Unable to session into SRE following hwic-9esw removal.

Version 1
    This document was generated from CDN thread

    Created by: STEVEN BOLTON on 20-11-2010 01:33:51 AM
    Refer to the post "Loadting the SRE with ESXi for background details"
     
    This is a second SRE on a second 2911 router now without the hwic-9esw
    CISCO2911/K9
    Beta IOS and Beta SRE code installed.  One Guest OS instralled and running.
    WIC Slot 0:  VWIC2-2MFT-T1/E1
    WIC Slot 1:  HWIC-3G-CDMA-V
    Slot 1:         SM-SRE-900-K9
     
    ip route has been added to the config and still unalbe to ping 192.168.74.51 from the router.
    ip route 192.168.74.51 255.255.255.255 SM1/0
     
    Output of show tech attached.

    Subject: RE: Unable to session into SRE following hwic-9esw removal.
    Replied by: STEVEN BOLTON on 20-11-2010 01:33:54 AM
    Module error just after submitting post:
     
    SREUnit2#service-module sm1/0 status
    Service Module is Cisco SM1/0
    Service Module supports session via TTY line 67
    Service Module is trying to recover from error
    Service Module heartbeat-reset is enabled
    Service Module is in fail open
    Service Module status is not available
    No install/uninstall in progress

    Local Partition Info
    =====================
      Please reset module to retrieve
      partition information if needed

    SREUnit2#

    Subject: RE: New Message from STEVEN BOLTON in Service Ready Engine Virtualization -
    Replied by: Ashwin Venkatesan on 20-11-2010 01:33:54 AM
    Please try



    # service-module sm 1/0 session clear

    #service -module sm 1/0 session



    To see if it helps.



    Thanks,

    ashwin



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Wednesday, September 15, 2010 4:20 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from STEVEN BOLTON in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: Unable to session into SRE following hwic-9esw removal.



    STEVEN BOLTON has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Module error just after submitting post:

    SREUnit2#service-module sm1/0 status
    Service Module is Cisco SM1/0
    Service Module supports session via TTY line 67
    Service Module is trying to recover from error
    Service Module heartbeat-reset is enabled
    Service Module is in fail open
    Service Module status is not available
    No install/uninstall in progress

    Local Partition Info
    =====================
      Please reset module to retrieve
      partition information if needed

    SREUnit2#
    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2543187>
    or simply reply to this email.

    Subject: RE: New Message from STEVEN BOLTON in Service Ready Engine Virtualization -
    Replied by: STEVEN BOLTON on 20-11-2010 01:33:54 AM
    Did that many times.  The issue appears to be that the SRE still has some of the old parameters from when the hwic was installed.
     
    i.e.
              interface SM1/1
               description Internal switch interface connected to Service Module
               ip address 192.168.74.150 255.255.255.128
               service-module ip address 192.168.74.151 255.255.255.128

     
     
    * It did recover shortly after the error status.
     
    SREUnit2#service-module sm1/0 status
    Service Module is Cisco SM1/0
    Service Module supports session via TTY line 67
    Service Module is in Steady state
    Service Module heartbeat-reset is enabled
    Getting status from the Service Module, please wait..
    Cisco SRE-V Software 1.0.0.19
    SRE-V Running on SMV
    No install/uninstall in progress

    No local partition


    SREUnit2#service-module sm1/0 session
    Trying 192.168.74.50, 2067 ... Open

    SREUnit2#service-module sm1/0 session clear

     
    SREUnit2#
    [Resuming connection 1 to 192.168.74.50 ... ]

    [Connection to 192.168.74.50 closed by foreign host]
    SREUnit2#

    Subject: RE: New Message from STEVEN BOLTON in Service Ready Engine Virtualization -
    Replied by: STEVEN BOLTON on 20-11-2010 01:33:54 AM
    Things are still clearing up.  It has rebooted twice following tracebacks.  I can now session into it.  The hypervisor shows the following:
     
    VeronaSRE# show hypervisor ip
    Hostname:               localhost
    Domain Name:            None
    IP Config:              192.168.74.151(Subnet Mask: 255.255.255.128)
                            169.254.1.1(Subnet Mask: 255.255.255.0)
    Default Gateway:        192.168.74.150
    Preferred DNS Server:   None
    Alternative DNS Server: None

    VeronaSRE#
     
    Reconfiguring and will follow up with results.

    Subject: RE: New Message from STEVEN BOLTON in Service Ready Engine Virtualization -
    Replied by: Ashwin Venkatesan on 20-11-2010 01:33:54 AM
    Can you please share the tracebacks, so we can decode to see what is going on



    Thanks,

    Ashwin



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Wednesday, September 15, 2010 4:32 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from STEVEN BOLTON in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from STEVEN BOLTON in Service Ready Engine Virtualization -



    STEVEN BOLTON has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    Things are still clearing up.  It has rebooted twice following tracebacks.  I can now session into it.  The hypervisor shows the following:

    VeronaSRE# show hypervisor ip
    Hostname:               localhost
    Domain Name:            None
    IP Config:              192.168.74.151(Subnet Mask: 255.255.255.128)
                            169.254.1.1(Subnet Mask: 255.255.255.0)
    Default Gateway:        192.168.74.150
    Preferred DNS Server:   None
    Alternative DNS Server: None

    VeronaSRE#

    Reconfiguring and will follow up with results.
    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2543192>
    or simply reply to this email.

    Subject: RE: New Message from STEVEN BOLTON in Service Ready Engine Virtualization -
    Replied by: STEVEN BOLTON on 20-11-2010 01:33:54 AM
    -Traceback= 0x219AD4E4z 0x21A383CCz 0x21A38EB4z 0x214C7E44z 0x214C7F3Cz 0x223FBCCCz 0x223B41D8z 0x223B4DC0z 0x224517E4z 0x223F7270z 0x223FD98Cz 0x2241D984z 0x2241DBB4z 0x2241E038z 0x2241E35Cz 0x2240C194z

    Subject: RE: New Message from STEVEN BOLTON in Service Ready Engine Virtualization -
    Replied by: STEVEN BOLTON on 20-11-2010 01:33:55 AM
    How do I clean up the hypervisor settings?  Shouldn't the command:
         "service-module ip address 192.168.74.51 255.255.255.192"
    set the hypervisor parameter shown on the output of "show hypervisor ip"
         IP Config:              192.168.74.151(Subnet Mask: 255.255.255.128)
     
     
    When I enter the default gateway command, I get the following error:
    VeronaSRE# hypervisor set ip default-gateway 192.168.74.50
    Failed to set the ip default gateway. Error: Unable to set VMkernel gateway address to 192.168.74.50 as there are no VMkernel interfaces on the same network with that IP address.
    VeronaSRE#

    Subject: Re: New Message from STEVEN BOLTON in Service Ready Engine Virtualization -
    Replied by: Anurag Gurtu on 20-11-2010 01:33:55 AM
    The gateway IP should be same as the IP address of VLAN1 you configured in the router.

    Hypervisor IP is MGF IP that you set using IOS CLI.


    Thanks

    Anurag Gurtu

    On Sep 15, 2010, at 4:42 PM, "Cisco Developer Community Forums" <cdicuser@developer.cisco.com> wrote:

    > STEVEN BOLTON has created a new message in the forum "SRE-V Beta Testing":
    > --------------------------------------------------------------
    > How do I clean up the hypervisor settings?  Shouldn't the command:
    >      "service-module ip address 192.168.74.51 255.255.255.192"
    > set the hypervisor parameter shown on the output of "show hypervisor ip"
    >      IP Config:              192.168.74.151(Subnet Mask: 255.255.255.128)


    > When I enter the default gateway command, I get the following error:
    > VeronaSRE# hypervisor set ip default-gateway 192.168.74.50
    > Failed to set the ip default gateway. Error: Unable to set VMkernel gateway address to 192.168.74.50 as there are no VMkernel interfaces on the same network with that IP address.
    > VeronaSRE#
    > --
    > To respond to this post, please click the following link:
    > <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2543213>
    > or simply reply to this email.

    Subject: RE: New Message from STEVEN BOLTON in Service Ready Engine Virtualization -
    Replied by: Radhika Miriyala on 20-11-2010 01:33:55 AM
    Steve,

    The IP address assigned to ¿service-module ip address 192.168.74.51 255.255.255.192" is used by the console manager. Since you removed the HWIC-9ESW from your router now the way to configure the Hypervisor is through the CLI ¿ service-module mgf ip address 192.168.x.x 255.255.255.0¿



    The address you assign to the mgf will be used by the hypervisor and will show up in show hypervisor ip output.



    Please reload the SRE module after you change the IP address on the router.



    Thanks,

    Radhika



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Wednesday, September 15, 2010 4:43 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from STEVEN BOLTON in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from STEVEN BOLTON in Service Ready Engine Virtualization -



    STEVEN BOLTON has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    How do I clean up the hypervisor settings?  Shouldn't the command:
         "service-module ip address 192.168.74.51 255.255.255.192"
    set the hypervisor parameter shown on the output of "show hypervisor ip"
         IP Config:              192.168.74.151(Subnet Mask: 255.255.255.128)


    When I enter the default gateway command, I get the following error:
    VeronaSRE# hypervisor set ip default-gateway 192.168.74.50
    Failed to set the ip default gateway. Error: Unable to set VMkernel gateway address to 192.168.74.50 as there are no VMkernel interfaces on the same network with that IP address.
    VeronaSRE#
    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2543213>
    or simply reply to this email.

    Subject: RE: New Message from STEVEN BOLTON in Service Ready Engine Virtualization -
    Replied by: Ashwin Venkatesan on 20-11-2010 01:33:55 AM
    I decoded the traceback and it seems to be benign . You can ignore it for now



    Thanks

    Ashwin



    From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
    Sent: Wednesday, September 15, 2010 4:38 PM
    To: cdicuser@developer.cisco.com
    Subject: New Message from STEVEN BOLTON in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from STEVEN BOLTON in Service Ready Engine Virtualization -



    STEVEN BOLTON has created a new message in the forum "SRE-V Beta Testing":
    --------------------------------------------------------------
    -Traceback= 0x219AD4E4z 0x21A383CCz 0x21A38EB4z 0x214C7E44z 0x214C7F3Cz 0x223FBCCCz 0x223B41D8z 0x223B4DC0z 0x224517E4z 0x223F7270z 0x223FD98Cz 0x2241D984z 0x2241DBB4z 0x2241E038z 0x2241E35Cz 0x2240C194z
    --
    To respond to this post, please click the following link:
    <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2543208>
    or simply reply to this email.

    Subject: RE: New Message from STEVEN BOLTON in Service Ready Engine Virtualization -
    Replied by: STEVEN BOLTON on 20-11-2010 01:33:55 AM
    All is working now as expected.  I am pinging my laptop from a windows instance on the  SRE.  Thanks for you help.
     
    FYI:
    interface SM1/0
     ip address 192.168.74.50 255.255.255.192
     service-module ip address 192.168.74.51 255.255.255.192
     !Application: SRE-V Running on SMV
     service-module ip default-gateway 192.168.74.50
     service-module mgf ip address 192.168.74.151 255.255.255.192
     service-module mgf ip default-gateway 192.168.74.129
     hold-queue 60 out
    end

    SREUnit2#service-module sm1/0 session
    Trying 192.168.74.50, 2067 ... Open
    VeronaSRE#
    VeronaSRE# sh hyper ip
    Hostname:               localhost
    Domain Name:            None
    IP Config:              192.168.74.151(Subnet Mask: 255.255.255.128)
                            169.254.1.1(Subnet Mask: 255.255.255.0)
    Default Gateway:        192.168.74.129
    Preferred DNS Server:   None
    Alternative DNS Server: None

    VeronaSRE#