloaded and it worked.  So the bug is if you don¿t change the IP address but change the mask, the system doesn¿t pick up the change.



    Thanks for all of your help!



    Tony



    You bet!



    Conf t

    Interface sm 1/0

    No service-module mfg ip default-gateway 172.28.207.3

    No service-module mfg ip address 172.28.207.34 255.255.255.252

    Service-module mfg ip address 172.28.207.34 255.255.255.248

    Service-module mfg default-gateway 172.28.207.33



    Interface sm 2/0

    No service-module mfg ip default-gateway 172.28.207.37

    No service-module mfg ip address 172.28.207.38 255.255.255.252

    Service-module mfg ip address 172.28.207.38 255.255.255.248

    Service-module mfg default-gateway 172.28.207.33



    Interface vlan 1

    No ip address 172.28.207.33 255.255.255.252

    Ip address 172.28.207.33 255.255.255.248



    Thanks,

    Tony

    Subject: RE: New Message from Tony Anderson in Service Ready Engine Virtualization -
    Replied by: Radhika Miriyala on 20-11-2010 01:34:18 AM
    Thanks Tony. I will file a bug so we can track it.